Search Documents

By Ruilin Yang

"Blast vibrations are essentially a strain/stress wave propagating in rock or structures inthe vicinity of a blast. However, blast vibration has always been quantified in terms ofpeak particle velocity (PPV) or acceleration (PPA), and a meaningful relationshipbetween blast vibration and strain/stress has not been established. The determination ofthe dynamic strain from blast vibration may improve quantification of blast damage andselection of a blast vibration limit for critical structures or high walls. Dynamic strainrelates to rock mechanics or material strength more directly than peak particle velocity(PPV). This paper documents a method to calculate the three-dimensional dynamic straintensor from recorded blast vibration signals. The method is based on determination of thedisplacement gradient at a point of interest for each time instance during the vibrationduration. The method to calculate dynamic strain is applicable to generic seismicwaveforms including near and far field blast vibration from a production blast withmultiple blast holes. In order to minimize measurement errors the specifications of thespacing between monitors and the sampling frequency of the vibration recording aredescribed."

Jan 1, 2012

By D T. Froedge

With successive generations of the Iso-Seismic System, we are acquiring more and more information about the actual behavior of blast induced ground, and airborne vibration, as it propagates through the environment. Some of the original “truths” that have been long accepted may have to be \revised.

Jan 1, 1995

By Roland Oliver

Detonators or blasting caps are made in several different grades of strength, because some powders require not only a greater, but a different initial detonation than others to convey their maximum energy through a whole charge, and the detonating qualities of each powder vary with changes in its physical condition––whether it be warm or cold, rigid, plastic, homogenous or otherwise.

Jan 1, 2007

By Noel Dent

The Electrodet@ Electronic Detonation System Wilere are we going with regard to Accurate, Reliable, Easy to Use and Cost Effective Initiation using electronic initiation techniques? Improvements and applications in theJierd

Jan 1, 1995

By Darcey Baker

Quarry Blasting is usually boring, and that is how we like it. By this, boring means routine, straightforward, meat and potatoes blasting. Quarries typically will not utilize cast blasting, coyote tunnels, or any of the other more spectacular blasting techniques – just plain, old day-in and day-out quarry production and possibly overburden blasting. Differences in material characteristics, mining method, equipment availability, and target markets all play a part in determining the blasting procedures employed at any given location. However, variables exist everywhere and with foresight and planning, effects of tangible variables can be minimized. Variables caused by geology, weather, neighbors, or limitations caused by major plant or mobile equipment are, generally speaking, intangible; and leave the operator with finite options to improve or modify blasting procedures.

Jan 1, 2009

By C. T. Aimone-Martin, B. M. Meins

This paper compares response of large urban structures to small charge weight, ultra-high frequency rock blast excitation from contiguous excavation to that of houses to more distant, larger charge weight blasts. Time correlated responses were measured for both structures at the corners, top and bottom of the structures as well as in the foundation rock below the bottom. The comparison allowed the following conclusions: Close-in blasting with direct rock to building wave transmission imposes short wave length excitation which fails to excite the large, massive structures synchronously whereas the more distant blasts do synchronously excite houses. The larger urban structures respond predominantly in wave transmission mode where there is a noticeable difference in time, frequency, phase and amplitude of motions measured at the bottom and top corners of the structure. Excitation motions along the base of the larger urban structures also differs in time, frequency, phase and ampli-tude. The short wave length of the excitation motions leads to attenuation of the peak particle veloc-ity along the base. Ultra-high excitation frequencies, which are much higher than the expected struc-tural natural frequencies, lead to deamplification for all events for the large urban structures.

Jan 1, 2018

By V. Petr, G. G. W. Mustoe, T. G. Rozgonyi

We introduced a numerical method that is applicable for the analysis of static and dynamic deformations of elastic media. In this numerical study, each elastic body is modeled with a system of several hundred rigid particles that are joined together elastically. Maximum shear stress fields due to external loading are obtained and compared with those obtained by photoelastic experiment. Preliminary results are presented for the stresses generated in circular disk shaped bodies idealized with connected systems of particles. Extension of this simulation method to fragmentation of brittle materials is also illustrated in an example.

Jan 1, 2000

By Johan Finsteen Gjodvad, Mathias Jern

The paper is part of the ongoing work of the Environmental committee of EFEE. To assist the European experts working with explosives one of the aims is to improve the common knowledge of similarities and differences between national legislation, standards or guidelines on vibration monitoring and other environmental monitoring during blasting in Europe and abroad.

Feb 1, 2020

By David Siskind

The authors studied small seismic exploration blasts for vibration characteristics and effects on structures in Mexico. Obtained were 267 three-component recordings of ground vibrations and structure responses from 62 test blasts at six single-story masonry structures. Charges were 4.55 kg (10 lb) of Vibrogel expolsive at depths of 20 and 30 meters. Initial blasts were 240 meters distant and proceeded towards the structures to as close as 5 meters. All blasts were in soil media in two basic types of terrain, low saturated areas and upland dry areas. Structural inspections were before, during, and after the test blasts.

Jan 1, 2002

By John Vynne

Too often, a mine’s operations, including drilling, blasting, loading, hauling, crushing, processing, etc., are considered independent steps, rather then a continuous process. In fact, these are interdependent operations with each step in the process having an impact on subsequent operations. If the effectiveness of the drilling and blasting operations can be improved, they will impact the entire mining process. Some of the resulting improvements include: level benches on grade; fragmentation and diggability with the result being reduced loading times; haul cycles improvements; and the crushing and milling operations will be more efficient and less energy consumed. Thunderbird refers to this as “Drill to Mill” information cycle or process. This paper focuses on two of the technological enhancements Thunderbird has added to its drill monitors that allow the mines to impact the “Drill to Mill” concept. These enhancements are: incorporating global positioning satellites into drill monitors; and radio off-loading of data.

Jan 1, 2001

By Felix Torres

CVRD is one of the largest mining companies in the world. Adoption of new technology and improving operational efficiency are top company priorities. Initiatives in these areas have driven continuous company growth and an increased share price. During the first half of 2001, the company had a net profit of nearly US$ 500 M.

Jan 1, 2003

The objective of current efforts by AQUILA Mining Systems Ltd. is the continued development of computer-based systems and techniques to automatically process and interpret monitored performance data from surface blasthole drills and mining shovels, and the management and coordination of these pieces of equipment by GPS (Global Positioning Systems).

Jan 1, 1995

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By Cceliksirt, V Erkan

This computer program has been developed under the field conditions for use in control of surface drilling-blasting operations. This paper outlines the relevance of fragmentation to quarrying, open pit mining or road cutting and key features and operating principles of the software (DelPat for Windows 95).

Jan 1, 1998

By Robert Hopler

In the annual report under the Explosives Act for 1905, H.M.inspectors state that over 90 percent of the accidents causing death or personal injury occurred in the use of explosives and under miscellaneous conditions to which the controlling provisions of the Act do not apply, and that such accidents caused 43 out of the 50 deaths, and 312 out of 348 cases of injury. The number of accidents grouped under the heading of “Use and Miscellaneous” is less than that for 1904 - viz., 281 against 301. By these accidents 43 persons were killed and 312 injured, as compared with 39 killed and 343 injured in 1904

Jan 1, 2007

By B Brown, P J. Hommert, B J. Thorne

"Early attempts at estimation of stress wave damage in blasting by use of finite element analysis met with limited success due to numerical instabilities that prevented calculations from being carried to late times. A"" improved damage model based on microcrack growth in tension allows finite elementcalculations which remain stable at late times. Estimation of crater profiles for blasting experiments in granite demonstrate successful simulations with this model."

Jan 1, 1990

By Geraldine Woods

I work for the State of Washington as an Explosives inspector. My paper will describe the mission of the Wa. State Dept. of Labor pertaining to explosives and the regulation of explosives in the State.Blasting safety is high on the public safety list and the regulation of explosive use and storage has been mandated through legislature. The Dept. considers pro-active partnering forexplosive safety preferable to after-the-fact citations for non-compliance.In some cases, the Dept. will issue civil citations with monetary penalties, meant to be a deterrant, of course, to blasters who choose not to comply with the explosive regulations of the State.The Dept. has also revoked and suspended blasting licenses. In some instances, the Dept. has allowed recipients of citations with monetary penalties to reduce the amount paid by attending technical training classes. The idea here, is to reduce the chance of reoccurence of unsafe blasting practices. The State of Washington partners with MSHA in the regulation of explosives use and storage in mines, pits and quarries in the Stateas well as working closely with law enforcement, State and local fire marshals, ATF,and is active in ISEE in part of it’s ongoing effort to promote explosive safety and establish communications in a nonadversarial way with explosives users. My paper will include some statistics on licensing in the State, pounds of explosives used, inspection numbers, numbers and types of complaints with information from the inspections resulting of these complaints. My paper will include examples of storage, both good and bad, examples and pictures of fly rock incidents, accidents, near-miss close calls, break-ins, thefts, and abandoned explosives. This paper may also include a brief summary of my opinion of explosive regulation and my job as a regulator, including examples of high and low points of the job, joys and frustrations.

Jan 1, 2002

By Maurice Hunter

The paper outlines recent design developments in the computerization of surface crawler drills for the quarry industry. It references the technology firstly developed for the underground mining and construction industry, where automation and computerization has been in demand for a number of years.

Jan 1, 2003

A simple and cost effective technique to increase fragmentation and burden velocities without making major modification to the overall blast design is with ALTERNATE VELOCITY LOADING OR BOOSTERING OF ANFO. The technique requires the placement of a cartridge or slug of explosive, having higher density and detonation velocity than ANFO, every few feet in an ANFO column. The greater the difference in density and detonation velocity of the Alternate Velocity Load to ANFO, the more pronounced are the results. Emulsions were selected as the Alternate Velocity test explosives because they detonate closer to ideal conditions than most other commercial explosives.

Jan 1, 1989

By Francisco Sena Leite, Pedro Brito, Gean Frank, PhD Soeiro de Carvalho, Jose, Vinicius Miranda

The consequences of rock blasting with explosives are directly related to the accuracy of drilling and, because they have an effect on fragmentation and ground level, they should be controlled to ensure a problem free production, increase work safety and reduce environment impact. Safety control is one of the most important processes in detonation, since it can compromise the worker security on site and, eventually, neighboring communities. Due to the technology advancements, it is possible to build a hole deviation control device with “of the shelf” parts, and for that reason the authors decided to evaluate the possibility of measuring hole deviation by creating a portable prototype using an electronic sensor capable of measuring the acceleration on objects, that is, to measure the own acceleration of a system, known as "accelerometer" and a micro-controller to handle and treat data. The main idea behind this paper is to validate the power of the Euler method, given the stepping limitations of the sensor and micro controller in order to reproduce of the hole shape. A case study was carried out, comparing the measurements of borehole deviations made by a traditional equipment and the prototype. A mobile application was also created in order to recover and treat and display the data to the user. For validation of the prototype, several holes were measured using the two devices. A residue analysis was used to validate the data obtained. After analyzing and confirming the effectiveness of the new equipment, the normality tests prove a symmetric distribution with null expected residual mean and minimum variance. Consequently, the accuracy of the prototype is evidenced. Thus, the authors aspire to emphasize the potential of using these sensors allied to a traditional numerical method for analysis of hole deviation.

Jan 1, 2019