Search Documents

By S. Banisi, O. Farshid, M. R. Rozebehi, A. Bahar, A. Arghavani, M. Mahdavi

At the rougher flotation circuit of the Miduk copper concentration plant (Kerman, Iran) five column cells (CISA) with the diameter of 4m and height of 12m using static mixer type (MicrocelTM) spargers have been installed. Based on the initial design, columns should accept a feed rate of 625 t/h with 80% passing size of 90 µm and solids concentration of 28% and produce 88% of the plant concentrate (i.e., 22 t/h) containing 32% copper. Due to mechanical and processing problems this objective was never realized and theses columns were remained out of operation from the commissioning time (2005). A new attempt with the aim of returning these cells into operation started in 2013. The results of an extensive study indicated that spargers plugging due to the entrance of small amount (2 kg) of coarse particles (up to 2.5 cm) because of usual problems at the plant environment was the main reason of columns non functionality. With a change in the recycle pump inlet design to the column, which prevented the entrance of coarse particles to the spargers, the operation of the column significantly improved. It was found that in order to have a stable operation of the columns at the rougher stage the feed rate for each column should be reduced from 125 (design) to 70 t/h. The air superficial rate had to be also reduced from 1.9 (design) to 0.6 cm/s. A period of 10 days of continuous operation showed that the carrying capacity was 0.23 (g/min/cm2) which was significantly lower that of the design value (i.e., 0.58). The gas hold up was found to be lower than 10% beyond which columns started to move to the turbulent state indicated by "boiling" froth. The average life time of spargers was determined to be 20 days which considered to be very short. The average recovery and concentrate grade of these columns were found to be 68% and 32%, respectively. The high wear rates of spargers, unusually high level of maintenance and supervision needed and instability of the operation made the plant managers not to use column cells as the roughers.

Jan 1, 2014

By K. Amano, K. Haga, Y. Watanabe, A. Shibayama, A. Batnasan, A. Battsengel

"Apatite is an important host mineral in igneous and metamorphic rocks for production of phosphate fertilizers and phosphoric acid, and a potential source of rare earth elements (REE) production. For dissolution of REEs, sulfuric acid is better leaching reagent to develop the economical viable process for recovering of rare earth elements from apatite ore. However, the efficiency of rare earth elements dissolution in H2SO4 is about 30 % due to the formation of calcium phosphate or calcium sulfate as precipitate. On the other hands, phosphorus is mainly produced from phosphate ore. However, when treating rare earth elements containing phosphate ore, rare earth elements were discharged. Hence, development of novel apatite ore treatment process is required for effective utilization of natural resources. In this study, apatite deposit associated with REE was treated with sulfuric acid leaching and two stage precipitation by oxalic acid (C2H2O4) and magnesium chloride (MgCl2) for recovering REE and phosphorus, individually. Results showed that it can be seen the vast majority of La (87.5%), Ce (87.3 %), Pr (86.1 %), Nd (85.2 %) and Y (90.9 %) were dissolved in 1 mol/L diluted H2SO4 solution from the apatite ore. As average leaching rate of REE, over 85% of REE were leached by the condition. In the first stage precipitation using the obtained pregnant leach solution from leaching, over 90% of REE was precipitated by oxalic acid addition after controlling pH to 1 by NH4OH solution. After pH changed to 8.5, over 90% of phosphorus was recovered as precipitate by magnesium chloride addition in second stage precipitation"

Jan 1, 2018

By Kremena Dedelyanova, Tsvetan Damyanov, Nikolay Hristov, Evgeni Kostadinov, Lubomir Kuzev

"Spherical grinding media (balls) are the most widely used media for comminution of ores by grinding. One way to optimize the grinding process in a tumbling mill is associated with the development and testing of a new media shape. By modelling simulation study of the behaviour of two types of grinding media (balls and tetraballpebs) in the grinding process was conducted to determine the possible advantages of the new media shape. Tetraballpebs are in the shape of tetrahedrons with spherical convex walls. D305 mm and L305 mm Bond ball mill sizes were used in the experiment. They are modelled milling tetraballpebs bodies corresponding by weight to five ball sizes, namely ¾, 7/8, 1, 1¼ and 1½ inches which form the grinding media used in a Bond ball mill. They are cast steel grinding bodies. Studies carried out with both types of grinding media include equal number of milling bodies of the same weight and volume. Having thus ensured a uniform mass of the grinding media and the same number of milling bodies, all other conditions and process parameters being identical, conclusions can be drawn about the influence of the grinding media shape on the grinding process. Compared to steel balls, the tetraballpebs used in laboratory tests carried out in closed cycle by Bond ball mill and the study of the rate of grinding gave five to six per cent higher yield of a control size of minus 0.1 mm. Measurements of the Bond ball mill power consumption demonstrated that tetraballpebs grinding media achieved energy saving of 4.7 per cent for the production of one gram of the control size of minus 0.1 mm."

Jan 1, 2014

By Leonardo Soto, Fernando Villanueva

"Antofagasta Minerals S.A. (AMSA), for its Centinela District Project, is currently developing, at a first stage, a new 90 ktpd Concentrator Plant incorporating Esperanza Sur (ESP Sur) and Encuentro (ENC) ores. In order to dimension properly main equipment, specifically for grinding circuit, a final decision has been taken using geological and metallurgical (comminution) data from both body ores. Data was analyzed internally within AMSA and its consultants to get a final proposed circuit for further engineering studies. Specific Energy Consumption (SEC) parameter is one of the main key factors for proper dimensioning. To get an accurate value different tests have been made and modelled to ESP Sur and ENC ores. Also, operational data from Esperanza operation has been taken into account due to its similar ore characteristics to ESP Sur ore and incorporated as input data for design. Depending on data, quality and amount, it is possible to estimate accuracy for project investment and risk level, hence investment decision can be taken under good and reliable information."

Jan 1, 2014

By M. Unesi, S. Haj Mohammadi, M. R. Abdoli, M. R. Garmsiri

"Hydrocyclone-thickener circuit is a promising solution to enhance the dewatering efficiency in mineral industries. The challenges in the circuit is reducing particle size in the thickener feed and the good feature is a rise in the retention time of sediments in the thickener. In this work, the effect of particle size, bed depth and residence time on the thickener performance were investigated. In this order, pilot scale columns were employed at Sarcheshmeh and Shahrebabak copper complexes. Furthermore, the influence of residence time was differentiated due to the variations in the bed depth and settling flux. Moreover, a new approach was introduced to estimate solids residence time in the thickener. results indicated that with smaller particles that are introduced to the column, the bed density as well as thickener discharge solids concentration dropped significantly. It was found that thickener discharge solids concentration fell from 59.6 to 33.8 % with reducing particle size from 130 to 22 µm in the settling flux of 20 t/m2/day. Additionally, it was found that longer residence time and deeper bed resulted in an increase in the thickener performance while the bed depth has a stronger effect. It was proved that employing a hydrocyclone prior to the thickener resuted in an increase in the dewatering efficiency.INTRODUCTION Thickeners are widely employed in mineral industries to recycle tailings and concentrate water content. A limited fraction of suspension water content is recycled using a thickener. For instance, about 50 percent of tailings water content could be recycled using a shallow bed thickener during copper processing. Since the scarcity of global water resources became more serious, the demand for improving dewatering efficiency in mineral industries became more significant [1]. A number of solutions were recommended to enhance dewatering efficiency of thickeners including optimization of current thickeners, employing deep bed thickeners and utilizing thickener-filter or hydrocyclone-thickener circuits. Optimization of existing thickeners is essential, however, it does not meet the significant demand for recycled water. The application of deep bed thickeners (known as paste thickeners) has been rising in the mineral industries [2] due to a higher dewatering efficiency while its costs is remarkable."

Jan 1, 2018

By Zhong Hong

A novel ilmenite collector, tert-butyl benzoic hydroxamic acid (TBHA), was investigated in this paper. The flotation performance and adsorption mechanism of TBHA to ilmenite were evaluated through pure mineral flotation tests, ?-potential measurement and IR spectrum analysis. The experiment results indicated that TBHA exhibited strong collecting capability to ilmenite under pH 6.0-8.5. At pH 7.0-10.0, TBHA existed in the form of anionic species in aqueous solution, and the ?-potential measurement results showed the surface of ilmenite maintained negative and more negative after the adsorption TBHA on it, which inferred that TBHA might adsorb on the surface of ilmenite through chemical interaction. The IR spectrum analysis further confirmed the chemical interaction between TBHA and ilmenite surface. Keywords: Tert-butyl benzoic hydroxamic acid, Ilmenite, Flotation, Chemical adsorption mechanism

Sep 1, 2012

By P. Prusti

An air dense medium fluidised bed separator (ADMFBS) is the efficient process for dry beneficiation of coal. Magnetite powder is used as medium to make required pseudo-fluid density in the fluidised bed. The dynamics behavior of coal particle with reference to its position changes from ideal solution to pseudo-fluid condition in different bed densities depending on its shape, size and density. In this study, three set of projected areas of coal particles were taken. Each set contains four different shapes i.e., cubical, rectangular prism, spherical and triangular prism with different density starting from 1.3 to 1.8 gm/cc. It is observed that coal particles having density less than the bed density, floats in different positions in the dense medium fluidised bed. Higher projected area particles float in deeper height in comparison with smaller projected area. The difference in position of coal particles in the bed increases (nearly 1 to 4 cm) as the coal density approaches towards bed density irrespective of the different shapes. Different shapes of coal particles behave in different ways based on the operating parameters like bed density, coal density and projected area of coal particle. Empirical model equations are proposed to predict the position of coal particle of each shape in the air dense medium fluidised bed system. Keywords: ADMFBS, particle dynamics, projected area, shape

Sep 1, 2012

By R. K. Logric

Bor flotation tailings are very interesting from two reasons: first, is having due value presently, and second represent serious pollutant into this region of Balkan. This paper is only one small part of investigation about processing of valuable minerals from tailings, and desulphurization of this biggest pollutant in the same time, by refloating. The main objective of this work is to pay attention on this problem for resolve greatest environ-mental problem of Serbia and Balkan in the nearly future. Bor is potential regional risk spot, since that failure of its tailings dams would release high amounts of toxic materials that would reach the Danube River. The basic goal of this experimental investigation was finding some possibility for flotation tailings treatment by classical froth flotation. In order was obtained material effect through copper recovery, and environmental protection by moving the rest of reprocessing into the safe place. The work present obtained results of laboratory tests in two laboratories: laboratory of mineral and recycling technology at the faculty in Bor, and laboratory of department of mineral processing of ITNMS in Belgrade.

Jan 1, 2014

By Gaom M. W.

The Mount Isa copper concentrator started operation in 1973. Its secondary grinding circuit consisted of two 5 meters diameter ball mills in closed circuit with 505 mm cyclones. At the design throughput of 800 t/h, the 80% passing size of the circuit product (P80) was about 140 µm. The then Mount Isa Mines Limited (?MIM?) installed two autogenous grinding (?AG?) mills in 1991 to replace two stages of crushing, a rod milling stage and one primary ball milling stage. One of the AG mills was later converted to semi-autogenous grinding (?SAG?) operation by the addition of a steel grinding medium to achieve the designed plant throughput of 800 t/h. The cyclone over-flow P80of the secondary ball mill circuit was reduced to 120 µm by the increased operating power in the AG/SAG mill circuits. The two secondary balls mills had a grinding power of 5.2 MW. A mineralogical study of the milled products indicated that half of this grinding power was sufficient for adequate chalcopyrite liberation. Eliminating one of the secondary ball mills could reduce energy and operating costs by more than A$2 million dollars per year. An optimisation project team was established to achieve the predicted power saving. Grinding circuit simulations were conducted for different circuit configurations. Ball mill parameters such as ball size, ball charge and feed slurry density were optimised. Cyclone body diameter, spigot and vortex finder sizes, and cyclone types were tested. The secondary ball mill circuit was redesigned and several proposed circuits were run as trial production campaigns to determine their operability and efficiency. The plant trials confirmed that one of the secondary ball mills could be decommissioned. Significant cost savings were achieved as a result. The success of the project demonstrates optimising grinding circuits can not only deliver the plant performance, but also a much lower unit operating cost through energy and maintenance savings.

Jan 1, 2014

By V. V. Ramarao

Grinding and flotation operations deliver better-optimized performance when they are monitored and controlled in terms of the minerals they process rather than as elemental assays that we usually refer to. Mesh of grind (MoG), liberation, floatability, grade and recovery etc. are more directly related with the minerals and their characteristics rather than the elemental assays. Hence, online analyzers only provide the status for the grade and recovery of metals and not the direction for the enhanced performance. Central Research and Development Laboratory (CRDL) and Rampura Agucha Mine (RAM) mill section of Hindustan Zinc Limited (HZL) jointly undertook various survey campaigns in the grinding and flotation process streams. Grinding circuit surveys involved systematic collection of representative samples from different grinding circuit streams under stabilized conditions for monitoring particle size and process mineralogy details across individual grinding circuit. Flotation survey campaigns included study of fort-nightly / monthly composites of un-ground flotation feed, lead concentrate, lead tailing, zinc concentrate and final tailing samples for size distribution details in the 150 ? 38 micron range, chemical analysis and mineral characterization through optical microscope. This work details the investigations results and their implications on beneficiation performance. Grinding circuit survey campaigns supported the task for modifying the originally installed configuration of hydrocyclones, to limit recovery losses due to excess grinding of soft galena and related silver minerals. Flotation plant surveys helped in adjusting flotation circuit process parameters to reduce loss of liberated and floatable galena and sphalerite grains into their respective tailing streams. Keywords: grinding circuits, survey campaign, hydrocyclones, mineral liberation and locking, lead-zinc ore beneficiation operation

Sep 1, 2012

The characteristics of mineral resources and tailings resources in China are analyzed. Those tailings, which have double characteristics, can occupy land, pollute environment and even influence human habitat if they are not disposed in time. So pay attention to the comprehensive utilization of the tailing more and more both at home and abroad. The present situation and problems in comprehensive utilization of iron tailings in China are introduced by combine some practice experience, and have looked forward to the comprehensive utilization of iron tailing situation.

Jan 1, 2014

With significant increase in steel output in the world the price of iron ores has been soaring recently. Especially, there is a strong demand for iron ores in China, leading to more attentions paid to developing low grade iron ores. In this paper mineralogy of nm-of-mine hematite ore was deter-mined, and coal-based direct reduction-magnetic concentration was successfully developed to beneficiate low grade hematite ore. Mineralogy analysis indicates that this hematite ore is a super fine refractory ore, with the main valuable mineral hematite being closely associated with quartz and distributing uniformly and mostly occurring within the size of 3~5J.lITI,leading to being difficult to beneficiate due to super fine hematite and only grading 28.83% Fetotal. This hematite ore failed to be effectively upgraded by traditional processes in trial tests, such as reverse flotation, gravity concentration, and magnetic separation, or the integration of the above processes. In contrast with adoption of the coal-based direct reduction-magnetic separation process, concentrate was produced with high iron grade and metallization degree in the present work, which provides a theoretical basis for utilization of low grade iron ores. By optimization of direct reduction conditions, such as reduction temperatures, duration and mass ratio of reductant coal to iron ore, the reduced ore with 93.72% metallization degree was prepared, and then three-stage grinding-magnetic separation of the reduced ore were conducted, the final concentrate was manufactured, assaying 69.54% Fetotal and 98.01 % metallization degree, and with low content of impurities. This iron concentrate with high metallization degree produced by this process is a superior burden for converter instead of blast furnace. This process is enviromnent friendly by directly making iron using coal and iron ores instead of coke, resulting in less emissions and low production cost.

Jan 1, 2014

By C. Y. Sun

Flotation of chalcopyrite and unactivated malachite with xanthates (ethylxanthate, butylxanthate, octylxanthate and dodecylxanthate) is studied in this paper. Minerals interacted with xanthates are detected by FTIR, and simulated by molecular mechanics. It shows that chalcopyrite can be floated with 4 kinds of xanthates, and unactivated malachite can?t be floated with ethylxanthate but can be floated directly with later 3 kinds of xanthates while characteristic absorption peaks of those four kinds of xanthates are all detected by FTIR on chalcopyrite and malachite surface. After simulating the interaction between xanthate and mineral, it shows that H2O and OH-can interact with chalcopyrite and malachite, and their interaction energy may be so called energy bulwark which must be overcome by collector when collector interacts on minerals; the two sulfur atoms in xanthate group interact with copper and neighbor iron atoms on chalcopyrite. It also shows that molecular mechanics results with logP of collectors can interpret the mechanism of xanthate-mineral on atom scale.

Jan 1, 2014

By A. V. Byvaltsev

Adsorption of cyanide complexes of gold, silver, copper, mercury, nickel, cobalt, iron, zinc and cadmium has been studied. Adsorption isotherms of the mentioned metals from individual solutions for different free cyanide concentrations have been obtained. Values of the constants of Freundlich isotherm equation have been calculated. Metal cyanide complexes affinity to activated carbon was determined.

Jan 1, 2014

The relative abundance of coal in India compared to other fossil fuels makes it a natural choice as the primary source of fuel, be it for steel making, power generation or for other uses. The wide variations in nature and type of Indian coals formed during lower Gondawana period and categorized as difficult-to-wash due to its typical mineral matter association with the organic matrix call for suitable beneficiation techniques as the preferred option for quality upgradation. The good quality coking coals of the upper seams are fast depleting leaving behind the inferior quality lower seam coal. The lower seam coals presently being mined are mostly low volatile coking coal (LVC). They constitute about 50% of the total coking coal reserves in India. The beneficiation of Low Volatile Coking coals pose a major challenge and detailed R & D studies was taken up to study the beneficiation characteristics of these coals. The studies revealed that the liberation characteristics at coarser sizes are very poor and the coal is to be ground to finer sizes for liberation. The most important factor that determines coal cleaning efficiency is liberation of organic matter from mineral matter. To achieve liberation grinding is necessary as a result range amount of ultra fines (-0.063 mm) coal is generated. Presence of these large amount of ultrafine in the coal fines, often impose severe technical constraints affecting not only its floatability but also in the downstream treatment of the products like dewatering and cake formation particularly when it is beneficiating through froth flotation. In the present paper optimization of ultra fines (-0.063 mm) has been tried for a LVC coal of Jharia coal field for the better liberation and beneficiation of the above coal fines. It is observed that by optimized, combination of size and number of balls generation of fines can be controlled with liberation. Keywords: coking coal, liberation, floatability, dewatering

Sep 1, 2012

By Narasimha Mangadoddy

The complex nature of multi-phase flow in dense medium cyclones has restricted plant operators and designers to rely on empirical equations for predicting the performance. A number of empirical cyclone models have been developed in the past (Wood, 1990; Dunglison, 2002). In recent years, this subject has been broached with computational fluid dynamics (CFD). Most of the CFD models have not considered the correct rheological behavior of magnetite medium while simulating the medium segregation inside the cyclone. These models mostly predict excessive underflow volumetric flow rates. In this paper simulations of magnetite medium in a dense medium cyclone, were conducted in FLUENT where the particle phases were simulated using the modified Mixture model. The turbulence was resolved using Large Eddy Simulation (LES) model. The rheological behavior of medium was considered in the form of Granular viscosity, Newtonian and Non-Newtonian models corrected with particle loadings and fraction of ultrafines. Multi-phase simulations using granular viscosity option although predict the overall split product medium densities reasonably close to experiments, the mixture viscosity values are restricted to substantially lower values, similar to water viscosity. Simulations using Newtonian viscosity model corrected with particle loading, and fine fraction below 53µm size is predicting overall mixture viscosity levels well over water viscosity levels, but under predicting the under flow the underflow medium density. Multi-phase simulations using Non-Newtonian Herschel-Buckley model, calibrated for superfine magnetite medium measured viscosities, is closely predicting the medium segregation with gamma ray tomography data. Overall predicted product medium densities, underflow volume split are close to the experimental data. This model is can be further used to simulate coal portioning and hence in developing new designs.

Sep 1, 2012

By V. Panayotov

Slag and by-products of metallurgy bear valuable components and their processing raises an in-creasing interest. Coke and iron have to be separated and other components have to be depressed, in order to obtain sellable high quality copper concentrates. Use of classical mineral processing technologies, such as magnetic separation, sulphidization, hydrometallurgy, etc. yields copper concentrates with grade of 4%~6% Cu. Copper is lost in tailings and the whole technological cycle is low profitable. Technology proposed applies an electrochemical treatment of the industrial water entering the flotation cycle. Iron and iron compounds that do not bear Cu, coke and gangue materials are depressed during the copper flotation. Copper concentrate of grade of 9.8%~10% Cu is obtained at simultaneous increase of Ag recovery by 8%~10%. As a result company profitableness is increased. Technology proposed is easy to implement, it does not require changes in the existing technology flow-sheet, and additional investment is low. The flotation process can be aided by a specially developed system for real-time analysis of the obtained copper concentrate which allows in-time corrections in the flotation parameters and entire process control. Applied flotation schemes, technological parameters and results obtained are described.

Jan 1, 2014

By A. N. Zagorodnyaya, T. N. Bukurov, Z. S. Abisheva, A. S. Sharipova

"This work presents the results of the development of a flowchart for the processing of copper production dusts resulting in the production of of lead sulphate, tribasic lead sulfate (TBLS), ammonium perrhenate, zinc, copper-cadmium cake.Dust having the following composition (wt. %): Pb 39.3, Zn 6.5, Cu 5.5, Stotal 10.8, As 1.05, SiO2 0.6, Cd 0.8, Bi 0.04, Ag 0.02, Re 0.03 was used in the work. Chemical and X-ray analyses indicated that lead, zinc and copper are generally present in dusts in the form of sulfates, various amounts of oxides, sulfides, silicates; sulfur (according to chemical analysis data) is present in the form of sulfates (~ 90%) and in the form of sulfides (~ 10%).Studies have been made on two-stage stripping of copper production dusts containing lead, zinc, copper, cadmium, rhenium in the form of various compounds, at first with soda solution, then with nitric acid solution. It has been indicated that the combination of the operations allows the recovery of 98% rhenium, 82% lead, 92% copper, and 96% zinc and cadmium each in the solution. Furthermore, at the stage of dust leaching with soda, 80% of rhenium and 0.01% of nonferrous metals each are recovered in the solution. Remaining quantities of all metals are recovered in nitric acid solution up to maximum values. Such behaviour of metals is caused by metal phase content in dusts and properties being formed during leaching of compounds. At the stage of dust leaching with soda solutions, carbonates with various compositions are formed due to the exchange reaction between nonferrous metal sulfates and sodium carbonate. The conversion of PbSO4 into PbCO3 is apparently occurs in the solid phase and the conversion of readily watersoluble zinc, copper, and cadmium sulfates into that of carbonate salts occurs in the liquid phase. Rhenium passes into solution due to the presence of rhenium greater quantity in dust in the form of readily soluble perrhenate. Some portion of the perrhenate is, probable, blocked by lead sulfate and liberated in the conversion of PbSO4 into PbCO3."

Jan 1, 2003

By Xiong Dahe

"SLon vertical ring and pulsating high gradient magnetic separator utilizes the combined force field of magnetism, pulsating fluid and gravity to beneficiate weakly magnetic minerals with the advantages of large beneficial ratio, high recovery, matrix not easy to be blocked and excellent performance.We have developed SLon-750; SLon-1000; SLon-1250; SLon-1500; SLon-1750 and SLon-2000 VP HGMS. Now more than 200 of them have been successfully applied in China.Application in Qi Dashan Mineral processing Plant of Anshan Iron and Steel Company: The iron ore consists of magnetite and hematite. In 2001, six SLon-1750 magnetic separators are applied to control the tails grade of fine hematite. The results of flowsheet is: feed grade 30.15%Fe, concentrate grade 67.00%Fe, iron recovery 75.86%. The results set up the historic high record of this plant and the processing coast is greatly reduced.Application in Gushan Iron Mine of Ma Anshan Iron and steel Company: There are 6 SLon-1750 and 4 SLon-1500 magnetic separators applied in this mine to treat refractory hematite ore. The feeding grade is about 45%Fe. The final iron concentrate grade is about 60%Fe and the iron recovery is about 76%. The results are much better than the previous gravity flowsheet.Application in Meishan Iron Mine of Shanghai Baoshan Iron and Steel Company: The mined ore consists of magnetite, hematite and siderite. Because of a relatively high content of phosphorus, the iron concentrate could not meet the market requirements. Now 18 SLon-1500 magnetic separators are applied to reduce phosphorus, which is reduced from about 0.4%P to 0.246%P. The quality of iron concentrate is greatly upgraded.Application in Panzhihua Ilmenite Processing Plant: In the past, the -0.045mm ilmenite fraction was discarded in to the tails because of lack of high efficient equipment. In 2001, the plant built up a magneticflotation flowsheet to recover the fine ilmenite from the -0.045mm fraction with 6 SLon-1500 magnetic separators. The total results are: feed grade 11%TiO2, concentrate grade=47% TiO2, recovery 44%. Each year the flowsheet recovers 60,000t fine ilmenite concentrate."

Jan 1, 2003

By Douglas Fuerstenau

"Comminution not only is the major energy cost in mineral processing but it also can limit the grade of ores that can economically be processed. Rittinger first postulated that the energy for comminution is proportional to the new surface produced. Because most of the strain energy needed to initiate and propagate cracks in particles cannot be recovered, researchers reported woefully low comminution efficiencies. Recognizing this, Schoenert proposed that the baseline for assessing comminution efficiency should be the mechanical energy needed to break single particles. After extensive single-particle studies, Schoenert turned to comminuting beds of particle in piston dies. Finding particle-bed comminution to be energy efficient, he had the brilliant conception of making the process continuous, namely his invention of the choke-fed high-pressure roll mill (HPGR). Practical comminution involves masses of particles, which can lead to energy efficiencies far less than that of single-particle breakage. A three-way classification of grinding modes in terms of the mobility of the particle mass provides the necessary insight into the low efficiency of different comminution machines: namely, single-particle breakage, confined particle-bed grinding (HPGR), and loose-bed grinding (ball mill). Examples are given for determining and comparing comminution efficiencies. The size distribution of comminuted products become self-similar, and a single parameter, the median size, can be used to quantify the extent of comminution. The reduction ratio, expressed in terms of the mean size of the feed and product, varies linearly with expended energy and the slope of such plots is a measure of the grindability of the mineral. This approach clearly gives the order of energy efficiency as single-particle > particle-bed > loose-bed comminution. HPGRs are more efficient at low reduction ratios but lose that advantage at higher reduction ratios. Extensive hybrid grinding experiments carried out with our instrumented ball mill and HPGR showed significant energy savings by first comminuting the material in the HPGR and followed by the ball mill. At Cerro Verde an industrial-scale hybrid HPGR/ball mill system is reported to have a 13 percent energy savings over a SAG mill/ball mill system."

Jan 1, 2014