Search Documents

By Alex Grenoble, Alex Reeb, George Filz, Farzad Abedzadeh

"This paper summarizes available information on the characteristics and properties of deep-mixed soilcement produced by the wet method. The topics covered in this paper include: unit weight, unconfined compressive strength, strength variability for field mixed materials, influence of curing time, influence of consolidation pressure, Young’s modulus, differences in strength and stiffness between small and large samples, creep deformations, Poisson’s ratio, and tensile strength. In addition, this paper discusses the development of design considerations and recommended property values for a project that uses soilcement to protect an existing dam penstock from loads applied by an overlying stability berm. Some of the key recommendations for the deep-mixed soil-cement to be used in this project are that (1) a curved strength envelope that includes tensile strength can be used in the analysis, (2) the stress-strain and strength properties can be characterized using Duncan and Chang's (1970) hyperbolic model, and (3) a specification based on the median unconfined compressive strength value is appropriate.INTRODUCTIONFor many projects, including foundation and embankment support, deep mixing can be designed based on simplified procedures and following standardized guidelines (e.g., FHWA 2013). However for unusually complex or critical projects, it is often necessary to perform numerical analyses, and in order to perform these numerical analyses well, a thorough understanding of the material properties is needed.This paper summarizes information on the characteristics and properties of deep-mixed soil-cement produced by the wet method, and it discusses the development of design considerations and recommended property values for a specific project, herein referred to as the penstock project, that requires numerical analyses. For the penstock project, a horseshoe-shaped enclosure of soil-cement is being considered beside and above an existing dam penstock to protect it from loads applied by an overlying stability berm that will be constructed for seismic remediation. The concept is to use soilcement created by the deep mixing method along the sides of the penstock and to use compacted soilcement above the deep mixing to create the crown of the protective soil-cement zone around the penstock. For this application, the soil-cement stiffness, rather than its strength, is the controlling design parameter. To achieve the necessary soil-cement stiffness, the strength will be high enough that the factor-of-safety values against instability along potential failure surfaces passing through the soil-cement are high. Following conventional practice, the soil-cement acceptance criteria will be based on the unconfined compressive strength, and the specified strength will be selected to produce the desired modulus value."

Jan 1, 2015

By Charles R. Conlon, Matthew J. Niermann

This paper presents the underpinning and excavation support systems used for construction at 2100 L Street in Washington, DC. The excavation for the proposed building extended below bedrock, which presented significant challenges for underpinning the historic Stevens School, constructed in the late 1800’s. The Stevens School was underpinned using several techniques consisting of soil mixing below an unreinforced foundation, traditional hand-dug pits to rock, micropiles below rock, and bracket piles. The excavation support system for the remainder of the project consisted of soldier piles and lagging supported laterally by tiebacks and braces. Shotcrete and rock bolts supported the exposed bedrock. This paper will discuss the design, construction and monitoring results.

By Fred Fuchs

"Most deep foundation work is either unseen by the general public or viewed as an inconvenience in their daily lives. Hurricane Katrina changed that perspective for everyone in New Orleans — and many other people in the U.S. and abroad. The public and the government of south Louisiana, and the U.S. Army Corps of Engineers (USACE), all needed to restore trust in the system that protects their property and, more importantly, their lives. While much has been written about the failures of government agencies, in this case incredible solutions were devised and implemented despite daunting schedules and arduous conditions. These solutions were achieved through collaboration, and through the efforts of USACE, where the goal was to fi nd the most expeditious and effective design/build solutions. This disaster thrust the pile driving industry into the national spotlight. Boh Bros. Construction Co., L.L.C., along with numerous local and national heavy construction companies, subcontractors, material suppliers and government agencies, take pride in the milestones reached after Hurricane Katrina.The majority of New Orleans’ population lives below sea level. Historically, the city has been protected by a fl ood control system consisting of earthen levees and I-walls (steel sheet pile topped by vertical concrete wall). Rainwater is pumped out of the city over this protection system and into canals that feed into Lake Pontchartrain. On August 29, 2005, when Hurricane Katrina made landfall just east of the city, the levee system experienced a major failure of several I-walls lining the outfall canals, causing flooding of 74% of the east bank of the city. The counterclockwise rotation of the wind pushed the lake water onto the south shore, raising the level of water more than 10 ft (3 m). A failure of 450 ft (137 m) of floodwall lining the east side of the 17th Street Canal caused extensive damage. This breach prevented the use of the pump stations that outfall into the 3-mile (4.8 km) long 17th Street Canal."

Jan 1, 2008

By Wolfgang G. Brunner

In the far north of Uttar Pradesh Province in the Indian Himalayas, the 280 MW Dhauliganga hydroelectric power plant is under construction by National Hydroelectric Power Corporation (NHPC), a state- owned enterprise, and a joint venture of Kajima Corporation of Tokyo and Daewoo Corporation of Seoul. This project sets out to develop the lower section of the mountain cascade of the Dhauliganga River, a tributary of the Sarda River, with a 311 m gross head. The 1360 km2 mountainous catchment area is bounded in the north- east by the Chinese border and in the south- east by the Nepalese border. The dam project is located in a remote area north of the principal town of Darchula of the upper Sarda valley, which is one of the seismically most active regions of India. The 56 m high rock fill dam, which will be the first of its kind in India, is faced with concrete and has a 1 m thick, at its crown 270 m long and over 70 m deep cut- off wall of plastic concrete below its toe. The cut- off wall, with a total area of 7500 m2, is constructed by a combination of Bauer hydraulic grabs, assisted by chisels and a Bauer BC 40 cutter which enables the overlapping joint system to be installed, guarantees optimum verticality and enables the cut- off to be keyed into the bedrock formation.

Jan 1, 2004

By Michael Cianchetti, Nadir Ansari, Matthew Janes

"PROJECT DESCRIPTIONThe R C Harris Filtration Plant underwent an expansion to install an underground sludge treatment capability consisting of a series of underground tanks within stepped excavations 12m (39 ft) and 10m (33 ft) deep into compact, wet sands over stiff clays and clayey silts.Concerns regarding the original structure influenced designers to set the lateral deflection limit for the proximal front footing at 4mm (1/6 in), (0.03% excavation depth). The design-build team indicated at the time of tender that the movement criteria was unattainable using the tender design. Through extensive Fast Lagrangian Analysis on Continua (FLAC) and a novel construction geometry the design-build team crafted an alternative that produced significant savings over the original concept and met deflection concerns.GEOTECHNIQUEThe hillside site drops 14.5m (47.6 ft) over a distance of 53m (174 ft) between the existing Filter Building on the north and the Services Building on the south. The soils adjacent to the Filter Building consist of 6m (20 ft) of sandy fills, to the footing elevation, over compact sands and layered dense sands and silts to a depth of 10m (33 ft) below existing footing. Beneath the silts lies a 10m (33 ft) thick stiff clayey silt, 2m (6.6 ft) of sandy silt till (containing cobbles and boulders) and an artesian gravelly sand at a total depth of 30m (98.5 ft).The tender information was deemed inadequate to accurately determine soil parameters for a finite element analysis. As a result, the design-build team performed pre-tender Cone Penetrometer Testing (CPT), including dynamic analysis. The CPT data indicated stratigraphy consistent with the conventional bore hole exploration (SPT results) however, the CPT data provided consistently superior soil strengths. The CPT data indicated the sands and silts were dense to very dense throughout their full thickness. The clayey silts below the sands were found to have shear strengths in the 100 to 200 kPa (14.5 to 29 psi) range with an Over-Consolidation Ratio (OCR) ratio of 1.5 to 2. The dynamic analysis, while low strain, indicated very competent behavior with Young’s Modulus values in the 200 to 350 MPa (29,000 psi to 51,000 psi) range. The CPT derived shear moduli and OCR values were vital in determining the soil engineering parameters used for the FLAC analyses."

Jan 1, 2007

By W. G. K. Fleming

Mr P. Bermingham introduced paper 9.1, describing the development and trials of a new pile load-testing technique that the Authors had termed "Statnamic". The system involved launching a test weight mounted on the head of the pile by igniting chemical fuel in a pressure combustion chamber between the pile head and the test weight. The expansion products from the burning fuel generated large pressures which were used to launch the weight upwards at high velocity. The reaction from this force generates an equal and opposite force at the pile head. This force is typically of much longer duration compared with, for instance, dynamic load testing by drop hammer. In addition the pile experiences a much lower acceleration - typically of less than one g. Because of the long duration blow, the pile is loaded at below its natural frequency and is therefore under a uniform high stress over its full length throughout the duration of the test. The pile behaviour is not dominated by the complex action of an impulsive stress-wave as with standard dynamic testing. The test technique is thus essentially quasi-static. It was anticipated that a ram test weight of 16 tonne would be sufficient to provide the test reaction for a 600 tonne load test. It was pointed out that the device was still at the research stage, but had yielded encouraging results to date. Testing would proceed from model testing and computer simulation to full scale field testing.

Jan 1, 1991

By James Walters, Samuel Sideras, Kathryn Petek

The Oregon Department of Transporta­tion {ODOT} is currently performing a seismic retrofit and widening of the Abernethy Bridge as part the 1-205: Stafford Road to OR213 Improvements Project. The Abernethy Bridge, located in Clackamas County, conveys traffic over the Willamette River between the cities of West Linn and Oregon City. The existing bridge structure was completed in 1971 and is approximately 2,700 ft {820 m) in length and consists of 14 piers and two abutments, not including on­and off-ramp structures. At the bridge ocation, the Willamette River is approximately 1,050 ft {320 m) wide. The main channel crossing structure comprises three spans up to 450 ft (137m) long supported on Piers 3 through 6. The west approach structure includes nine continuous spans up to 195 ft {60 m) long and supported on Piers 6 through 14 and Abutment 2. The existing bridge piers are supported on a combination of driven steel H-piles and shallow foundations bearing on basalt bedrock. Construction of the bridge widening and seismic retrofit began in July 2022, which will add one lane in each direction and increase the width of the existing bridge from 100 ft (30 m) to 140 ft {43 m). The seismic retrofit will improve bridge performance to con­temporary seismic design standards and feature a two-level seismic design approach including both operational and life safety design and performance criteria. The foundation design for the project was driven by the highly variable geologic conditions across the project alignment, site constraints and the significant seismic demands. To meet the seismic performance criteria, the foundation solutions for the widening and seismic retrofit included micropiles, ground improvement and drilled shafts up to 12 ft (3.6 m) in diameter. This article describes the foundation design process and methodology and the foundation mitigation solutions developed for the project, as well as discussion of using 12 ft {3.6 m) diameter drilled shafts to mitigate the impacts of deep-seated permanent soil displacements.

Sep 1, 2024

By Allen Cadden

The type of soil we had was a silty fine sand. It had been placed by hydraulic methods in 1904 so it was quite clean I would say less than 10% silt the rest of it was very loose sand. That I'm not certain, I've only done it on sandy soils but it would stand to reason that some sort of a number should apply because you are measuring the amount of work that you are doing to it so if the soil is fairly consistent over the site it should be able to generalize from there but I don't know for a fact that it works. Well, verifying to ourselves that this method actually worked because we weren't certain at first when we were doing it so then we would develop the numbers and then check the results.

Feb 10, 2003

"What can we do in ground engineering to reduce damage to the environment, to repair historic pollution, to reduce our demand on basic resources and to reduce the carbon footprint of our industry? Some developments in geotechnical engineering are already heading in the right direction. These include reductions of ground pollution from grouting, improved dewatering procedures and advances in mix-in-place processes, ground improvement and jet grouting.There is increased interest in certain promising technologies (for example, drilled partial or full displacement piles), but this approach remains for the moment somewhat avant-garde. These piles require substantially greater power to install, and the overall sustainability balance for general application has yet to be shown to be in their favour. They are particularly suited to polluted sites where the problem of dealing with spoil would be costly and where, in the past, driven cast in-situ piles would have been employed. Drilled displacement piles offer some environmental benefit over driven piles in that they cause far less drawdown of potentially contaminated near-surface ground into sensitive, underlying aquifers.There is also great interest in various means of increasing the frictional capacity of bored piles, both conventional auger and continuous flight auger (CFA) piles, by threading or ribbing the soil/pile interface. The increase in adhesion capacity allows reduction in the pile dimensions necessary for a specific load. This obviously leads to less construction waste, but also to less permanent material consumption in the piles and also in the pile caps.The role of ground improvement remains significant for brown land sites and lower capacity foundations. Information technology (IT) has improved the quality assurance of stone column construction, for example. From the sustainability point of view, this is a good news method; here is no cement, no pollution and little obstruction to future redevelopment. We now need to introduce recycled crushed materials instead of natural aggregate as general practice and the technique’s green credentials will be really compelling."

Jan 1, 2009

"TREVIICOS CorporationINTRODUCTIONThe Walter F. George lock and dam was constructed on the Chattahoochee River between 1955 and 1963 with the double function of improving navigation and generating power. Its 82 ft. by 450 ft. (25m x 137m) lock can accommodate large barge traffic and its four generating units with a plant capacity of 150 MW have an average energy output of 453,000 MWH. The dam consists of a 1,496 ft. (456m) long concrete structure housing the spillway, a non overflow portion, the power units and two earthen wing dams extending to the Georgia and Alabama sides, respectively 5,810 feet and 6,130 feet long (1770m and 1868m). As soon as the reservoir was impounded it became apparent that excessive seepage was occurring. From 1962 to 1985 a series of remedial works was performed using several techniques, but the problems continued under the dam, jeopardizing its generating potential and possibly undermining its stability.Finally, the decision was made to construct a deep cutoff primarily under the concrete portion of the dam to remedy the problem. PROCUREMENTOn July 5th, 2001 best and final offers were solicited by the Corps of Engineers (COE) for the construction of a deep cut-off to be built in front of the concrete portion of the dam from the bottom of the lake and tied into it. The cut-off had to cross an existing lock structure and an underwater retaining wall, as well as the remnants of a steel coffer cell left in place from the initial construction.The specifications required that the wall be built with a minimum thickness of 24” (600mm) and that it extended from the bottom of the lake to elevation -5 (1.52m) into the Providence formation, an impervious layer.While the land portions of the wall were on average 208 feet (63.4m) deep, the marine portion started from up to 90 feet (27m) of water and continued through different rock formations for another 100 feet (30m).Contractors were invited to propose their own method of constructing the cut-off and offers would be evaluated using several criteria, including technical, economical, organizational and experience.Three proposals were received and on August 14, 2001 an award was made to the Joint Venture (JV) of Treviicos and Rodio."

Jan 1, 2014

By Monique Nykamp

"INTRODUCTIONTerminal 46 is located just south of downtown Seattle, and is one of the Port of Seattle’s busiest container terminals. The Terminal 46 Redevelopment Project was undertaken to replace the existing 15-m-wide (50 ft) cranes along the apron with 30-m-wide (100 ft) cranes, which can unload larger, post- Panamax ships. The project included upgrading the existing waterside crane rail with new piles and constructing a new land-side rail behind the sheetpile bulkhead. The new piles had to be installed adjacent to the existing apron without causing damage, which was a signifi cant geotechnical challenge due to the soft soil conditions at the site. An instrumentation program performed during the test pile program evaluated this challenge and allowed for the development of specifi c production pile installation procedures that had the least possible effect on construction costs and schedule. SITE HISTORYThe site lies along the west side of Elliott Bay, north of the mouth of the Duwamish Waterway. Prior to development, this area was part of the tide fl ats where the Duwamish River drained into Elliott Bay. Prior to 1970, there were several existing timber piers and structures in the area. In the 1970s, the Port of Seattle constructed a 900-m-long (3,000 ft), 30- m-wide (100 ft) apron to support fi ve, 15-m-wide (50 ft) container cranes. The contained backland area was then fi lled with dredged spoils (sand and silt with organics) and the upper 5 to 20 m (16 to 65 ft) backfi lled with sand and gravel.The existing apron was constructed using 0.4 m (16 in) octagonal prestressed concrete piles to support the precast concrete deck and crane rails. The pile-supported bents were spaced at 6.1 m (20 ft), center-to-center, along the longitudinal direction. Pile lengths typically varied from about 20 to 40 m (65 to 130 ft) with 15 to 26 m penetration below mudline (50 to 85 ft penetration). The slope below the apron was constructed at about 1.75 horizontal to 1 vertical to allow for suffi cient water depth for cargo ships. In most areas, a riprap buttress was placed at the toe of the slope. A typical cross section of the apron is shown on Figure 2.Several stability, settlement and pile driving issues arose during the original construction of T-46 (Pita, 1983). Reportedly, movement of the submarine slope occurred during pile driving, resulting in settlement behind the bulkhead. Pile driving reportedly caused settlement of adjacent piles. In addition, some piles were “running” (dropping quickly under one hammer blow) during installation."

Jan 1, 2007

By Monique Nykamp

"INTRODUCTIONTerminal 46 is located just south of downtown Seattle, and is one of the Port of Seattle’s busiest container terminals. The Terminal 46 Redevelopment Project was undertaken to replace the existing 15-m-wide (50 ft) cranes along the apron with 30-m-wide (100 ft) cranes, which can unload larger, post- Panamax ships. The project included upgrading the existing waterside crane rail with new piles and constructing a new land-side rail behind the sheetpile bulkhead. The new piles had to be installed adjacent to the existing apron without causing damage, which was a signifi cant geotechnical challenge due to the soft soil conditions at the site. An instrumentation program performed during the test pile program evaluated this challenge and allowed for the development of specifi c production pile installation procedures that had the least possible effect on construction costs and schedule.SITE HISTORYThe site lies along the west side of Elliott Bay, north of the mouth of the Duwamish Waterway. Prior to development, this area was part of the tide fl ats where the Duwamish River drained into Elliott Bay. Prior to 1970, there were several existing timber piers and structures in the area. In the 1970s, the Port of Seattle constructed a 900-m-long (3,000 ft), 30- m-wide (100 ft) apron to support fi ve, 15-m-wide (50 ft) container cranes. The contained backland area was then fi lled with dredged spoils (sand and silt with organics) and the upper 5 to 20 m (16 to 65 ft) backfi lled with sand and gravel.The existing apron was constructed using 0.4 m (16 in) octagonal prestressed concrete piles to support the precast concrete deck and crane rails. The pile-supported bents were spaced at 6.1 m (20 ft), center-to-center, along the longitudinal direction. Pile lengths typically varied from about 20 to 40 m (65 to 130 ft) with 15 to 26 m penetration below mudline (50 to 85 ft penetration). The slope below the apron was constructed at about 1.75 horizontal to 1 vertical to allow for suffi cient water depth for cargo ships. In most areas, a riprap buttress was placed at the toe of the slope. A typical cross section of the apron is shown on Figure 2.Several stability, settlement and pile driving issues arose during the original construction of T-46 (Pita, 1983). Reportedly, movement of the submarine slope occurred during pile driving, resulting in settlement behind the bulkhead. Pile driving reportedly caused settlement of adjacent piles. In addition, some piles were “running” (dropping quickly under one hammer blow) during installation."

Jan 1, 2007

By S. Chilka, I. Maloney, J. Brady

"The purpose of this project was to design the Electrical Service Platform (ESP) for the Cape Wind Offshore Wind Farm. The ESP structure comprises two primary parts: the topside platform housing the electrical equipment and the two jacket substructures providing foundation support to the platform. The topside is supported only by the two inner legs of each jacket. The site water depth is relatively shallow and the seabed comprised of loose sediment subject to severe local scour up to 18 feet. The piles are designed for local scour, storm conditions, vessel impact, ice loads and pile installation fatigue. This paper focuses on the design and construction aspect of this project.PROJECT DESCRIPTIONBackgroundThe Cape Wind project will be located in Nantucket Sound between Cape Cod on the Massachusetts mainland (northeastern coast of the USA) and the Islands of Martha’s Vineyard and Nantucket (Fig. 1). The project is to be sited on Horseshoe Shoal, about equal distances from the mainland and the two islands. The project will produce 75% of the electricity used on Cape Cod and the Islands of Martha’s Vineyard and Nantucket with zero pollution emissions and resulting in the reduced operations, fuel consumption and pollution emissions from the fossil fuel power plants in the region. The wind farm, if constructed per plan, is expected to be America’s first offshore wind farm.The wind farm will consist of an array of 130 Siemens 3.6-megawatt offshore wind turbines with a combined production capacity of 468-megawatts. The offshore wind turbine towers will be bolted onto the transition pieces supported by monopile foundations driven into seabed. The power from the 130 wind turbine generators will be delivered to the Electrical Service Platform (ESP) by an array of up to 14 seabed conductors."

Jan 1, 2017

By Peter Yen

This session consists of five papers. Three involved research on the properties of grout materials, specifically ultrafine cements and polyurethane grouts. Two papers present the development of soil grouting technology and monitoring methods. Of great interest are the papers on ultrafine grout penetrability testing focusing on the pressure filtration effects encountered in permeation grouting applications (Ericksson, Stille and Mittag, Savidis). The comparison testing of hydrophilic and hydrophobic polyurethane grouts submitted by Vrignaud, Ballivy, Perret and Fernagu assessed the long-term performance of these materials for repairing saturated cracks in concrete, subject to thermal expansion and contraction. Two very practical papers present the development of soil grouting, where permeation, fracture, replacement, jetting and other grouting techniques are utilized. The papers by Lees with Chuaqui and Warner present experience with ultrafine and other commonly used grout materials. Methods to measure and monitor the injection process and verify production progress are discussed.

Feb 10, 2003

By William B. Conway

This paper will describe the large caisson pier foundations for four of the bridges crossing the Mississippi River in the New Orleans area; and will discuss some of the unusual problems encountered during their sinking. Certain settlement phenomena experienced during their service life will also be related: The four bridges in order of their construction: The Huey P. Long Bridge, River Mile 106.1, completed in 1935 The Greater New Orleans Bridge No. 1, River Mile 96.0, completed in 1958 The Hale Boggs Bridge, River Mile 121.6, completed in 1983 The Greater New Orleans Bridge No. 2, River Mile 96.1, completed in 1988 Each of these bridges employed large open-dredged concrete caissons as foundations for one or more of the river piers, with the smallest being the 65ft by 102ft caissons for Piers I and II of the Huey P. Long Bridge and the largest being the 99ft by 214ft caisson for Pier II of the Greater New Orleans Bridge No. 2. The Huey P. Long caissons are founded in a dense fine sand at -170 while all of the other bridge caissons are founded in hard preconsolidated clay at elevations varying from -150 to -185. The Huey P. Long Bridge is currently being widened without increasing the caisson foundations under any of the river piers; and the design reasoning that led to this decision is presented.

Jan 1, 2013

By Andreas Andenæs, Arne Schram Simonsen

"AbstractThe Tresfjord bridge is with its variety in foundation concepts and difficult soil conditions one of the most geotechnically challenging projects in Norway at the time. The project comprises design of large concrete caissons, steel core piles through large rock fills, and closed end steel pipe piles in up to 40m water depth driven in very hard moraine. Test piling has also been conducted to check feasibility of the concept, and PDA measurements have been used to verify sufficient capacity of piles. FactsThe Tresfjord bridge is part of the new export road from Ålesund to Åndalsnes on the North-West coast of Norway built by the Norwegian Road Administration. The bridge will reduce travel time with about 30 min between the cities, see Figure 1. The bridge is planned to open summer 2015.The Bridge crosses the Tresfjord and will be 1290 m long. The bridge is built as a free cantilever bridge and will be resting on a total of 20 nos. of foundations, where two are abutments resting on steel core piles, three are casted directly on bed rock and 13 are foundations resting on steel pipe piles. The last two foundations holding the main span will be concrete caissons resting on bed rock and moraine. Figure 2 shows a 3D model of how the finished bridge will look. Multiconsult AS is responsible for design and pile supervision , while the Joint-Venture Bilfinger-Tresfjordbridge ANS is responsible contractor.Soil ConditionsPercussion soundings and sampling together with coring have been performed in the individual foundations using a small geotechnical equipped vessel. Acoustic and refraction seismic profiling have also been carried out to tie in the layers between the boreholes.The soil conditions are varying over the length, but are in general dominated by a soft top layer (2-4 m) of sediments over very hard moraine with occasionally large boulders. Piles in the two foundations closest to shore on the western side of the bridge are piled to bed rock with penetrations up to about 27 m in soil.Water depth varies from about 10 to 40 m for the piled foundations. Figure 3 show how the topography of the seabed varies over the bridges length."

Jan 1, 2014

By Sathya Subramanian, Jun Yuan Ryan Lee, Angelina Yi Tian Theng, Kai En Low, Soon-Hoe Chew, Yeow Chong Tan, Kai Yang Toh, Pei Ling Goh

Conventional Quality Assurance and Quality Control (QA/QC) methods for Cement Bentonite (CB) walls rely on destructive coring, which is carried out at specific curing times like 28 days or 91 days. The key parameters determined are strength and permeability. Hence, the conventional methods will not be able to give any indication on strength and permeability until later stage of curing. This delayed QA/QC hinders quick remediation when unsatisfactory strength or permeability values are obtained. To address this limitation, this study utilizes non-destructive resistivity monitoring system to provide indications of the parameters at early days of curing. By continuously assessing resistivity of CB at various depths, this method aims to provide predictive indicators of long-term strength and permeability, enabling proactive interventions before the conventional 91-day coring, if needed. A comprehensive case study is presented, which includes scaled model in a laboratory, as well as a actual measurement in the field. The large-scale laboratory setup models the actual thickness of the CB wall in the field (0.8 m). Specially designed and fabricated resistivity devices are installed in the laboratory setup, and two sections in the field CB wall. Findings show that in terms of resistivity development with curing time, the field resistivity continuous monitoring data displays a similar trend to those resistivity measurements conducted in the laboratory-scaled model. Cored samples were also taken in the laboratory and field at specific curing time of 91 day. The resistivity correlated well with the cored samples’ strength and permeability values. 

Oct 7, 2024

By Jeff Wilkinson, Brandon Walter

"A&N Electrical Cooperative provides electrical service to the counties of Accomack and Northampton along Virginia’s Eastern Shore and to Smith Island in Somerset County, Md.A&N recently worked to improve the efficiency of power distribution to a small island community and marina on Tangier Island in the Chesapeake Bay. This improvement consisted of upgrading the existing distribution substation with a new 25 kV 2-bay box distribution structure. Earth Contact Products (ECP) collaborated with PowerServices, Inc. (PSI) to design and install a helical foundation support system as part of the substation upgrade. Feasibility EvaluationThroughout the design process, A&Nworked with its partners PSI (design) andT&D Solutions (installation) to identifycost-effective alternatives. Foundationsystems considered included cast-in-placereinforced concrete caissons, precastconcrete foundations, driven steel piles and helical piles. In evaluating all of theoptions, the greatest concern was gettingthe material onto the island, followedclosely by the availability of the equipmentto install the foundations. Clearly, cost,more specifically the installed cost, was asignificant consideration and decisionfactor throughout the process.There were several limiting factors that had to be considered during the design process, the most significant of which was that all of the material had to be barged to the site. With traditional reinforced concrete deep foundations in mind, the cost for installing these piles was projected to be nearly $2,000/cu yd ($262/cu m) of installed concrete. Given that approximately 5 to 6 cu yd (3.8 to 4.6 cu m) of concrete would be required for this structure, the cost was significantly high for this project. What’s more, because the components of the concrete mix would have to be barged and then hand mixed on site, there was concern regarding both the time required to complete the piles and the quality of the installed concrete. For the driven pile alternative, the availability, or lack thereof, of equipment and material cost resulted in a total cost estimate that was more expensive than that of the concrete piling alternative. The high material cost for the piles, which was more than double than the cost of concrete, was due to the number and size of piles needed to resist the overturning moment. Ultimately, the team selected the helical pile alternative. The decision to a use helical pile foundation system was based on many factors, not the least of which was the remote location of the project site and the difficulties associated with getting material, equipment and construction personnel to the project site."

Jan 1, 2017

By Kevin Baumgartner, Steven Babcock

A landfill in Phoenix, AZ reached capacity and was graded over in the 1970s. The property was subdivided into lots in 2007 to create a business park. However, the challenging site conditions caused by the underlaying landfill put into question the feasibility of typical deep foundation systems. Several different foundation systems were evaluated to support the proposed development. The considered systems were: drilled concrete shaft, driven piles, drilled micropiles and helical piles. Soil stability, landfill decomposition, method of installation, flexibility of design, anticipated material, and equipment costs were considered. A system of helical piles with concrete pile caps and grade beams was selected. To mitigate unknown obstructions, holes were drilled through the landfill debris at pile locations and then backfilled with screened granular material. The helical piles were installed through these backfilled holes and advanced to bear in competent native material below the landfill. This method allowed for minimal disturbance of the landfill materials and provided a strong and adaptable foundation. Additional advantages of helical piles on this site include minimal installation vibration, no grout or concrete in the deep foundation, and capacity verification for each pile via torque correlation. Two load tests were performed to verify the design.

Sep 8, 2021

By Bryan C. Field

The proposed construction schedule for the St. Anthony Falls I-35W Bride challenged the abilities of the design-build teams to utilize the best and most efficient methods to meet Minnesota Department of Transportation?s deadlines and design requirements to restore traffic to the Interstate 35W crossing of the Mississippi River, along with a sense of normalcy, following the bridge collapse. The project team ultimately designed and constructed two foundation systems at various substructures for bridge support. Steel H-section piles were driven to bedrock for south bridge abutment support and drilled shafts were used for the north bridge abutment and piers for the Mississippi River Bridge. Drilled shafts we also used for the abutments for the three single span bridges carrying I-35W over 2nd Street. The design-build team used high-strain dynamic pile testing with a Pile Driving Analyzer (PDA) to verify H-Pile capacities and performed drilled shaft inspection on a 24-hour basis during installation over the winter months. The drilled shaft inspection process was a vital part of the project quality control program to maintain the necessary methods for proper drilled shaft installation. Ultimately, with an efficient design, quality construction methods and operation, and a rigorous inspection and quality control plan; the I-35W Bridge was opened to traffic 3 months ahead of the already accelerated schedule.

Jan 1, 2009