Search Documents

By H. M. Lawrence, E. Roca

"INTRODUCTION Of the phosphate rock deposits of the United States that are being exploited actively at present, the land-pebble area in Florida is the largest producer. In recent years the land-pebble district, in Polk and Hillsborough Counties, has produced about 80 per cent of the raw phosphate rock that has supplied the requirements of the several national industries based on this essential commodity.In the land-pebble deposits sizes finer than 16 to 22 mesh are below the commercial limit in phosphate content, and washing-plant practice has been directed to the recovery of the coarser material. Recently, more extensive control of the washery plan has resulted in the saving of additional amounts of phosphate, the loss of which had been considered unavoidable. However, strict requirements of the trade regarding the lowest acceptable grade of phosphate rock prevent the inclusion of more than a very small proportion of the low-grade phosphatic sands with the washery output of phosphate roe:. Further advances in practice resulting in larger recoveries of phosphate can only be effected by the application of processes that are based on other principles than merely a difference of particle size. Research is be conducted actively along these lines by the industry and by cooperating agencies.Flotation has been studied for several years by the International Agricultural Corporation and its allied company, the Phosphate Recovery Corporation. J. T. Burrows, vice-president of the International Agricultural Corporation, in a letter dated July 10, 1929, states:"

Aug 1, 1931

By Edward A. Barrett, Kathleen M. Kowalski-Trakofler

This paper discusses the application of a training intervention that uses degraded images for improving the hazard recognition skills of miners. Method: NIOSH researchers, in an extensive literature review, identified fundamental psychological principles on perception that may be employed to enhance the ability of miners to recognize and respond to hazards in their dangerous work environment. Three studies were conducted to evaluate the effectiveness of the degraded image training intervention. A model of hazard recognition was developed to guide the study. Results: In the first study, miners from Pennsylvania, West Virginia and Alabama, who were taught with the aid of degraded images, scored significantly better on follow—up hazard recognition performance measures than those trained using traditional instructional methodologies. The second and third studies investigated the effectiveness of the training intervention at two mining companies. Data collected over a3—year period showed that lost—time injuries at mines in Alabama and Illinois declined soon after the training intervention was instituted. Impact on Industry: Further exploration of the hazard recognition model and the development of other interventions based on the model could support the validity of the steps in the hazard recognition model.

By E. A. Mihok

A pilot plant for treating mine drainage by neutralization with limestone was designed, fabricated, and operated by the Bureau of Mines. The process consists of (1) producing a very fine (minus 400-mesh) limestone slurry, (2) mixing the slurry with the mine water, (3) aerating the resulting mixture to remove carbon dioxide and precipitate iron, and (4) separating the solids from the liquid by sedimentation. A mine discharge of pH 2.8, containing 1,700 ppm total acidity, 36 ppm ferrous iron, and 360 ppm total iron, was treated at rates from 300 to 400 gpm. The treated water ultimately reached a pH of 7.4 and contained no detectable iron. The resulting sludge compacted to approximately one-third the volume of sludge from mine water neutralized with lime. The advantages of the limestone process, compared with the conventional lime process are as follows: Widespread distribution and lower cost of run-of-mine, indigenous limestone; simplicity of plant design; reduced hazards and plant operating and maintenance costs accruing from the use of a less reactive chemical agent; higher solids concentration of the precipitated sludge; and no deleterious effect caused by accidental overtreatment. While total process costs could not be determined, it is conservatively estimated that the cost of treating mine water by the limestone process is one-third to one-half the cost of the lime process, depending on the characteristics of the water to be treated and the availability and quality of limestone used.

Jan 1, 1968

By Jay C. Hanson

Various electrical and electromagnetic (EM) geophysical techniques are currently being evaluated by the U.S. Bureau of Mines for their effectiveness in the detection and monitoring of electrically conductive (1 to 5 S/m) lixiviant (leach solution) to depths of 600 m, either above or below the water table. These techniques include magnetotellurics (MT) , controlled source audiofrequency magnetotellurics (CSAMT), resistivity and focused resistivity, ground-penetrating radar (GPR), frequency-domain electromagnetics (FEM), and time-domain electromagnetics (TEM). Of these techniques, TEM may be the most effective, but CSAMT and focused resistivity also hold promise. Geophysical computer modeling of the borehole TEM technique was conducted based on an idealized geoelectric section (layered earth) with characteristics based on the Santa Cruz porphyry copper deposit near Cas a Grande, AZ. Layer resistivities and thicknesses were obtained from geophysical data and geologic logs available from the site. Modeling of borehole TEM in both preleach and during leach situations was conducted. Simulating the TEM method using computer modeling proved to be encouraging since there were substantial differences between leached and nonleached responses. The modeling does not prove the effectiveness of TEM in the field, but does indicate that detection of deep lixiviant zones is theoretically possible.

Jan 1, 1992

By Agnes Y. Lee

As part of the U.S. Bureau of Mines program to improve base metal leach systems, pressure leaching of galena (PbS) concentrates in fluosilicic acid (H2SiF6) solution was investigated. Lead extraction was 93 pct when PbS was pressure leached in H2SiF6 at 95° C with 2OO-psig O2 pressure for 40 min, using ferric nitrate [Fe(N03)3] as a catalyst. The effects of several catalysts, O2 pressure, time, and acid concentration on leaching were determined. The purified leach solution was electrowon to recover high-purity Pb metal. The H2SiF6 used in leaching and electrowinning can be recycled continuously. A flow diagram was proposed based on this investigation. Elemental sulfur (SO) was recovered from the leach residue by solvent extraction. A method was also developed for treating the flnal residue to segregate the important byproduct elements such as Ag, Cu, and Zn and enable their recovery by standard commercial processes.

Jan 1, 1990

By K. J. Liles

Research was undertaken by the Bureau of Mines to determine the technical feasibility of producing lightweight aggregate from the waste glass fraction of municipal incinerator residues. Tests were conducted to determine the amount and optimum size of glass, the amount of sodium silicate, and the method used to form the material to be expanded. The most suitable mixture, 78 percent glass, 20 percent clay, and 2 percent sodium silicate, was pelletized and then expanded by exposure to a temperature of 1,550° F for 15 minutes The resulting lightweight material had a bulk density of 38 lb/cu ft and exhibited excellent pore structure. Concrete test cylinders made from the light weight aggregate had a unit weight of 104 lb/cu ft and a compressive strength of 2,550 lb/sq in after a 28-day steam cure.

Jan 1, 1976

By J. C. Gerdeen

This project was a supporting effort with research contract H0230016 at White Pine Copper Company. Creep properties of White Pine rock were determined. These and properties for bolted joints were used in finite element analyses of sections of the White Pine Mine which included analysis of bed separations in the roof and sloping faults. In-situ experimental measurements were made of tension, compression, and bending of resin bolts by use of strain-gaged bolts. Evaluations of bolting effectiveness and comparisons of predicted and measured roof behavior are given.

Jan 1, 1976

By Jon C. Volkwein

In This Chapter [Instruments for measuring dust How to calculate the amount of dust from a source How to get a valid concentration measurement Sampling to assess control technology effectiveness] When there is more than one source of dust, sampling may be required to find which dust sources are most significant. Then, efforts to reduce dust can be concentrated where they will have the most impact. This chapter explains how to perform dust source sampling. It describes two kinds of instruments that are available and discusses their limitations. It explains how environmental variables such as concentration gradients, dust dilution, and production changes can impact dust measurements. It also suggests practical ways to improve the validity of dust source measurements under adverse conditions, such as high-velocity airflow or the presence of water mist in the air. [Dust source sampling at coal mine longwalls and at tunnels is more complicated. Chapters 3 and 7 have more information on sampling in those circumstances.] TWO KINDS OF INSTRUMENTS FOR MEASURING DUST Gravimetric samplers. The conventional gravimetric sampler is a good device for measuring dust because it is the instrument used for compliance measurements. This dust sampler consists of an air pump, a small cyclone that separates out the respirable size fraction of the dust cloud, and a filter to collect the respirable dust. In coal mines, the Mine Safety and Health Administration (MSHA)-approved gravimetric sampler uses a 10-mm Dorr-Oliver cyclone operating at an airflow of 2.0 L/min [30 CFR78 74 (2002)]. A correction factor of 1.38 is applied to make the results consistent with the U.K. MRE sampler, the instrument on which the 2.0 mg/m3 coal dust standard is based.

Jan 6, 2003

By C. W. Morris

This Final Report describes the major technical activities that were accomplished to produce a comprehensive continuous miner training system (CMTS) for coal industry utilization. The primary product of this program was a continuous miner part-task trainer. It is composed of an interactive computer graphics system combined with the operating controls of a continuous mining machine mounted in a simulated cab. The cab contains an audio system for reproducing continuous miner operational sounds. The trainer is supplemented with a complete set of cognitive materials that provide instruction in the operation, safety and health of continuous miner operations. A complete summary of the field test and evaluation of the CMTS is provided along with a set of recommendations for further training program refinements, expansions, and utilization.

Jan 1, 1982

By T. L. Muldoon

The bagging of dry pulverized products using fluidized air packers creates severe respirable dust problems in many surface mining operations. During bag filling, excess air and product blows by the bag valve/nozzle interface. After bag ejection, dust blows out of the bag valve. During conveying and handling dust is released from the bag valve and dirty bag surface. Overexposure of the bagging machine operator and bag handlers is common. This report describes the development and testing of a new dust control system for bagging machines. The system features a new bag clamp design to reduce product blowby during filling. A controlled vacuum system removes excess air from the bag before ejection, eliminating the problems after bag ejection and during conveying and handling. The system has shown significant reductions in dust exposure for both bag machine operators and bag handlers. These reductions are achieved with no significant effect on total mill productivity.

Jan 1, 1985

By William R. Barton

Dimension stones, with their almost infinite variety, have a broad range of properties and uses. Natural stone was beyond doubt the first mineral commodity used by man. Today dimension stone has widened to encompass building exteriors and interiors, decorative and ornamental modes, statuary, monuments, paving, curbing, flagging, roofing, and miscellaneous categories such as blackboards, surface plates, and honestones. For many purposes, it competes with greater or less success with alternate materials such as concrete, metal, brick, plastic, or glass. The almost ubiquitous geographic distribution of stone resources is the basis for a dimension stone producer industry in almost every State and in almost every land. In the United States, alone, dimension stone sold or used by quarries is valued at 2 million to 3 million dollars annually. Mining, finishing, transportation, and use technology have been modernized, resulting in a broader spectrum of stone products and new adaptions in use. Increased efficiencies also have been reflected in costs and prices and, coupled with gains that should be realized from current research, auger well for continued vitality of the ancient and honorable dimension stone craft.

Jan 1, 1968

By M. Kanda

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in and above an operating coal mine, McElroy Mine, located near Moundsville, West Virginia. The electromagnetic environment created by 300 volt dc and 480 volt ac machinery was measured. In one technique noise was measured over the entire electromagnetic spectrum of interest for brief time periods. The noise was recorded using broadband analog magnetic tape. The noise data was later transformed to give spectral plots. In the other technique, noise amplitudes were recorded at several discrete frequencies for a sufficient length of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 1, 1974

The objective of this condensed handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface coal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. It will be carried with the inspectors during their surveys. The complete handbook should be left in their offices except for Appendix II which lists the compositions of products found in previous surveys. There are several portions of the condensed handbook which should prove most useful to the inspectors. The names and locations of these portions are listed below: Procedure for an Industrial Hygiene Survey (Page 2-1) Survey Check List (Page 2-3) Rules for Determining if Sampling is Required (Page 2-2) List of Most Frequently Encountered Contaminants (Page 2-5) List of Candidate Contaminants and their Sampling Conditions (Page 2-A) Interpretation of Results (Page 3-8) For obtaining information not available from the above mentioned portions of the handbook, the inspector is directed to the Table of Contents, and the Glossary of Terms (Appendix I).

Jan 1, 1975

By J. Bennetts

As part of its mission to develop technology that will help increase the supply of critical and strategic minerals from domestic resources, the Bureau of Mines has investigated methods for beneficiating platinum-group metal ores from the Stillwater complex, Montana. This report presents the result of a bench-scale study employing froth flotation to recover a sulfide concentrate containing platinum-palladium values from a mineralized gabbro. Best results were obtained with a flotation scheme utilizing a mercaptobenzothiazone collector and sulfuric acid. Rougher concentrates containing approximately 11 oz Pt-Pd/ton and 90 pct of the metal values in the ore were obtained. Subsequently, cleaner concentrates containing approximately 26 oz Pt-Pd/ton and between 80 to 85 pct of the Pt-Pd values in the ore were prepared.

Jan 1, 1980

By John J. S. Sebastian

A laboratory-scale investigation was made of the basic problems involved in developing a ceramic heat exchanger to operate at high temperatures for using nuclear heat from gas-cooled process-heat reactors. Technical data were obtained on transferring heat by forced-convection from helium to air in a single-tube vitreous-alumina heat exchanger. Coolant air was passed through the annulus parallel with, and either concurrently or counter to, the flow of helium inside the tube. The data obtained pertain to removing heat from the helium. Average inside film coefficients were determined at mean surface temperatures of 200° to 1,570° F., inlet-gas temperatures of 1,450° to 2,665° F., and Reynolds numbers up to 560. The gas-to-surface temperature ratios were varied from 1.05 to 7.6. The tabulated results are shown in the appendix at the end of this report. The film coefficients of heat transfer were correlated by taking into account the physical properties of the helium at the average fluid temperature. With experimental conditions pointing to a laminar flow, the Nusselt number was found to decrease as the ratio of gas-to-wall temperature was increased to a value of 3. However, within the range tested, gas-to-wall temperature ratios above 3 did not affect the Nusselt number, regardless of the value of the Graetz number. Thus, beyond this point any increase in this ratio ceased to influence the heat-transfer relationship.

Jan 1, 1962

By C. Lurie

This final report describes the work performed by Gulton Battery Corporation under USBM Contract No. HO-112033, entitled "Research and Development on Lithium-Nickel Fluoride Batteries For Mint Life Support Equipment". The lithium-nickel fluoride couple was chosen For this investigation because of its high theoretical energy density (626 Wh/lb), its ability to operate at ambient temperatures and the fact that it showed promise as a secondary system. The theoretical energy density of the lithium-nickel fluoride couple is ten times greater than that of the widely used lead-acid battery and three times greater than the silver-zinc battery which has the highest theoretical energy density of the commercially available secondary systems. The experimental program first evaluated the cell components individually. The results of these studies then formed the basis for investigations of cell performance using experimental three-plate cells. These cells consisted of one nickel-fluoride and two lithium electrodes. All work was performed in a glove box under an argon atmosphere which was sufficiently pure to maintain the shiny appearance on freshly prepared lithium surfaces. The major portion of the work effort was concerned with the nickel fluoride electrode. Binder, conductive diluent, fabrication technique, as well as the nickel fluoride active material itself, were considered. Criteria for binder materials were established and six classes of materials encompassing thirteen binders were evaluated. The candidate materials were initially screened for appropriate chemical and physical properties and finally evaluated in three.-plate cells, Two epoxy powders emerged as the most promising binders. Two types of conductive diluent were evaluated. The first is a carbon black of low bulk density and high surface area. This material is a good conductive diluent; however, electrodes fabricated with it lacked good mechanical strength. It was hypothesized that a uni¬form, small particle size, low specific surface area would improve the mechanical properties of the electrodes. Therefore, two samples of graphicic materials, milled to uniform powders in the one-to-ten micron range were evaluated. Electrodes prepared with the graphitic materials had superior mechanical properties, However, their electrical performance was significantly poorer and voltage losses of 0.2 to 0.3 volts were observed. Several electrolyte solutions were evaluated. N-Methyl-2-Pyrrolidone was tested but found to be incompatible in the presence of lithium. Lithium perchlorate, lithium hexafluoroarsenate, and lithium bromide were tested as two-component electrolytes in propylene carbonate solvent and their performance compared with that of the single electrolyte solutions, Lithium perchlorate gave the best performance. Lithium hexafluoroarsenate was also evaluated in methyl formate and appears to give equivalent performance. The lithium perchlorate-propylene carbonate system is preferred as it is easier to handle and less expensive.

Jan 1, 1973

By David A. Summers

The use of high pressure fluid cavitation is investigated as a means of breaking an ore into its constituent grains. This Cavitational Rock Dissagregation (CRD) is found to be possible and effective in breaking down galena ore, both in sandstone and dolomite host material. The technique did not work as well in comminuting and cleaning oil shale, because the cavitation drove the oil into emulsion with the water. The presence of dominant bedding in the rock also caused preferential breakage to these lines, rather than to the individual grain boundaries. This problem was also encountered in tests on igneous ore where weakness plants of the overall ore proved weaker than the boundaries of the individual grains. It was found that the prevailing expression of cavitation erosion dependence on pressure was not absolutely valid. In contrast it was found that CRD is much more sensitive to jet flow diameter, and when this was recognized it was found possible to erode rock with compressive strength of up to 350 MPa with operating jet pressures of 10 MPa.

Jan 1, 1982

By Stephen D. Smith

The following tables summarize data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in these tables is what is termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines. Because of inadequacies in the statistics available, some series deviate from the foregoing definition. For copper, gold, lead, silver, tin, and zinc, the quantities are recorded on a mine basis (as the recoverable content of ore sold or treated). However, the values assigned to these quantities are based on the average selling price of refined metal, not the mine value. Mercury is measured as recovered metal and valued at the average New York price for the metal. The values shown are in current dollars, with no adjustments made to compensate for changes in the purchasing power of the dollar.

Jan 1, 1995

By C. C. Anderson

"While conducting investigations in connection with the helium program of the Bureau of Mines, the Cryogenic Laboratory has improved an apparatus for the rapid and accurate determination of the helium content of natural gas and gaseous mixtures derived from that source. The separation of helium is effected by the use of activated coconut charcoal which, when cooled to liquid-air temperatures, absorbs the nitrogen and other constituents of the gas, leaving the helium in a. spectroscopically pure state. This absorptive property of activated charcoal was discovered- by Dewar3/ in 1875. Several years later, while conducting their original researches on helium in natural gas, Cady and McFarland employed the charcoal method for the absorption and removal of the common constituents of natural gas and constructed an efficient apparatus in which this operation could be effected.4/ Shortly after initiating the government's helium activities during the World War period, the Bureau of Mines adopted, with Minor modifications, the Cady and McFarland apparatus and method of analysis. Seibel.5./ described this modified apparatus and method of procedure as part of a publication on helium-bearing natural gas. Subsequently, the Bureau's apparatus for helium analysis has been simplified and improved to facilitate more rapid and positive operation. The apparatus and method of procedure now being used by the Bureau of Mines Cryogenic Laboratory arc described in this paper.The personnel of the Bureau of Mines Cryogenic Laboratory has improved and brought the helium apparatus described herein to its present state of perfection. The writer's contributions have been-of minor importance, and he wishes to give the various members and former members of the laboratory staff full credit for the improvements they have made. He also desires to express his appreciation for suggestions and criticisms offered during the preparation of this paper to the following members of the Petroleum and Natural Gas Division, Bureau of Mines, which now includes the Amarillo Helium Plant and Cryogenic Laboratory: H. A. Cattell, chief engineer; C. W. Seibel, supervising engineer of the Amarillo Helium Plant; W. M. Deaton, chemist-in-charge of the Cryogenic Laboratory; and H. S. Kennedy.The quantitative determination of helium in a gaseous mixture is accomplished by the removal of the other constituents from the sample, either by chemical or physical Means, leaving only the helium which can be measured directly. Chemical methods, when applied to natural gas, require the burning of the hydrocarbons in oxygen, the, absorption of the resulting carbon dioxide in a caustic solution, the removal of the excess oxygen in a suitable solution such as an alkaline pyrogallate, and the elimination of nitrogen by sparking or by combination with hot calcium or magnesium.. Such procedures are very slow and tedious compared with the physical method which employs the absorptive property of activated charcoal to effect the separation of the other constituents from the helium."

Jun 1, 1934

By Steven W. Schmauch

A mineral survey by the U.S. Bureau of Mines and U.S. Geological Survey indicate the Blanco Mountain RARE II area has low potential. Lode deposits consist of small, mineralized quartz or quartz-gossan veins. The veins are sparse and widely separated and lead, silver and gold content is restricted in amount and concentration. No gold or other potentially economic minerals were found in a placer deposit. There is no evidence of industrial mineral, geothermal, or energy resource potential in the study area. INTRODUCTION A mineral resource survey of the Blanco Mountain RARE II area (No. 5059), Inyo and Mono Counties, California was conducted in July 1981. This report summarizes the results and interpretations of the Bureau of Mines investigation.

Jan 1, 1982