Search Documents

By T. G. Sitharam, P. B. Choudhury

Prediction of ground vibration (peak particle velocity, PPV) and frequency is an important task in geoscience. Till date, many empirical equations are derived from conducting trial blasts in the mines, to arrive at attenuation predictors. These predictors are usually site dependant and hold good for one particular type of rock/strata. These predictors cannot be used for geologically different rocks/strata. This paper presents the application of support vector machine (SVM) model, for predicting blast induced ground vibration and frequency, using a one comprehensive model for three different types of rock. Inputs to the SVM model formulation involve twenty one parameters consisting of geotechnical properties of the rock mass, blast design geometry and explosive properties, and the output of the formulated model is peak particle velocity and its associated frequency. The data has been acquired from eight limestone mine, five coal mine and two manganese mines. The comprehensive SVM model is formulated using 400 datasets and tested with 143 datasets. The performance indicators to the model not only justify its formulation but also the advantages it has over site specific predictor models. The SVM model not only predicts PPV, with higher correlation coefficients as compared to predictor equations, but also the associated frequency.

Jan 1, 2010

By Chris Breeds, Larry Leone, Jerry Wallace

One of the Authors was recently retained to provide a professional engineering analysis of the potential impacts from underwater blasts used to enlarge intake tunnels at the Cheesman Dam near Denver in Colorado and to design Blast Protection Bags that could be installed in each tunnel to protect the 100- year old downstream valve structures.

Jan 1, 2012

By Charles E. Van Barneveld

RBH Note: the following item is a little different than the usual, in that it shows how explosives were used in the past to assist in putting down holes for iron ore prospecting on the early Mesabi Range of Minnesota. The way explosives were used would not even occur to the modern explorationist, given the equipment available today. The reason for the great difficulty in putting down a hole was that the area was covered with debris from the great glaciers of the past (the same ones that carved out the Great lakes). This debris consisted of boulders, clay, sand, and any other imaginable mixture of materials.

Jan 1, 2013

By David Nemir, Jan Beck

A challenge in materials science is the production of a bulk solid material from a powder precursor. One solution is to use shockwave consolidation whereby a ductile tube is loaded with the powder of interest and then surrounded by an explosive. A detonator at the top of the explosive column initiates a symmetrical high-pressure pulse that moves inward and down the tube, causing the tube to deform and the interior powders to consolidate into a dense, well bonded bulk material.

Jan 1, 2016

By Gerald R. Coonan

I'm really here to talk about my pet subject of government relations. I've been in Peabody's Environmental Quality Department, working on regulations, for over five years, and I have seen a number of individuals in the coal industry who were completely stunned when a new regulation was brought to their attention. Their first reaction was, "where did this come from"?

Jan 1, 1980

By Bill Loviza, Jimmy Sanders

This report is not everything we would like it to be. Access to information concerning unresolved legal actions is a sensitive matter. Obtaining the information presented in this report was a challenge alone. The Tennessee Department of Commerce and Insurance, Division of Fire Prevention, the firms and individuals that elected to share information did so with various assurances of nondisclosure, confidentiality or anonymity. All those providing information did so with the expectation that the industry and ultimately the public would benefit from this effort. We offer special thanks to Assistant Commissioner, Fire Prevention, Emmett Turner, recently retired Director, Bomb and Arson, Dick Gardner and Director, Codes Enforcement, Randy Safer for support that made this endeavor possible. We make no claim with regard to being a scientific study. We did the best we could with available information. Our task was one of assembly, sorting and reporting. Where collateral information was available we used it.

Jan 1, 2004

By Scott G. Giltner, Terry Millar, Ben Bringhurst

"Kennecott Utah Copper (KUC) Smelter scheduled a rebuild of their flash smelting furnace forSeptember, 2014. KUC’s goal in this project was to reduce the rebuild time from 65 to 55 days by using explosives to break the matte and brick layers of the uptake shaft and hearth sections of the furnace. Previous rebuilds had employed the slower technique of mechanical breakers to remove the matte and brick layers which took 22 days. KUC has many years of experience in removing slag from the uptake shaft, but they had never used explosives to remove the hearth. As far as KUC was aware, no other smelter operation had attempted a hearth removal in this way."

Jan 1, 2016

By Leslie Taylor, W. L. Fourney, Uli Leiste

Over the past few years, our laboratory has been investigating the loading on vehicles due to the detonation of buried explosives. We have been using target plates to represent the bottom of the vehicles that were being subject to the forces from the detonating explosives. Parameters shown to be important in the blast loading were type of soil, stand off distance (distance from the surface of the soil to the bottom of the target plate), and depth of burial (distance of the charge center of gravity to the sand surface). We conducted over the first year of our work a large number of tests which looked at the impulse being applied to the plates as a function of depth of burial, stand off distance, and type of soil. Of the three parameters we found stand off distance to be most important, depth of burial to be the next most important parameter, with type of soil least important. We also found that impulse could be scaled with explosive size quite accurately and that results (for impulse) were quite repeatable from one test to the next.

Jan 1, 2008

By C. Kosloski, E. McCullough, A. Fox, S. Reed

This paper serves as a reference guide for creating or strengthening student chapters of the International Society of Explosives Engineers. This includes chapters that are just starting, currently undergoing transition in leadership, or that are in the process of rebuilding. ISEE student chapters have great potential to increase student involvement and national membership, and can benefit from formalized strategies to help them do so. Several key strategies are introduced and should be employed to promote organizational participation throughout the university system.

Jan 1, 2016

By Alejandro Rosario, Ricardo Dumuihual, Guillermo Silva, be nito Danial Valde, Carlos Scherpenisse

A monitoring campaign to record dynamic pressures generated by detonation of a single blasthole was implemented at Barrick Gold´s Pueblo Viejo Open Pit mine (PVDC), located in the Dominican Republic. Pressure amplitudes beyond the dynamic compressive strength of the electronic detonator´s capsules have the potential to damage these electronic devices, generating misfires along with all the associated risks and entailed safety implications. In most instances, misfires generated from high dynamic pressures are a direct consequence of drilling deviations resulting in blasthole distances smaller than originally designed. Tourmaline Crystal Sensors specifically designed for high dynamic pressure measurements in aqueous media were selected to address the challenge. These sensors are custom-made and require additional instrumentation for proper operation, including signal conditioners and recording equipment capable of capturing simultaneous events, both in their amplitude and frequency components. Field-testing comprised detonation of a single blasthole using current explosive loading practices along with an arrangement of sensors positioned within water-filled drillholes in a spiral configuration. Distances, explosive weights and all 23 dynamic pressure record amplitudes are included along with additional data regarding arrival time and P-Wave velocity estimations. As with typical vibration models, the Scaled Distance concept (D/W1/2) was used to construct an attenuation model relating Dynamic Pressure as a function of Distance (D) and explosive Weight (W). The resulting model, adjusted to a 95% statistical confidence limit (covering 100% of the recorded data) was used to generate a series of curves (Abacus) estimating dynamic pressure as a function of distance for different explosive charges. These curves, in association with permissible pressure limits defined at 50% (FOS = 2) of the dynamic pressure strength reported by manufacturers for both, the 1000bar (Al) and the 1400bar (Cu) capsules; allow for the determination of critical (safe) distances between blastholes. Tests were implemented to cover a variety of field scenarios, accounting for different rock mass types, qualities and water conditions; however, preliminary analysis indicate the convenience of developing a unique trend that considers said variability. This approach allowed construction of a single, simple, unambiguous and operationally applicable design tool to address entailed safety issues.

By M. Szumny, P. Mertuszka, K. Fuławka

Mining-induced seismicity is one of the adverse side effects of mining with the use of explosives at great depths. Disturbance of the primary stress state by the development of the network of excavations combined with the continuous generation of dynamic loads by the detonation of explosives in mining faces has a negative impact on the level of safety of crew and machines. To ensure the stability of excavations it is necessary to identify in detail the nature of the seismic hazard by means of continuous seismic measurements. Unfortunately, the technologies used so far are characterized by high costs of installation and further maintenance, which clearly limits the possibility of using a large number of stations in a small area. A breakthrough in this matter may be the technology of microelectromechanical systems, which is several times cheaper than standard solutions used in mining seismology. This technology, with the appropriate configuration of devices, can be successfully used to monitor dynamic phenomena generated by mining activities. As part of this study, the assumptions and configurations of a prototype 42-channel accelerometer network using MEMS technology have been presented. The network was installed in the Lubin underground copper mine in Poland in a seismically active area, where multi-face destress blasting are conducted regularly. As a result, 14 tri-axial accelerometers were installed in the immediate vicinity of the active mining front at a distance of about 1,000–4,000 ft (300–1,200 meters) from the closest faces. Highfrequency recordings are collected based on algorithms that trigger the system when the Peak Particle Acceleration set value is exceeded or on the basis of a manual external triggering device connected to the blasting machine. During the measurement period, several high-energy seismic tremors and several dozen of waveforms generated by blasting were recorded. The obtained results are the basis for assessing the effectiveness of the destressing measures and for the analysis of geomechanical risk based on periodic analysis of the velocity of seismic wave propagation

Jan 1, 2024

By Rob Farnfield, Ben Williams

The A5 road in the United Kingdom forms an ancient and well-used route through the hills and mountains of North Wales. In the 1990?s a programme of work was conducted to upgrade the road to modern standards. As part of this work a new cutting was constructed to bypass a portion of road routed through a gorge close to the village of Ty Nant. This new cutting was formed by drilling and blasting and included much pre-splitting and extensive rock bolting. This operation caused much concern to local residents relating to vibration, air overpressure and flyrock.

Jan 1, 2011

By Hernan Navea, Carlos Alvarado, Exequiel Nuñez, Matías Suarez, Jhon Silva, Bryan Townsend, Bryan Caceres, Felipe Pontanilla

Nowadays, technology dominates all aspects of human activities, and drilling and Blasting (D&B) is no exception. In most cases, the use of technology in D&B is focused on controlling individual activities such as drill performance, drilling advance rates, truck loading performance, etc. Still, in very few instances, the advantages of using technology along each D&B activity and how this influences the D&B results are documented. This paper shows how technology is applied to create a “relative hardness” model for the mine Caserones in Chile. In the future, the model can relate the relative hardness parameter to several variables, including excavation rate, fragmentation results, and vibrations. It can also be used in the explosives loading process, similar to the model used by Dyno Nobel’s Differential Energy (DE) technology. In the relative hardness model for Caserones, a design is loaded in the drill system, and data is collected during the advance of the blasthole. The collected data includes rpm, torque, pressure, etc. Then, an algorithm using the measured variables while drilling and known relationships between the properties of the rock and the drill's performance is used to classify the average relative hardness of the blasthole in four intervals: hard, medium, soft, and very soft. Optimization techniques and models used in the oil and gas industries to analyze drilling performance were adapted to implement the algorithm. The model uses the concept of mechanical specific energy (MSE). Using the data from the drill, the algorithm identifies the depth where the MSE reaches a minimum to calculate the “relative hardness” for the blasthole under analysis. The results are presented in maps highlighting the areas where hard, medium, soft or very soft rock masses are expected. That information can be used to anticipate areas where explosives with higher energy need to be used or to predict areas of the blast with additional digging difficulties and then lower loading rates. The paper shows examples where “relative hardness” maps are compared to drilling speed excavation rates and other variables.

Jan 21, 2025

By Ravi Sahu, Brad Gyngell, Oktai Radzhabov

Design machine learning approach to simulate the process of muckpile throw distribution before blasting.

Feb 1, 2020

By Cristian Castro, Patricio Gomez, Jason Furtney, Augusto Lucarelli

Understanding the effect of blast-induced damage on wall stability is critical to safe and economical operation of a large open pit mine. In this paper, a numerical modeling methodology is used to investigate damage to rock at distances of greater than 10 m (30 ft) from a blast. Two applications of the model are demonstrated. First, the method is applied at a zinc mine to investigate the effects of pit blasting on underground stopes. The model predictions are compared with the scaled distance formula. Next, the model is used to investigate a common problem in which unfavorable jointing creates a rock wedge on the bench above a blast. The numerical predictions of wedge stability are compared to the wedge energy model described by Wong & Pang (1992).

By Cristian Castro, Patricio Gomez, Jason Furtney, Augusto Lucarelli

Understanding the effect of blast-induced damage on wall stability is critical to safe and economical operation of a large open pit mine. In this paper, a numerical modeling methodology is used to investigate damage to rock at distances of greater than 10 m (30 ft) from a blast. Two applications of the model are demonstrated. First, the method is applied at a zinc mine to investigate the effects of pit blasting on underground stopes. The model predictions are compared with the scaled distance formula. Next, the model is used to investigate a common problem in which unfavorable jointing creates a rock wedge on the bench above a blast. The numerical predictions of wedge stability are compared to the wedge energy model described by Wong & Pang (1992).

Feb 1, 2020

Existing geological structures such as faults or shear zones can greatly influence the interpretations of amplitude or energy attenuations of measured blasting vibrations along both affected and unaffected orientations. Mineralisation in conjunction with large faults or shears is commonplace in the geology of steeply dipping metalliferous deposits, such as those found in the goldfields of Western Australia. Better understanding of the influence of faults or shear zones on blast-induced seismic waves can lead to more effective blast vibration monitoring programs and interpretation of the results measured along affected orientations.

Jan 1, 2011

By Christian Dye

"The following paper focuses on the developing relationship between the members of theInternational Society of Explosive Engineers (ISEE), and the mining students from the BritishColumbia Institute of Technology (BCIT). During the past two years mining students and theISEE members have worked closely in developing a student chapter within the society and onFebruary 1st 2015, the first Canadian Student Chapter was recognized at the annual generalmeeting in New Orleans. This paper discusses the benefits that both the industry and studentsgain with a strong relationship. The mining students recognize the importance for filling the rolesof retiring members of the society and industry. Prior to 2015 the school had only offered a twoyear diploma program in mining and mineral exploration methods. That included a brief sectionin the use of explosives in the mining industry. In September of 2015 students were recruited forthe first ever Bachelors in Mining and Mineral Resource Engineering program. This engineeringdegree includes a full four month course in advanced blasting and rock fragmentation. Studentssuccessfully completing the diploma program will have an entry level of technical understandingin how blasting is conducted. The students successfully completing the bachelor degree will havean in depth technical understanding of explosives and rock fragmentation. Having this uniqueand dynamic multi-level program provides the explosives industry with a pool of talent that canbe used to fill positions with graduates for all levels of the blasting industry."

Jan 1, 2016

By Quentin L. Rhoton

"The use of explosives in a surgical manner was approved to facilitate, due to time constraints, anextremely significant paleontological find in the Plunket Point area of the Dominion Range, Antarctica. The organic material revealed by surgical blasting techniques may have altered basic scientific dogma on Antarctic glaciation theory."

Jan 1, 1999

By Lizbeth A. Escobar, Phol M. Llanos, Maritza Y. Avila

The present research develops the estimation of critical parameters such as the distances and times between holes to avoid failure due to dynamic pressure in electronic detonators based on the near-field ground vibration model of Holmberg & Persson and the hydrodynamic model of Neyman.

Feb 1, 2020