Search Documents

By S. Banisi

Thickening is the most widely applied dewatering technique in mineral processing. Thickeners are used to increase the concentration of suspension by sedimentation, accompanied by the formation of a clear liquid. As the particles get finer the thickening process encounters difficulty due to a significant change in the settling behaviour of particles. The batch settling tests of coal refuse of a coal washing plant which contained 91% particles smaller than 38µm and 0.6% coarser than 75 µm showed that the optimum feed percent solids that provided highest flux (solids handling capacity) was 4%. The flux of the pulp with the plant solids concentration (i.e., 10%) was 60% lower than that of the pulp with 4% solids. A thickener with a diameter of 22m based on the dilution of feed from solids concentration of 10% to 4% was designed. Monitoring of the thickener performance for a period of one month in the plant indicated that on average the feedrate of 25t/h (dry solids) with solids concentration of 10% could be thickened to the underflow concentration of 26.5% with a clear water overflow. It was found that the key component of the successful operation of the thickener is the dilution of the feed without which the overflow loses its clarity and the system ceases to operate under predetermined conditions. Specially designed feeding system which efficiently dissipated the energy of the incoming flow and staged flocculant addition regime are among the main contributing factors in making the design and operation of such thickener possible.

Jan 1, 2014

Calcium sulfate whiskers are considered to be a prosperous reinforced material in application due to their high mechanical properties. But the hydration occurs easily at moist atmosphere or in aqueous solution. The surface topographies of the calcium sulfate hemihydrate whiskers and the hydrates were analyzed by on-line observation and using XRD. The results indicated the transformation of the crystal type and shape of calcium sulfate hemihydrate whiskers and the reduction of whiskers? aspect ratio. The hydration process of the calcium sulfate hemihydrate whiskers and the effective parameters were further discussed based on FT-IR measurements. The conclusions were obtained that the hydration of calcium sulfate hemihydrate whiskers can be divided into the three phases, namely, initial hemihydration phase, dehydration phase, and coarsening, dissolving and the re-formation of calcium sulfate dehydrate crystal phase. In addition, it was found that in the hydration process of calcium sulfate hemihydrate whiskers the calcium sulfate dihydrate whiskers are formed at first and then converted into the calcium sulfate dihydrate with different crystal shapes, but in the hydration of gypsum hemihydrate the gypsum dihydrate is formed without transition products. The surface active site-calcium ion which has strong trend to react with H2O, the surface ?OH and the inner channels are considered to play important roles in the hydration process of calcium sulfate hemihydrate whiskers.

Jan 1, 2014

By Carina Ulsen

The existing construction and demolition (C and D) waste recycling technologies and standards have been essentially focused on the production and use of coarse recycled aggregates. Very few papers focus on the production of recycled sand, although some previous results show that fine aggregates fraction represents around 40 to 60% (in mass) of the Brazilian waste and it is usually used as road sub-base or disposed in landfills. The quality of the recycled aggregate is strictly related to the content of porous and low strength phases, mainly the patches of cement remaining on recycled aggregate surface. Some technologies have already been described in the literature, even though, to the moment none of these technologies has clearly succeeded in reaching the large market available. This paper presents a summary of the main properties of the sand produced from C and D waste by tertiary crushing at vertical shaft impact crusher (VSI). Additionally mineral processing technologies were applied on the attained product, such as gravity concentration by shaking table and spirals and removal of cement paste by attrition. The main properties of recycled sand are discussed and compared to the previous C and D waste, respectively: particle size distribution, particle shape, chemical composition, cement paste content and porosity. The results demonstrates that the crushing allowed producing a VSI-sand with low porosity and water absorption due to the increasing on the content of silicates from natural rock phases and increasing liberation between these phases and porous cement paste; the particles from the attained product presented also a better shape (sphericity and aspect ratio). The attrition tests assayed on VSI recycled fine aggregates accomplished a further selective disaggregation of cement paste and other porous materials - the porosity was reduced from 10% to 7%. The concentration by shaking table at narrow sieve fractions led to a product with low porosity and reduced content of cement paste, however, concentration on spirals did not succeed since separation was performed essentially by the size of the particles. The heavy product from shaking table represented almost 75% in weight and has less than 60% recovery of CaO+LOI, and expressive reduction on porosity. The aim of producing sand from construction and demolition waste through mineral processing unit operations changes the recycling approach and contributes for up cycling the recycled sand. The exhaustion of sand deposits on Brazilian large centers, the increasing price and the construction boom encourages the development of alternative materials as construction raw material. Keywords: recycled sand, construction and demolition waste, technological characterization

Sep 1, 2012

By Chao Li, Kym Runge, Saeed Farrokhpay, Dee Bradshaw

"It is well known that froth phase has a controlling influence on the overall flotation performance. Froth recovery is expected to be affected by froth transportation behaviour. The latter has been represented by different volume balance and energy balance based models. In froth transportation models based on a volume balance, the froth phase is divided into different zones. The total froth residence time is the sum of the time spent in each zone and is dependent on the cell geometry, bubble burst rate and the position that bubbles enter into the froth phase. Alternatively, the froth transportation model based on an energy balance treats the froth phase as a block. In this model, froth height above the concentrate lip is being predicted by minimising the energy of the system which is dependent on the froth geometry, froth stability and froth rheology. The froth height can be used to calculate the froth efficiency of delivering mineralized bubbles from the pulp to the concentrate lip. This paper critically analyses the current models of froth transportation in flotation, and examines the limitations of these models. The importance of froth rheology, which is the resistance to the froth flow towards the discharging weir, in determining froth transportation, is also highlighted."

Jan 1, 2014

By B. Csoke

The Bond and the Hardgrove methods are widely used for the determination of the material?s grindability. Generally, the determination of the Bond work index of inhomogeneous materials can be carried out with high deviation using the conventional apparatuses and methods, because of the highly different grindability of components. This is more significant when the composite cement?s grindability is measured, which highly affects the design and operation of cement grinding mills. A possible solution can be the combined application of the Bond-method with the determination of the component?s weight ratio in the product and perform the Bond measurement until the steady state conditions of grindability coefficient (G) and chemical composition of the components are reached. To prove the applicability of the above mentioned idea systematic Bond and Hardgrove grindability tests were carried out of two phase composite materials. The experimental results showed that the application of the combined procedure is proven in order to have a more accurate and reliable calculation of the Bond work index of composite materials, especially when the components have significant difference in the grindability and concentration. The measurements also showed the possibilities and limits of the grindability test methods.

Sep 1, 2012

By Luís Marcelo Tavares, Marko Hilden, Malcolm Powell, Grant Ballantyne, Lian Liu

The t10 relationship developed by Narayanan and Whiten has underpinned a number of the JKMRC models and the characterisation of ore competence through impact testing with the drop weight tester. This usefulness is based on a consistent relationship between the t10 value and the overall size distribution that was noted for brittle rocks. However, like all characterisation tests this should be used only when the controlling conditions apply, which in this case is single impact breakage between two metal platens and within the range of sizes in which fragment sizes are normalizable. For any other mode of breakage the relationship should be confirmed before being applied. Soft ores or bimodal ores with widely different competence between dominant components have non-typical breakage signatures. Breakage via single point impact abrasion, compressed-bed breakage, low-energy surface breakage and incremental breakage, to name some of the other breakage modes, do not obey the general t10 relationship, so their outcomes cannot be used to provide a direct comparison. Inappropriate use of the t10 parameter can result in misleading conclusions about efficiency of energy use. These issues and alternative comparison techniques are presented and discussed in terms of choosing appropriate measures of efficiency of breakage, ore competence and energy required for comminution.

Jan 1, 2014

By Vitaly Kretov, Valery Golikov, Vladimir Ryaboy, Elena Shepeta

"The aim of the study was to develop and implement more efficient dialkyldithiophosphate collectors. A hypothesis has been formulated on the action of dialkyldithiophosphates in the flotation of sulphide ores based on the assessment of their complexing properties and surface activity at the liquid-gas border. Dialkyldithiophosphates form weaker complexes with cations of heavy metals compared to xanthates, and are characterized by a large difference in the strength of their complexes with heavy metal cations. It provides higher selectivity of dialkyldithiophosphates in the separation of non-ferrous metal sulphides and iron sulphides from them. To make a quality assessment of the impact of surface activity of the synthesized collectors on their selectivity of action and collecting power, an assessment of the surface tension of their aqueous solutions has been performed using the stalagmometer method. It is well known that a stronger collector is characterized by a greater surface activity, in contrast to a more selective collector which is characterized by a lower surface activity. Based on studies, new dialkyldithiophosphate collectors BTF 163 and BTF 1552 are suggested for use in the flotation of sulphides to increase the recovery of copper, gold and silver. The collector BTF 163 was introduced at a gold processing plant in Kazakhstan and has been undergoing industrial testing in the sulphide cycle of scheelite-skarn-sulphide ores in a factory in the far east of Russia. The collector BTF 1552, which increases the recovery of silver and gold by 3%, was approved for industrial testing in another far-eastern factory. A modification of the reagent BTF 1552, the new reagent BTF 1522, was introduced in the flotation of copper-zinc ore at a factory in Kazakhstan."

Jan 1, 2014

By Victor Avdokhin, Ivan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation.Catching coat is formed of natural magnetic and weak-magnetic placer minerals in field of magnetic system of the sluice. Magnetic minerals, placing along magnetic lines of force, form rough coat of fluffy structure. Size of the magnetic particles is chosen taking into account expected size of gold particles, which are to be fixed on the rough coat or between the magnetic particles. Changing coarseness of particles of mineral bed allows to regulate selectivity of recovering heavy minerals.Forming artificial fleece from magnetic minerals of initial sand, increasing capacity of the bed and relative hydraulic proportionality of mineral particles of the bed provide for the most effective recovery of fine gold."

Jan 1, 2003

By D. Renda

With thise Process of obtaining a solid fuel which is both ecological clean and has a high calorific value by a two-stage method of enriching preferably type lignitic coals to remove a high content of all sulphurs, incuding organic sulphur, which method comprises converting the coal to a semi-coke from followed by magnetic separation. In the Experiments given the best results the washed lignite coal in the West-Turkey, Tavsanli- Region, size -3.35 mm on dry basis. In the microscopic studies of the brigh-thin cross-section taken from the samples of sulfur min-erals pyrite in the dimension of 2~50 micrometers and melnicovite 10 micrometers particles. An thermal treatment an semi-coking themperature between 370°C to 650°C give the best Result of 480 °C. The oxidation and decomposition of sulphur minerals pyrite and melnicovite in lignite coal proceed the iron oxides Fe2O3 and pyrrhotite FeS on the surface layer. The Magnetic Seperator (Rare Earth Magnetic Separator, REMS) is capable this two form of sulphur, including organic and inorganic sulphur, in semi-coke and resulted in the magnetic-fraction in REMS. The non-magnetic-fraction remove total sulphur by 68 %, ash by 44 % and increase the upper calorific value in 15 %. The clean lignitic coal can be utilized in human or energy power stations.

Jan 1, 2014

By Lev Filippov, Lorène Dessalas, Inna Filippova, Yves Foucquet

"Seafloor massive sulphide (SMS) deposits, similar in composition and genesis to terrestrial volcanogenic massive sulphide deposits, are generally found in volcanic seafloor environments along major rifts and mid-ocean ridges. Theyare associated to extensional tectonic settings such as nascent-arc, rifted-arc and back-arc environments. They may represent important source of base metals and be an alternative to on-land resources. Seafloor massive sulphide deposits have particular mineralogical compositions and textural features differentiating them from terrestrial one. When extracted from salty water and exposed to the ambient air, massive sulphide samples strongly oxidize and soon become covered by thin layers of iron, copper and zinc rich sulphates and oxides, as well as elemental sulphur. The textural properties vary according to the degree of maturity and the sample position within the hydrothermal deposit. The total porosity of that type of samples is also relatively high, especially for immature samples such as black smoker chimneys, which can reach 15% of total porosity. Because the secondary mineralization and porosity level are different, seafloor massive sulphides ores respond differently from terrestrial ore to processing methods. Froth flotation, commonly applied to separate all type of sulphides from the gangue, is one possible technique for processing seafloor ore. Sulphide recovery rate is, in most cases, excellent (>90%) however separation of the various mineral phases is difficult to obtain even when applying known methods used for terrestrial ore. Moreover, the flotation behaviour decreases drastically with the time of conservation at the surface, even when the samples were stored in a confined environment. High pH values, which is a good way to depress pyrite and therefore to favour the flotation of copper and zinc sulphides, do not have the same effect on seafloor ore. Consequently, careful flotation procedure must be elaborated to obtain efficient mineral separation technique for this specific marine ores."

Jan 1, 2014

By V. I. Lakshmanan

The growing concerns on process efficiency, escalating operating and capital costs along with environmental and social concerns of using conventional technology for extracting gold and titanium dioxide demand an in-depth understanding of the fundamentals and a broader understanding of the various process steps involved. This will allow development of efficient process flowsheet for product recovery and compliance with regulatory guidelines. This paper will discuss our recent developments in mineral processing and hydrometallurgical technologies to recover gold and titanium dioxide from a wide range of feed materials including ores, concentrates and tailings.

Sep 1, 2012

Nowadays, the more successful plants are those who have adopted effective and efficient strategies to optimise their plant operation. As the ?heart of the plant? could be viewed as the mil-ling/grinding area, one of the key steps in plant optimisation is, therefore, ensuring the mill is operating properly. In the past, when primary, secondary and tertiary crushers fed material directly to large ball mills, the energy efficiency of the concentrator was determined for the most part by the ball mill operation, whereas now the energy efficiency of a plant often rests largely on the semiau-togenous grinding (SAG) mill operation. As a result, mines have shifted their emphasis in optimization from ball mills to SAG mills. The grinding mill?s energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of pulp lifter being to transport the broken material and slurry out of the mill, its design optimization therefore affects the discharge capacity (or mill throughput) of AG and SAG grinding mills. This paper will discuss how the optimised design of the pulp lifter/ discharger has helped to eliminate material transport issues such as flow-back and carry-over of slurry and pebbles to in-crease the energy efficiency of SAG mill using the actual operational data.

Jan 1, 2014

By P. Gao, J. W. Yu

"Magnetizing roasting-magnetic separation is an important route for the beneficiation of refractory iron ores. In this investigation, a pilot-scale fluidized magnetizing roasting reactor was introduced and used to study the effects of roasting temperature and the flow rates of reducing gas CO and fluidizing gas N2, on the magnetizing roasting performance of an Anshan-type carbonate-bearing fine iron ore. The results showed that the hematite was almost reduced to magnetite by a gas mixture of 4 m3/h CO and 1 m3/h N2 at a roasting temperature of 540 °C. Under the optimized conditions, a high-grade magnetic concentrate assaying 66.1 wt.% Fe with a recovery rate of 91.2% was achieved from an Anshan-type carbonate-bearing fine iron ore assaying 42.0 wt.% Fe. The XRD, VSM, and optical microscopy analyses revealed that the siderite was successfully converted to magnetite by roasting. Some coarse hematite particles were difficult to reduce to magnetite completely; however, these generated magnetite particles with a fine hematite core could also be effectively recovered by magnetic separation after liberation from gangue minerals due to their strong magnetism. INTRODUCTION Magnetizing roasting followed by low-intensity magnetic separation has been considered as an effective solution, both technologically and economically, when upgrading refractory iron ores (Zhang et al., 2012; Peng et al., 2012; Li and Zhu, 2012). According to the type of roasting reactor, the magnetization roasting can be divided into shaft furnace roasting, rotary kiln roasting, and fluidized bed roasting (Zhu and Li, 2014).Shaft furnace magnetization roasting system is mainly composed of heating and reduction processes. The hematite ore is first heated to 700~800 °C in the heating zone, then falls into reduction zone where the weakly magnetic hematite is reduced to magnetite by coke oven gas at 550~600 °C (Yan et al., 2012). However, several years of engineering practices indicate that the shaft furnace can only process the hematite ores with a granularity of 15 ~75 mm, and the shaft furnace roasting is also characterized by heterogeneity of roasted product. Hence, the shaft furnace magnetization roasting technology is gradually replaced by high-gradient magnetic separation with the development of high-gradient magnetic separator. The rotary kiln generally handles the hematite ores with a grain size of less than 30 mm (Zhu and Li, 2014), however the formation of clinker ring in the rotary kiln will affect the yield of iron resource. In the fluidized bed furnace, the hematite ore is shaken up by an upward current of gas which maintains the individual particles in suspension (Yu et al., 2018). The precise adjustment of the gas velocity to the particle size and the specific weight of the hematite ore, make it possible to generate a floating mixture of gas and solids which behaves almost like a liquid (Yu et al., 2017a). The process is reported to have the following advantages over the other roasting techniques: ease of control due to absence of moving parts within the reactor, homogeneity of roasted products, ability to handle fine particles, and high efficiency of heat transfer and mass transfer (Li et al., 2015; Yu et al., 2017b). However, the simultaneous heating and reductive magnetization of hematite ore occur at the same place in the conventional fluidized bed reactor. Therefore, the reductive atmosphere, as well as the safety and stability of anti-explosion are hard to be controlled. Besides, the roasting temperature for conventional fluidized bed furnace is usually up to 950~1150 °C (Liu et al., 2017). Thus, the formation of clinker ring caused by high temperature will affect the operating efficiency."

Jan 1, 2018

By H. Lieberwirth, M. Hesse

"Selective comminution (SC) is beneficial for the treatment of primary raw materials, especially if it is utilized in the pre-concentration process. Pre-concentration processes are applied in mineral processing to relieve subsequent processes and to achieve a higher efficiency. SC is also a promising method for the treatment of low-grade ores and waste dumps. With SC, various components can be separated such as valuable minerals from waste, ore from wall rock and different ore varieties within a deposit. SC is a property of a comminution system and leads either to a preferred crack propagation in one component (called preferential breakage) or to a preferred crack propagation along the grain boundaries (called interfacial breakage). SC results from different comminution behavior of various components in the feed material. For mechanical comminution, the preferential breakage seems to be the most important case of SC. Hereby SC generates only the difference in the particle size which can finally be used as a sorting parameter. A sorting process which uses SC depends on three parts: the feed material, the comminution machine and the separation machine. The feed material defines the potential for SC. Differences in properties like strength, toughness and density which are related to comminution are often used. The comminution machine has to exploit this potential. The extent of the exploitation can be influenced by the machine design, material and operational parameters. After SC, the various components are still combined in the product. So ultimately, a separation machine is needed. At preferential breakage, a simple screening machine can be used. The basics about SC will be presented at first. This contains relationships between material properties, the kind of loading in the comminution machine and the SC effect. These basics can be used for example to exploit a potential to SC for a pre-concentration step or to avoid the SC for a higher efficiency of subsequent processes. Based on recent investigations with impact load, the influence of the important parameters compressive strength, density, particle size and impact velocity to the SC will be shown, using examples of lead-zinc ore comminution and fluorspar processing."

Jan 1, 2018

By M. Roy

Coke combustion during sintering process is significantly governed by coke breeze size distribution, which in turn affect sinter quality i.e. sinter granulometry, Tumbler index, Reduction Degradation Index and Reducibility Index of sinter. To know the effect of microfines of coke breeze on sintering process parameters, pot sintering tests were conducted and it was found that when microfines are eliminated and optimum coke size (1-3mm) is used yield of sinter increased by more than 7%. Similarly productivity increased by 9%, the strength of sinter i.e. ISO Tumbler Index increased by 2.3% and +10mm sinter size increased by 5.5%. Controlling of microfines during crushing and by improving crushing index will result in improved quality and productivity of sinter with lesser amount of coke breeze. This paper describes that how to optimize solid fuel i.e. coke breeze consumption in sintering process through granulometry control. Keywords: iron ore sintering, coke breeze granulometry, productivity of sinter, quality of sinter

Sep 1, 2012

By Q. Cui, Z. G. Song, S. S. Lin, S. Q. Li, S. S. Lu, G. B. Zheng, A. J. Ren

"Mine tailings is one of the most important bulk industrial solid wastes, but its rate of comprehensive utilization is relatively low. Efficient separation, recovery and utilization of the valuable components is one focus of the comprehensive utilization of tailings. Beneficiation recovery of the valuable minerals is the most direct comprehensive utilization method for tailings. There are generally different kinds of nonmetallic minerals contained in the nonferrous metal mine tailings, which are secondary mineral resources waiting for further developing and recovery. Comprehensive utilization test studies on fluorite in tungsten beneficiation tailings and feldspar in molybdenum beneficiation tailings have been carried out by author and good test results are achieved. Some of the technologies developed in the test study have been applied in industrial productions, which have been working well. The economic, social and environmental benefits are remarkable. Our test studies and some production practices will be summarized and current situation and existing problems of comprehensive utilization for nonferrous metal mine tailings will also be discussed. Assumption and prospect for the future study on comprehensive utilization of nonferrous metal mine tailings will be brought at last.INTRODUCTION Mine tailings is one of the most important bulk industrial solid wastes, but its rate of comprehensive utilization is relatively low. Efficient separation, recovery and utilization of the valuable components is one focus of the comprehensive utilization of tailings. Beneficiation recovery of the valuable minerals is the most direct comprehensive utilization method for tailings. There are generally different kinds of nonmetallic minerals contained in the nonferrous metal mine tailings, which are secondary mineral resources waiting for further developing and recovery. Comprehensive utilization of nonmetallic minerals of nonferrous metal mine tailings not only can improve the value of the ore but also reduce the stock of tailings, being the key to reduce emissions at source for exploitation of nonferrous mineral resources (Cai, Yang, 2000)."

Jan 1, 2018

By Rakesh Kumar, S. Mehrotra, T. Alex

"This paper, an overview of our recent findings on mechanical activation (MA) of minerals/materials, emphasizes the importance of sample genesis, mechanically induced/altered porosity and surface area, mineral interactions, glassy inorganic materials, surface alteration and zeta potential changes and, mechanically induced reactivity of solids. Materials investigated include Al-oxyhydroxides (gibbsite and boehmite), fly ash and granulated blast furnace slag. Planetary, attrition, vibratory and conventional ball mills are used for MA. Genesis of boehmite has been found to have a bearing on its behavior during MA. For example, BET specific surface area (SSA) of boehmite prepared by thermal dehydroxylation of gibbsite has decreased from 265 to 65 m2/g during 240 min of MA; in contrast, the SSA of hydrothermal boehmite has increased from ~2 to 36 m2/g. Mechanisms of surface area changes in the two boehmite samples differing in their genesis is explored. MA of gibbsite and its mixture with hematite/quartz using attrition milling has indicated that the presence of the second phase promotes amorphisation. Amorphous materials show signs of change in nature of bonding during milling as illustrated by MA of fly ash. Physicochemical changes during MA are not restricted to the bulk phase. The genesis of zeta potential changes in MA solids can be many; for example texture induced zeta potential changes as observed for gibbsite, while zeta potential changes during the milling of granulated blast furnace slag occur due to enhanced (possibly non-congruent) dissolution. Interesting manifestations of mechanically induced reactivity and its correlation with physicochemical changes are illustrated in terms of alkali leaching of boehmite and, hydration of MA slag. New findings reported here are associated with several open questions and are highlighted in the paper."

Jan 1, 2014

By Anand Anupam

Conventionally, beneficiation in Indian coal washeries is done using dense medium cyclones upto the size of 0.5 mm. Coal fines below 0.5 mm size are extensively cleaned by froth flotation. There are many problems associated with flotation of Indian coals, e.g. poor response of coal particles to flotation, misplacement of fine high-ash material to froth, loss of good quality coarser coals (within ?0.5 mm size range) to tailing streams, high cost of reagents, water contamination, etc. In addition, sophisticated control systems for efficient management of the fines washing circuits are needed. Thus, there is an escalation in the capital and processing costs. In view of these facts, studies were carried out to establish the cleaning potential of dense medium cyclones for beneficiation of fine coal down to a size of 0.1 mm, essentially aimed at reducing the load on fine coal circuits mainly comprising of flotation. ROM Coal (in the size range of -2 + 0.1 mm) obtained from JogtaOCM,Jharia coalfield possessing relatively low ash (about 21%) was used in this study. Purpose for using low ash coal was to further lower, its ash content down to 8% which is comparable, to the ash content of imported coal. After characterization studies, nine tests were carried out on the prepared feed sample for its beneficiation using a dense medium cyclone of non-conventional design (very low cone angle and longer barrel), by varying its apex and vortex finder diameters. The efficiency of separation has been evaluated using Tromp curves. It could be established that it is possible to produce a clean coal of 8% ash, with Ep value of 0.044, using Jogta OCM coal by treating it in a modified dense medium cyclone. These results are summarized and discussed in detail in the present paper. Keywords: dense medium, cyclone, fine coal, beneficiation, Jharia coal

Sep 1, 2012

By C. A. Acuña

Extensive literature exists on the motion of single bubbles and the behaviour of swarms of bubbles. This contribution describes work to track and reveal the motion of individual bubbles in a swarm. The technique is based on high speed cinematography and tracking of multiple moving objects. Image processing algorithms were implemented in Matlab to isolate and measure geometric proper-ties of the bubbles in image sequences recorded at 2 ms interval; and these properties were compiled into a data structure. To track a bubble, the geometric properties and a matching criterion were applied on consecutive pictures to identify the bubble. The bubble trajectory was reconstructed from the data structure for the matched objects. The methodology is briefly described. The new technique was tested for bubbles produced at slot-type spargers (i.e., approximately 2-D swarms) in the presence of two frother types ('strong' and 'weak'). Two observations are discussed: a) that bubble motion in a swarm describes a velocity-size relationship dictated by the dominant bubble size class; and b) that surfactant type influences bubble rise velocity for bubbles in the range 0.1 mm to 4 mm. The latter suggests surface viscosity rather than surface immobilization determines bubble rise velocity.

Jan 1, 2014

By M. Ranjbar, M. Khosravi Rad, A. Tohry

"The filling degree is defined as the volume ratio of the load inside the mill, which determines the power drawn from the motor, as long as the filling degree is not more than the optimum level. As the filling degree increases beyond the optimum level, the impact energy inside the mill will decrease and as a consequent, the mill power output will also decrease. Therefore, the mill filling degree is a key parameter in evaluating the grinding circuit performance, as it determines the mill reaction to the input feed. Since this parameter has an impact on the mill capacity, measuring the mill load is vital for control and optimization of grinding process. As in Choghart Processing Plant no instrument is available to measure the AG mill filling degree, an empirical model based on the bearing-oil pressure is proposed. The AG mill filling degree was related to the differences between the average pressure of input and output bearings, the circulating load and power drawn. It was shown that a quadratic model could relate the mill filling to the above mentioned measurements. This model showed that when the power drawn and circulating load decreases the bearing-oil pressure needs to be checked. If the bearing-oil pressure increases the feed rate needs to be decreased and steel ball be charged to the mill to increase the grinding and prevent mill overloading. INTRODUCTION The feed quality (size and hardness) affects the grinding process in AG mills. Reducing the top feed size and increasing the ore hardness reduce the mill efficiency and increase the particles with critical dimensions inside the mill. These will result in increasing the mill filling degree and reducing the mill throughput and efficiency (Wills and Finch, 2015). The volume ratio of the load inside the mill is called filling degree, which determines the mill power drawn. It is believed that if more energy is mainly spent on grinding (Wills and Finch, 2015). Therefore the mill power draw is used as a mean to control the mill efficiency."

Jan 1, 2018