Search Documents

By Teja Reddy, Narasimha Mangadoddy, Mandakini Padhi

"In mineral comminution circuits, the feed to hydrocyclone consists of a heterogeneous mixture having varied degrees of liberation and sizes leading to the multi-component particle system. The presence of multicomponent particles exhibits a significant change in the classification performance parameters. In this work, a numerical study is conducted with an artificial mixture of magnetite and silica of different proportions having similar particle size distribution to understand the multicomponent interaction in a laboratory scale hydrocyclone. The heterogeneous feed is injected tangentially would attain different settling rates under the influence of centrifugal, drag and turbulent dispersion forces. In this work, Large Eddy Simulation (LES) is used to resolve the continuous phase turbulence. Modified Algebraic Slip Mixture (ASM) model using the corrected Newtonian rheology of fines to simulate multi-density and multi-size particles of the mixture in a hydrocyclone. The influence of the multi-component particles on classification performance is extracted from the simulation in terms of the performance curve, i.e. recovery to underflow, volume fraction distribution and the key forces acting on each particle in the mixture. An interaction was observed between different components during the classification process, featuring accumulation of heavier particle at wall-side pushing the lighter particles into the inner locus of zero vertical velocity (LZVV) zone. The comparison of separation factors of different size particles presented the higher probability of the magnetite of same size reporting to wall region and hence to underflow. Hence, an increased component cut-size with the increased magnetite proportion, particularly a profound effect on lighter density component’s cut-size was observed. INTRODUCTION The multicomponent existence is found in naturally occurring ores, affecting the pure metal extraction, nonetheless also affects the comminution and classification processes. Among many another classifier, hydrocyclone is a vital equipment used vastly in many industries. The main advantages over other classifiers are a static body, low operating cost and maintenance, high throughput, low floor space requirement etc. A typical hydrocyclone consists of a cylindrical section with a central tube connected to a conical section with a discharge tube. The fluid is injected tangentially into hydrocyclone causes swirling and thus generates centrifugal force within the device. The multiphase interaction inside the hydrocyclone is extremely complex and mostly explained by theories based on hypothesis. In past years, many theoretical models were proposed like a balanced orbital model (Criner, 1950), the residence time model (Reitema, 1961) etc. Though these models give an estimation of the cut-size and other performance parameters, it cannot predict the accurate performance of the actual state of operation. Among these models, the balanced orbital theory is the most adapted concept, based on the force balances of the particle in the dual vortex flow of hydrocyclone. The finer particle is subjected to the inward drag force, generated from the outer vortex flow to the air core, and drags the particle towards the overflow. The larger particle with the higher mass have enhanced centrifugal force and falls into primary vortex near wall reporting to the underflow. Generally, the forces acting on the particle include the drag force, centrifugal force, pressure gradient force, added mass force, Saffman lift force, Magnus force and basset force (Kraipech, 2005). The major forces like a drag, centrifugal, pressure gradient are the function of the particle properties like the size and the density. Hence, the existence of the multi-size and the multi-density particle will affect the separation phenomenon, with the varied forces acting on it. The understanding of the multicomponent classification effect using ores has been only explored in few studi"

Jan 1, 2018

By Agnieszka Surowiak, Tomasz Niedoba

The paper presents a way of determining relations between ash content in coal, particle size and particle density by means of regression, multidimensional Morgenstern distribution functions and kernel approximation. The three-dimensional random vector (D, ?, ?), where D is a random variable describing particle size, ? - random variable describing particle density and ? - random variable describing ash content, where function ?=?(d, ?) is obtained by means of regressive function. The multidimensional Morgenstern distribution functions and kernel estimators with the use of Gauss function were applied to approximate the functions f(d, ?, ?) and f1(d, ?). This approach is a new way of multidimensional description of grained materials such as coal and it also allows to evaluate material features more properly than the classical statistical approach. The results were verified statistically.

Jan 1, 2014

By Z. G. Song

As a kind of complex physicochemical process, grinding would affect the subsequent mineral processing such as flotation considerably. In this study, the effect of wet grinding on malachite and calcite flotation using sodium oleate as collector was studied. And the mechanism of the effect of grinding was investigated. Laboratory scale grinding and flotation testing of malachite and calcite samples were performed. Different grinding media were used, including steel balls and zirconia balls. It was the aim of this work to study the effect of grinding on the pulp chemistry paying particular attention to flotation recovery. The effect of grinding media and different addition location of sodium oleate on malachite and calcite flotation was studied. The methodology used in this project involved grinding the ore with and without the addition of sodium oleate in mill, measuring the pH and metal ions produced by minerals after grinding, adding various quantities of sodium oleate and determining the copper recovery. The presence of species of products on the minerals after grinding was probed using X-ray photoelectron spectroscopy (XPS), and the metal ions produced by minerals after grinding were measured by atomic absorption spectrometry (AAS). It is showed that the mil-ling environments evaluated significantly affected the flotation of malachite and calcite. This study also discusses the effecting mechanism of grinding environment on floatability of malachite and calcite.

Jan 1, 2014

By D. Hatfield, G. de Jager

"The rapid developments in computer vision and computational resources are creating new possibilities for the use of machine vision systems for industrial control. A number of commercial image analysis systems exist, and research into improved measurements of froth performance is ongoing. An integral part of the implementation of these systems is the validation of the relationship between image analysis measurements and flotation cell performance. This paper discusses the factors affecting concentrate flow and presents the results obtained from one such system with respect to its ability to estimate the flow of concentrate from a flotation cell.The relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell was investigated on two industrial operations, both processing PGM (Platinum Group Metal) bearing ores. Results are presented that show a relationship between froth flow speed and concentrate yield."

Jan 1, 2003

By B. A. Kutlin, S. A. Ropeyko, N. A. Yurlova

"The aim of NPO RIVS research and practice activities is to minimize impact of the mineral processing plants (MPP) on environment by using new concentration methods, high-technology equipment, implementation of engineering solutions directed to reduce emission of polluting substances (PS) into atmosphere, application of low-waste technologies, decrease of water withdrawal from a surface water or groundwater source for process needs. In our studies environmental safety of mineral flotation is provided through technologies using highly selective chemicals, that leads not only to reducing reagent consumption, and production of saleable products of high content of extracted minerals, but also to reducing pollutant emissions, decreasing supply of surfactants (SAA) in natural geosystems, primarily, in ground and surface waters. Decrease of water withdrawal from a surface water or groundwater sources for process needs can be achieved by using closed circuits and waste water treatment for further use in process operations, recycled water conditioning to obtain optimum quality parameters for process operations of concentration. Concentration in water (wet processing), tailings dewatering and semidry and dry (filtration cake) stockpiling in tailing ponds, efficient dust-collecting systems contribute to pollutant emission reduction. Use of mineral wastes – concentration tailings as a source of valued components, facilitates efficient use of natural resources and reduces wastes and its impact on natural ecosystems due to smaller areas of damaged lands during waste products disposal. Process and engineering solutions of NPO RIVS that allow diminishing impact of MPP on natural environment (NE) have been implemented in mining and processing complexes of Russia, Kazakhstan, Ukraine, Kirghizia and Mongolia. Compliance with environmental safety requirements contributes to enhancement of mineral processing and sustainable mineral development.INTRODUCTION Mining and processing complexes have a significant impact on environment as a result of extraction and recovery of mineral resources, landscape changes, waste disposal and, as a consequence, pollution of soils, surface and underground water sources. Therefore, the aim of the operation of the mineral processing enterprises in its research and practical activities is to reduce impact on environment due to new beneficiation technologies, high-technology equipment, implementation of engineering solutions directed to reduce emissions of polluting substances (PS) into atmosphere, use of low-waste technologies, decrease of water withdrawal from a surface water or groundwater source for process needs. Compliance with the requirements of environmental safety encourages advancement of mineral processing technologies and sustainable mineral development. Concentration in water, tailings dewatering and semidry and dry (filtration cake) stockpiling in tailing ponds, efficient dust-collecting systems contribute to pollutant emission reduction. Use of mineral wastes – concentration tailings as a source of valued components, facilitates efficient use of natural resources and minimizes waste formation and its impact on natural ecosystems due to reduction of damaged land areas during waste disposal."

Jan 1, 2018

By M. Chettibi

The interaction and galena flotation with xanthenes and dexanthogen regularities have been de-fined. So, using thermodynamic method of analysis, the thermodynamic stability of [galena - xanthenes - water] system and the behavior of lead xanthenes surface state in solution were devised. Thus, results of cared out calculations and experimental investigation completely coincide with-out depending on witch product of sulfur oxidation is formed in the solution. In additional, was obtained quantitative physico-chemical models for the necessary xanthenes concentration of lead sul-fide complete flotation in the tuning fork of: at ?? values from 7.0 up to 9.0 (or at the formation of lead carbonate PbCO3 ) and at ?? values from 9.0 up to 12 (or at the formation of lead hydro carbonate Pb3(OH)2(CO3)2 Physico-chemical models derived can be used as the criteria for functional units of automation systems to control and regulate the flotation process in mineral processing plants.

Jan 1, 2014

By Francisco Cubillos, Jorge Menacho, Cesar Gomez, Juan Rodríguez

Mineral flotation is the most used process to selectively separate particles of one or more minerals of interest. The process uses natural or induced hydrophobicity to collect particles on the surface of rising bubbles through collisions and formation of bubble-particle aggregates. Flotation machines must keep particles in suspension and well distributed, while at the same time, disperse a mass of air into a population of small bubbles. The efficiency of the separation depends primarily on the characteristics of the bubble population generated in the machine and its distribution and flow throughout its volume. The formation and separation of bubble-particle aggregates create two zones, with strong interactions between them, and with markedly different hydrodynamics conditions. A model describing two-phase hydrodynamics of the continuous and dispersed phases (frother solutions and bubbles, respectively), moving along the whole unit, is proposed. Bubble populations are characterized at the formation stage including the effect of the presence of frothers. Flow through the aggregates formation zone, where bubbles move freely and are closely spherical, is modeled using drift-flux analysis. In the aggregates separation zone, bubbles initially pack maintaining a water layer thick enough to prevent capillary forces to affect their shape. As water drainage proceeds, bubbles deform, capillary channels form, and a network of channels with a diameter size distribution develops; channels become narrower (permeability is reduced) as the distance from the interface increases. Froth hydrodynamics is characterized using models originally developed to describe unsaturated flow through porous solid particle beds. Effects of hydrostatic pressure are considered.

Jan 1, 2014

By Wenqing Qin, Yunfan Wang, Ximei Luo, Fen Jiao

In order to investigate the effect of nanobubbles on adsorption of surfactant on mineral surface, the nanobubbles on the surface of calcite with -37µm fraction in the sodium oleate system were controlled by pressurization and decompression to mixing vessel. Subsequently, the adsorption amount of sodium oleate on the surface of calcite were detected by ultraviolet spectrum at different stirring times and different pressures. At the same time, the nanobubbles on the calcite surface were imaged with atomic force microscopy (AFM). In addition, a homemade vacuum Hallimond tube device was used for the flotation of single mineral, and the grade and recovery of minerals in concentrate was used to determine the influence of the nanobubbles on flotation. The experimental results showed that a large number of nanobubbles were found on the calcite surface by AFM under the dissolved oxygen difference (DOD) condition of -4 mg/L. And a large difference in adsorption capacity of sodium oleate on the surface of calcite was observed under different air pressure conditions. It indicated that the ambient pressure had a certain effect on the adsorption of sodium oleate on the calcite surface, and this effect did not depend on the constant low pressure or constant normal pressure, but depended on the changing process of pressure. The single mineral flotation experiment results indicated the recovery of calcite under decompression condition (formation condition of nanobubbles) was 1.5-2 times that under constant normal pressure, and the flotation time is much shorter. Moreover, the recovery under constant normal pressure was greatly influenced by flotation time. In this paper, only one aspect of the effect of nanobubbles on mineral flotation was preliminarily explored. It was confirmed that after vacuum-pumping, the adsorption of sodium oleate on calcite surface could be increased, the flotation time also was greatly reduced and the recovery of calcite was increased.

Jan 1, 2018

By Jan Svoboda, Atsushi Shibayama, Toyohisa Fujita, Toshio Miyazaki, Kenji Murata

"The electrical disintegration (ED) method and disintegration by underwater explosion were investigated as new fragmentation techniques for the kimberlite ore and tungsten scrap of superalloy (carbide bit). The results of various breakage tests demonstrated that both fragmentation methods as new disintegration techniques for recycling were able to liberate various components of materials of different resistivity and elastic impedance.SUMMARYThe breakage of the kimberlite ore from South Africa (sample size: 15 mm x 15 mm x 6 mm) was achieved by the ED method. A relationship between the sample size, voltage, the electrical current and the energy needed for the disintegration was found from the experimental results. Kimberlite exhibited a high degree of breakage, when the high voltage of 60 kV and the pulse current of approximately 5000 A were applied to the sample by the generator during 0.2 microseconds (Fig. 1)."

Jan 1, 2003

By M. Kargar Razi

According to the unique properties and many applications of nano silver powder, it was prepared from acid leaching tail solution. The low value residual gold and silver ions were occurred with fellow heavy metals as pollutants (Fe2+, Cu 2+and Zn2+) in acid leaching tail solution in Mouteh gold mine in Iran. Preparation of nano silver particles was achieved in two steps: first, by addition of ammonia as separation step and second by using different reagents as precipitation and extraction steps. Different controlled parameters were including pH, residence time and temperature, mixing time, and reducing reagents to metals molar ratio. Acid leaching process was carried out with sulphuric and nitric acid via suitable reductants. In order to remove copper, zinc, and silver ions from solution, all of the conditions were controlled. The optimum conditions for preparation of nano silver powder with less than 90 nm were pH 10.5, hydrazine/methanol to silver molar ratio of 3 to 4, and reduction time of 5 min in 45 °C. The results were evaluated via SEM, A.A and UV- Vis spectroscopy analytical methods.

Jan 1, 2014

By J. Faitli

The Lake Balaton is the biggest and for many reasons the most important lake in Hungary. To preserve its healthy nature it is necessary to remove the accumulated mud time to time, similarly to the many living waters, lakes and rivers everywhere. Typical existing technologies (mechanical, hydraulic) require large depositional areas, where the removed slurry and mud is dewatered through very long time. One problem is the non existence of an economical mud thickening technology. Another major problem is that current methods remove the sand fraction with the mud as well. Many times sand has to be complemented from outer sources to endanger the natural balance of the living water. By the financial support of the NKFP 3A/068/2004 Hungarian Research Project our consortium has been looking for the solution to the above mentioned problems. The original ideas of the project were: 1. Sand should be separated and returned to the water by hydrocyclon; 2. New mud thickener should be developed based on the principle that vibrating rods can force settling and packing of mud particles. The work was started by fundamental research with different samples from Lake Balaton and River Bodrog. An automated settling column (45L) has been built for the investigation of the effect of vibrating rods on the settling behavior of suspensions. An optical sensor has been developed by with the settling curve (height of settling slurry as function of time) can be automatically measured. Different vibrating methods and parameters have been tested by the application of a linear motor and mechanical eccentric drive. On the basis of the fundamental research a new thickener, called the rod ? lamella thickener has been developed and an industrial size (50m3/h) mud removing technology has been built. Main parts of the technology are the traditional dredging barge and the thickening technology. The thickening and sand separation technology is tugged by the dredging ship. Its main elements are the homogenization tank, slurry pump, hydrocyclon and the rod ? lamella thickener. In this unit lamellas carry out pre-thickening, then vibrating rods further increase the concentration. The thickened mud is transported out by a screw - of which revolution number is precisely controlled - against a spring supported valve. Paper reports about the design, building, water probe and on-site tests of this mud removing technology. Two new patents had been presented, one is about the rod ? lamella thickener and the other is about the mud removing technology with sand separation.

Jan 1, 2014

By I. N. Gridasov, T. V. Ignatova, E. V. Shelepov

"Mikhailovskoye Deposit is comprised of oxidized ferruginous quartzites among other minerals with the former widely spread across the ore field and mined along with unoxidized ferruginous quartzites. PJSC Mikhailovsky GOK strategic development is aimed at iron ore product output expansion. The most critical item of the strategic development road map is process design for separation and concentration of hematite contained in oxidized ferruginous quartzites mined as the by-product in the open pit. Laboratory and semi-industrial tests run to design cost-effective, reliable and environmentally friendly process for Mikhailovskoye deposit oxide quartzites processing included the following processes: - pilot tests of reverse anionic flotation which produced concentrate with Fe60.1-62.9% total iron content and 66-69%Fe recovery rate; - combined magnetic separation and flotation (Marubeni Company, 1982) including slime removal, reverse anionic and cationic flotation and high gradient magnetic separation resulting in 48.9% yield, Fe55-57.5%, up to Fe60.5% hematite concentration ( Fe64.1% being the best result achieved),76.2% recovery. - magnetic separation and flotation, including separation in low gradient (1400 Oe) and high gradient (up to 17000-18000 Oe) magnetic field. The results of these pilots tests were the following: 57-59%Fe concentrate, 70%Fe recovery (Mekhanobrchermet, MGOK, 1982-1988): - magnetic roasting in pilot plant of TSGOK (Krivoy Rog) which produced 61.1%Fe concentrate with 81.5% recovery. Major disadvantage of the method is high generation of dust equal to 20% of the initial feed. Based on third-party studies flotation of oxidized ferruginous quartzites process embracing best processing methods was designed by Metalloinvest Management Company LLC and PJSC Mikhailovsky GOK engineers. This paper discusses analysis of studies aimed at intensification of separation processes with application of mechanical slurry agitation (MSA), addition of alkali (NaOH) and elutriation of initial feed. The paper also provides a design solution to implement a lab-scale MSA plant. It includes feasibility evaluation of MSA inclusion in flotation of oxidized ferruginous quartzites process to enable higher yield and hematite recovery in resultant concentrate. Outcomes of the discussed work have significant value for prospective engineering of OFQ concentration process."

Jan 1, 2018

By N. Schreithofer

Varying flow regimes, particle populations and consequently different types of bubble-particle interactions characterize the different zones of a flotation cell. The understanding of the role of the different zones of turbulent intensity on the particle-bubble interactions is of primary importance to optimization and scale-up of flotation processes and machinery. In order to study particle-bubble interaction in turbulent flow a completely new approach was taken. A laboratory scale stationary turbulence device was developed and built. The set-up allows the observation of particle-bubble interactions in various turbulence intensities, particle and bubble sizes and surfactant concentrations. The experimental set-up consists of a transparent, specially designed tank in which liquid flows between carefully designed and placed obstacles that create different turbulent flow fields. Bubble-particle aggregates are introduced into this turbulent zone. The behaviour of the aggregates, such as attachment /detachment of particles to/from air bubbles is recorded by a High Speed Imaging (HSI) system (5400 fps). The images are then analysed and the dependence of attachment/detachment process is described as a function of turbulent intensity in different conditions for different surfactant concentrations. This paper introduces this method to study particle-bubble interactions in turbulent flow and correlation to Computational Fluid Dynamics (CFD) simulation. CFD modelling is validated for two and three phase systems; liquid-gas with liquid and solid tracers respectively. The CFD simulations using the RANS k-S turbulence model showed good correlation to the experimental data and the experimental method is a promising tool for investigation of particle-bubble interaction in turbulent flow.

Jan 1, 2014

By C. R. Mambote

One of the processes developed for vanadium recovery from the fly ash of crude oil is through acid leaching. In the process, iron is one of the impurities that should be removed before vanadium precipitation, due to the fact that iron tends to co-precipitate with vanadium. The mechanism of iron precipitation is understood in terms of ferric hydrolysis, followed by the dimerization and subsequent polymerization of the crystalline iron compound. In order to develop a new approach for the fly ash processing, in the present paper the precipitation of iron from the liquor after the leaching process was studied with addition of NaOH or NH4OH in the presence of H2O2 or Na2C2O4 at 80°C. The objective was to investigate the feasibility of the selective precipitation which could be applied to vanadium and nickel recovery from the fly ash. The experimental results show the difficulties of removing iron by precipitation without co-precipitating nickel and vanadium.

Jan 1, 2014

The status quo of ecological rehabilitation in metal mine in China and progress in the technology for ecological rehabilitation are presented, including soil reconstruction, soil improvement, plant selection. The present and future research fields are suggested: basic theory of ecological rehabilitation, operative technology of ecological rehabilitation, new technology application research and ecological rehabilitation plan, management and policy.

Jan 1, 2014

By A. Ceylan

Pyrite is present as a gangue mineral in most of complex sulphide ores and most of time it is removed as a tailing. However, beneficiation of pyrite from tailings could be important because of its economical value and for the environmental concern. This paper presents a research for the enrichment of pyrite from copper plant tailings, Siirt-Madenköy/Turkey, by flotation. Siirt-Madenköy copper mine is operated by Park Electric Production Mining and Industry since 2005. In order to obtain the pyrite from Siirt-Madenköy copper plant tailings, laboratory test work has to be done to determine the type of reagents, the flowsheet, and the size of plant. The objective of the company is to develop a pyrite flotation circuit for concentration of pyrite from tailing dam to obtain 500.000 tons/year pyrite concentrate. There are about 3 million tons tailings that containing pyrite in the tailings dam. Experiments were carried out with three different types of tailings from the plant and the pyrite concentrate with 46% Fe and 90% recovery has been obtained. Therefore, this study shows that high grade pyrite with high recovery can be recovered from the tailings.

Sep 1, 2012

By R. Shiva Kumar, G. E. Sreedhar, Rajan Kumar, K. Suresh, A. K. Aketi Veera, M. Narasimha, P. S. Jodan

"In most of the coal washeries, Dense Medium Cyclone’s (DMC) are deployed to treat coarse coal fraction in the range of 50-0.5 mm. DMC’s are very popular due to its ability of high tonnage, ease of operation and effective separation at high near-gravity material (NGM) in feed coal. The ease or difficulty of washing is merely depending on the NGM fraction present in run of mine coal. However, the quantitative effect of NGM on DMC performance was not explored in the literature. Hence, in this investigation, the influence of NGM on DMC performance is focused. With the help of synthetically prepared coal mixture, the effect of NGM mass fraction on separation efficiency is studied in three different approaches. Firstly, by increasing the NGM coal fraction systematically from low to as high as possible; second by varying the distribution of NGM coal; and third by varying distribution of particles lying just above and below the near-gravity zone. Washability studies are also carried out to establish the theoretical yield for the prepared synthetic mixtures. Pilot-plant experiments are carried out in a 4-inch DMC with 1.4 operating separation density treating coal in the size range of 4 - 0.5 mm. From results, the partition curves are constructed by both density and size wise distributions. It is observed that at higher NGM coal fraction i.e above 60%, the performance of DMC is very poor with significant coal particles misplacement. In second approach with increased distribution at higher density fractions, the separation efficiency reduces. In third series the distribution of fraction in near-gravity zone doesn’t much effect the separation except the shift in separation density. It is observed that smaller size (-0.5 mm) coal particle having high NGM content seems have a profound effect on DMC performance leading to significant fines misplacement to wrong products."

Jan 1, 2018

By N. Tsoni

The separation and recovery of fine and ultra-fine particles during the processing of mineral commodities by conventional separation methods is difficult and inefficient. This is due to the problems posed by the very small size of the mineral particles. The fine and ultra-fine mineral particles are either generated during size reduction processes or are necessitated by liberation size. This problem is expected to deteriorate, as deposits of even lower grade are processed. The inefficiency of the conventional separation methods with regards to the processing of very fine particles leads to the loss of considerable quantities of mineral commodities to the tailings. Novel methods and techniques as well combinations of known methods have been tested over the years. Among them, selective aggregation, along or in combination with flotation, has been given much attention. This study deals with the application of hydrophobic agglomeration as a separation method for very fine particles. The selected mineral system is magnesite/quartz, due to its sensitivity to physi-cochemical separation methods. The aim was the selective agglomeration of magnesite using sodium oleate. Tests on single minerals revealed that separation seems feasible and efficient. The parameters examined were: pH, quantity of sodium oleate, conditioning time, and, finally, settling time. Tests carried out on artificial mixtures of the two minerals, under various proportions, confirmed the results obtained from single mineral tests but they were slightly inferior. Finally, hydrophobic ag-glomeration tests were carried out on single and artificial mixtures of minerals using sodium oleate and petroleum as reagents. The results show that the addition of petroleum improves the results. In conclusion, hydrophobic agglomeration can be applied successfully even for fine particles of difficult-to-be-separated systems such as magnesite and quartz.

Jan 1, 2014

By J. Yianatos

The regrinding stage is necessary to achieve the particle size (liberation) for the final upgrade in the cleaning flotation process. At present, vertical mills (Vertimill) are employed at industrial scale, using small steel balls as grinding media. The regrinding process characterization requires mixing regime knowledge along with the mean residence time of the liquid and solid phases. The residence time distribution (RTD) and the actual mean residence time estimations from theoretical relationships are complex due to the presence of three components (solid mineral, balls and water), mass transport characteristics and segregation affecting solid holdup. Therefore, the experimental RTD determination is suitable for industrial mills. In this work, RTD measurements were performed in two different industrial flotation plants. Both plants operate with Vertimills of 1000-1500 HP in the regrinding process with different circuit arrangements according to the plant treatment capacity. The RTD was measured using the radioactive tracer technique. This technique allows for non-invasive tracer detection where the procedure consists of selecting a liquid (Br82 in aqueous solution) or solid (irradiated solid) tracer for RTD data acquisition in real time. The RTD was modelled by the Large and Small Tanks in Series (LSTS) model, which allowed the characterization of the different mixing regimes for both liquid and solids in the regrinding mills. Effective mean residence times in the range 2-11 min were obtained with RTD shapes similar to those obtained in tumbling ball mills. It was found that residence times of liquid and fine particles were similar, which is consistent with results observed in other mixing systems, e.g. mechanical flotation cells. Also, the mean residence times estimated from the RTD allowed the mass balance adjustment to be validated from metallurgical sampling data. RTD estimations are useful for better understanding the Vertimill behaviour and to identify the actual breakage rates. Keywords: vertical mill, residence time distribution, particle size, modeling

Sep 1, 2012

By Peter Riccio

Oxiana Sepon?s mineral processing facility in south central Laos produces copper cathode using leach-autoclave-SX/EW flotation technology. Pyrite recovery in the flotation circuit is critical to the operation, as it is used to generate acid for the leach circuit. However, low pyrite recovery has been an ongoing challenge in the flotation circuit. Tailings characterization work done by Ian Wark Research Institute showed that the pyrite losses to the tail are made up of a combination of coarse liberated particles and finer particles that have been coated by clay fines. In December of 2005, a joint Cytec-Oxiana technical program was initiated to address the pyrite recovery issue. A series of diagnostic tests were performed in the Cytec Stamford Research Facility using synthetic plant water showing that the collector was precipitating as a metal salt, and was un-available for mineral attachment. The tests also identified several collector chemistries that would likely be robust in the Sepon low pH, high dissolved metal ion environment, and will not complex with ferric, ferrous, or copper in solution. With the support of the Sepon on-site engineers, an extensive, successful laboratory program was completed, which then was followed by on plant testing that showed a step wise improvement in pyrite recovery.

Jan 1, 2014