Search Documents

By Yuta Yamamoto

Seafloor massive sulfides (SMS) which contain Au, Ag, Cu, Zn, and Pb have been interested in as a target of commercial mining these 15 years. Japan has large potential of SMS and a national R&D project for the mining has been active these 5 years. However, the economy of SMS mining is very bad, because the waste tailing disposal cost is very expensive in Japan. A slurry flushing method is experimentally examined in this study for the improvement of the economy. During the flushing, because of density difference between the metal-rich ore and the waste rock, a kind of gravity separation is possible. The results suggest a possibility of the actual application.

Sep 14, 2011

By Robert Corcoran, Piotr Jasiobedzki, Roy Jakola, Michael Jenkin

Vast mineral resources of copper, zinc, cobalt and gold have been identified off the coast of Papua New Guinea at depths exceeding 2,000 meters. Accessing them in a cost effective manner and without destroying the marine habitat requires overcoming numerous technical and operational challenges. Although there are a number of deep-sea mining operations underway worldwide, the depths encountered are significantly less than will be required to mine these ore deposits. To date, only the oil industry has developed technologies for successfully accessing reserves at depths of 3,000m.

By D. S. Cronan

Based on analogy with the Clarion-Clipperton zone, three main factors appear to influence the occurrence of potentially economic nodules in the study area, (i) elevated biological productivity, mainly above 50gCm-2y-l, (ii.) sea floor depth near or below the CCD, (iii) an absence of turbidite sedimentation. These conditions are fulfilled in parts of the following basins, where available data indicate that high grade and sometimes abundant nodules occur. i) The East Central Pacific Basin west of the Line Islands extending to the East Central Pacific Basin north and east of the Phoenix Islands ii) The West Central Pacific Basin west and northwest of the Phoenix Islands iii) The North Penrhyn Basin north of Penrhyn Island Notwithstanding the similarities between the environmental conditions under which potentially economic nodules occur in the Clarion-Clipperton zone and in the areas listed above, such similarities may relate only to present day conditions. During the possibly long periods of nodule formation, environmental conditions may have varied, and the deposits formed under conditions different from those prevailing at the present day. However, the fact that both present day conditions and the deposits in the two areas do show similarities suggests that applying the same genetic model to them has some validity. Possibly, any changes in environmental conditions during the period of formation of the deposits has been similar in both areas. Such uncertainties can only be resolved by a much fuller evaluation of the evolution of nodule deposits in both areas throughout recent geological time.

Jan 1, 1986

By I. V. Kubrakova, O. A. Tyutyunnik, M. L. Getsina, A. M. Asavin

An analysis of noble metals (NM) in natural samples is most problematic. Determination of their traces in geochemical samples, in part, for the purpose of deposit evaluation, is a difficult analytical task. A number of international standard reference materials of rocks and ores, in which NM content is certified, is estimated at a half dozen. For example, in the International proficiency test for analytical geochemistry laboratories (GeoPT), which is held by the Department of Earth Sciences (The Open University, United Kingdom), the data for gold and platinum are observed very rarely, and the results obtained in different laboratories differ on 1-3 orders of magnitude. It is caused by low contents of NM in nature, by a variety of their complex and mineral species, as well as by a complicated matrix composition of platinum-containing objects. Among these objects are ferromanganese ores, enriched strongly with Fe, Mn, Ni, REEs - the elements hampering a precise determination of NM due to a complexity of instrumental inter-element correction. The absence of the reliable methods of NM determination in these ores drastically limits the possibility of deposit evaluation.

By H. Shimoda, K. Tamaki, K. Iizasa, M. Watanabe, K. Okamura

Modern Kuroko-type deposits occur in submarine calderas of island-arc fronts and back-arc rifts in Japan. They occur primarily on or adjacent to caldera boundary faults. Hydrothermal sulfides in the Myojinsho submarine caldera are one of Kuroko-type deposits, but their occurrence is different from other deposits found within the area 200 km2 around the Quaternary volcanic front of Izu-Ogasawara arc.

Aug 24, 2006

By Michael Johnston

Nautilus Minerals is exploring for high-grade gold, silver, copper, and zinc-rich submarine massive sulphide deposits (SMS) within the territorial waters of the sovereign state of Papua New Guinea. Work to date has shown that these systems contain spectacularly high metal grades. To date a total of 88 surface sulphide grab samples have been collected from Nautilus’ Solwara 1 Prospect within EL 1196 in the Manus Basin, returning average grades of 15.5 g/t gold, 191g/t silver, 10.8% copper, and 4.7% Zn. Drilling in January/February 2006 confirmed the presence of this high grade system, with sulphide intersections up to 19m below the sea floor, with a best intersection of 11.6m at 9.1 g/t Au and 13.1% Cu.

The chemical composition of the nodules varies with the type of manganese minerals and the size and characteristics of their nucleus but those who have an economic interest have nucleus, generally : Mn> Fe> 6> Si> Al> Ba> Ni> Cu > Co. The Pacific Rim is an area of abundant occurrence of polymetallic nodules and the Pacific sea floor of the Clarion-Clipperton Zone (CCZ) is one of the most interesting areas in regard to the genesis of polymetallic nodules. Their abundance in the ocean floor is very variable, as there are places where they cover more than 70% of the ocean floor. The nodules can be found at any depth, but the highest concentrations are between 4000 and 6000. Hydrothermal processes that occurs near the East Pacific Rise at 21° N, may inputs metallic elements to nodules and to pelagic sediments, especially in regions close to the dorsal, as a greater influence hydrogenetic processes are present westward Metals such as Cu, Co, Ni, Sn, Fe, Mg, Pb, Zn and Ba show a relationship with the East Pacific hydrothermal activity and sea currents carry these metals in solution to the Clarion-Clipperton fracture area, where there are hydrogenic metals sources (Al, Fe and Mn).

Sep 14, 2011

By Peter E. Halbach

The Central Indian Ridge (CIR), the boundary between the African and Indian plates, forms a SSE trending mid-oceanic accretionary system in the equatorial Indian Ocean (Fig. 1), extending to the northerly Carlsberg Ridge spreading center, and terminating at the Rodrigues Triple Junction (RTJ; 25°30'S, 70°06'E) by intersection with the Southwest Indian Ridge (SWIR) and the Southeast Indian Ridge (SEIR). Crustal divergence of the CIR proceeds at intermediate rates; a progressive increase of ocean floor accretion towards the south is documented: the present half spreading rate and ridge trend change from 1.80 cm/a and N142° at the equator to 2.73 cm/a and N152° north of the triple point. The topography of the central rift zone is rather smooth compared to slow spreading analogues such as the SWIR, but slightly more rugged than the SEIR. The rift valley is 500-800 m deep, 10-15 km wide and usually well defined. The inner floor, 2-4 km in width, is relatively flat along the axis and more variable in cross section, and lies at 2700-3200 m depth. Off set fracture zones striking generally N60° . in southern portions of the CIR and laterally displacing median valleys by as much as 8 km are often bent, uplifting crustal sequences up to several hundred meters. The length of individual spreading segments varies between a few and several tens of kilometers. The vertical displacement on normal faults are larger while lineaments are shorter than those of the faster spreading SEIR. The direction of lineaments measured on the southwestern and northeastern flanks of the southern CIR are N154° and

Jan 1, 1994

By Jelena Milinovic, Sofia Martins, Anna Lichtschlag, Sven Petersen, Fernando J. A. S. Barriga, Bramley Murton, Adeline Dutrieux

"The active TAG hydrothermal mound is one of the largest and better studied. Due to its size (one of the largest, known so far, in the Atlantic Ocean) and concentration of specific economic valuable elements, it might be considered for future exploitation due the increasing demand for raw materials. However, the discovery of several large inactive sulfide mounds, some partially buried under sediments may relieve this pressure. Exploration for such occurrences can, together with geophysical exploration tools, be accomplished by mineralogical and geochemical studies of those sediments.INTRODUCTION AND GEOLOGICAL SETTINGThis study reports the results from sediment samples collected during the Meteor M127 cruise on the TAG hydrothermal area in 2016. The Trans-Atlantic Geotraverse (TAG) hydrothermal field (Mid-Atlantic Ridge, 26°08’N) is located 2.4 km east of the main rift valley at depths of about 3650 m. The TAG hydrothermal field stands as an example of a massive sulfide deposit on a low-spreading ridge associated with an active detachment fault (Humphris et al., 2015).Associated with the TAG hydrothermal field are metalliferous sediments/deposits that can reach several meters in thickness (Metz et al., 1988). These sediments/deposits can be formed by hydrothermal plume fall out (buoyant and nonbuoyant), massive wasting of hydrothermal edifices (sulfide mounds and chimneys) and authigenic mineralization (Gurvich, 2006). By studying the grain size, mineralogy and geochemistry of the sediments it is possible to identify each type of sediments and find their proximal or distal distribution. The location of the gravity cores studied here is distributed along sediment ponds near inactive hydrothermal mounds [Three mounds area (B)], actively venting low-temperature mound [Shimmering mound (A) and Mir zone (D)] and an area of sediment accumulation [Central area (C)] (Rona et al., 1993) (see Figure 1)."

Jan 1, 2017

By Bjørn Eske Sørensen, Kristian Drivenes, Przemyslaw Kowalczuk, Kurt Aasly, Gavyn Rollinson, Ben Snook

Efficient and successful mineral processing is dependent on detailed knowledge of the materials and minerals that are to be separated and concentrated. Common bulk methodologies such as XRD and XRF are fast and easy, and can provide an overview of the mineralogy and bulk chemistry of the material. However, they will not provide any textural information. Knowledge of the often intricate interaction between minerals in seafloor massive sulfide deposits is crucial in plant design for mineral processing. Samples from the Loki’s Castle hydrothermal vent have been characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), optical microscopy, Scanning Electron Microscopy (SEM), QEMSCAN, Electron probe microanalyzer (EPMA), and Electron Backscatter Diffraction (EBSD). Processing experiments used froth flotation and leaching techniques. The typical line of operation in ore characterization is shown in Figure 1. Mineral processing may be commenced after any stage of ore characterization. However, it is ideal to have completed as many steps in the ore characterization as possible in order to have the most information of the initial feed material. The main economic minerals in the samples are isocubanite (CuFe2S3), chalcopyrite (CuFeS2), and sphalerite (ZnS), with minor galena (PbS) and trace amounts of Au and Ag. The minerals show complex intergrowth textures down to the nanometer scale. These samples exemplify the need for advanced microtextural analyses to adequately characterize ore material prior to processing. The complex textures hamper the use of flotation as an efficient technique, due to the inability to sufficiently liberate the different minerals and problems with selectively floating isocubanite. Thus, leaching was the preferred method for extracting metals.

Jan 1, 2018

By Hunsoo Choi, Sung Rock Lee, Ian J. Graham, Ian C. Wright

This is a part of the joint KIGAM-GNS-NIWA 3-year study of ferromanganese modules in the Campbell Nodule Field, east of Campbell Plateau to determine age distribution, growth rates and geochemical evolution in relation to geographic setting. The petrography, chemistry, inferred genesis, and 10Be/9Be dating of the nodules were described in the science report of GNS (Chang et al., 2003a, 2003b; Graham et al., 2003a) and presented at UMI (Chang et al., 2003c; Graham et al., 2003b). The morphology and distribution of ferromanganese nodules were also published in detail (Wright et al., 2005). This presentation is only concentrated on the mineralogy and chemistry of the nodules.

Aug 24, 2006

By James R. Hein

A new data set of cobalt-rich ferromanganese (Fe-Mn) crust chemistry has been completed for the first detailed sampling of a latitudinal crossing of the Pacific equatorial zone of high biological productivity. Samples were collected in January-March, 1999, during the AVON 2 cruise aboard the R.V. Melville, Scripps Institute of Oceanography. Samples were collected from 4.6° N to 9.2° S latitudes along two ridges, the Marshall Islands-Gilbert Islands ridge (4.6° N to 3.5° S) and the Howland Island-Tokelau Islands ridge (1° N to 9.2° S). The two ridges are offset east-west in the region of overlapping latitudinal sampling by about 466 km. We determined the concentrations of 48 elements for 147 samples from 39 dredge hauls taken on 33 seamounts and island flanks that occur between the Marshall Islands to the northwest and Samoa to the southeast. Element concentrations can be examined as varying spatially and with water depth in the ocean and we examine those relationships based on statistical analysis of the chemical and spatial data. The mean Fe/Mn ratio of 1 and mean Co content of 4645 ppm are typical of West Pacific hydrogenetic crusts; but the mean Co content is low compared to those of some equatorial North Pacific sites, such as the Marshall Islands and Johnston Island EEZs. In contrast, the mean Cu concentration (1540 ppm) is 35% higher than the mean concentration for Pacific Ocean Fe-Mn crusts (998 ppm). Another striking difference is the 40% higher Ba concentrations (mean 3107 ppm) compared to typical Central and West Pacific crusts (mean 1876 ppm); but Ba concentrations are lower than those in California continental-margin Fe-Mn crusts (mean 4085 ppm). A final significant difference in Fe-Mn crust chemistry is Zr concentrations, mean 921 ppm (maximum 1523 ppm), which is about 30% higher in this data set compared to the previously determined mean value of 613 ppm for Central and West Pacific crusts. Zirconium has a strong positive correlation with Ba and a weak positive correlation with Mn.

Jan 1, 2003

By Akira Usui, Sayuri Kubo, Satoshi Tokeshi, Shingo Kato, Katsuhiko Suzuki, Teruhiko Kashiwabara

"INTRODUCTIONFerromanganese (Fe-Mn) crusts are a kind of marine chemical sediment composed of Fe and Mn oxy-hydroxides as well as small amounts of clastic sediments, which are ubiquitously found on the surface of slopes of seamounts and oceanic plateaus at depths from 900 to 5500 meters below sea level (mbsl). Fe-Mn crusts contain extremely high concentrations of useful minor metals such as Co, Ni, Te, REEs, and thus are expected as submarine mineral resources. Also, Fe-Mn crusts record the change of chemical compositions of seawater during last several tens million years, which allow us to obtain clues to clarify the paleoenvironmental conditions at the time of its deposition. However, occurrence, chemical compositions, microbial community and growth patterns of ferromanganese crusts are yet fully understood. Hence, a comprehensive study on the genesis of ferromanganese crusts, such as growth rates and enrichment processes of elements, is required to better understand their resource potential as well as their applications to paleoceanographic study.Based on the resource potential of ferro-manganese crust, the project entitled “Next- Generation Technology for Ocean Resources Exploration” was launched as one of the governmental projects to develop the exploration technology based on the scientific research on the submarine resources such as hydrothermal deposits (e.g., a poster by Kawada et al.), ferro-manganese crusts. We have made several research cruise to seamounts in the north-western Pacific such as Takuyo-Daigo and Takuyo-Daisan seamounts (Fig. 1) ."

Jan 1, 2017

By Alexander Malahoff

The most exciting frontier in Ocean Technology is represented by a new class of Marine Bioproducts, the source of which lies in marine microorganisms. The microorganisms include microalgae, bacteria and archaea. These organisms represent very diverse, adaptive life forms and in their metabolic processes use carotenoids, polyunsaturated fatty acids, ultraviolet blockers, as well as a wide range of enzymes that are pivotal in the production of new pharmaceuticals and nutraceutical products. These organisms cover a wide spectrum of ocean environments, from the shallow to the deep, from the normal to the extreme. The technological challenge is in the identification of candidate organisms, in the screening for valuable enzymes, and in the industrial production. A whole new range of collecting strategies involving submersibles, ROVs and in situ ocean floor instrumentation is emerging. New non-polluting industrial chemical processes involving the use of photobioreactors and extremophile bioreactors for breeding and monitoring these organisms in neo-farming technology is emerging. The commercial value of these candidate products is immense, as is the range of potential organisms. The dimension of this new industry is global. The Marine Bioproducts Engineering Center (MarBEC), funded by the National Science Foundation (NSF), has been established at the University of Hawaii. The vision of MarBEC is to develop a seamless research system stretching from undergraduate education to industry for the purposes of producing valuable marine bioproducts outside of the normal chemical factory production. MarBEC is uniquely and strategically placed in the Pacific to explore, find, and adapt highly bioactive marine micro-organisms found in the tropical ocean. We have watched the increasing need by the ever-

Jan 1, 2000

By Thomas Kuhn, Anna Wegorzewski

"INTRODUCTIONPolymetallic nodules from the Clarion and Clipperton Zone (CCZ) within the equatorial NE Pacific Ocean show high concentration of economic important strategic metals such as Ni, Cu, Co, Mo and Rare Earth Elements (REE). The content of those metals in nodules is depending on (i) the supply during individual growing periods, (ii) the environment conditions as well as (iii) on different manganese minerals, which occur in nodules. The incorporation of the metals can vary within the structure (incorporated into the structure / over vacancies of the structure) and this can be relevant for the further metallurgical treatment.Mineralogy of Mn-nodules from the CCZ and the incorporation of metalsManganese nodules consist of nm to µm thick layer growth structures (LGS) of different genetic origin (hydrogenetic/suboxic-diagenetic). Those LGS form due to the precipitation of Mn-and Fe-(oxy) hydroxide colloids from the oxygen rich near-bottom water and/or pore water (hydrogenetic growth; Halbach et al., 1988) or from suboxic (depleted in O2 <5µmol O2/l; Hein and Koschinsky 2013)) near-bottom water/pore water (suboxicdiagenetic growth; Halbach et al., 1988; Wegorzewski and Kuhn, 2014).In general, metals dissolved in seawater will be adsorbed and complexed on the oxide surfaces according to their different surface charge. The surface charge of the Mn-Fe (oxy) hydroxides depends on the pHzpc (zpc: zero point of charge). In seawater dissolved hydrated cations (Ni2+, Cu2+, Co2+) are adsorbed preferentially on the negatively charged Mn-oxide (MnO2 -) surface (pHzpc 2.8). In contrast, negatively and neutrally charged complexes (e.g., Ti(OH4); REE(CO3)2 -, MoO4 2-) are adsorbed on the surface of Fe-oxy hydroxide colloids (FeOOH+) which have a slightly positively charged surface (pHzpc 8.5; Stumm and Morgan, 1981; Koschinsky and Halbach 1995)."

Jan 1, 2017

By Lu Jun

Up to now, much data on marine minerals, as well as on marine geochemistry, have been accumulated. Modem computer databases provide optimum flexibility and power for manipulating these data. The best worldwide marine mineral database is currently the Marine Minerals Bibliography and Geochemical Data Base created by Carla Moore et al. at the National Geophysical Data Center in the United States. In fact, in the course of studying marine minerals and geochemistry we may collect not only digital-character type data but also graph and image (black-white, grey and color image) data types. For instance, correlation diagram between chemical compositions of minerals, spectroscopic graphs, (e.g. infrared spectra, Mossbauer spectra, etc.), grey or color images from both optical and electron micro- scopes (scanning or transmission electron microscopes) as well as seabed photographs. Charles L. Morgan et al. (1993) reported that 10,000 photographs and some video images of the seabed in the Clarion-Clipperton region of the northeastern tropical Pacific have been collected by the Ocean Minerals Company. If both graphic and analytical information were stored in a database, it would be very useful and convenient to marine geologists. This system would not only be able to search for all the data based on one parameter, but also for both size and composition distributions. If possible, geostatistical methods could be combined with fractal dimensional methods. Of course, this would require enormous efforts. Before multimedia technology emerged, it was very difficult to create image databases. The emergence of large-capacity compact discs, high-speed central processing units, and high-speed digital signal processing techniques makes it possible to establish multimedia database management systems (DBMS), image-text DBMS, that involves graphs, text, images, and sound. In order to store image fields in a DBMS, we have to take into account two problems: (1) image access format and (2) image compression code standard.

Jan 1, 1994

By Tetsuo Yamazaki

The Kuroko-type seafloor massive sulfides (SMS) in the western Pacific have received much attention as sources for economic recovery of gold (Au), silver (Ag), copper (Cu), zinc (Zn), and lead (Pb). Since the end of the 1980s, the Kuroko-type SMS have been found in the back-arc basins and on oceanic island-arc areas. In Okinawa Trough (Halbach et al., 1989) and on the Izu-Ogasawara Arc (Iizasa et al., 1999) are the typical representatives in the Japan’s EEZ. They yield a higher concentration in Au and Ag than the SMS found in ocean ridge areas (Rona, 1985). Similar formation processes with the Kuroko ore deposits on-land in Japan have been expected and outlined by many researchers (Sillitoe, 1982; Scott, 1985). The higher Au and Ag contents have increased the chances for profitable mining operation, which is under consideration by a private company (Malnic, 2001). Information about the resource potential of the targeted Kuroko-type SMS deposit, such as the amount of SMS ore body, the inside structure, the mean metal yields, and the geographical details are necessary for a technical and economic validation analysis for the development. The Sunrise Deposit of Myojin Knoll on Izu-Ogasawara Arc in the Japan’s EEZ is selected as a target for the technical and economic validation analysis. The relatively higher amount of information on its resource potential is the reason why the deposit is selected.

Sep 24, 2006

By Mark D. Hannington

Seafloor polymetallic sulfides have been found in diverse volcanic and tectonic settings on the ocean floor at water depths ranging from 3700 meters to <1500 meters. More than 100 occurrences of hydrothermal mineralization have been documented (including Fe-oxide deposits, Mn-crusts, metalliferous sediments, and massive sulfides), but high-temperature hydrothermal activity and large accumulations of polymetallic sulfides are known at fewer than 20 different sites. Chemical analyses of samples from these deposits indicate that they contain important concentrations of Cu, Zn, Ag, and Au, comparable to those of massive sulfide deposits on land. However, the lack of sufficient data concerning the distribution, size, and bulk composition of seafloor deposits precludes a meaningful assessment of their resource potential.

Jan 1, 1994

By M. Geoghegan

Under the provisions of the U.N. Law of the Sea Convention Ireland is likely to have mineral rights to an area of continental shelf some six times its present land area. Apart from the major potential hydrocarbon basins which are currently the focus of active commercial exploration, little is known about the mineral resources of this vast area. In recent years a variety of mineral resources however have been identified from the coastal region. These include Sand and Gravel aggregates, Calcaraeous Algae (Lithothamnion), Heavy Mineral Sands and Coal deposits. The potential also exists in the coastal zone for buried placer deposits and base metal deposits. Several million cubic metres of gravel and hundreds of millions of cubic metres of sand have been identified by the Geological Survey of Irelands (G.S.I) Marine Unit off the east coast. The greater part of these deposits lies within the 10 metre depth contour and are easily recoverable. Irish aggregate needs at present are well supplied by onshore Pleistocene glacial deposits. Commercial interest in offshore deposits is in supplying coastal areas which are locally poor in aggregate and major coastal construction works. The possibility of supplying the large British and Continental European Market nearby also exists.

Jan 1, 1988

By Andrew G. Hudson

The long-term economics of each of the four principal metals in marine manganese nodules (copper, nickel, cobalt and manganese) was evaluated to determine the anticipated viability of a nodule mining venture based on existing studies of the potential profitability of a nodule project. This included assessments of the lifetimes of land-based reserves, and examination and econometric modelling of the economic variables thought to affect nodule metal prices and demand. These analyses demonstrated that a) land-based reserves of the nodule metals were likely to last well into the future (100 400 years); b) average nodule metal paces were likely to stay a low levels for the foreseeable future; and c) the expected revenue stream from a twenty- ear nodule mining venture was substantially (42%) below that required to attract the necessary investment capital for such a high risk venture.

Jan 1, 1996