Search Documents

By Scott A. Anderson, Benjamin S. Rivers, Derrick D. Dasenbrock, Silas Nichols

Unknown geotechnical conditions are a major source of risk. Unexplored places vastly outnumber the sampled and tested ones, and widely spaced boreholes with intermittent tests and samples are the norm. Sometimes site-specific planning and thought goes into locating these special, tested places, such as basing them on the geologic understanding or anticipated key locations for the structure; more often they are simply evenly distributed. We demonstrate a holographic model that allows viewers to see real data in real space, scaled or not, and to visualize where measurements are taken, what those values are indicating, and where there exists more unknown and more risk. The holographic model shows in an intuitive way, values from Standard Penetration and Cone Penetration tests, and surface geophysics. The mixed reality of this future is that a wide audience – owners, designers, project managers, contractors, and stakeholders interact together in a real space where they see and talk to each other, while at the same time are individually looking all around below or above ground, like a gopher, in a virtual one. Risk in the future will be better managed through more thoughtfully designed investigations and better communication of 3D data in a world of augmented reality. INTRODUCTION This paper explores the use of augmented reality to convey understanding of the subsurface conditions of a bridge site. This is in contrast with the current state of practice where this information is contained in a geotechnical report, and the ideas are also applicable to other structures, earthworks, and excavations. “Augmented reality” describes a situation where a 3D holographic model is displayed for users in such a way that the users experience both the model and the real environment of their setting- such as at a desk, in a meeting room, or in an open space at a project site (Figure 1). The 3D holographic model is used to directly visualize underground features, to see through the earth to the actual locations where explorations are made, samples are obtained, or measurements are taken, design values are assigned, or construction is planned. An immersive model provides the following three powerful functions for users:

Jan 1, 2019

By Rick Deschamps

"Fountain Slide is located approximately 10 mi (16 km) northeast of Lillooet, British Columbia, Canada, within the Coastal Mountain Range, and has been locally active since the 1970s. The project site is located near the base of the relic Tunnel Mountain landslide. The progressive movements have posed a significant challenge to British Columbia (BC) 99, the main north-south highway in the region. The slide began affecting the British Columbia Railway Company (BCR) tracks in the 1990s. In 2004, the Canadian National Railway Company (CN) acquired BCR and, during the next 11 years, undertook measures to stabilize the rail bed. Some of the measures undertaken include numerous track realignments, a shotcrete and soil nail wall, an anchored soldier pile-and-lagging wall, and adding a row of anchors to the wall. For many years, the measures had proved successful until mid-2014 when it was observed that the slide retrogressed uphill of the tracks. Since that time, the slide movements typically ranged between 5/32 and 0.4 in (4 and 10 mm) per day, leading to extreme distortion of the earth retention system and the need for frequent track realignment.In the spring of 2016, CN issued a request for proposals (RFP) for a designbuild solution with the expectations of: (1) a safety factor greater than 1.2, (2) considering only the currently identified retrogressive blocks that extend to about 200 ft (61 m) above the track; and (3) minimizing activities outside the current easement. It was also communicated that there was a possibility that a portion of the line may have to be abandoned if the proposed remediation was cost prohibitive.The fact that the existing slide was a small fraction of the relic slide was intimidating. The relic slide extended for approximately 1.0 mi (1.6 km) above the uppermost retrogressive block that was now affecting the rail line. Other areas of concern included:"

Jan 1, 2017

By Jahnavi Parmar, Pranav R. T Peddinti, Saloni Pandya, P. S. Prasad

Coastal cities are in desperate need of suitable land to meet the ever-increasing demand for urban infrastructure to support commercial, residential, tourism, and off-shore activities. Countries with a lengthy coastal line, such as India, possess significant areas of wide spread highly saline soils subjected to periodic seawater intrusion. One such soil stratum was encountered at the Gulf of Cambay, Bhavnagar district, Gujarat, India. Due to the high volume of river runoff, the Gulf has a positive water balance. The relative humidity ranges from 65 to 86 percent, making the climate semi-arid to sub-humid. The high salinity, mineral content, basaltic origin, and deeper water table offered the impetus to investigate applicability of various soil treatment options for such saline soils. Admixture stabilization techniques have been shown to help with problematic soil features. The Current study aims to determine effectiveness of addition of locally available lignite fly ash (10% - 30% by weight) and cement (6% - 9% by weight) to Bhavnagar saline soil in respect of strength, electrical conductivity and CBR. In this assessment, a comparison of stabilized and unstabilized saline soil mixtures is expected to highlight the need of understanding influence of treatment on instinctive performance of stabilized saline soils, as well as assist practitioners in efficacious treatment of extreme saline soils for diverse geotechnical and construction applications.

Sep 1, 2022

By Joe Welna, Lola Moussey

The Minnesota Department of Transportation (MnDOT) evaluated several concepts to minimize flooding of Trunk Highway 35W (TH35W) near downtown Minneapolis. A deep stormwater storage facility (SSF) was selected for final design. Given the constricted project footprint, open trench excavation construction methods were not feasible, and a top-down construction approach using diaphragm walls (d-walls) was utilized. The SSF is located near the edge of a glacial valley containing glacial and alluvial deposits including cobbles and boulders. Categorizing ground conditions was critical in assessing constructability of the SSF and determining project cost. Multiple phases of geotechnical investigation were conducted including geotechnical borings, geophysical surveys, and pump testing. Obstructions (including cobbles and boulders) were encountered at some of the borings conducted and therefore were anticipated to be encountered during construction. As part of development of a project risk register, it was decided by the Owner that the Contractor should assume no obstructions during d-wall construction, and obstructions encountered during construction would be paid using funds allocated in a project risk pool, which was informed by a Geotechnical Data Report (GDR) and Geotechnical Interpretive Report (GIR). The cells of the structure were successfully completed in 2022 with final completion anticipated for the fall of 2023.

Oct 31, 2023

By Brian J. Olson, Kevin Haiar

Originally constructed between 1939 and 1941 as part of Franklin D. Roosevelt’s New Deal programs, the Bonneville to Hood River 115 kV Transmission Line required an infrastructure upgrade to remain reliable and in-service. The line traverses the rugged landscape of the Columbia River Gorge on the Oregon- Washington border, featuring steep, talus slopes; uneven, rocky terrain; and a variety of environmental sensitivities. This paper details the design and construction of 27 micropile foundations for new, fire- hardening steel poles through a particularly challenging stretch of the alignment. The difficult access and environmental constraints at these sites designated them as helicopter-accessible and precluded the collection of detailed geotechnical information prior to construction. Micropiles provided a viable foundation alternative due to their portability and flexibility during construction. Detail will be provided on the extensive preliminary desktop study performed, as well as the process of developing engineering designs to successfully accommodate for variability and unknowns in complex geological conditions. With an increasing number of electric power projects traversing challenging terrain and facing similar obstacles, this project stands to provide valuable lessons learned to the industry.

Sep 8, 2021

By Teresa M. Bodas Freitas, Arianna Lupattelli, Peter J. Bourne-Webb, Diana Salciarini, Martina Zito, Donatella Sterpi

The thermomechanical response of thermally-activated (TA) piles under monotonic thermal loads is quite well understood and the remaining uncertainties relate to the effect of long-term, cyclic loading of individual TA piles and pile groups. Recent studies undertaken by the authors have provided insights into the behaviour of TA pile foundations undergoing cyclic thermal loading. Despite their simplicity, the analyses show that key aspects of the observed response of piles in sand, under cyclic thermal loading can be reproduced, providing confidence in the outcomes of the analyses. The studies examined isolated piles and pile groups, and concluded that irrecoverable thermally-induced settlement may be mitigated through the choice of an appropriate margin of safety on the pile shaft resistance under service mechanical load conditions, and the maximum thermal stress can also be readily estimated. This paper consolidates these works and provides guidance regarding the safe geotechnical and structural design of the piles, then looks towards the remaining issues around the safe provision of thermally-activated pile foundations.

May 1, 2022

By Spencer Ness, Yazen Khasawneh

Onshore wind turbines are complex and dynamic systems, undergoing variable environmental and mechanical loads. These dynamic loads are transferred through the turbine components and tower to the foundation system and, subsequently, the adjacent soil. As the size of onshore wind turbines continues to grow, intermediate-type foundations are being developed and implemented to better leverage the strength of the adjacent soils while avoiding some of the drawbacks of deep foundations. However, these foundations can be relatively sensitive to ground conditions. When considering a wind energy site that may consist of dozens of wind turbines across thousands of acres, it can be difficult to determine a design stratigraphy that is reflective of the entire site and takes conservative approaches to all potential failure modes and design checks. As intermediate foundations are inherently a soil-structure interaction problem, computer-aided numerical methods are often necessary. To highlight this condition a typical intermediate foundation with tower and turbine is assessed under eighteen different soil profiles within a finite element software and performance is compared.

Oct 7, 2024

By Packer M. L

Residual load development in driven precast piles has been widely researched in recent decades, however, cast-in-situ piles are often falsely assumed to be unaffected by this mechanism. In contrast to driven precast piles, driven cast-in-situ (DCIS) piles require adequate time prior to loading for the concrete hydration and curing processes to occur. The concrete-soil interaction is complex with several processes influencing the strains within the concrete pile after installation. DCIS piles are of particular interest given that residual loads can be developed during both the driving and casting phases. This paper present four instrumented end-bearing DCIS piles in which temperature and strains were monitored from installation, with the objective of identifying the processes contributing to the measured strains prior to testing. Strain gauges at all depths recorded a net compression and compressive strains continued to increase up to the commencement of load testing. Residual strains in the test piles were interpreted to be influenced by temperature (concrete and ambient soil and air temperature), consolidation of soils due to dissipation of excess pore water pressure, and swelling from absorption of groundwater. Several residual load interpretive methods are evaluated with the Siegel and McGillivray (2009) approach being consistent with the skin friction full mobilisation theory of the Unified Design method. The full-scale field tests presented herein provide a unique opportunity to examine DCIS pile behaviour, particularly given the lack of presently available published studies on these pile types.

May 1, 2022

By Debra F. Laefer

Jet grouting is a ground improvement technique that has become widely adopted over the past three decades, yet relatively little data has been published about performance characteristics of mixes under adverse conditions, such as the inclusion of clay lenses. This paper presents an experimental investigation on the impact of clay on the strength of jet grouting. A total of 150 grout samples were subjected to 0-10% levels of Kaolinite and Bentonite inclusion. While the Bentonite was introduced as a pre-hydrated slurry, the Kaolinite was mixed in two ways: in a pulverized condition and as large chunks. Sample strength and stiffness were measured at multiple dates within the first 28 days. With 10% clay inclusion all samples exhibited significant strength and stiffness losses. With some, substantial losses began with as little as 4% clay. Even a 1% clay inclusion tended to decrease strength and stiffness between one-quarter and one-third of the control sample. Depending upon clay type and inclusion method, results differed significantly with respect to strength and stiffness development and failure mechanism. Petrographic analysis is used to provide further insights as to apparently divergent behaviors.

Jan 1, 2009

By Neil T. Russo, Peter M. Kandaris, Jogi S. Gadok

"Assessment of subsurface data for foundation design in support of long high voltage electric transmission lines is best accomplished using a probabilistic strategy since only a small portion of structure locations are typically sampled. Probabilistic approaches provide a tool to evaluate site uncertainty in a systematic and rational manner. This paper provides a case history of a risk-based design approach for a recently completed 191-mile long 69/161/345kV steel monopole transmission line traversing Central Iowa. The project owner made available limited subsurface information at project initiation, requiring the design team to obtain additional data within a constrained budget for 1067 large diameter, laterally-loaded deep drilled shaft reinforced concrete piers. The team commissioned a geologic desktop study to reduce uncertainty in subsurface evaluations and aid in selecting additional sample sites. In total, investigation programs tested approximately 15 percent of structure sites. The paper details the probabilistic approach used to estimate foundation geotechnical design parameters, with information from the various studies categorizing strata both laterally and with depth. Low-bound parameters were estimated via a statistical approach at a predetermined reliability level. Significant savings resulted from this approach when compared to conservative deterministic processes. Project QA/QC logged subsurface soil conditions during foundation excavation, then compared as-found conditions to the conditions assumed for design. The team redesigned foundations if either a non-conservative variance in soil conditions was observed or if bedrock elevation differed significantly from design assumptions. As a result, only 22 out of 1067 foundations required modification during construction (2% variance from initial design) with negligible impact on the construction budget and schedule.INTRODUCTIONFoundation design for long high voltage transmission lines presents a unique challenge in that the assessment of subsurface conditions typically requires substantial data that may or may not be obtainable. Investigations are usually performed well in advance of construction, often with limited access to structure sites and typically in remote areas. Probability and risk-based investigation and design strategies offer an opportunity to systematically estimate subsurface profiles and geotechnical design properties with limited data. Risk can be further reduced with dedicated field inspection of foundation construction along with good field and design team communication during construction. This paper presents a case history of probabilistic methods used for the investigation and design of electric transmission line foundations."

Jan 1, 2017

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid Deep Mixing (DM) shoring system was recently constructed for a high-rise development in downtown Vancouver, British Columbia, Canada for the temporary support of a five-level basement excavation. The site is bounded by an existing bridge off-ramp structure along its longest side and by city streets on the other two sides, which formed a truncated triangle in plan. A conventional secant pile wall was installed along the longest side, about 380 ft (116 m) in length, of the site. Hybrid shoring walls (HSW) 1 and 2 were installed along two shorter sides with each being 235 to 246 ft (72 to 75 m) long. HSW 3 completed the excavation support system along the shortest side with a length of about 55 ft (17 m). Cutter soil mixing (CSM) was proposed by the excavation and shoring design-build team in lieu of conventional secant piling. CSM was the preferred method to construct the infill panels between soldier piles because of the speed at which the shoring system could be constructed in the variable fill, peat, wood waste and overburden. Design ConsiderationsTo minimize the impact on buried utilities along the outside perimeter of the excavation, the temporary shoring was designed to limit the lateral displacements to less than 0.8 in (20 mm). Factors taken into consideration for shoring design included the lateral earth pressures from the fill and native soils, groundwater pressures, temporary construction loads (e.g., crane or heavy plant/equipment), and permanent structural requirements. The subsurface conditions at this site typically consisted of fill (cohesive and granular), overlying peat and/or wood waste, overlying clayey silt to sandy silt, overlying weathered to dense to very dense clayey silt till to sandy silt till with silt layers. Localized, perched groundwater was observed within the fill, peat, wood waste and sandy silt layers above the dense till."

Jan 1, 2017

By Kenton W. Braun

Concourse B at the Anchorage, Alaska International Airport is currently being renovated while retaining the original building structure and foundations. Part of the renovation includes the installation of a new, permanent baggage tunnel system beneath the existing building. Installation of this cast in place concrete tunnel, beneath the existing structure, required installation of a steel retaining wall to support footing loads above the base of the excavation. Construction of this retaining wall presented challenging and unconventional design and construction methods. Detailed discussions of the design and construction techniques utilized for this project are outlined.

Jan 1, 2008

By J. Erik Loehr, Minh Uong, Andrew Z. Boeckmann, Sarah G. Myers

"The University of Missouri performed a lateral load test program involving 32 drilled shaft load tests for the Missouri Department of Transportation (MoDOT). Tests were performed at two MoDOT geotechnical research sites, and all shafts were founded in shale. Shafts were instrumented to measure the displacement of the shaft head, and the structural response of each shaft was interpreted from strain gage data and from ShapeAccelArray (SAA) data. The SAA is a chain of rigid segments with sensors that use MEMS (microelectromechanical systems) technology to measure the tilt of each segment/joint. The measuring principle of the SAA is therefore similar to that of an inclinometer. The SAA device was placed in a casing installed in the center of each test shaft to provide a continuous record of deflection along the length of the shaft throughout each test.Bending moment profiles were calculated from strain gage data and from SAA data. Interpretation of bending moments from measurements of strain (via strain gages) and displacement (via SAA) is a nontrivial exercise, primarily because the bending stiffness, EI, is nonlinear and greatly influenced by concrete cracking, which is difficult to predict. The procedure used for this work predicted values of bending stiffness along the length of the shaft as a function of the bending curvature, which was interpreted from the SAA data. Values for bending stiffness as a function of curvature were computed using Ensoft LPile v2012. Bending moment profiles from SAA data were typically similar to those from strain gage data. The SAA bending moment profiles were often “noisier” than the strain gage bending moment profiles, but the SAA bending moment profiles had more data points since the SAA chain was continuous from the top to the bottom of each shaft."

Jan 1, 2017

By Ronnie Melker, Joel Webster, Daniel Belardo, Thomas Hyatt

Quality assurance of drilled shafts is highly dependent upon the construction practices used during the excavation and concrete placement process. When performed under slurry, challenges are presented in maintaining borehole stability and placing a uniform and continuous concrete column. An integral part of the construction operation is to evaluate the as-built integrity to verify the drilled shaft is capable of safely transferring the required loads to the subsurface. One such case is exemplified by a project involving the expansion of an existing public transit rail line. The expansion required the construction of a new bridge bent supported by seven 5-ft diameter drilled shafts of various lengths. The specifications for the project required both Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) for drilled shaft integrity evaluation. Both of these post-construction non-destructive tests (NDT) are designed to detect anomalies or the presence of regions with reduced concrete quality. However, the implementation and methodologies of performing each of these NDT methods are significantly different. Cross-Hole Sonic Logging uses ultrasonic signals emitted from a transmitter in one access tube to a receiver in another access tube. Thermal Integrity Profiling measures elevated concrete temperatures during the curing process using embedded thermal wires. Both test methods require different access details and therefore have different costs associated to the contractor or owner to perform. This paper provides a detailed comparison of these NDT methods as performed on these seven drilled shafts. The associated financial and time costs to perform each method are compared and the results are discussed in detail. INTRODUCTION Drilled shafts are a fundamental deep foundation element that can be designed to resist large bending moments as well as to transfer large compressive axial loads through weaker upper soils to competent soils or rock below. Often times when the upper soils are very soft, lateral support by casing or slurry, or a combination of both, may be used to hold back the softer soils from collapsing into the hole before concrete has been placed. Due to the blind nature of drilled shaft construction and the qualities issues that may arise during the placement process, it is essential for design engineers to specify non-destructive testing (NDT) to assess the quality of the as-built drilled shaft. CSL and TIP testing are two NDT methods designed to detect areas of lower quality concrete or soil inclusions throughout the length of the drilled shaft and determine its overall quality. Each method uses different technologies and methods to achieve the results required to determine the as-built condition of the drilled shaft.

Jan 1, 2019

By Martin B. Hudson, Andrew K. Cho, Rolff B. Knobel, Les R. Chernauskas, Jonathan L. Ernst

ABSTRACT The Bruce Museum, located in Greenwich, Connecticut, is home to an extensive display of art and natural history exhibitions. A large addition was designed to be constructed adjacent to the museum requiring new spread footings to be installed up to 16.5 feet below the existing foundations. The soil conditions at the site consist of highly variable sand and gravel overlying weathered rock and sound bedrock. The Contract Documents called for traditional foundation underpinning. Traditional underpinning techniques, however, presented two major challenges on this Project; (1) deep underpinning pits would be required involving multiple levels and staging with tieback support and (2) the highly variable soil and bedrock composition and elevations presented uncertainty in the design and construction of the pits. In lieu of traditional underpinning, Geosciences Testing and Research, Inc. (GTR) proposed an “active” soil nail underpinning system. A major reason that the soil nail underpinning option was feasible, related to the fact that the soil nails and facing could be installed slightly in front of the existing footings rather than directly underneath the existing footings. The soil nail wall design involved one to four rows of soil nails with nail positions and wall depth able to be adjusted “on the fly” as excavation progressed depending on the field conditions encountered. To create the “active system,” the soil nails were pre-loaded to mitigate wall deformations that would be associated with a standard passive soil nail wall design. To evaluate the performance of the active soil nail wall and confirm design assumptions, an extensive automated monitoring, on-site testing and inspection program was proposed and executed by GTR to monitor deformations of the wall and the museum in real-time, evaluate and confirm bedrock and soil bond stresses and ensure that each soil nail was pre-loaded and locked off. Careful analysis, planning, and use of the observational method illustrates the importance of collaboration between design and construction personnel and applying engineering judgement throughout construction. The use of the observational method includes the potential for modifying design based on conditions observed. This paper presents a unique case study of the “active” soil nail underpinning system to support and protect sensitive structures, close collaboration between design and construction facilitated by real-time deformation monitoring, and its successful application as a safe and cost-effective alternative to traditional underpinning.

Oct 1, 2022

By Maurizio Siepi, Bruno Vingiani, Claudio Asioli

"The article describes an emergency rehabilitation intervention executed at Buyo Dam, in Ivory Coast, to intercept a significant water seepage occurring through the foundation of this zoned earthfill retaining structure constructed in the late Seventies. To solve the problem, a 800 mm thick, 400 m long impervious cut-off wall (COW) was constructed on the right side of the embankment, operating from the dam crest and with the reservoir almost at its maximum level. The use of an innovative pre-mixed self-hardening grout, with a target hydraulic conductivity coefficient (k) lower than 10-9 m/s, was considered the only way to match the tight working schedule and the strict requirements for the filling material of the COW.Presentation of the Hydroelectric Scheme of BuyoThe hydroelectric scheme of Buyo, located at 6°14’28” N 7°20’45 W on the Sassandra River, in Ivory Coast (Figure 1), was built in the late Seventies for agriculture and power generation. With a reservoir of 8.3 billion m3 and an installed power capacity of 165 MW, enough to supply electricity to 111,000 homes, it represents an installation of great significance for this West African country."

Jan 1, 2016

By Mohamad H. Hussein

A minipile system was employed in underpinning a historical structure in Florida. The existing structure is founded on shallow foundations. Subsurface conditions at the project site consist of deep organic deposits interbedded with loose sand and silty sand. A minipile foundation system was deemed the most appropriate underpinning corrective measure for the already badly cracked structure. A total of 68 minipiles, 3.5 inch OD and 0.25 inch wall thickness closed-ended concrete-filled steel pipes, were installed to depths varying from 55 to 175 feet. Installation was accomplished with a pile driving hammer having a rated energy of 1 kip-ft. Highest required pile design load was 15 kips. Conventional static and wave equation analyses were performed to establish preliminary pile lengths, to assess pile drivability and establish driving resistance criteria. Dynamic pile testing using the Pile Driving Analyzer was conducted on six of the production piles. This paper describes geotechnical design considerations, installation procedures, and dynamic field monitoring. This case represents unique applications of pile dynamic testing and such slender, very long minipiles in compressible soils.

Jan 1, 1993

"The development of non-destructive testing (NDT) methods for deep foundations occurred in several parts of the world, gradually coming together into the present state of the art. The compilation of this brief NDT history is the best effort of several knowledgeable members of the Deep Foundations Institute (DFI) Drilled Shaft Committee, coupled with the recollections of several historically important contributors to the science. It is not intended to be exhaustive, but rather concentrates on the origins of the methods in common use and on which this manual focuses.Modern NDT methods, and the spread of knowledge about them, have expanded through application to real foundations projects by the original researchers, sometimes inspired by their own curiosity, sometimes to respond to the cost and time limitations imposed by static testing, and sometimes to address the questions raised on research projects funded by large government agencies such as the Federal Highway Administration (FHWA) in the USA, and various European transportation agencies. Initial attempts were primitive by today’s standards, and equipment limitations often restricted successful application to relatively simple cases. As electronics improved and confidence in them increased, the early researchers began commercial promotion of their methods, published their findings in professional journals, and shared experiences at conferences held by such groups as the DFI, the International Association of Foundation Drilling (ADSC), the International Conferences on the Application of Stress-Wave Theory to Piles and other venues such as ASCE and Transportation Research Board (TRB) conferences.NDT methods were developed to fill a need to assess the quality assurance of deep foundation elements. New pile types and higher design loads prompted engineers to verify the safety of their foundations via additional testing during construction. Static load testing was the traditional method to assess performance, and this method has been used for centuries and perhaps even millennia.Relatively recent alternatives to static load testing for determining the capacity of drilled shafts include the bottom load test method. This method uses a jack embedded in the lower portion of the pile (bottom load test) and was first reported to be used from Canada in the early 1970’s (Gibson& Devenny 1973). The concept immediately caught on in Israel, where it was used as a quality control measure for small-diameter piles drilled in rock (then a new technology). The method was later patented in the US by Jorj Osterberg, and offered as a commercially available service in thelate 1980s (Osterberg, 1989)"

Jan 1, 2004

By D. Cantali

This paper will be presented in two parts. The first part will present the latest advancements in pile installation techniques using state-of-the-art press-in piling technology by Giken. By pressing in sheet piles and large modulus contiguous steel tube pile walls – as opposed to the more traditional installation methods using percussive hammers or vibrators – retaining structures can be constructed effectively noise and vibration free. For over water and coastal projects with limited access, this provides significant environmental benefits in the form of minimising the construction foot print and the impact to surrounding communities and the marine natural habitat. Typical noise and vibration data will also be presented. The second part of this paper will review the current manufacturing techniques for sheet piles and introduce innovative new materials used in the current piling market for embedded sheet pile walls. Materials include long service life non – ferrous materials such as new age plastics and fibre reinforced polymer piles. Their excellent long term performance and durability make them an effective solution in the marine environment. For steel piles, a number of steel grades with reduced corrosion characteristics will also be discussed including a newly developed steel to combat corrossion in the low water zone, an area often exhibiting the highest moments in a retaining wall. A number of project case studies will also be presented to reinforce their relevance in today’s changing construction landscape.

Nov 1, 2022

By Juan M. Pestana-Nascimento, Robert G. Bea, Hamed Hamedifar, Emery M. Roe

The current State-of-the-Practice is grounded heavily on deterministic characterization and assessment of the performance of civil engineering infrastructure. In particular, flood defense systems, such as levees, have been evaluated within the context of the Factor-of-Safety where the computed capacity of the system is compared with the code specified demand forces. Uncertainties associated with the capacity and demand forces render deterministic modeling incomplete. In particular, two structures with the same Factor of Safety can have vastly different probabilities of failure. While efforts have been made to assess levee vulnerability, results from traditional engineering approaches omit important factors because they do not account for uncertainties included in analytical modeling, and natural variabilities, or human and organization factors. This paper utilizes risk assessment methods to advance methods for quantifying the contribution of uncertainties to engineering analyses, and thereby provide additional information to help assess sustainability of geotechnically engineered systems. The probability of failure of a geotechnically engineered system is directly impacted by how well the system is understood, and how uncertainties are incorporated in development of understanding of the system. This paper presents methods to evaluate two types of uncertainties for three potential failure modes of flood protection levees: underseepage, slope (or levee) instability, and overtopping/erosion. These analyses account for two types of uncertainty: 1) Type I – inherent uncertainty, 2) Type II – analytical modeling uncertainty. Human and organizational task performance and information development and utilization uncertainties are not included in these analyses. This paper focuses on the behavior of the flood protection levee system for Sherman Island, a western island in California’s Delta. Sherman Island is of critical importance to California because of the very important infrastructure systems that pass under, on, over, and adjacent to Sherman Island, including: natural gas pipelines, regional and interregional electricity transmission lines and telecommunication facilities, two deepwater shipping channels; and State Highway 160, a link between major transportation expressways. The work evaluates current (year 2010) and future conditions (year 2100) and incorporates variations in capacity and demand arising from projected human response activities and global climate change.

Jan 1, 2017