Search Documents

By P. Hatefi, O. Rahmani, M. Noor-Mohammadi, A. Tohry

"Depressants play an important role in the selective separation of impurities from iron minerals by direct or inverse flotation. In this paper, sodium co-silicate (SCS) with chemical formula of Na4SiCO6, as a depressant with pH modifier features, has been synthesized and used for phosphorus bearing iron ore in anionic reverse flotation. In this process, phosphorus is floated while the iron oxides are depressed, using fatty acids as collector in an alkaline medium. Batch and pilot flotation tests were carried out to investigate the influence of SCS on the separation selectivity of phosphorus from iron oxides. Also the depression mechanism of SCS on hematite surface was investigated by microflotation tests and FTIR spectroscopy measurements. The flotation results indicated that without using a pH modifier, the pH of pulp could reach up to 10, when SCS was used as depressant. In this condition, a better depression performance was observed compared to sodium silicate (SS). Using the SCS, phosphorus and total iron content in iron concentrate was 0.046% and 66.29%, respectively, compared to SS where these values were 0.06% and 65.75%, respectively. As a result the weight recovery of iron concentrate was increase by around 4%, compare to SS. It was also found that 238 g/t of SCS could be used instead of 3 types of reagents collectively, including 32 g/t of NaOH, 151 g/t of Na2CO3 and 400 g/t of SS gel.INTRODUCTIONThe phosphorous presents in iron ore minerals is mainly in the form apatite mineral. The apatite is separated from iron ore minerals by magnetic and flotation methods (Ma, 2012). The reverse anionic flotation of iron is one of the most common method for removing phosphorus from iron concentrate (Araujo et al., 2005).Usually apatite minerals are readily floated using anionic collectors such as fatty acids (Ma, 2012). In this conditions the iron minerals are depressed and by modifying the pH in alkaline conditions, selective separation of phosphorus from iron concentrate can be achieved. Depressants including; sodium silicate (SS), starch, dextrin, guar gum and humic acids play an important role in the reverse flotation of iron ore (Kar et al., 2013; Ma, 2012; Turrer and Peres, 2010; Araujo et al., 2005). Studies have shown that SS has a better effect on iron recovery and phosphorous reduction, compared with other depressants (Tohry and Dehghani, 2016; Qi et al., 1992, Dho and Iwasaki, 1990). In most flotation processes, modifiers are used to adjust the pH. To achieve alkaline conditions, mainly pH modifiers such as carbon dioxide and sodium carbonate are used."

Jan 1, 2018

By Hao Zhang, Dezhou Wei, Qiang Zhao, Caie Zhang, Baoyu Cui, Xuetao Wang

"Nowadays, long periods of relatively low iron ore prices have made the steel industry get the greater pressure. To develop appropriate processing technology based on characteristics of the iron ore, so as to reduce the beneficiation costs, is crucial to the improvement of iron and steel enterprise competition. For a typical low-grade iron ore from northeast China, beneficiation process research was conducted based on the in-depth studies of ore characteristics. Results show that the iron grade of the ore was 31.56%, the content of FeO was 6.59%, the main iron minerals were hematite and magnetite with fine dissemination sizes and partly scattering in gangue; With the grinding fineness of 65% passing 0.074mm, and regrinding fineness of 90% passing 0.074mm, the concentrate with 66.80% iron and recovery of 82.90% was obtained via the combined flowsheet of stage grinding – classification – gravity concentration – low and high intensity magnetic separation – reverse flotation. Ratios of gravity concentration and low intensity magnetic separation were 70.21% and 7.57% respectively in 40.42% of total concentrate yield; The loss of micro-size fractions can be reduced by feeding spiral tailings into magnetic separation and flotation; It’s helpful in reducing the dosage of reagents and beneficiation costs by increasing the throughput of gravity concentration and outputting concentrate of low intensity magnetic separation.INTRODUCTION Iron and steel industries are facing the increasing pressures in the continued falling iron ore prices. In order to improve the competitiveness, it is extremely urgent for them to develop more appropriate separation process for the reduction in iron ore beneficiation cost. As a typical low-grade iron ore, Anshan-type iron ore is one of the most important iron ore resources in China [1-3]. The flowsheet of stage grinding and separation contained the classification of the coarse particles and the fine particles, the gravity concentration, the magnetic separation and the anionic reverse flotation has been widely applied for Anshan-type iron ore. With the appropriate separation progress as well as equipment, satisfactory separation results had been obtained, and mineral particles with different size were recovered separately [4-7]. However, the low recovery of fine mineral particles and the relatively high beneficiation costs still prevented the efficient application of the process [8]. For a Anshan-type low-grade iron ore, a typical process flowsheet, as mentioned earlier, with stage grading, classification of the coarse particles and the fine particles, gravity concentration, magnetic separation, anionic reverse flotation was adopted currently. And the concentrate with 67.10% iron and recovery of 75.50% was obtained and the gravity concentrate accounted for 39% of the total concentrate. However, a large amount of fine liberated iron ore particles were lost in the tailings."

Jan 1, 2018

By E. V. Zelinskaya, V. U. Starostina

"The Irkutsk region is a raw material region. There are a lot of big enterprises for extraction and processing of oil, gas, coal, iron, gold and rock salt. Besides of it, refractory clays, limestone, mica, gypsum and talc are mined in the region. The most important type of mineral raw material is a gold. More than 8.5% of the total mining in the Russian Federation is extracted in Irkutsk region. It is about 0.7% of the world production. The environmental problems of mining and processing enterprises are a complex set of issues that requires of the searching of effective methods to be solved. One of the key environmental problems remains the reduction of waste generation and the introduction of environmentally safe waste management. After analysing different methods of environmental impact assessment it is established that the method of Life Cycle Assessment is one of the most effective methods for mining production. This method base? on the material balance of flows of raw materials, products and waste. The method of Life Cycle Assessment allows to identify the effects of environmental pollution under the influence of mining and processing at a quantitative level and to show real quantitative forecasts of the possibility of managing the flows of raw materials and waste.INTRODUCTION The Irkutsk region is a raw material region. There are a lot of big enterprises for extraction and processing of oil, gas, coal, iron, gold and rock salt. Besides of it, refractory clays, limestone, mica, gypsum and talc are mined in the region. The most important type of mineral raw material is a gold. More than 8.5% of the total mining in the Russian Federation is extracted in Irkutsk region. It is about 0.7% of the world production. The main provider of precious metal is the Bodaibo region. This is a main location for the major ore companies such as “Vysochaishy”, which produces about 5.0 tons a gold per year; “Pervenets”(PJSC Polyus, the largest gold producer in Russia) - 4.5 tons/year, “Druza” - 0, 5 tons/year. Placer gold is extracted by more than 40 enterprises. In connection with this, there are many plans about a building of new and reconstruction of concentrating factories. Consequently, an increase in the volume of processing is expected. The main projects are the construction of a new mill of the Mining and processing plant GOK “Vysochaishy” with a capacity of 2.6 million tonnes of ore per year; the development of the “Uhakhan” gold-field - 23 km from the “Goltsa Vysochaishy” gold-field; the opening in the Bodaibo region the next parts of the gold-deposit ""Pervenets"". Additional, the growth in a gold production can be achieved by a store of gold in the “Sukhoi Log” deposi"

Jan 1, 2018

By D. J. Borrow, K. van Netten

"A fine coal tailings feed was selectively agglomerated using a concentrated water in oil emulsion binder consisting of 95% aqueous phase and 5% organic phase. The purpose of the study was to investigate a continuous system in plug flow, providing a rapid beneficiation technique with high selectivity and recovery. The development of the novel binder was undertaken in previous work in a batch system consisting of a high-speed blender. In this previous work, it was found that agglomeration could be achieved in 3 s, providing the binder was pre-dispersed. Furthermore, it was found that, depending on the feed, only ~1 wt% of oil was required to achieve agglomeration, some 10 times less than required in traditional oil agglomeration. In a more recent study, the technique was adapted into a continuous process. Due to the rapid speed of the process using the emulsion binder it was found that a simple flow constriction within a 1 inch pipe was sufficient to achieve the selective agglomeration observed in the batch system. In this previous study, a coal feed consisting of a flotation product was agglomerated at a superficial slurry velocity of 1.3 m/s using a partially closed ball valve as the flow constriction. In the current study, a feed consisting of fine coal tailings with an ash content of 50.1% was used to establish the influence of superficial slurry velocity on the agglomeration process. The superficial slurry velocity was varied between 1.3- 4.2 m/s, while maintaining a constant pressure drop of 100 kPa across the flow constriction. The flow constriction consisted of a partially closed ball valve. It was found that increasing the superficial slurry velocity across the flow constriction reduced the amount of organic liquid required to achieve agglomeration. Under the optimum conditions, a combustible recovery of 80.4% was achieved at a product ash content of 9.6%. This work demonstrates a valuable product can be rapidly produced from tailings material using the novel emulsion binder. INTRODUCTION A significant opportunity exists to recover fine coal from material that is currently classified as waste. This waste material, also called tailings, is currently considered not economic to process due to its high ash content, low solids concentration, and the fine size of the particles. Thus, for this opportunity to be realised, a process is required that is highly selective and has the ability to economically recover fine particles at high throughputs. The technique of oil agglomeration has previously been considered as a candidate for the recovery of fine coal, as it is highly selective and has no lower limit on the size of particle that can be recovered (Capes and Jonasson, 1989). However, the cost of the oil required as the binding agent in the process has proven to be a significant barrier to any long-term applications (Swanson, Nicol, and Bensley, 1977). Recently, however, Yoon and co-workers have developed an ultrafine coal separation process that utilizes an oil phase for the recovery of the hydrophobic coal particles and have implemented an oil recycle to greatly reduce the consumption and thus cost of the oil (Yoon et al., 2016)."

Jan 1, 2018

By Jia Muxin

The adsorption behaviors of metal ions on a silicate mineral and the flotability of a metalized silicate mineral with sodium oleate as collector are closely related to the structure of the silicate mineral. The adsorption isothermals of the metal ions on different silicate minerals are studied, the parameters of the isothermal give the information how many surface oxygen anions a metal ions is attached to, from this information and the structure of the mineral the site where a metal ion is attached can be guessed (The adsorption isothermals and adsorption behaviors with pH are fitted with Temkin, Frenudlich and Kurbatov equations respectively). Metal ions as Cu2+, Ni2+, Zn2+ are attached to the oxygen anions of surface species –Si-O– on the quartz surface, most of them coordinate to only one surface oxygen, their adsorption ability on quartz is low, but this metal ions on quartz surface protrude out of the surface perfectly, so their ability to combine with oleate acid radical is excellent. Quartz can be activated well by such metal ions. The isothermal of Fe3+ on quartz indicates these cations coordinates with more than two surface oxygen anions. This means the Fe3+ nucleates on quartz surface in the form of Fe(OH)3 colloid particles. The isothermals of Cu2+, Ni2+, Zn2+ Fe3+ on spodumene shows such ions coordinate with more than two surface oxygen anions, it indicate these ions may attach to the position where Li+ is formerly exists, such metal ions stay in a cave on the mineral surface, their adsorption abilities on spodumene are quite well, but they are affect by the oxygen anions of the two Si tetrahedron chains, the can almost not activate this mineral. These cations may attach on the site where Al3+ exists on the muscovite surface, just like spodumene, muscovite can not be activated well by such cations. Pt2+ has a large ion radius, as Pauling’s rules depicts polyhedron can not attach to Si tetrahedron well, the adsorption ability of Pt2+ on quartz is low and quartz is activated badly by Pt2+. On the other Pt2+ can adsorb well on spodumene and muscovite well and activated them well because it is not affected so bad by the tetrahedron oxygen anions of the minerals for their its large radius. The isothermal of Ca2+ on quartz indicates a Ca2+ coordinates with less than one surface oxygen anion, this means Ca2+ attaches on quartz mainly by physical adsorption. The adsorption abilities on mineral surface and the interaction abilities with oleate acid radical of the transition metal ions with the same valence are guessed to be determined by their d electron number, the rules should be d1<d2<d3<d4>d5<d6<d7<d8<d9>d10. Hydrogen bond may play an important rule in the activation of the mineral by HF and the interaction of the HF activated silicate mineral with collectors. The general rule is high bond valence and small metal ion radius surface species –Me-O can be activated well by HF with sodium oleate as collector. For example – SiIV-OH is neutral while –SiIV-FH+ and –SiVI-FH+0.33 are positively charged, the positively charged surface species are more likely to connect oleate acid radical via hydrogen bonds.

Jan 1, 2003

By Jin Duan, Qi Zheng, Bo Yan, Li-cheng Ma, Xiao-kui Che

"The aim of this study was to develop an approach for the selectively removal of Zn(II) from heavy metal-bearing-wastewaters produced by gold chemical industry using magnetic chitosan based adsorbents. Chitosan beads were prepared by cross-linked modification of Fe3O4-chitosan bead using epichlorohydrin as the cross-linker. Both Zn(II) inprinted magnetic chitosan hydrogel bead (Zn-MCHB) and unprinted magnetic chitosan hydrogel bead (MCHB) were prepared and batch adsorption experiments were used to evaluate their adsorption capacities and selectivities. Single adsorption of Cu2+, Pb2+, Zn2+ and Ni2+ showed that both MCHB and Zn-MCHB adsorbs all the four metals and had an affinity in the order of Cu2+ > Pb2+ > Zn2+ > Ni2+. The binary adsorption revealed that the two adsorbents preferentially adsorb Cu2+/Pb2+ from Zn2+-Cu2+/ Zn2+-Pb2+ binary systems. However, MCHB does not show any selectivity in Zn2+-Ni2+ system. In contrast, Zn- MCHB preferentially adsorbs Zn2+ from Zn2+-Ni2+ binary system. Furthermore, the adsorption selectivity is predictable from stability constants of the metals with the amino group of chitosan. The information revealed in this work can be used for further applications in the treatment of wastewater containing a range of heavy metals from the gold chemical industry."

Jan 1, 2014

By Charlene Gokhale

Geopolymerisation has emerged during the last few years as an industrial and ecological approach to construction and waste management. By utilizing waste materials and their reactive properties, it is now possible to create geopolymers systems that not only mechanically durable enough to be used as construction materials but are also potential stable immobilisation systems for toxic waste. Previous studies by Van Jaarsveld et al. (1997) and Van Jaarsveld et al. (1998) have reported on the numerous applications of geopolymers in the immobilisation of toxic metals. Research into the possible utilisation of geopolymers as an encapsulation media for organic waste has however been rare. This paper therefore provides an insight into the possible utilisation of geopolymers as a binder for hazardous organic materials.

Jan 1, 2003

By M. L. Liu

This work reports the results about the determination of mean activity coefficients and relative partial molar free energies for copper sulfide mineral bioleaching solutions by potentiometric method at 25ºC. The experimental potentiometric data were obtained by combining a solid state membrane-cupric ion selective electrode (Cu2+ ISE), containing a KNO3 filling solution, and an Ag/AgCl electrode. The measurements were performed in different series of copper sulfide mineral bioleaching solutions. The non-ideal behavior of the system was described on the base of the Pitzer ion-interaction model for mixed salts. Meanwhile, the relative partial molar free energies of bioleaching solution were investigated. The determination of the thermodynamic properties offers a basic data for the study of copper sulfide mineral bioleaching solutions.

Jan 1, 2014

By Cesar Gomez, Jaime Álvarez, Lisette Wen

Laboratory mechanical flotation cells are extensively used in mineral processing for running batch flotation tests with a variety of purposes, for example assessing feed characteristics, determining flotation kinetics, or testing of new reagents and procedures. It is known that the results obtained depend on the operation mode, self-aerated or forced-air, and on the operating conditions selected for the test, in particular impeller speed and gas flow rate. These different results are a consequence of changes in size distribution of the generated bubble population and its remarkable evolution when frother is added; variations in bubble size affect the bubble surface area flux (BSAF), a variable which correlates with particle collection. Results of a two-phase (air-water) test program designed to measure bubble size for a variety of combinations of impeller type and speed, gas flow rate, frother type and concentration, and cell volume, demonstrated the wide range of BSAF with which the cell can be operated. The results obtained in this work demonstrated that gas dispersion in a forced-air lab flotation machine is significantly affected by the characteristics of the impeller/cell geometry combination in use, and the operating conditions selected. Operating conditions must be carefully selected and maintained during the test to ensure consistent results, in particular when frother concentrations below 20 ppm are used, because frother concentration in the cell will decrease as flotation progresses as a consequence of frother partitioning to the concentrate.

Jan 1, 2014

By Felipe Sepulveda, Edelmira Gálvez, Luis Cisternas

"In mineral processing, the recovery and/or concentration of the value components cannot occur in one operational stage, therefore requiring the use of separation circuits based on several flotation stages. The components to be separated are typically distributed at different concentrations and different particle sizes, resulting in different levels of recovery. Typically, more than one value component must be selectively removed by exploiting the differences in the components’ floatability at different pH values, pulp potential and particle size. Several methods for the design of these circuits are available in the literature, but comparatively few studies present circuit analysis tools or address the design of a multiple-product flotation circuit. In this study, global sensitivity analysis was used to analyze a flotation circuit with several products, such as copper, lead and zinc. This analysis was based on the Eureka mine concentrator plant. The analysis was performed for each of the sections of the circuit as an overall evaluation of the circuit. The Sobol’ method and the correlation method were used to evaluate the Eureka mine concentrator plant using the SimLab 2.2 software."

Jan 1, 2014

By J. Lindström, J. Hamuyuni, M. Lundström, J. Aromaa

"The rising demand for metals today, coupled with the scarcity of primary sources for raw materials threatens both technological advancements and industrial manufacturing. In order to meet the demand, metals and other resources trapped in waste streams, have to be harnessed. This philosophy supports circular economy, where metals and other resources are kept in a closed loop. The pickling acid recovery system of most stainless steel production is one such example where the dissolved metals such as iron, nickel and chromium are currently not completely recovered due to the limitations of the current technologies. The aim of this study was to assess the available metals recovery methods from extremely concentrated acids. The main aim is to simultaneously recover metals and keep sulphuric acid reusable in acid circulation process. From the available literature, the most promising methods were chosen for laboratory experiments. Based on experimental work, the results and observations of electrodeposition, solvent extraction, and freeze crystallization are provided. KEYWORDS Pickling acid, metal recovery, solvent extraction, cathodic polarization, Freeze crystallization. INTRODUCTION Pickling in stainless steel production is an essential surface treatment process (Regel-Rosocka, M. (2010); Agrawal and Sahu, 2009). It is applied for removing surface films such as oxides and chromium-depleted layers to improve the corrosion resistance and surface finish of steel (Regel-Rosocka, 2010). Whilst the process greatly improves the surface finish of the stainless steel, it generates large amount of used acid, containing dissolved metals including chromium, iron, and nickel (Agrawal and Sahu, 2009). Recovery of acid is common practice for most steel producing industries (Nyman and Koivunen, 1986). In this work, acid regeneration process is investigated so as to simultaneously reusing sulfuric acid and recovering the dissolved metals. Recovery of valuable metals even in very small amounts would also bring additional revenue to the steel production industry. At a time when metal production has also been challenged by lack of natural resources for raw materials, secondary sources for metals such as the acid pickling process therefore, have greater potential as supplements. From earlier studies, electrodeposition (Giovanardi and Orlando, 2011; Kuznetsov et al., 200; Rögener et al., 2012; Surviliene et al., 2006), solvent extraction (Alguacil and López 1996; Haghshenas et al., 2009; Kesieme et al., 2013) and freeze crystallization (Beyer et al.,2003; Hasan et al.,2017; Van der Ham et al., 1999) are some of the most established potential methods. Earlier studies have also shown that simultaneous recovery of acid and metals would require combination of different methods. This is primarily due to the nature of very stable metal containing complex compounds formed during pickling. These complexes must be broken down to free the metals for further recovery processes."

Jan 1, 2018

By Rhulani F. Maluleke, Francis W. Petersen, John H. Marsh, Johann de T. Steyl, Allan Nesbitt

"Pressure leaching of chalcopyrite and nickeliferrous pyrrotite at temperatures between 105 and 200 ºC has been proposed as a potentially viable route for the extraction of mineral elements from sulphide concentrates. In general, these concentrates contain iron, and the economic success of the processes is partially dependent on the choice of the environmentally acceptable iron-removal technique. One of the most widely used methods for the removal of iron from sulphate liquors is precipitation as hematite, goethite, or jarosite. The nature of the iron precipitate formed dictates downstream dewatering and residue treatment and disposal options. However, a better understanding of iron precipitation under the defined process conditions would consequently be of benefit in process design and optimisation.This study investigated the precipitation of iron in the autoclave at temperatures between 105 and 200 ºC. The effects of temperature, acid concentration, iron concentration, and the presence of other metal cations on the nature and composition of the precipitates were determined."

Jan 1, 2003

By C. Y. Wang

Anodic reaction mechanism of complicated antimony-lead concentrate in Slurry Electrolysis has been investigated by the anodic polarization curves determined under various conditions. The main reactions on the anode are the oxidation of FeCln (2-n), though the oxidation of jamesonite particle on the anode can occur during the whole process, it is less. With the help of mineralogy study and relevant tests, the leaching reaction mechanism of jamesonite and gudmundite during Slurry Electroly-sis has been ascertained also. Because of the oxidation reaction of FeCl3 produced by antimony-lead concentrate itself, the non-oxidation complex acid dissolution of jamesonite, the oxidation complex acid dissolution of gudmundite, and the oxidation of air carried by stirring, the leaching ratio of antimony reaches to about 35% when using HCl-NH4Cl solution to leach antimony-lead concentrate directly. So given the theoretical electric quantity, which to oxide antimony in Slurry Electrolysis, all of antimony, lead and iron, which contained in antimony-lead concentrate, are leached.

Jan 1, 2014

By F. Q. Cheng

As the important potash, the product yield of KCl in winter is low and the resources waste is serious according to the deficiency of collectors, which can be used in this condition currently. This paper studied on the change of contact angle, turbidity, and flotation recovery of KCl particles when different chain lengths, ratios of amines were used as collectors in KCl flotation process to get a new mixed collector. The contact angle values of KCl crystal in its brine solution added different amine collectors were first measured by captive bubble method. The turbidity of brine solutions were then measured by the laboratory turbidimeter at room temperature when different amine collectors were contained. In the end micro-flotation experiment using mixed amine with fixed ratios and ODA as collectors respectively at 5 °C, 23 °C were performed. The results show when the ratio of the mixed amine is DDA- 20%, ODA-60%, C20-20%, the contact angle at KCl surface is the maximum and the hydrophobic state is best. Meanwhile the result of turbidity measurement indicates that the dispersion of mixed amine colloids is better than the ODA collector due to the addition of DDA, which plays the role of frother. The flotation results also prove that the mixed amine is not only fit for the KCl flotation at room temperature but also fit for its flotation at low temperature. This study provides strong technical support to extend the production time of potash business in Chaerhan areas in China.

Sep 1, 2012

By Maurício Torem, Gabriela Huaman, Antonio Merma

The purpose of this review paper is to succinctly present the most significant works related to Mineral Processing and Environmental Bioremediation and developed by the Mineral and Environmental Technology Group (METG) of the Materials Engineering Department of the Pontifical Catholic University of Rio de Janeiro (PUC-Rio). In mineral processing it was emphasized the use of the Rhodococcus opacus bacteria as a bioreagent in the bioflotation of some mineral samples (magnesite, calcite, hematite, quartz and apatite). The adsorption of the bacterial cells on the mineral surface can be due to specific and/or non-specific interactions, which will depend on several factors, as their surface charge and hydrophobic character. The zeta potential evaluation of the mineral particles before and after interaction with the R. opacus cells showed that the biomass modified the zeta potential profiles of the minerals, which confirm the adsorption of bacterial cells on the mineral surface. Moreover, the bacterial cells adsorbed caused a change in the mineral flotability which is related to a change in their hydrophobic character, thus, the mineral bioflotability was found to be dependent on the pH and the bacterial concentration. On the other hand, the environmental bioremetiation assessed the biosorption potential of three metal ions (lead, copper, and cobalt) by four different biomass Streptomyces lunalinharesii, Rhodococcus opacus, Rhodococcus ruber and coconut shell powder. For this purpose, biosorption process was characterized under different operating conditions such as initial pH and biosorbent dosage. The Freundlich and Langmuir isotherm models were applied to the equilibrium data obtained at different concentration.

Jan 1, 2014

The flotation of nickel sulphide minerals is normally difficult in the presence of serpentine minerals due to the coating of serpentine particles on the nickel mineral surface. To improve the flotation, dispersants such as polyphosphate and carboxy methyl cellulose are normally used to remove the slime coating. However, in the flotation using high ionic strength process water, these dispersants are invalid due to their ionic nature. In this study, a new type of non-ionic dispersants, Pluronic triblock copolymers were examined with an objective of improving the flotation of ultrafine pentlandite (a nickel sulphide mineral) in the presence of lizardite (a serpentine mineral) in saline water. Three Pluronic triblock copolymers varying in solubility and hydrophile-lipophile balance (HLB) values were studied by flotation tests, settling tests and froth measurement. It was found that two of the copolymers improved pentlandite flotation against lizardite, and one copolymer deteriorated the flotation. The effect of Pluronic triblock copolymers on the flotation was actually linked to their dispersibility and foamability, which were governed by their physical properties. The two copolymers with a higher solubility or HLB value produced more stable mineral suspensions and more stable froth in the flotation resulting in better nickel grade and recovery in both rougher and cleaner flotation. Keywords: ultrafine particle, flotation, slime coating, dispersion, saline water, triblock copolymers

Sep 1, 2012

By M. Vulkov

The paper is focused on the optimal selection of grinding medium for a drum mill. The decision-making is based on the fuzzy multiple attribute approach. One way to optimize the grinding process in a tumbling mill is associated with the development and testing a new shape of grinding body. Family of new grinding bodies ? spheroidal tetrahedrons (tetraballpebs) has been manufactured. Two types of spheroidal tetrahedrons and a classical ball (sphere) with one and the same weight are compared. A fuzzy entropy method to calculate the weight of the attributes is suggested. A grinding body which is the best approximation to the fuzzy formulated technological conditions is selected. Keywords: grinding, spheroidal tetrahedrons (tetraballpebs), balls, fuzzy sets

Sep 1, 2012

By E. Guerrini, M. Maccagni, J. Nielsen

"The solution for the treatment of the EAFD has not yet been fully achieved. Some of this dust has still not found an appropriate final destination. Large consortium treatment plants are quite expensive both in terms of investment and operating cost. Meanwhile, the tolling expenses for steel production companies are becoming very important, causing them to look for alternatives. Some steel plants are looking to close their production loop by internal treatment of their dust. Some years ago, Engitec began studying the coupling of the EZINEX® Process, an ammonium chloride electrolysis to recover the zinc contained in the EAFD, with the INDUTEC® Process, a pyro process based on an induction furnace that can convert EAFD into a C.Z.O. similar to the Waelz oxide. The combination of these two processes provides an alternative to the existing treatment options and is particularly interesting for relatively small capacities. In this paper, we would like to give the latest update about these two processes and their possible integration INTRODUCTION Zinc is contained in numerous wastes and secondary raw materials that can be thought of as high zinc concentrate mines. This is a very interesting source of Zn that is typically easily exploitable. Unfortunately, only a portion of these materials are currently processed to recover the metal value, while stabilized or unstabilized landfilling is often the final destination. Pyrometallurgical processes are mainly used to convert the zinc into crude zinc oxide (CZO). The various processes are very similar and characterized by the fact that the zinc bearing materials are usually submitted to a thermal treatment [1] in which the zinc is reduced, vaporized and re-oxidized producing CZO. This material not only contains zinc oxide, but also relatively high concentrations of heavy metals. Many potential CZO sources, such as electric arc furnace dust (EAF), galvanizing ashes, brass foundry and converters fumes also contain chlorides, fluorides and alkali metals that will transfer to the CZO. The classic example is the Waelz oxide [2]. This CZO is an intermediate product that must be transformed into zinc salts or zinc metal. Until now, the conversion to zinc metal is done through two main processes: the sulphate leaching and electrowinning system and the Imperial Smelting Process (ISP). ISP is facing a crisis for technical and economic reasons that has led to the closing of most of the existing plants. In any case, before being fed to one of these two processes, the CZO must be treated to eliminate or reduce some of the contained impurities. In particular, the halides are most harmful to these processes."

Jan 1, 2018

By Alejandro Uribe-Salas, Fabiola Nava-Alonso, Gloria Dávila-Pulido

This paper presents results of an experimental study performed on the role of calcium sulfate present in flotation water on sphalerite flotation in the Pb/Cu circuit (non Cu-activated sphalerite) and in the Zn circuit (Cu-activated sphalerite). In the Pb/Cu circuit calcium ions adsorb on the negatively-charged sphalerite favoring xanthate adsorption and therefore making sphalerite floatable; experimental measurements show sphalerite contact angle increases with calcium concentration while xanthate adsorption onto sphalerite increases with the increase of pH and calcium concentration. Gypsum (CaSO4·2H2O) eventually present due to calcium sulfate precipitation is not detrimental to flotation at this stage since it is negatively charged at pH 9 and therefore, does not adhere onto the surface of negatively-charged sphalerite. In the zinc circuit, Cu-activated sphalerite decreases its negative charge (or even becomes positively charged) and develops some hydrophobicity due to the polysulfide produced by Cu-activation. At this stage calcium ions do not interact with the mineral surface and therefore do not favor xanthate adsorption; nevertheless, precipitated gypsum particles do adhere onto the mineral surface, greatly affecting its floatability (e.g., contact angle). Addition of sodium carbonate to dissolve gypsum and to precipitate calcium as calcium carbonate, which disperses in the bulk of the suspension, effectively restores mineral hydrophobicity. SEM observations coupled with EDS analysis clearly illustrate and support the above sequence of events.

Jan 1, 2014

By Volker Vogt, Wolfgang Sand, Eberhard Gock

"It was discovered that the selective activity of bacteria during the extraction of raw material concentrates by means of flotation could also be achieved with extracellular polymeric substances (EPS) excreted by bacteria. EPS, which is extracted by means of centrifuging bacterial cultures, can help to significantly reduce the use of cyanides, approximately 200,000 t/a of which are used for ore dressing today.The bacterium used was Acidithiobacillus ferrooxidans. In order to identify the bandwidth of the oxidation activity, 20 bacterial strains of the strain collection of the University of Hamburg were attracted to iron(II) sulfate and pyrite under defined conditions. All strains oxidized iron(II) sulfate ten times faster than pyrite.EPS has so far been derived from four strains. In general, EPS extracts are divided into a hydrophilic and a hydrophobic fraction. The hydrophilic fraction is composed of e.g. fucose, rhamnose and glucose; fatty acids such as dodecanoic acid, hexadecanoic acid, octadecanoic acid and nonadecanoic acid were found in the hydrophobic fraction.Pure mineral phases and mineral mixtures were used for the flotation tests. As opposed to current knowledge, the results were reproducible with technical flotation machines."

Jan 1, 2003