Search Documents

By Lei Wang, Qi Zheng, Xiao-kui Che

"The wastewater emitted by gold chemical industry contained vast of different heavy metal ion, such as Zn, Cu and Ni etc. Among them Zn is the main ion in the waste water which causes the serious environment pollution. A method of preparing a kind of resin which is used for the removal of Zn by magnetic adsorbent was developed and was applied in practice. This adsorbent is a chitosan made of a kind of Fe3O4-chitosan modified by epichlorohydrin. The adsorption capacity of the absorbent and it was concluded that under the laboratory conditions, the maximum adsorbing capacity of this adsorbent could be 287.58 mg/g. The absorbent was also applied in the wastewater emitted by a gold industry in Shandong province. Its performance was tested and the result showed that the concentration of Zn ion in the wastewater was reduced from 0.58 mg/L to 0.0174 mg/L. What is more, the adsorption rate could be more than 97% when the dosage was 100L/m3 after adsorbing for 1h. KEYWORDS Selective, preparation, laboratory experiments, industry experiment, comparation INTRODUCTION Currently, most gold chemistry use cyanide to leach gold ore. Many different metals participate to this reaction besides the gold ion in this processing, so that the composition of the water is very complex. The waste water emitted by gold chemistry industry contains large amount of heavy metals. Definitely, if it was discharged without any treatment, the water would threaten the environment. The recuperation of any ion in the water would mitigate the pollution. Ion exchange resin, which is an effective material to do the water treatment with low cost, became widely applicated in this field [Yu-jiao Wang,2013]. Different kinds of resin were developed and the influence factors such as pH, adsorption properties and selectivity for different ions were investigated [CA Cruz et al,2018; PawanKumar et al.2016; Y Zhang, et al,2010; and ShengingSun, Aiqin Wang, 2006;]. The waste water mentioned in this article has a high Zn concentration, so a magic resin for Zn adsorption selectively we designed was used to manage this water. And the recovery of Zn could not only contribute to pollution abatement but also a best way to settle a dispute to the short of Zn resource. So the article mainly describes the preparation and the application of a kind of magnetic adsorbent used for the removal of Zn both in laboratory and industry. The aim of this article is to compare the effect of this resin in industry and laboratory?"

Jan 1, 2018

By Xuliang Yang, Yuemin Zhao, Bo Zhang, Liang Dong, Cheng Sheng, Gongmin Li, Zhenfu Luo, Yaqun He, Chenlong Duan

Coal plays an important role in the primary energy consumption of all over the world. In 2012, coal reached the highest share (29.9%) of global primary energy consumption since 1970. Coal burning mainly contributes to the emission of SO2, NOX, Hg and other impurities that jeopardize the future of environment. . Beneficiation before coal utilization is the most economical and effective technology for removing the hazardous material and gangue. In this paper, a novel process of dry beneficiation based on gas-solid two-phase flow composed of the compound dry cleaning separator (FGX), the air dense medium fluidized bed separator (ADMFB) and the vibrated fluidized bed with autogenous medium (VFB) is proposed. The main equipment and the flowsheet of the united system are described in detail. Separating principle of the FGX, ADMFB and VFB devices are all based on gas-solid two-phase flow. In FGX, gassolid suspension is composed of continuous gas flow and coal powder in feed coal. Large size coal (+6- 80mm) can be pre-separated effectively, and large size gangue can be removed effectively. Moreover, - 6mm particles fed serve as autogenous medium in FGX. The probable E value is 0.13 for -80 mm raw coal. In ADMFB, magnetic powder with -0.3 + 0.045 mm size fraction and coal powder in feed coal are compound medium solids. The separation density can be adjusted and controlled according to properties of raw coal. -50 + 6 mm raw coal can be cleaned efficiently, the probable E value is 0.05. In VFB, -6 + 1 mm coal can be separated. Generally, -80 mm raw coal can be cleaned efficiently in the united system based on gas-solid two-phase flow.

Jan 1, 2014

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003

By E. V. Bratygin, E. G. Dmitrieva

The aim of the research was to study the thermodynamic characteristics of high-temperature processing of ilmenite concentrate deposits "Central" in a neutral and oxidizing atmosphere, as well as its interaction with alkaline additives. The research was conducted using a scanning colonoscopy on thermogravimetrical analyzer NETZSCH STA 449 F3. A sample of the test material weighing 10 mg was placed in a crucible and heated at a rate of 10 °C/min to 1200 °C in argon or air. Studies have been conducted pure ilmenite concentrate and its mixtures with 5 % and 12.5% of sodium carbonate. The results of the analysis of the thermogravimetric curves it was found that the recovery of the concentrate carbon will come from ulvospinel, not pseudobrookite, and the reaction recovery is possible at temperatures above 900°C. While removing produced in the decay ilmenorutile of iron oxides in an inactive form, for example, iron (III) oxide, it is possible to reduce the quantity of the solution of ilmenite formed during the restoration of the melt anosovite. The analysis of data obtained during heating of ilmenite concentrate with sodium carbonate in concentrations of 5 and 12.5% transition pseudobrookite in ulvospinel is missing, it just breaks down into hematite and titanium oxide, which, in turn, react with N?2??3. It should be noted that increasing the concentration of sodium carbonate in the sample contributes to more complete interaction of iron oxides and N?2??3 with formation of ferrites of sodium. This can ensure full recovery of iron oxides in the concentrate, which is part of secondary ilmenite can not be dissolved in the melt formed by the lower oxides of titanium. In addition, the increase in the content of soda in the mixture significantly reduces the temperature of the initial melting point of the slag and facilitates the coagulation of metallic iron.The obtained results were used for laboratory studies of the solid-phase sintering of briquettes from ilmenite concentrate with additives of sodium carbonate and a reducing – coal, as well as for the development of technological mode of solid-phase sintering of the concentrate with the aim of obtaining product recovery with a titanium dioxide content of more than 75 %.

Jan 1, 2018

By Arkady Senchenko

At present, there are different traditional and modern methods for ore grindability evaluation. The correct and rational approach to sampling, testing methods and mill sizing enables one to design a workable technology. This paper contains TOMS institute experience in different grinding indices determination over the last 7 years (SAG Design Test, BWi, CWi, RWi, and other). Mill sizing examples and circuits modeling for the projects in Russia and Kazakhstan are considered. Keywords: ore grindability, SAG Design Test

Sep 1, 2012

By N. N. Ngoepe

Positron Emission particle tracking (PEPT), which makes use of a radioactively labeled tracer particle, a positron camera and a tracking algorithm has been shown to be a viable method for studying flow properties in both the pulp and froth phases of flotation cells. Detailed velocity measurements of 300-400 µm glass beads were extracted to assess turbulence from velocity fluctuations in a micro flotation cell. The effects of particle speed and orientation at the instant of attachment events were studied. A minimum speed of 0.16 m/s was needed for a collision to lead to attachment. The most attachment events happen when the particle is directly in line with the inlet tube at 90o.

Sep 1, 2012

By F. Boylu

In this study, Ca-bentonite was subjected to a series of systematic hydrocyclone tests with the aim of developing separation procedures and in turn achieving optimum recoveries. In hydrocyclone tests, vortex and apex diameters and also feed pressures were investigated. In each hydrocyclone set, vortex diameter was kept constant while the other two parameters varied to produce bentonites con-centrates of various smectite contents. The separation efficiencies were evaluated based on the cation exchange capacity (CEC), particle size and swelling index. The detailed hydrocyclone tests showed that, upgrading of Ca-bentonites require procedures different from the bentonites reported in the literature. Sodium and mixed bentonites are easy- to-disperse and easy-to-separate whereas calcium types need to be scrubbed rigorously for disintegration. Scrubbing properties of ca-bentonite were investigated as a function of scrubbing time and percent solids by weight (PS). The scrubbing conditions at 700 rpm for 1.5 hours and percent solids of 30 % were found more effective for achieving a better quality bentonite. In addition to the parameters mentioned above, the effect of percent solids on hydrocyclone separation was also studied. Although Ca-bentonites permit studying at higher percent solids, increasing solids content of the pulp deteriorated the quality of the clean products. Application of an appropriate separation scheme enabled the development of a unique separation procedure involving stage wise scrubbing followed by hydrocycloning which yielded calcium bentonite concentrates with CEC of 90 meq/100 g and high swelling indexes of 12 mL from the original bentonite of 65 meq/100 g and 7.0 mL, respectively. These results indicate that upgraded bentonite products can be conveniently used in various diverse industrial applications including bleaching earth, desiccant, cat litter, paper etc.

Jan 1, 2014

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

The objectives of this study were to propose a viable alternative method for recovery of precious metals such as gold (Au), silver (Ag) and palladium (Pd) from waste printed circuit boards (WPCBs) and to regenerate the spent lixiviant solution for reuse. The proposed method generally consists of several steps as follows: 1). iodine-iodide leaching for metals extraction; 2). separation and recovery of precious metals and metal impurities from a pregnant leach solution; 3). regeneration of the spent iodine-iodide solution/lixiviant. In this method, more than 99% of Au leaching was achieved in the iodine-iodide solution from the solid residue of WPCBs that was obtained via sequential processes including incineration at 800 ?C and high pressure oxidative leaching with a diluted sulfuric acid at 120 ?C, while the leaching of Ag and Pd was less than 1%, respectively. Besides Ca, Cu, Ni, Co and Zn as main metal impurities, leaching efficiency of other metals did not exceed 1%. The precious metals and base metals as metal impurities present in the pregnant leach solution were separated and recovered by precipitation using L-AA and NaOH solutions. About 99.8% Au, 81.7% Ag and 72.8% Pd were recovered from the pregnant solution at pH of 2 with the addition of 0.1 M L-AA as precipitating agent. The remained small amounts of precious metals and metal impurities were precipitated at pH 13 using 1 M NaOH. The spent lixiviant after sequential precipitation was regenerated in the presence of hydrogen peroxide, hydrochloric acid and potassium iodide. It was revealed that over 90% of gold could be extracted from the residue of WPCBs with the regenerated lixiviant solution.

Jan 1, 2018

By Andrei Yevdokimov, Ivan Sidorov, Olga Lanchakova, Olga Khmelnitskaya, Tatiana Chikina

"The paper focuses on the results of the research on development of hydrometallurgical process of gold recovery from refractory sulfide flotation concentrates based on fine and ultrafine grinding. Refractory concentrates (the degree of refractoriness is 16.9%-82.6%) were chosen for testing. The efficiency of the process based on fine and ultrafine grinding to treat flotation concentrates with gold intergrown with sulfides and rock-forming minerals was shown. Based on the test work conducted, the process option was chosen. In included grinding of flotation concentrate to the size of 98% minus 20µm in a bead mill, lime treatment with air blow, CIL, filtration and detoxification of liquid phase of the slurry. This process (compared to the basic option) provides the recovery of gold from 82.6%, up to 94.0% and decreases the residual grade in the tailings from 3.3g/t to 1.1g/t at the consumption of 12.6NaCNkg/t. Based on the results of the test work and pilot plant testing, project design criteria of flotation circuit at a Russian plant was developed."

Jan 1, 2014

By V. Ross

"The Upper Group 2 (UG2) reef in the Bushveld Complex in South Africa hosts an estimated 40% of the world’s Platinum Group Metal (PGM) resources. The processing of this ore via flotation poses two particular challenges: limiting the levels of chromite in the concentrate to reduce downstream smelting problems, and enhancing the recovery of ultrafine (typically -10 micron), liberated PGMs. Conventional ways of suppressing the entrained chromite, such as froth washing, is not effective in PGM operations, which are dominated by mechanical cells. The recovery of fine particles is hampered by low collision efficiencies with air bubbles, as well as oxidised surface layers especially in tailings operations. This paper documents the results of laboratory tests on a run-of-mine PGM UG2 ore, investigating the application of a pneumo-mechanical column (PMC) and its effect on PGM flotation and its selectivity with regard to chromite. A key feature of the device is the stage-wise release of aerated slurry from an agitated downcomer, thus creating conditions where the superficial velocity profiles of air and slurry change axially within the separation zone. This aids segregation of the silicates and chromite-rich fractions in the separation zone, concentrating the latter towards the bottom of the column and minimising its entrainment into the concentrate. Comparison of the performance of the PMC to that of mechanical laboratory cells under equivalent operating conditions showed improved PGM flotation kinetics and recovery. This was accompanied by a decrease in gangue recovery compared to the mechanical cells by more than 40%, thus doubling the final rougher concentrate grade from 50 to 100 g/t. Significantly, whilst the overall Cr2O3 recovery was reduced by more than 60%, the selectivity (PGM recovery vs Cr2O3 grade in the concentrate) was doubled.INTRODUCTIONThe Bushveld complex in the northern part of South Africa hosts the world’s largest reserves of Platinum Group Metals (PGMs), representing approximately 40% of the total PGE. It is characterised by three main PGM bearing reefs, namely Merensky, Upper Group 2 (UG2) and the Platreef. The Merensky and Platreef are dominated by silicates in the form of pyroxenites, and carry economically recoverable amounts of copper and nickel, in the form of chalcopyrite and pentlandite. The UG2 on the other hand is a chromitite ore with chromite as (ideally, FeO.Cr2O3) the most abundant gangue, often constituting more than 70% by mass with a PGM grade of around 4.5 g/t. Other key gangue minerals are pyroxene, feldspar and talc. The PGEs occur in a wide variety of minerals, with platinum and palladium sulphides typically accounting for about half of the total. Base metal sulphides such as chalcopyrite, pentlandite and pyrrhotite occur in only very minor amounts, accounting mostly for less than 0.1% by mass."

Jan 1, 2018

By Frank van der Meer, Lea Quincke

"High Pressure Grinding is applied to achieve size reduction of the particles by inter-particle breakage and to generate micro-cracks in the product particles as a contributing factor in e.g. leaching or mineral liberation. As alternative to classification, a closed circuit operation for HPGR can be established by product recycling, where a proportion of the coarser edge material and parts of the center material are split-off to be recirculated to achieve a finer final (center) discharge product for subsequent processing steps as ball mill grinding or beneficiation. As a result of the product recycling, the content of fines in the feed material increases and may affect the grinding efficiency in terms of production of fines and the generation of micro-cracks in the particles. In the scope of this paper, the effects of the proportion of fines in HPGR feed on grinding efficiency and micro-crack generation were evaluated. Grinding tests were executed with different feed size distributions, from a fines-void situation (truncated feed) to a fines-abundant situation (high product recycle). The evaluation of grinding efficiency and generation of micro-cracks was done by particle size analysis, Bond Work Index tests, impact tests on HPGR feed and products, and X-ray computed tomography of single product particles. This publication summarizes the main aspects of the outcome of these investigations."

Jan 1, 2014

By Y. H. Tang, H. Y. Zhang

"Tailings from lead-zinc mine contain plenty of dolomite and low-grade fine-grained barite, which is difficult to enrich by mineral processing. Since the density of barite and dolomite has some differences due to the fine dissemination size in a complex sedimentary, the gravity separation tests were conducted with no results obtained. The magnetic separation was conducted to remove the magnetic gangues, and the results were not satisfactory because of the gangue minerals such as limonite and others were low in content. The results of floatation tests showed that the mineral separation of barite and dolomite is quite difficult because that they have similar mineral floatability. Experimental research shows that the good results can be obtained by “desulfurizationbarite floatation” processing with the new depressant TS. The barite concentrate containing BaSO4 91.27%, BaSO4recovery is 70.25% when sodium dodecyl sulfonate serves as a collector and TS as the depressant.INTRODUCTIONBarite is an important mineral material. Often associated with other minerals, it usually needs to be separated by mineral processing in order to meet the application requirements. The main barite beneficiation methods include hand sorting, gravity separation, floatation, magnetic separation, acid leaching, etc. Usually barite associated with oxide ore such as fluorite dolomite, quartz ore etc. are also associated with sulfide ore such as pyrite, sphalerite and galena. The separation between barite and sulfide ore (such as pyrite) is easy. On the other hand, the separation between barite and oxide ore (such as dolomite and fluorite) is very difficult. There are quite a lot of reports on the separation between barite with fluorite dolomite however the separation between barite and dolomite is seldom discussed.The ore properties are quite complex attributable to mineral assemblage containing a large amounts of dolomite. As the density of barite and dolomite has some differences, gravity separation between them is usually easy. The gravity separation tests were conducted with no results obtained due to the fine dissemination size in a complex sedimentary. The magnetic separation was conducted to remove the magnetic gangues, and the results are not satisfactory as the gangue minerals such as limonite and others were low in content. Due to the fine dissemination and intimate association of minerals, and barite and dolomite contain the same group ions of Ba2+, Ca2+ and Mg2+, the results of flotation tests showed that the mineral separation between barite and dolomite by flotation means problematic. Previous studies have been conducted by several institutions but none to date has come up with a satisfactory process in dealing with the deposit. This may be attributable to: high cost of reagents; unsatisfactory performance. Therefore, the key to the flotation separation of barite and dolomite is the application of selective inhibitors. Based on previous test observations and years of extensive research experience in barite processing technology, with the new depressant TS has selectivity inhibition on dolomite developed and used, good results can be obtained by “desulfurization-barite flotation”, which allows barite in the lead-zinc tailings to a comprehensive recovery."

Jan 1, 2018

In order to determine the optimal process parameters of agitation leaching and provide industrial process design parameters, experiments were carried out on leaching behaviors of copper oxide ore with high mud content. Condition tests show that the main factors affect the leaching efficiency as follows: Temperature, Initial acid concentration, leaching time and particle size. As the temperature increases, the copper leaching rate was increased. At 60 ?, the initial acid concentration 80g / L, leaching time 2h, liquid-solid ratio 2:1 and grinding fineness65%-0.074mm, the optimal copper extraction was 83.15%, the acid consumption was 187.91kg / t. ore. Keywords: agitation leaching, copper oxide ore, mud

Sep 1, 2012

By B. Vasanthakumar, H. Ravishankar, S. Subramanian, J. Braun

The flotation of sphalerite and galena in the presence of intra- and extra-cellular components isolated from Bacillus circulans before and after adaptation to the chosen minerals has been studied. Based on various biochemical treatments, the key biomolecule primarily responsible for the flotation of sphalerite has been identified as DNA, which functions as a bio-collector. A noteworthy finding is the considerably higher flotation recovery of sphalerite obtained in the presence of single stranded DNA (79.8%) vis-à-vis double stranded DNA (50.2%). Selective flotation tests using the soluble fraction obtained after thermolysis treatment highlight that sphalerite-adapted cells yield a higher selectivity index (S. I.) of 31.2 compared to galena-adapted (S.I. 4.3) or unadapted (S.I. 12.2) cells. During bacterial adaptation to the above chosen minerals, the quantitative and qualitative changes in the surface potential, surface morphology and cell wall components have been monitored. The prior adaptation of the bacteria to sphalerite results in the secretion of a higher amount of proteins, eDNA and phosphate, whereas adaptation to galena leads to a higher amount of polysaccharide, uronic acid and acetylated sugar, vis-à-vis the unadapted bacteria. A significant observation is that the bacteria undergo a change in morphology from rod to sphere as a strategy to resist metal toxicity during adaptation to galena. Interestingly, this phenomenon is not observed during bacterial adaptation to sphalerite. This morphological transition has been shown to involve changes in crucial cell wall components as well as changes in the levels of expression of bacterial cytoskeleton element mreB gene involved in the maintenance of the rod shape. The sequence of B.circulans mreB gene has been identified using Polymerase Chain Reaction (PCR) followed by DNA sequencing.

Jan 1, 2014

By I. I. Maximov

The paper describes the results of studies performed with a view to develop an improved technology for processing high-grade massive and cupriferous ores of the Talnakh deposit, the main valuable components being nickel, copper and PGM. The studies? main task was production of nickel concentrate with nickel content of approx. 15%, nickel recovery being as high as possible. The studies were performed on two ore samples. One sample was a mix containing high-grade massive (78%) and cupriferous (22%) ores with nickel content of 1.93% and copper content of 3.6%; the other sample was a mix of high-grade ores with nickel content of 2.25% and copper content of 3.72%. Main ore minerals were copper sulfides ? chalcopyrite and cubanite, their total content being 10.5% ~ 11%, pentlandite (5.2% ~ 6.1%) and pyrrhotite (36.7% ~ 42.9%). Influence of grinding media on pentlandite and pyrrhotite separation results, achieved through combined use of triethylenetetramine (TETA) and sodium sulfite (SS), was also investigated. It is shown, that combined application of TETA/SS in the ratio of 1:2, permits to grind products in metal mill (mild steel) with metal balls (mild steel), achieving results that are similar to those achieved by means of grinding in inert grinding media with TETA/SS ratio of 1:1. Application of the developed technology provided for production of high-grade nickel concentrate with nickel content of 14.7% ~ 15.6%, nickel recovery being 76 % ~ 77%. Earlier experiments performed on the above mentioned ore mix permitted to produce nickel concentrate with nickel content of 10%, nickel recovery being 75.9%. Consequently, nickel content was increased by 4.7% ~ 5.6%, and a higher nickel recovery was achieved. The paper also describes metallurgical results related to nickel, copper and PGM with regard to all processing products.

Jan 1, 2014

By B. P. von der Heyden, P. Neethling, M. Tadieb, L. Babedi

The effects of trace element substitutions in sphalerite mineral structure on optimised floatation response have, as yet, not been fully constrained or fully understood. To further this important field of study, this contribution focusses specifically on mineral and surface chemistry, and electro-chemistry of Cd- and Co- substituted synthetic sphalerites using Raman spectroscopy and Zeta potential experimentation. Raman spectroscopy illustrates that the presence of these impurities results in the introduction of a new mode, the relative intensity of which can be correlated (Cd r2=0.95 and Co r2= 0.99) to the dopant concentration. Comparison to X-ray Diffraction results measuring the unit cell parameter further shows that this relative intensity (Cd r2=0.81 and Co r2= 0.99) may provide insights into the degree of lattice strain within the mineral structure. The zeta potential distribution of an un-activated Cd-sphalerite show no detrimental effect as function of Cd content. Although the iso-electric point shifted from 2.45 at 1 wt.% Cd to 2.69 at 3.68 wt.% Cd, the zeta potential remained negative at alkaline media. Conversely, cobalt at low concentration of 0.36 wt.% had a detrimental effect on the surface charge, resulting to a close to neutral zeta potential at different pH. The adsorption of Cu ions on the surface of Co-bearing sphalerite conditioned in an alkaline media slightly increases the zeta potential of Co-sphalerite. While the Cd-bearing sphalerite decrease in negative zeta potential at >1 wt.% Cd indicating a complete exchange between Cu and Zn. The results presented herein illustrate that, based on the chemical nature of the substituting metal; sphalerite will exhibit multiple response to flotation reagents. Maximum recovery of zinc can thus only be achieved through multidisciplinary study and fundamental understanding of the effects of cation substitution on mineral structure and surface chemistry, the latter necessarily affecting the floatation response.

Jan 1, 2018

By Yizhong Yuan, Dao Li, Nannan Xue, Tao Liu, Yimin Zhang

A new multi-stage counter-current circulation leaching process for extracting vanadium from stone coal was proposed, and the main factors on multi-stage counter-current circulation acid leaching process were investigated. The results show that the vanadium recovery could reach 86% under the conditions of sulfuric acid concentration of 4 M, liquid to solid ratio of 2 mL/g, temperature of 95 °C, reaction time of 60 min, mean particle size of 125 µm and circulation acid leaching stage of three. The losses of vanadium in acid leaching solution appeared during the four-stage acid leaching process. The strong adsorption performance of new formed KAl(SO4)2(H2O)12 crystal was main reason.

Jan 1, 2014

By Tohru Kamo, Shigeyuki Katano, Hideki Nakagome, Maiko Adachi, Shingo Nakamura, Kaneshi Taniguchi, Zar Zar Hlaing, Takaaki Wajima

Tantalum capacitor is a small-sized and has large capacity, and is indispensable for electric equipment. The demand increases year by year, and a quite large number of used tantalum capacitors is generated. Recovery of tantalum from tantalum condenser is recently important since production of tantalum have not been stable for the price and the quality. However, recovery of tantalum from tantalum-condenser is difficult since tantalum parts strongly cover with the flame retardant resin made of halogenated compound (mold resin). This research investigated recovery of tantalum parts from tantalum condenser using steam gasification with mixed molten carbonate. Mixed molten carbonate (Na2CO3:K2CO3:Li2CO3 = 1:1:1) (3 g) put into the reactor, and heated with electric furnace while flowing nitrogen (160 mL/min) and steam (1 mL/min) warmed by heater. After heating to setting temperature (450 - 650 oC), tantalum condenser (3 g) was put into the reactor, heated for 5-10 min, and then cooled to room temperature to recover the reacted capacitor by filtration after treating with distilled water. At relatively low temperature (550 oC) heating for 10 min, mold resin can be decomposed by using steam gasification with mixed molten carbonate, in comparison with using pyrolysis and steam gasification without carbonate, and decomposition reaction occurred over 500 oC by using steam gasification with mixed carbonate. Recovery of tantalum parts from capacitor is successful using steam gasification with mixed molten carbonate at 530 oC for 5 min, due to the effective decomposition and removal of mold resin from capacitor. Furthermore, most halogen gas generated from decomposition of mold resin can be trapped in molten carbonate not to exhaust halogen gas. These results suggested that recovery process of tantalum parts from used condenser using steam gasification with mixed molten carbonate is expected as a feasible way to recycle the rare metal in electric equipment.

Jan 1, 2014

By S. A. Vorobyev, Yu. L. Mikhlin, Ye. V. Tomashevich, A. A. Karacharov, M. N. Likhatski1, A. S. Romanchenko, S. V. Saikova

"A set of state-of-the-art methods have been applied to study ultrafine particles and nanoscale species arising on mineral surfaces upon milling, interaction with flotation reagents, and leaching of base metal sulfide ores in order to gain insights into interfacial mechanisms. The fine fractions produced by ball milling of a Pb-Zn Gorevsky ore and four Cu-Ni sulfide ores studied with laser diffraction, dynamic light scattering, zeta-potential measurement, Xray photoelectron spectroscopy (XPS), SEM, TEM and other techniques. The particle size distributions had, aside from the peaks at 20-60 ?m, maxima near 1-2 ?m; the flotation was considerably suppressed when the yield of positively charged ultrafine particles approached tenths % (several kg per ton). High-energy XPS and X-ray absorption spectra revealed that sulfide minerals depleted in metal in air and aqueous solutions were composed of outer “polysulfide” layers, strata with disulfide species, and heavily defective underlayers, and “passivation” was explained by stability of the metal-deficit structures. Dixanthogen at pyrite and copper-activated sphalerite, dixanthogen and then cuprous xanthate on chalcopyrite, and chemisorbed xanthate at galena were specified as the main interfacial products using cryo-XPS of fast-frozen flotation slurries. The particle size, zeta-potential and behavior of colloids of Cu and Pb xanthates and dixanthogens were largely determined by the initial ratio of a cation and collector; the properties of copper xanthate nanoparticles were also affected by incorporated dixanthogen (about 15 wt.%). Submicrometer gas domains of 3-8 nm in height and “hydrophobic” forces upon the probe retraction were found on xanthate-treated minerals using atomic force microscopy and spectroscopy; their impact on flotation is briefly discussed.INTRODUCTIONInterfacial phenomena play a key role in flotation, leaching, water purification and related environmental processes. The mineral processing and extraction of metal from sulfide ores commonly involves milling the ore, which produces, along with the particles of 20 µm to 100 µm, mineral entities ranging from micrometer to submicrometer and nanometer scale. Furthermore, ultrafine particles of flotation reagents, products of metal sulfide oxidation, and so on may form spontaneously and accumulate in production water, flotation froth, deposit on mineral surfaces, affecting the flotation performance, and then enter waste waters, mine and natural drainage, polluting soils, surface- and ground waters (Miettinen et al., 2010; Wang et al., 2014). The efficiency of flotation and hydrometallurgical recovery of values, environmental issues are crucially dependent on the state of mineral surfaces. Particularly, it is generally accepted that the surface non-stoichiometry of sulfide minerals induced by oxidation and leaching should affect their hydrophobicity and reactivity, including so-called “passivation”, but the nature of such surface layers are still a matter of controversy (see, for example, Holmes and Crundwell, 2013). Another phenomenon attracting rapidly growing interest in several areas is low-dimensional gas species (“nanobubbles”) at hydrophobic surfaces that may play a decisive role in particle-bubble attachment in flotation but remains scarcely investigated up to now (Xing et al., 2017). Here, we survey our recent results on the abovementioned problems applying a series of rather new methods and approaches; more details can be found in refs. Karacharov et al., 2016; Mikhlin et al., 2015; 2016; 2016a; 2016b; 2016c; 2016d; 2017; 2017a; Vorobyev et al., 2017."

Jan 1, 2018

By S. K. Pan, M. P. Srivastava, N. Prasad

"Dalli mines of Bhilai Steel Plant, India is fully mechanized iron ore mine having wet processing system. It has a capacity to treat 5 Mt of ROM. In processing circuit of Dalli mines, scrubbing, wet screening and classification operation is being carried out. Average slime generation for the last five years is about 14% of ROM. As the mining has reached to the lower benches, fines generation is more. As a result, very fine and heavy particles, which settle fast, are being discarded with the slime to tailing pond. These heavy and faster settling particles were causing jamming in the thickeners.Laboratory investigations were carried out at Research and Development Centre for Iron and Steel (RDCIS) to suggest a suitable scheme to recover high quality fines so that the availability of thickener can improve. The slime samples were first treated in a floatex density separator. The concentrate obtained from the floatex density separator was treated in hydrocyclone. Laboratory investigations indicated that the slime with 49% Fe, 12.7% silica and 10.7% alumina can be upgraded to 62.1% Fe, 3.3% silica and 2% alumina with 36% material recovery. Based on the laboratory studies ,a system was installed at Dalli minesThe general arrangement of the system is shown in Fig. below."

Jan 1, 2003