Search Documents

By Edward L. McHugh, Stanley M. Miller, Jeffrey K. Whyatt

The point estimation method can be applied to the safety factor (SF) equation for any specified rock slope failure mode (such as plane shear, step path, or wedge) to obtain reliable estimates of the mean and standard deviation of the SF probability distribution. A gamma probability density function is recommended for modeling this probability distribution, because it allows only for positive values and is flexible enough to provide symmetrical shapes and right-skewed, exponential-type shapes for the SF distribution. The mean and standard deviation define this distribution, which then can be integrated numerically from 0 to 1 to obtain the probability of sliding, PS (portion of the SF distribution where SF < 1.0). The overall probability of failure, PF, for the potential slope failure mass is the joint probability that the rock discontinuities are long enough to allow kinematic failure (PL) and that sliding occurs along the rock discontinuities (PS); that is, PF = PSPL. This method for estimating the probability of sliding is extremely efficient computationally, and thus, expedites slope stability simulation routines used by NIOSH software to stochastically describe rock slope behavior and assist the engineer in designing catch benches for large rock slopes. Enhanced bench design translates into increased operational efficiency and safer working conditions in open pit mines and quarries.

By Ren G. Dong, John Z. Wu, Daniel E. Welcome, Kristine Krajnak

Although the exact mechanisms underlying vibration white finger (VWF) are not clear, it has been speculated that VWF is associated with variations of the blood flow patterns due to the physical damage and/or degeneration in neural and vascular tissue caused by vibration loading [1]. Excessive dynamic deformation of the soft tissues in the fingertip under vibration loading is believed to induce multiple occupation-related hand/finger disorders. However, the in vivo distributions of the dynamic stress/strain of the tissues in the fingertip under vibration conditions have not been studied because they cannot be measured experimentally to date. The goal of this study is to analyze, theoretically, the location and frequency-dependent dynamic deformation of the soft tissue in the fingertip during vibration exposures. [ ] Methods The fingertip considered in the model is the distal phalanx, the portion from the distal end of the fingertip to the distal interphalangeal (DIP) joint articulation (Fig. 1). The external shape of the fingertip was determined using a smooth mathematical surface fitting to the observed fingertip shapes. The fingertip surface was then scaled to the dimensions of a typical male index finger: length 25 mm, width 20 mm, and height 18 mm. The fingertip was approximated to be symmetric, such that only a half of the fingertip was considered in the FE modeling. The fingertip was assumed to be composed of outer and inner skin layers, subcutaneous tissue, bone, and nail. The soft tissues (inner skin layer and subcutaneous tissues) were assumed to be nonlinearly elastic and viscoelastic, while the bone, nail, and outer skin layer were considered as linearly elastic. The simulations were conducted using a displacement-controlled protocol in two stages. First, the fingertip was statically pre-compressed. The contact plate was first displaced towards the finger to achieve a predetermined value of tissue deformation (i.e., 0.5, 1.0, 1.5, and 2.0 mm). Second, the steady-state dynamics responses of the fingertip were analyzed using a linear perturbation procedure. The fingertip was subjected to a continuous harmonic excitation (magnitude 0.5 mm) from the contact interface. The dynamic analysis was performed in a frequency domain ranging from 16 to 2000 Hz. The frequency-dependent distributions of the vibration magnitude and dynamic strain magnitudes in the soft tissues are investigated. Results Typical simulation results for the frequency-dependent distributions of the vibration magnitude in the soft tissues are shown in Fig. 2 (figures show the results with a pre-compression of 2.0 mm). The vibration magnitude at the contact surface is 0.5 mm (specified) for all frequencies, while the vibration magnitudes in the soft tissues are location- and frequency-dependent. It is clear that the fingertip has a major resonance around 125 Hz, at which the vibration magnitudes in the soft tissues are over four times greater than that of the contact plate (0.5 mm). It is interesting to observe that, at this resonant frequency (125 Hz), the soft tissues at the tip has the maximal vibration magnitude while the regions near the contact

Jan 6, 2006

1. In 2002, a total of 7,125 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA). The largest percentage of all mining sectors1 was sand and gravel mines (49.1%). Sand and gravel mines are found throughout all 50 states.

Jan 1, 2004

By Jueun Lee, Jong-Hwa Yoon, K. Rider, Bernard J. Martin

Whole body vibration is known to affect movement accuracy [1], however little is known about changes in the organization of movement and movement strategies used to limit the influences of perturbations. The specific aim of this work is to analyze the motion and coordination of upper body segments of seated operators performing reaching tasks under whole-body sinusoidal vibration exposure and simulated vehicle ride motion. The long-term objective is to model reach coordination and predict the dynamic behavior of the upper body motion under vehicle vibration exposure. Method The reach task consisted of pointing with the right hand index finger to targets located on touch screens placed in front of the subject, 45° overhead and 90° to the right in the mockup cabin of an HMMWV placed on a 6 DOF ride motion simulator. The task was performed under stable (no vibration) and vibration (sinusoidal vibration or simulated ride motion) conditions. A motion capture system was used to record kinematic data of reflective markers to recreate body link trajectories. Joint angles (torso, shoulder and elbow; Figure 1) were then computed using quaternions. Coordination between body links was defined as a) the joints angle-versus-angle relationships between the upper arm and lower arm, and b) the joint motion onset relationships between torso, upper arm and lower arm in the time domain. Results Angle–versus-angle relationships. The relationship between upper arm vs. lower arm angle and torso vs. upper arm angle for a far forward reaching movement in the stable (solid lines) and vibration conditions (dotted lines) are illustrated in Figure 2. Fig 2A compares the control condition with a 4 Hz lateral vibration while Fig 2B compares the control condition with a 6 Hz vertical vibration. It appears that under vibration exposure the reduced upper arm extension is compensated by an increase in torso flexion. This effect is seen in the last phase of the movements (encircled areas). In addition, the lower arm extension is delayed under 6 Hz vertical vibration (Fig 2B left panel). Time of joint motion onset. The timing relationship between torso, upper arm and lower arm is largely a function of the target to be reached. Examples of delays between body links are illustrated in Figure 3. The control condition is compared to a 6 Hz vertical vibration for three

Jan 6, 2006

By R. Karl Zipf, Kousick Biswas

The main objective of occupational health and safety research is to minimize or eliminate the events that may cause fatal or non-fatal injuries to human workers. A commonly used technique is to devise an “incident prevention plan”, which is more often the product of thorough investigations of past reported incident events. Incident documentation and methodical reporting and systematic and thorough data collection, often help identify the root cause of the incident – in other words, the etiology of the incident. These retrospective analyses of the incidents can efficiently identify the future steps to take to achieve the objective of minimizing occurrence of “events of interest”. This paper introduces a novel technique – “Taxonomic Analysis”, which identifies the root causes of an event (an incident in this case) and can provide future direction for corrective measures to reduce the probability of occurrence of the event. A taxonomic analysis involves systematic and organization of data based on observation, description, and classification. This paper utilizes the rock fall related incident narratives, available with the Mine Safety and Health Administration (MSHA) database (1984-1999), for a taxonomic analysis. The study found that 67.6% of groundfall incidents occurred in supported areas with the remainder (32.4%) in unsupported areas. Some form of rock mass failure appears to cause about 50% of groundfall incidents, although in 39.7% of the overall groundfall incidents or two-thirds of those involving rock mass failure, the exact nature of the rock mass failure could not be determined from the narratives. Human activities factors such as scaling or barring down, drilling or bolting, and setting timbers or cribbing accounted for another 34.5% of the groundfall incidents. Finally, support system failures made up the remaining 15.5%. Results from this taxonomic analysis may suggest focus areas toward which preventive measures and future research activities could concentrate.

By F. Fraas

ELECTROSTATIC methods are used to separate and concentrate or purify granular particles derived from ores or various synthetic and agricultural products. Compared with other separation methods that require many technological refinements, the electrostatic attraction of fibers, grass, and seeds to charged surfaces clan be accomplished under the most primitive circumstances, and the early development of this method of beneficiation seemed very promising. Precise application of the method to provide high selectivity, however, is a complex procedure, and interest in this method declined. During this period Mr. O. C. Ralston initiated a Bureau of Mines research program oil electrostatic separation. It is the purpose of thins publication to describe the development of the electrostatic method of particle separation from the early beginning to the present resurgence of interest. Most of the information for this description bas been derived from references, a few of which were not available for thorough review. Much information has been drawn from the investitions of the Bureau. Acknowledgments Mr. O. C. Ralston, former Chief metallurgist of the Bureau of Mines, began the research program on the subject and did research on the mils literature. Both Mr. Ralston and Mr. H. B. Johnson, former president of the Huff Electrostatic Separator Co., furnished patent references. A critical review by Mr. F. D. Lamb, Research director, and Mr. M. J. Spendlove, Supervisory metallurgist, Bureau of Mines, College Park Metallurgy Research Center, lifts been of much value in preparing this report.

Jan 1, 1962

By Dennis R. Dolinar, Gabriel S. Esterhuizen

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

By Grant R. Brown

The report provides guidance for determining those environmental impacts associated with the surface mining of steeply pitching coal seams. In addition to the environmental impacts, four additional issues are addressed, namely (1) Time and motion studies of those coal mining systems employed in mining seams which pitch in excess of 25°, (2) Assessment of those mining techniques, (3) Development of rationale for the mining methods employed, (4) Identification of the reclamation practices and determine whether these practices were in compliance with appropriate Federal and State regulations. Five surface mines located in three geologically distinct basins of the United States were analyzed during the period of August through November 1979. The three basins include the Hanna Basin of Wyoming, the North Park Basin of Colorado and the Southern Anthracite Field of Pennsylvania.

Jan 1, 1980

By R. A. Franks, G. F. Friel, J. C. Edwards, L. Yuan

Five mine fire experiments were conducted in a 2.08m high and 2.90m wide, ventilated mine entry in the National Institute for Occupational Safety and Health (NIOSH)&apos;s Safety Research Coal Mine (SRCM) to determine the effect of the dispersion of carbon monoxide (CO) on mine fire detection. CO measurements were made at distances from 7.6 m to 45.2 m downwind from the fire with diffusion mode CO sensors positioned near the roof. For small intensity fires, less than 30 kW heat release rate, generated by 14 kg coal in a 0.61 m square tray, it was determined that air flow and sensor spacing were significant for fire detection at the 10 ppm CO alarm level. Within 15.0 m downwind distance from the fire, 10 ppm CO alarm values occurred for volumetric air flows less than 11.5 m3/s. However, the 10 ppm CO alarm value did not occur 30.0 m downwind from the fire for air quantities greater than 6.2 m3/s due to dilutive mixing of the CO in the air stream. The criterion that the mine fire alarms occur within 15 min of the onset of flaming combustion could not be consistently met with the 10 ppm CO alarm. This suggests the use of lower CO alarm values, or reduced CO sensor spacings for mine fire protection. It is demonstrated how computational fluid dynamics (CFD) can be used to model the CO dispersion downwind from the fire in support of a plan to optimize sensor spacings.

By Russell G. Warncke

"This report is based primarily on a study of safety conditions and practices followed in the coal mines of Japan. Not all of the coal fields in Japan were studied, but typical mines in the largest producing areas and a fair cross section of coal-mine-safety conditions observed during February to April 1948 are described.Information was obtained through investigations conducted in the mines, discussions with mine-management officials and representatives of labor unions of the various mines visited, and examination of records and statistics from the various offices of the Coal Board of the Ministry of Commerce and Industry and from the Coal Association of Japan. Statistical data covering the same subject, obtained from different sources, varied in many respects and apparently were reported inaccurately, but such discrepancies can be attributed to different methods of reporting and compiling statistics.It is difficult to correlate the high fatal and nonfatal injury rates that prevail in Japanese coal mines with the conditions observed in the mines. Virtually all mines visited were attempting to prevent accidents and explosions, by apparently following known safety precautions for the prevention thereof. Some commendable safety innovations were observed at several mines; they indicated that mine officials are giving thought and consideration to hazardous conditions that affect their particular mines.Naturally, the operating officials and management were anxious to impress the writer with their interest in accident prevention and safety. Operating officials were found to be receptive to safety and wore interested in formulating definite safety programs. Some nines had well-planned and well-organized safety programs, which, if put into effect, would contribute greatly toward reduction of accidents.The approach to safety in Japan is quite different from that in the United States, especially the concept of personal responsibility for accidents and the extent to which the individual should be protected against hazards. Management is responsible for providing and maintaining safe working conditions. Collaboration between management and worker, as understood in the United States, does not exist in Japan.Increase in accidents since the cessation of hostilities is the result of unsettled economic conditions in the coal industry, influx of inexperience workers, and breakdown of discipline among the miners, who have been organized into unions. Those unions are greatly influenced by ""leftist"" tendencies.It was observed that the Japanese mine worker is fatalistic by nature and has little, if any, noticable safety consciousness. The most urgent major requirements to reduce accidents in the coal mines are to train the worker in accident prevention and instruct him regarding the inherent hazards of his occupation.Revision of the mining laws would help to reduce accidents if the companies would comply with such laws and provide safer working places and if the workers would cooperate with management and observe and comply with such laws as are enacted for their protection."

Dec 1, 1949

The importance of controlling respirable dust and methane gas levels in underground coal mining cannot be underestimated. While respirable dust can significantly affect the occupational health of underground coal miners, methane gas accumulations pose significant safety concerns for these same workers. Water sprays and machine mounted dust scrubbers offer effective control of respirable dust exposures and methane gas accumulations. Water must not only be applied carefully to avoid dust rollback to the machine operator but must create sufficient turbulence to remove dead zones that could contain high concentrations of methane gas. While the flooded-bed dust scrubber has been generally responsible for decreased worker exposures to respirable dusts, this device has proved effective in controlling methane levels at the face. This paper reviews practical applications of water sprays and dust scrubbers to control respirable dust and methane gas on continuous miner faces.

By Michael Schmitz, John A. Organiscak

ABSTRACT: A method (patent pending) has been developed to determine the quality of environmental cab filtration systems. This method utilizes specially configured filter cartridges to remove carbon dioxide from the ambient air with the environmental cab’s air filtration system. A real-time gas monitor is placed inside an unoccupied cab with the filtration system running to time decay the carbon dioxide to its lowest concentration or equilibrium level. The outside carbon dioxide concentration level can be measured concurrently with another gas monitor or with the same inside cab gas monitor during a representative period before and after the inside sampling is conducted. Cab filtration system leakage is comparatively deduced from the difference between the special cartridge filter efficiency and overall cab efficiency. Laboratory trials have illustrated that desirable high efficiency test filter configurations (greater than 99 % efficiency) can be devised, but have air quantity and test time limitations. These trials also demonstrated that CO2 penetration was reflective of controlled air leaks around a high efficiency filter under equilibrium conditions. This report examines the elements of this patent pending method.

To improve the level of hearing protection by providing workers with an inexpensive, easy-to-use device to check earplug fit. Background Approximately 30 million workers are exposed to hazardous noise on the job, placing them at risk of permanent hearing loss, tinnitus, and other disorders. Although the preferred solution is to eliminate noise through engineering controls or to reduce noise exposure through administrative controls, hearing protectors are critical when noise is unavoidable. Studies of hearing protector users have shown that average protection values in the real world are much lower than the labeled noise reduction ratings determined in laboratories with trained and motivated subjects. Even worse, many hearing pro­tector users get virtually no protection at all because of poor fit. The studies also show that users have a harder time achieving adequate protection levels with earplugs than with earmuffs. It?s difficult for users to tell if earplugs are working well just by looking at them. A more accurate approach is to check how much they block or ?attenuate? noise. Earplugs vary in their attenuation characteristics, with most providing a maximum of 20?35 decibels of noise reduction when worn correctly. Any earplug that?s suitable for use in noisy settings will attenuate noise by at least 15 decibels. Personal fit testing is an effective way to help hearing protector users improve the fit and protection levels of the devices. However, existing fit-testing systems are expensive and unsuitable for use at many industrial worksites.

Dec 1, 2008

By Robert W. Waytulonis

This publication contains 1,000 citations of technical and semi-technical literature treating diesel-powered equipment usage underground both generally and specifically. These citations were gathered by U.S. Bureau of Mines personnel over the period of 1978-1983. The citations concern diesel engines as powerplants for underground mining use; their design, emission characteristics and control, maintenance, usage; and health and safety aspects. All citations have been abstracted and arranged 1n a subject classification system with extensive cross-referencing.

Jan 1, 1983

By H. Nelisse, S. K. Patra, A. Natani, S. Rakheja

The current laboratory methods for assessing the vibration attenuation performance of seats involve repetitive trials with a number of human occupants, and raise certain ethical concerns. Moreover, the measurements with human subjects yield considerable variability in the data. Alternatively, several anthropodynamic manikins have been developed for effective assessments of the coupled seat occupant system [1]. The effectiveness of a manikin in predicting the response of a coupled seat-occupant system lies in its ability to reproduce the biodynamic response of the seated human body in terms of force-motion relationship at the body-seat interface, such as apparent mass (APMS). A number of prototype manikins have thus been developed on the basis of biodynamic characteristics of vertical vibration-exposed seated occupants of different body masses in the vicinity of 5th, 50th and 95th percentile male population. This study concerns with the analysis of a passive prototype manikin to enhance its ability to reproduce the idealized APMS response characteristics of the vibration-exposed seated human subjects defined in ISO-5982[2] for mean body masses of 55, 75 and 98 kg. Methods The APMS responses of a prototype anthropodynamic passive manikin were thoroughly characterized in the laboratory under different excitations and body mass configurations. The manikin was designed with sufficient flexibility to configure mechanical-equivalent models corresponding to seated body masses of 55, 75 and 98 kg, by adding/removing specified masses and springs (Fig. 1). The manikin, configured for a specific body mass, was positioned on a rigid seat without a backrest, which was fixed to the force platform of a whole-body vertical vibration simulator. The simulator was programmed to synthesize random vertical vibration with flat acceleration power spectrum in the 0.4-20 Hz frequency range with two different magnitudes: 1 and 2 m/s2 overall rms acceleration. The total static and dynamic forces of the manikin to and the seat were measured using the force platform, while a single axis accelerometer was installed on the seat pan to measure acceleration due to vertical excitation. The measured data was appropriately corrected for the rigid seat inertia force, and the apparent mass [ ]

Jan 6, 2006

By Douglas Ketcham, Thomas Jetzer

While the neurological and vascular aspects of Hand-Arm Vibration Syndrome (HAVS) has been generally accepted as a medical condition, the medical criteria and the clinical findings used to establish the diagnosis has been more difficult to bring to consensus. The criteria was first quantified by the Taylor-Palmear scale.1 This criteria was subsequently modified in 1986 at the 1st Stockholm Workshop2,3 to included more acceptance for the neurological effects that characterized the predominate findings in some workers. The relationship between hand-arm vibration and Carpal Tunnel Syndrome was defined in NIOSH 97-1414. While the aforementioned documents have defined the clinical entities associated with hand-arm vibration exposure, agreement on the clinical findings and test to confirm the diagnosis has be been more difficult to bring to consensus. Clinicians assessing HAVS has relied on a number of varied neurological and vascular tests. The neurological testing has focused on assessing damage to the sensory capability of the fingers for the neurological component including tests to measuring ability to sense vibration, cold or other end point finger sensor functions. However, the vascular testing has been traditionally focused on the ability to either measure vascular function or to reproduce the vascular blanching that occurs in HAVS with cold water provocation. Recent assessment of this testing in the United Kingdom Coal Miner’s study has questioned the value of this testing especially in reviews by McGeoch.5 In an attempt to provide some type of definitive testing to substantiate vascular damage from hand-arm vibration exposure, angiography is an alternative or adjunct to cold water provocation testing. The standards that have been established to predict the level, type and incidence of HAVS have been based on clinical studies and reports that have essentially been all male populations. However, the recent entry of women into more vibration intensive jobs has brought about the exposure of some women to high levels of vibration previously only previously experienced by men. However, there have been only few studies that look at HAVS in women6. Although exposed the same vibration levels, it has not been clear that the latency and type of pathology of HAVS in women will be the same as for men. The purpose of this study is to look at recent case studies of men and women exposed to jobs with high levels of hand-arm vibration with extensive clinical testing for both the neurological and vascular components of HAVS as well as other associated upper extremity conditions such as Carpal Tunnel Syndrome.

Jan 6, 2006

Mine drainage and mine reclamation are topics of major interest to the mining industry, federal and local governments, and the general public. This publication and its companion three volumes are the proceedings of a conference held in Pittsburgh, Pennsylvania, April 24-29, 1994. There were twelve sessions (69 papers) that dealt with mine drainage, including modeling, geochemistry, prediction, treatment, control strategies, characterization, hydrology, and case studies. These sessions comprise volumes 1 and 2. The six sessions (34 papers) that dealt with reclamation and revegetation of disturbed lands are included in volume 3. Volume 4 includes the six sessions (34 papers) that dealt with such topical issues as fires at abandoned mine sites, subsidence, hydrology, mine wastes, and policy. Poster session presentations are represented by 49 papers and 92 abstracts that have been placed in the back of volumes 2, 3, and 4, consistent with the subject of that volume.

Jan 1, 1994

By John A. Kost

Previous work performed under Contract H0220003 suggested that the mean incombustible content could be obtained with fewer samples and smaller samples without greatly increasing the sampling error. Under Modification No. 4 additional surveys were made in twelve coal mines, representing six states. Same 2,500 samples were collected, analyzed for incombustible content, and statistically evaluated. The earlier findings were substantiated.

Jan 1, 1975

By R. W. Courtney

The objective of this study is to make a critical evaluation of the magnitude and extent of electrostatic hazards in typical U.S. mining operations and to assess the adequacy of techniques, materials, and equipment for detecting and minimizing these hazards. This was accomplished with an incident/accident survey, mine visits, literature search, and engineering analysis. It was concluded that it would be desirable to (1) utilize ground fault interrupters to minimize stray current from electrical utilities, (2) decrease the current and electrostatic sensitivity of electric detonators used in areas with a high incidence of lightning strikes or troublesome stray currents, (3) institute quality control and test standards for blasting material and protective devices, (4) establish an electrostatic monitoring program for loading ANFO in plastic lined holes, and (5) establish a risk criteria for operator exposure in mines.

Jan 1, 1982

By R. R. Hornor, Harry E. Tufft

The purpose of this bulletin is to point out some of the benefits and economies to be derived by selecting, preparing, storing, preserving, and utilizing mine timber more carefully and to give some specific information on certain preservatives and processes suitable for mine timber.

Jan 1, 1925