Search Documents

By V. A. Feofanov

Technogenic water of ore mining enterprises, nonferrous metals operations, the enterprises of electroplating and instrument making, containing copper in the form of those or other connections can serve as perspective sources on receiving the copper-bearing raw material. Extraction of copper from the given water also solves a problem of water treating from a toxic component that reduces environmental load at evacuation of water in an open basin. The method of case hardening allows extracting copper selectively with reception of a deposit with the content of copper up to 70%. Weakness of the method is its efficiency basically in acid reduction, and also its low degree of copper extraction. On the basis of case hardening the method of galvanic coagulation is devised. It is based on the work of a short-circuited galvanic cell of iron-coke at variable contact of coupled metals components among themselves, cleared by the oxygen of air. The following processes of galvanic coagulation are considered: ? Extraction of copper; ? Formation ferrites of copper; ? Copper sorption on just-aggregated oxide forms of iron. Establishing conditions for passing the given stages provides an opportunity of copper extraction from technogenic water at any value of ??, content of salt and concentration of copper with reception of a compact deposit from which it is possible to extract copper by the known ways of enrichment and metallurgy. Investigations on optimization and intensification of galvanic coagulation with the purpose of reception the maximum rich deposit on copper have shown that the average contents of copper in a solution of 100~200 mg/dm3 the contents of copper in a deposit is 6%~10% at extraction 85%~90%, depending on characteristics of treated technogenic water. Using methods of scanning microscopy it is determined structures, composition and mechanism of phase formation in investigated electro-chemical process. The second stage of galvanic coagulation increases a degree of copper extraction up to 98%~99% that allows returning the cleared waters in circulation for waste recycling or evacuation in an open basin. Nowadays the method of galvanic coagulation is the most acceptable for copper extraction from technogenic water both from the point of view of efficiency and instrument setting that allows applying the method in conditions of the working enterprises.

Jan 1, 2014

By Dianyin Liang, Hongxiang Ran, Xiaoming Wang, Xiaoou Xia

"This paper presents a new magnetic separator, which can be applied to increase the grade of fine magnetite ore feeding of ball mill. This innovative equipment possesses a rotating magnetic system and has a magnetic field of rapid polarity change which can strengthen the destruction of magnetic agglomerations and the dispersion of minerals to improve the quality of separation. Now this type separators have been successfully applied in several large concentrating plants such as Shuichang Iron Mine under Shouang Mining Company in China. Finally, this paper outlines practical results focused on feed grade and tailing yield, the results are showing that the quality of feeding can be improve tremendously. Hence, a new generator of rotating magnetic field has been paved. INTRODUCTION Jidong region in China is the important origin of iron ore, the characteristics of the iron ore in this region is low grade and complex, the iron mine discharges fine powder tailings reaches tens of millions of tons each year, in the wind action easy to form sand, this poses a threat to the atmosphere environment of Beijing. In order to reduce the mixing of large amount of useless ore and reduce the energy consumption of mill operation, a high efficiency pregrinding equipment is needed. Rotating magnetic field separator (RMS) is an advanced equipment, the main advantage of RMS is the significant reduction in particle entrapment and can easily break magnetic agglomeration. This reduction is so significant that RMS is capable of operating very close to theoritical limit for separator precision and can increace efficiency in selection process.Some expenrimental work on dry rotating magnetic field separation has been carried out in July 1998 in the company Ka Pty Ltd, then in 2008 BGRIMM developed industrial separation XCTG0816 in Shandong province . The wet RMS was researched in1960s in Former Soviet Union and the first industrial equipment was developed by BGRIMM in 1970s,then in 1990s wet RMS was applied in Ansteel group corporation. In 2017,6 units large wet RMS (SXCT1230)which were the largest RMS was applied in Sichuan province. No matter wet RMS and dry RMS, although they are used in differenct applications, they have some common research.in addition ,they all have good use effect."

Jan 1, 2018

By R. V. Kononko, A. Yu. Chikin, R. N. Rakhmeev, Yu. O. Fedorov

"The focus of the study is finding a solution that can help to improve diamond recovery in diamond-bearing gravity concentrates upgrading flowsheets. The purpose of the study was to develop and prove scientifically a separation method of diamonds recovery from gravity concentrates regardless of their fluorescence ability induced by X-ray radiation. Two promising recovery methods applicable to diamonds of this type are proposed, i.e. an X-ray radiometric method based on an instantaneous analysis of a secondary X-ray spectrum of separated particles, and a triboelectric method that relies on noncontact measurements of particle charges obtained during its motion in a vibratory tray. As a part of the laboratory study, X-ray fluorescence spectra of the collection of diamond crystals and main associated minerals and rocks at a particle size of -6+3 mm were produced. The analysis of the produced secondary X-ray spectra showed a significant difference between crystals, minerals and rocks within the analytical area of Ca, Fe and Zr due to the absence of calcium, iron and zircon elements in diamonds. Additionally, the scattered X-radiation level of diamonds substantially increased under the influence of X-ray radiation. Such a difference is a physical base of a new method of diamonds recovery from mineral mixtures. The laboratory study on triboelectric characteristics showed that a significant portion of diamonds gained an electric charge of a magnitude that was much higher, compared to associated minerals and rocks. The laboratory and industrial tests and the separation indicators demonstrated a high efficiency. A proposed X-ray radiometric method provides recovery of all types of diamonds regardless of X-ray fluorescence levels, with high selectivity and recovery rate of at least 98%. This proposed separation method is protected by a patent of Russian Federation (No. 2551486, “A method of X-ray radiometric separation of diamond-bearing materials”). Triboelectric separation organized in two stages (main and control) ensures recovery of up to 98-100% of diamonds at a particle size -5+2 and -2+1 mm,. More than 10 triboelectric separators successfully operate in active diamond processing plants in the Russian Federation."

Jan 1, 2018

By J. Jirestig

Poor grade iron ore, suffering from interlocked particles, is challenging for any process technology. Extensive grinding is required to attain liberation and to yield concentrates of desired grade. Fine particles are commonly very difficult to retrieve, resulting in value losses to tailings. In this paper, results from HGMS tests on fine to ultra fine hematite are reported. Special emphasis is put on slurry flow velocity. If hydrodynamic drag force, i.e. flow velocity is not controlled and kept constant during the feed and/or rinse phase, fine particles will not be captured and retained. Flow velocity control and constant flow during separation are achieved by discharge valves/slots and parallel magnetic flux and pulp flow configuration. In tests, increased slurry velocity from 178 to 268mm/s caused Fe-recovery to drop from 78 to 48%. Proving that flow velocity control is essential to optimise grade and recovery. HGMS tests at the Metso mineral laboratory on natural (weathered) hematite fines clearly show a large potential to recover valuables, currently lost to tailings. Even at particle size distributions as low as D80=35µm concentrate grades and recovery are very satisfying. Two samples, in-plant desliming rejects (D80=35µm and 50µm) where significantly upgraded and recovered, from 45,3% to 63,6% and 53,0% to 63,4% Fe, at 73,8% and 81,1% Fe-recovery respectively. Other types of in plant rejects, such as gravity separation or WHIMS tailings, also benefits from HGMS separation. Gravity separation reject, 55,8% Fe, at D80=500µm was tested, yielding a magnetic concentrate of 60,8% Fe at 50,7% Fe-recovery. The results indicated that the hematite was poorly liberated. HGMS separation was repeated after a regrind to D80 150µm, resulting in a magnetic concentrate of 62,8% Fe at 75,9% Fe-recovery. The tests prove that hematite, presently lost to tailings streams, can be recovered by HGMS and thereby significantly contribute to improved overall economy. Keywords: HGMS, magnetic separation, recovery of ultra-fine hematite, Indian hematite ores, hematite recovery from tailings

Sep 1, 2012

By M. Paymardi, A. Foroutan, T. P. Oladele, M. Abbaszadeh

"Reducing the amount of zinc and iron in lead concentrate is one of the important aspects of processing in lead and zinc flotation plants which results in improvement of lead concentrate quality and prevents zinc loss. In mineral flotation industries, lignin sulfonates are known for their depressant properties for both non-metallic and sulfide minerals such as pyrite and pyrrhotite.This paper investigates the effect of lignin sulfonate on flotation of galena, sphalerite and pyrite in sulfidic lead and zinc bearing ores. Batch flotation tests were carried out on a high pre-activated zinc samples. The feed contains 0.9% lead, 2.3% zinc and 7.5% iron. The dosage of all reagents such as sodium cyanide, zinc sulfate, ethyl xanthate and methyl isobutyl carbinol (MIBC) were kept constant for lead flotation step except calcium lignin sulfonate (CLS) that was varied between 0 and 80 gr/ton.Results for lead rougher concentrate showed that the grade of lead increased by 2.7% while the recovery decreased around 4 % at the highest dosage of CLS. Furthermore, zinc recovery decreased by 6.3% with no significant change in grade. Iron recovery in lead rougher concentrate decreased by 2.3 % while the grade changed around 1%. In sphalerite flotation step, CLS dosage was changed in the range of 0 to 80 gr/ton while the dosage of other reagents such as copper sulfate, lime, amil xanthate and MIBC were kept constant. In this step, no decreasing in grade and recovery of zinc was observed, while iron recovery decreased. It was suggested that CLS has a depression effect on sphalerite in conjunction with other zinc depressants such as zinc sulfate and sodium cyanide. CLS was further used in plant with non-pre-activated zinc minerals. Similar trends were observed in plant.INTRODUCTIONlead-zinc sulfide minerals play an important role in the production of lead and zinc metals in the mineral processing industry (Luo, Feng et al. 2016). Due to complexity of the lead-zinc ores mineralogy, in some situations, their flotation properties vary significantly from one deposit to another one even in itself (Bulatovic 2007)."

Jan 1, 2018

By Lokesh K. Thakur, Peter Radziszewski

"For the cases tested (11 mills with 15 operating conditions), the Bond abrasion test steel media wear rate prediction gives an overall error of 73% and a standard deviation of 192.5%. However, total steel media wear in a given mill (ball or SAG) grinding process is a product of three recognised wear mechanisms -- impact, abrasion, and corrosion. A total media wear model can be defined on the assumption that the effect of each wear mechanism can be independently determined which allows for a total media wear model to be defined as the summation of the wear result of each mechanism (eqn. 1). It is assumed that impact and abrasive media wear is a function of the energy dissipated in impact and abrasion as estimated by a DEM charge motion simulation. Corrosive media wear is assumed to be a function of the media surface area present in a mill.The 3 initial tests developed (steel abrasion wheel, corrosion batch mill, impact chamber) coupled with the impact and abrasion energy spectra from a DEM charge motion simulation produced total steel wear rate results for the same cases as the Bond abrasion test giving an overall error of 0% and a standard deviation of 66.1%. However, if one were to consider the general observation that wear is proportional to energy and maintain the assumption that corrosion is proportional to media surface area then one would realize that the total media wear eqn. (1) can be reduced to eqn. (2). As this is a linear equation and one has, for the same mill, media wear and operating data for three different operating cases, one obtains three equations with three unknowns. This defines a simple matrix manipulation to determine the constants k1, k2 and k3. From the previous data set, we had 6 identical mills grinding the same ore but having different worn liner profiles and charge volume which provided the opportunity to average out the ki values over 20 combinations of 3 cases. With the determined ki values, it was possible to determine a second estimate of the contributions of impact, abrasion and corrosion to total media wear giving an overall error of 0% and a standard deviation of 56%."

Jan 1, 2003

By Katarina Theander, Robert J. Pugh

In the flotation process, control of the stability of the froth is extremely critical. In the case where the froth is too stable then mechanical entrainment of particles can occur but in the opposite case, where the froth is too unstable and difficult to skimm-off, then a reduction in recovery can result. In minerals and deinking flotation, commercial fatty acids are used and may act as both both collectors and frothers. However, frequently the fatty acids are mixed with nonionic ethoxylated surfactants to give more effective froth control and increase the flotation performance. It is of interest to note from the surface chemistry literature, that such mixtures may cause synergistic effects in surface activity which may explain changes in bubble size, foaming and carry over of particles. In the present study, we have carried out foaming and drainage experiment with oleic acid and model nonionic surfactants; hexa(ethylene glycol) mono-dodecyl ether, C12E6 and tetra (ethylene glycol) mono-dodecyl ether, C12E4 both in separate and mixed systems. Frothing was carried out in a column, equipped with a series of conductivity electrodes which enabled the water content of the froth to be measured along the length of the column, during various stages of the drainage process. The variation in water content of the froth enabled the process to be characterised by distinct three stages; (a) an entrainment state where the water transfer from the bulk phase to the froth was dominant (b) a steady state when entrainment and drainage are balanced and no water is transferred to or from the froth and (c) the drainage step when drainage predominates and the volume of the bulk phase increases. We also carried out surface tension measurements on the oleic acid/ nonionic systems and related the results to the frothing and drainage performance. From the surface tension data, the adsorption interaction parameter of the mixed systems at the air/solution interface could be calculated and was found to depend on the oleate/ nonionic surfactant ratio. This value was related to the frothing performance and the results indicated a positive interaction parameter for the mixed surfactant systems which could explained the synergistic effects in frothing performance.

Jan 1, 2003

By V. A. Luganov

Methods of treatment of pyrite concentrates differ, depending on the content of pyrite and non-ferrous metals: oxidation roasting, sulphatization roasting, smelting, direct hydrometallurgical treatment and so on. Existing technologies do not provide for high recovery of metals, expenses associated with existing technologies are high, and environmental issues, associated with the existing technologies need serious attention. We have developed universal technology of the activating-dissociating autogenous roasting of pyrite concentrates using air based, or air, enriched with oxygen, blow. The basic process is taking place in accordance with the following reaction: (1-x)FeS2 + (1-2x)O2 = Fe1-xS + (1-2x)SO2 +Q The products of this reaction are pyrrhotinized cinder and roasting gases, rich in SO2 (up to 18 % in case of air blow) and poor in SO3, that contain up to 1 % of elemental sulphur. Cinder contains different forms of pyrrhotite. These forms of pyrrhotite differ by its content (from Fe0.843S to Fe0.945S), thermodynamic, magnetic (from 4.10-1 to 3.6 SI units), flotation properties (with pyrite dissociation the ?-potential of the product is moving towards more electrically positive charge, from 0.95 for pyrite to 0.2 for dissociation products) and other properties that depend on the conditions of roasting. The combination of pyrrhotizing roasting with different methods of cinder treatment allows to increase the level of sulphatization of non-ferrous metals during the roasting; reduce the amount of blow used during the processing; reduce dust losses to the gas phase; reduce the capacity of gas cleaning system and increase resistance to corrosion of the gas-treatment system, used for the production of sulfuric acid from pyrites. This combination of treatments also allows to use magnetic separation and flotation for separation of ferrous and non-ferrous metal compounds during cinder treatment; perform de-arsenation of arsenic containing concentrates and by-products. Pyrrhotinized cinder may be treated by oxidizing and non-oxidizing hydrometallurgical methods. Keywords: Pyrite, polymetallic ores, sulphidization roasting, pyrrhotite, magnetic separation, arsenic sulphide

Sep 1, 2012

By A. Y. Senchenko, S. G. Rybkin, A. V. Aksenov

"Oxidized nickel ores are important source for nickel production in Russia. Considerable explored reserves of oxidized nickel ores with relatively low nickel content, about 0.6-1.4%, are concentrated in the Ural region of Russia. Conventional process flowsheet with the use of blast matte smelting, applied in particularly by JSC “Ufaleynickel”, proves itself as extremely low-margin technology. This paper will examine development of a new more cost-efficient process involving integrated treatment of oxidized nickel ores using the ore from Serovskoye deposit as an example. Target products of this process are hydrate residues containing up to 15 % of nickel and 0.3 % of cobalt, as well as saleable salts of magnesium sulphate and ammonium suplphate. This innovative process includes roasting of a mixture composed of ground ore and sulphuric acid at 650 °?. Sulphate roasted product is then leached in a weak sulphuric acid solution with the following separation of liquid from insoluble solids. Sulphate solution is neutralized by aqua ammonia in two stages until media pH is 3.0-3.5 and 7.5-8.0 with detachment of iron- and nickel-bearing hydrate residues respectively. The mother solution is boiled out resulting in salt crystals which are then dried and roasted at 500-600 °? to obtain magnesium sulphate. The gases generated during salts roasting are captured with production of ammonium sulphate. The developed technology demonstrates higher potential in terms of its economics and eco-efficiency comparing with the conventional process. This innovative technology for integrated process of oxidized nickel ores was patented in Russia.INTRODUCTION Development and industrial implementation of efficient technologies to process oxidized nickel ores is a very important task for non-ferrous metallurgy of Russia. The main reasons for the required technical upgrade of the plants processing oxidized nickel ores is depletion of rich ores, increase of energy resources costs, amplification of environmental and production standards. Due to this, transition from conventional pyrometallurgy to cost-effective hydrometallurgical technologies of ore liberation and solutions processing is logical and corresponds to the worldwide practice of Ni production from oxidized nickel ores."

Jan 1, 2018

By Sanggono Adisasmito

"The quality of the higher education in Indonesia is being improved by implementing a program financed by the World Bank under a project named QUE (Quality for Undergraduate Education). The investments are provided to selected study programs through a competitive selection process. The grant finances staff development, the purchase of equipments, textbooks, consumables, technical assistance, and incentives for outstanding faculties such as teaching grants, project grants, lecture note awards, and educational policy studies. These additional investments are provided to produce chemical engineering graduates that will compete beyond the national market.Chemical Engineering Department of Institut Teknologi Bandung in Indonesia has been selected to receive the QUE grant beginning the year 2000 and ending the year 2004. The department is actively involved in the mineral processing issues, particularly in the aspects of energy supply and the environmental protection. The activities are distributed in different laboratories and areas of expertise, such as: thermodynamics and utility systems, process equipment, chemical reaction and catalysis, microbiology and bioprocess engineering, process control, ceramics, as well as polymer and membrane technology. The main objectives of the QUE project are to improve the undergraduate program in the following aspects: Relevance, Academic atmosphere, Institutional management and commitment, Sustainability, as well as Efficiency and productivity, or abbreviated as RAISE. At the end of every fiscal year, the progress of the program is evaluated to measure the effectiveness of the project.The achievement of the QUE project objectives were assessed using performance indicators developed during the program design. There are six indicators to measure the performance of the individual program of study, such as: (1) Admission Test score, (2) average students' Grade Point Average (GPA), (3) average graduates' length of study, (4) graduates' waiting time before getting first job, (5) Test of English as Foreign Language (TOEFL) score, (6) Graduate Record Examination (GRE) score. Essentially, the RAISE evaluation criteria will be used to perform three main functions, such as (1) to measure the achievement through the six quantitative performance indicators, (2) to support the progress of evaluation and reporting throughout the implementation of the program, (3) to provide a universal framework for qualitative evaluation."

Jan 1, 2003

By Alan Bax, John D. Lewins

"Platinum Australia Limited (“PLA”) is currently undertaking a Feasibility Study into the development of the Panton Platinum Palladium Project located in the Kimberley region of Western Australia. The Panton Intrusive is a layered, differentiated mafic to ultramafic structurally complex body that has undergone numerous folding and faulting events. This has resulted in a southwesterly plunging synclinal structure some 10 kilometres in length and 3 kilometres wide.High grade PGM mineralisation is hosted within a number of stratiform chromitite reefs within the ultramafic sequence. The focus of the Feasibility Study is on the Top Reef which is situated approximately 150 metres below the mafic/ultramafic interface. The average true width of this reef is approximately 1.2 metres and the reef has a defined resource is 10.1 million tonnes at an average grade of 6.1 g/t PGM + Au.The Palladium to Platinum ratio of the Top Reef is approximately 1.15:1 and the reef also contains an average of 0.4 g/t Au and 0.3 g/t other PGM’s. The Panton ore is considered refractory in nature and standard flotation techniques achieve a PGM + Au recovery of less than 65% with a concentrate grade of less than 100 g/t PGM + Au. As part of the Feasibility Study Platinum Australia in conjunction with their major shareholder Lonmin Plc developed a new metallurgical process which has achieved an overall PGM + Au recovery of approximately 80% into a high grade PGM concentrate which is suitable for feeding direct to a PGM refinery.THE PANTON PROCESSThe Panton Process incorporates a two-stage Milling and Flotation circuit with no cleaning stages to produce a low grade, high recovery flotation concentrate. Typically the concentrate mass constitutes 25% of the feed and has a PGM + Au grade of 25 g/t.This low-grade concentrate is subjected to calcination in a rotary kiln or fluid bed at a temperature of approximately 400 0C for a period of 60 minutes. This step is designed to render the platinum minerals soluble in cyanide and both the temperature and the duration of calcination are critical to the efficiency of the leaching process."

Jan 1, 2003

By L. O. Filipov, N. E. Menad, A. Geneyton

"Zeta potential of synthetic monazites presenting various compositions were measured to investigate the effect of the main lanthanides substitutions on electrophoretic mobility and resulting IEP. The measurements are performed in a CO2 depleted and enriched solutions showing both reduced influence of monazite chemistry and strong influence of ions resulting from the solubilization and dissociation of CO2. The influence of oleic acid on the electrophoretic mobility of those monazites was also investigated. The influence of pH on oleate adsorption was studied using a bubble/particle adhesion system. Adhesion strength measurements were performed on pure synthetic monazite-(Ce) and monazite-(La). An extensive thermodynamic model of monazite in water was developed to highlight correlations between lanthanides hydroxides/carbonates species concentrations in the bulk solution and oleate adsorption. Based on electrophoretic measurements, advanced thermodynamic consideration and adhesion measurements, further details of the oleate adsorption model on monazite surface were proposed.INTRODUCTION Electrophoretic and potentiometric data on monazite and, a fortiori, other rare earth semi-soluble salts such as bastnaesite are extremely erratic (Chelgani et al. 2015). The isoelectric points measured with electrophoretic mobility methods range from 4.7 to 6.5 although sporadic data indicates an IEP (isoelectric point) far from that range. Different explanations are proposed in the literature to explain the IEP variability notably the numerous chemical substitutions that frequently occurred within monazite crystal lattice (Chelgani et al. 2015). Based on lanthanides speciation diagram, several authors highlighted the influence of specific lanthanide species on the flotation performance of rare earth semi-soluble salts when carboxylate or hydroxamate collectors are used. Although lanthanides ions have a great affinity for carbonates groups (Kragten et Decnop-Weever 1987), lanthanide (hydrogen) carbonates were not implemented in speciation diagrams. In this work, an advanced thermodynamic model is proposed to highlight correlation between flotation performance and lanthanide species predominance but also concentrations. Qualitative measurement of the monazite surface hydrophobicity are performed through tests of adhesion of coarse monazite particles onto bubbles. Since flotation and microflotation technics are highly influenced by hydrodynamic parameters, this method was investigated to obtain a sharp contrast between appropriate and inappropriate pH conditions. This paper is to investigate 1) the effect of lanthanides substitution on monazite surface properties through zeta potential measurements, 2) the mechanism of adsorption of carboxylates on monazite surfaces and 3) the effect of CO2 on monazite surface properties and carboxylates adsorption."

Jan 1, 2018

By Y. X. Yang

Bottom ash is a solid waste stream in a Waste-to-Energy (WTE) processing plant during the combustion of the municipal solid waste (MSW). In the Netherlands, bottom ash contains typically about 18% metals originated from the MSW, and current industrial practice could recover about 10% metals through magnetic and eddy current separators. The remaining 8% as the finer particles is difficult to recover through current physical separation technology. Among various alternatives, vitrification is one of the promising options to immobilize the ash and recover the remaining metals. During vitrification a homogeneous glassy slag and a Fe-Cu based alloy were obtained. In the cur-rent study, the metal alloy recovered from the bottom ash originated from a Dutch Waste-to-Energy plant contains about 82 wt% Fe, 12 wt% Cu and 6 wt% other alloying elements and impurities such as C, S, P, Ni etc. The generated alloy does not have direct commercial applications, and separation of copper from iron-based alloy is critical to obtain the market value of both copper and ferrous constituents. To find a suitable processing route of this metal alloy, various alternative approaches have been considered for an efficient removal of copper from the alloy, and the focus in the present study was on the sulphide treatment at elevated temperatures of 1400 ~ 1500oC. The tested sulphide systems include pure FeS, FeS containing sulphide mixture (such as Na2S and Al2S3), pyrite (FeS2) mineral, ZnS containing sludge as an industrial waste. It was found that the carbon saturation of the alloy is proved to be an essential condition for a proper phase separation. The results showed that FeS mixed with Na2S, ZnS containing sludge and pyrite are effective sulphide systems for copper removal with a removal efficiency of 92% by using pyrite and 95% by zinc sludge at a S/Cu ratio of around 7 times of the stoichiometry. The copper content drops from 12 wt% to about 2 wt%. However, it is still difficult to remove copper completely from the alloy in a single step, and a multi-step operation is needed. The present research is expected to contribute both to the utilization of the metal recovered from bottom ash, and to the general recycling of steel scrap where copper removal from the steel scrap is a critical issue.

Jan 1, 2014

By V. E. Dementiev, V. I. Kulikov, G. I. Voiloshnikov, Yu. O. Fedorov

"The report presents the summary of the JSC Irgiredmet’s activities in the field of preconcentration of ores. As of 2018, the Institute has almost 40-years’ experience in this area. Over the years, Irgiredmet has done a lot of work – from development to implementation of new technologies of ore piece sorting and concentration based on X-ray radiometric separation (XRRS). INTRODUCTION Preconcentration has been a challenging issue of the mining industry over the last decades. The implementation of this technology can significantly increase mining efficiency. The main application of preconcentration is improvement of mined ores quality, however new and more complex issues have arisen with the evolution of the technology. Irgiredmet has started to develop an efficient preconcentration technology for gold-bearing and rare-metal ores 40 years ago. The X-ray radiometric method widely used at that date as a method of elements determination in geology and geophysics become the ground for this work (1). Since that time, the Irgiredmet Institute has developed and significantly improved the technology of piece ore sorting, or XRRS (2-5), that is currently also known as the X-ray fluorescence method. The progress of the XRRS development achieved by Irgiredmet in cooperation with Rados LLC, Tekhnoros LLC (Krasnoyarsk), Rados-Service LLC and CJSC Tekhnogen (Ekaterinburg) has proved efficiency and applicability of the XRRS technology for processing a wide range of minerals and solving of various technological problems (7-9) compared to other radiometric methods (6). Furthermore, obtained results are supported by numerous studies, trials and implementations. The significance of ore preconcentration for greenfield and brownfield projects determined the establishing a new subdivision of Irgiredmet, the XRRS Technology Center (XRRS TC), that has provided the Institute with a completed range of processing technologies, from preconcentration to producing final products. Over the past few years, the XRRS Technology Center has carried out studies and testing of a numerous (more than 100) projects, mines and deposits of gold-bearing ores, rare metal ores (Be, Ta, Nb, W, Mo), base metal ores (Cu, Sb, Zn, Pb), ferrous metal ores (Fe, Ti, Cr), rough diamonds and coal. The XRRS Technology Center performs various specific studies and testing not only in Russia, but as well as in Kazakhstan, Georgia and Mongolia. Mines and companies from Chile, India, China, Iran and other countries also take an active interest in the XRRS technology."

Jan 1, 2018

By Yonghui Hu, Hongxiang Ran, Honggang Wei

"A new PVM vertical ring high-gradient high-intensity permanent magnetic separator authorized by China Invention Patent ZL201110294866.4, which featured with vertical magnetic field structure was developed to dramatically save energy consumption and running costs compared with electromagnetic separators. The specific magnetic circuit design ensures PVM separator generating high magnetic field intensity as well as solving equipment large-scaling. The newly developed industrial PVM separator has been proved suitable for recovery of weak magnetic minerals or purification of non-metallic minerals benefiting from its high background and induction magnetic field intensity up to 0.8/1.5T, stable service performance and low running costs. The first ?1.5mm PVM separator has been applied in removing iron from quartz sand in Fengyang, Anhui, and ?2mm PVM separator will be installed to separate hematite. Industrial applications and tests proved that PVM separators could gain similar separation effects and especially save more than 80% of power consumption compared with the conventional electromagnetic high-gradient high-intensity magnetic separator, which will contribute a lot for energy conservation and environmental protection. The development of high gradient magnetic separator technology has played an important role in utilizing weak magnetic minerals, which has been widely used in many mining enterprises. The main forms of high-gradient magnetic separators include both of electromagnetic high-gradient and permanent magnetic high-gradient. The vertical ring high-gradient high-intensity permanent magnetic separator features with high magnetic field gradient, large processing capacity and never clogging, which has been widely used in recovering fine weak magnetic mineral and purification of non-metallic minerals[1-3]. However, electromagnetic coils excitation needs more energy consumption, and relatively high running costs and maintenance costs as a result of the complicated cooling system. So permanent magnetization of the electromagnetic magnetic separation equipment is a very important research direction at present. With the continuous improvement of resource utilization standard and efficiency requirements, high energy consumption of the electromagnetic vertical ring magnetic separator have been highlighted, which has affected the economic benefits of mining enterprises to a certain extent. In the aspect of high-gradient high-intensity permanent magnetic separation equipment, considerable researches have been carried out at home and abroad and many small-sized prototypes were developed yet never strode into large-scale industry applications[4-6]."

Jan 1, 2018

By Buks Kruger

"After the milling and flotation of the platinum bearing ore, the flotation concentrate is electrically smelted in 6-in-line electric arc furnaces and the resulting furnace matte treated in Peirce Smith converters to remove the iron sulphide. The iron free (less than 1% Fe) converter matte is then granulated and sent to the Base Metals- and Precious Metals Refineries for further processing.During the smelting and converting processes two distinct gas streams are produced.The Peirce Smith converter off gas contains 4% - 9% SO2 which is treated in a conventional Sulphuric Acid Plant to produce sulphuric acid (H2SO4).The electric furnace off gas contains 0.9% SO2 and was (until September 2002) vented through a 91 meter high stack to atmosphere.Off gasses which contain less than 3% SO2 is difficult to handle and quite a few processes had been developed over the years to cope with this gas. A broad spectrum of process suppliers and technology approaches is available and the different technologies can be divided into a few main approaches i.e.Scrubbing of the off gas with an alkaline solution to produce an environmentally friendly and stable waste product which can be discharged onto a tailings dam or permanent landfill site.Physical absorption of the SO2 into a chemical solution to produce high quality chemically pure process chemicals.Catalytic reaction of SO2 with O2 to produce SO3 which is absorbed in water to produce sulphuric acid of less than 90% strength.In October 2002 Impala Platinum commissioned a Sulfacid Plant at its Smelter in Rustenburg which recovers the SO2 from the electric furnace off gasses into a weak sulphuric acid solution.The Sulfacid Plant technology is widely used in the paint pigment industry. This is, however, the first application of the technology on electric furnace off gas.The furnace off gasses contains flue dust which is removed in electrostatic precipitators. The gas exiting the precipitators normally still contains between 40 mg/Nm3 and 60 mg/Nm3 dust and passes through a quench-scrubber before entering the reactors. The quench-scrubber cools the electric furnace offgas down from ± 200 °C to 60 °C and act as a final dust removal stage."

Jan 1, 2003

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone (3PC), has been successfully tested in the Platinum industry for dealing with the dense Chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine Chromite component in the final product. The dense media effect caused by a high concentration of this in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size silica in the PGM carrying component material in the float feed. The fine barren particles of Chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.Data from many industrial scale tests of the 3PC have shown that three distinct products are obtained when the inner vortex finder length (LIVF) is extended to the region either above (normal classification) or below (reverse classification) the transition zone (a region were the inner and outer overflow streams are identical). Due to wear problems arising from extending the IVF deep into the cone of the cyclone, it is advantageous to use the shorter IVF. Only the normal classification results are reported here, but similar outcomes (to opposite overflow streams) were obtained for the reverse classification. The results showed notable differences in the percentage split of the plus 100µm material in the product streams, confirming that three distinct products are discharged from the 3PC. About 12% of the plus 100µm material in the feed reports to the middlings stream, 1% reports to the final product, and the remainder to the cyclone underflow.Results of silica and chrome splits to the three distinct products namely, the inner overflow (INO), the outer overflow (OUO) and the underflow (U/F) are given in Table 1. These show that the 3PC can be used to recover coarse silica through screening the middlings product - which has a high silica content. When the vortex finder ratios (ratio’s of cross-sectional areas) are carefully selected, the split of plus 100µm silica to the middlings product ranged from 2.9 to 9.6%. Large amounts of oversize silica and chrome report to cyclone underflow, explaining their high percentages in the underflow stream."

Jan 1, 2003

By G. M. Savov

Copper recovery via Solvent Extraction (SX) process is a well-known technique, which is practiced commercially for approximately 40 years. The main advantages of the SX process are: an absence of using high temperatures (not more than 50oC), complete recycling of barren solutions, very high selectivity at removal and purification of metals, metal conversion to a form, suitable for easy subsequent recovery. Despite the wide acceptance of Solvent Extraction, it does have some shortcomings, namely SX employs large quantities of volatile organic substances. This leads to huge plant ?footprint? of SX circuits. The SX is very sensitive to low temperatures and quantity of total suspended solids in feed solutions and this causes bad phase disengagement times and therefore poor process performance. And most important ? low grade solutions (with copper concentrations below 1 gram per litre) are very unattractive for treatment via Solvent Extraction process, because capital costs for SX plants are not a direct function of copper tenor in the feed. The combined process with Ion Exchange (IX) and Solvent Extraction ? further called IX/SX by IONTECH Engineering was developed. This combination eliminates SX negative characteristics shown above. The key findings of the IX/SX process are; (1) recovery of copper from pregnant leach solutions with metal concentrations, varying on a broad range; (2) can be operate effectively with very low-graded copper pregnant leach solutions; (3) the construction of large ponds for pre-filtration of the pregnant leach solutions is not necessary; (4) working with turbid solutions and solutions containing large quantities of suspended solids; (5) winter operation without troubles; (6) strongly reduces organic losses; (7) technological approach lead to plant sizes reducing. This paper reviews the main stages of the combined IX/SX process, the applications for metal recovery and introduces projects where the process is applied. Key findings of the process are also presented. A comprehensive technical comparison between processes has been carried out. This paper also evaluates the advantages of using combined IX/SX technology as a purification and separation step in copper production process, with the aim of further increasing the overall copper recovery and to ensure that a suitable copper concentration in the advanced electrolyte is achieved. The implementation of a Ion Exchange (IX) process in the classic Solvent Extraction-Electrowinning process(SX/EW) is found to be beneficial for processing of pregnant leach solutions both from spent and new copper heaps and dumps, acid mine drainage and other industrial streams without any preconditioning as well as in terms of achieving improved recoveries and copper cathode quality.

Sep 1, 2012

By P. Raghavan1

Reverse froth flotation experiments were carried out in the laboratory using two different types of kaolins for the separation and removal of coloring titanoferrous impurities from cryo-filtered clay after subjecting to high shear pre-treatment. This high shear pre-treatment consists of high shear agitation of a high solids clay slurry with the dispersant (high shear dispersion, HSD) followed by high shear agitation with the collector (high shear conditioning, HSC). After this pretreatment, the slurry is diluted and reverse flotation is carried out. One sample is from, Gujarat, India (Mamuara clay, ?MC?) while the 2nd sample is from Amberg, Germany (AKW clay, ?AC?). While MC consisted of 89% particles below 2µm and analyzed 1.06% of TiO2 and 0.29% Fe2O3 and measured a brightness of 83.4 %ISO, the corresponding values for AC are 67% below 2µm, 0.3% of TiO2? 0.49% Fe2O3 and 83.4 %ISO. The flotation performance is found to be greatly influenced by the conditions of high shear treatment. Important variables are HSD intensity (rpm), HSD time, HSC intensity (rpm), HSC time, HSD/HSC time ratio, ?HSD+HSC? total time etc. Higher shear intensities favor both the impurity liberation and collection. For both clays, it could be shown that impurity removal increases as total pretreatment time (?HSD +HSC? total time) increases up to a certain limit. For MC, the HSD time was only half or less than that of HSC time, while for AC, HSD time is at least twice (or more) than HSC time which is just an opposite manifestation. This is believed to be due to the striking differences between these two clays. Most importantly, the shear frequency is found more influential than the shear rate for the overall flotation performance for both clays. Interestingly, at high shear frequencies, i.e., when a stirrer with more number of teeth on the rotor is used, the ?HSD+HSC? total time is greatly reduced. Again, increased shear frequency helps to reduce flotation time and significantly improves flotation performance. At optimum conditions, product titania reduced to 0.35% for MC whereas the same reduced to 0.13% for AC. The product of flotation of MC measured 85%ISO brightness while that of AC measured84.6%ISO thus enhancing the value of the final product. It could also be established that the high shear pre-treatment shows better flotation performance than that due to collector dosage. Keywords: high shear dispersion, high shear conditioning, titanoferrous impurities, shear rate, shear frequency, brightness, clay recovery, Mamuara clay, AKW clay

Sep 1, 2012

By H. X. Yan, J. X. Zhang, F. S. Niu

"The analysis on influencing factors of hydraulic conditions in fine hematite flocculation, such as stirring speed, stirring time and axial distance of particle size and fractal dimension of floc was investigated. Furthermore, response surface methodology(RSM) has been applied according to the Box-Benhnken center-united experimental design principle to optimize parameters of hydraulic conditions as a response index to indicate the fractal dimension of floc. The results show that when the agitation speed is 900r/min, the axial distance is 2.0cm, and the stirring time is 3.0min, the particle size reaches the maximum value of 35.44µm and the fractal dimension is 1.6594. The interaction between the axial distance and the stirring speed is highly significant, but the interaction with the stirring time is not obvious. The experimental data and model predications match well, which indicates that the established model has high accuracy and practicability. INTRODUCTION With the exhaustion of iron ore resources that are easy to be mined and the vigorous demand for iron and steel, the exploitation and utilization of fine-grained embedded iron ore resources have drawn attention from the industry and the government [1~2]. Flocculation flotation is one of the effective methods for separation and recovery of fine granular minerals. In 1975, the method was first applied and succeeded in Tilden Concentrator, USA. Flocculation and desliming became the key technology of the Tilden to raise its annual treatment capacity from 4 million tons to 8 million tons at that time [3 ~ 4]. In 2008, the selective flocculation and desliming-reverse flotation technology was successfully used to treat 2.8 million tons of Qidong iron ore. Under the conditions of 28.36% raw iron grade and 98% grinding fineness -0.038 mm, the ideal index of 62.5% iron concentrate grade and 68% recovery was obtained [5]. Dr Kitchenner of the Royal College of Mining and the Ore Processing Research Group of Wallenstein Laboratory first proposed the use of flocculation to separate minerals. After that, many scholars conducted a great deal of theoretical and practical researches, but mostly they focused on chemical theories, mathematical models and selectivity differences in the flocculation process, while the research on the influence of the pulp flow state on the separation effect in the flocculation process started later [6~9]. The results show that the motion of the agitated flow field has a significant influence on the formation of flocs. The fluid morphology will change with the change of hydraulic conditions. The change of fluid morphology will not only affect the movement behavior of particles, but also change the action of chemical agents on the surface of mineral particles[10~12]."

Jan 1, 2018