Search Documents

By Shamsher Prakash

Estimation of vertical load carrying capacity of a single vertical pile under earthquake loading is an important task of a design engineer. Lateral vibration of vertical pile is highly influenced by the magnitude of vertical load. Several load reversal, during earthquake loading introduce gap between pile soil interface which reduces its load carrying capacity and increases lateral motion. This paper presents a simple time domain numerical scheme to estimate the lateral pile response, considering the loss of contact of pile at pile soil interface, during impact and earthquake loading. The motion of the pile is limited in the vertical plane. Time domain has been discretised into small intervals. The non linearity of soil properties has been taken into account by discretised Winklers model with Wolfes frequency independent mass spring dash pot coefficient for geometric damping. Suitable software has been developed which keeps track of the load reversal point of each elements.

Jan 1, 1996

By Andrzej Tejchman

A method of improvement of a subsoil under bored pile base by injection is presented. The method employs a special chamber attached to the reinforcement at the bottom of the drilled borehole. The chamber is made of semi-permeable textile bag. The injection entered under high pressure into the bag, causes prestressing of subsoil under the pile base. The results of load tests of piles improved in this manner have shown a substantial increase of their capacity together with simultaneous reduction of settlements. This technology has been implemented for four constructions such as trestle bridges in Gdynia and Warszawa and the bridges in Szczecin and Gdansk. The injection effects are shown based on the load test results.

Jan 1, 2002

By Shenbaga R. Kaniraj

The pile loading tests are generally conducted to assess the safe load on piles in compression. In the Indian practice, the safe load is determined using the pile loading test data and the two criteria specified in the Indian Standard Code, IS.2911 (Part 4) -1985. For this, the test pile should have undergone a minimum displacement equal to 10% of the pile diameter. Often, the piles are not subjected loads that are sufficient to cause a displacement of this magnitude. If the settlement is at least 12 mm, then the safe load is determined based only on the first criterion. But, if the settlement is less than 12 mm, the safe load cannot be determined using the IS Code criteria. The paper presents two procedures called hyperbolic and generalized hyperbolic methods to estimate the safe load using the IS Code criteria even when the loading test data is insufficient. The data from two initial tests have been analyzed. The predicted safe loads have been compared with the actual safe loads.

Jan 1, 1996

By Chen Zhiquan

Author has exhaustively researched into soft ground through construction of a large open caisson on soft ground (muck) which weighs more than 4, 000 tons. To avoid any contingency during construction, we precompressed muck stratum with a sand cushion and consolidated it with sand piles before construction of the caisson. We made borehole surveyings and soil tests many times before and after ground treatment. Following the tracks of changes of the caisson at all stages of precasting, we surveyed a large number of data. On the basis of analysis of the data we changed the original construction plan of precasting in four stages and sinking in three stages into that of precasting in three stages and sinking in one stage. Through the practice of the whole caisson construction the author has advanced new theory of kinematic law for soil particles and the change's law for strength of muck during precompression of sand cushion and consolidation of sand piles.

Jan 1, 1991

By Manish Kumar

One of the recent advances in the field of testing of concrete piles is the Non-Destructive testing (NDT) of piles. This paper deals with a specific project where this technique was employed along with an extensive program of conventional testing methods to cross check the results. Conventional testing of the Bored, cast-in-situ piles involved taking full length concrete cores from piles to check physical properties such as core recovery, RQD, crushing strength and density of concrete. Additionally, a number of questionable piles were exposed and inspected and actual load tests were performed on selected piles. Concrete pour cards were used to compare actual Vs theoretical consumption of concrete. A direct comparison of the conclusions drawn from both these testing methods provided an excellent opportunity to better understand the intricacies of NDT technique. The study undertaken clearly indicated a need for developing clear guidelines and specifications for the use of this method of non-destructive testing of piles before the .method can be accepted as a useful quality control tool at the construction sites.

Jan 1, 1996

By Wang Lushuang

This thesis is devoted to the research of the interaction between pile and foundation soil by boundary element method (BEM for short). The interaction is simulated by the interaction between two different elastic mediums. The foundation soil is simulated by the two-dimensional elastic half-plane, and the pile by the two-dimensional elastic finite plane. Therefore, the calculating models made by the paper's author would come more closed to the actual conditions. The elastic behaviour of the interaction between pile and soil, and the whole course of pile ultimate load are analysed in the thesis, and the relevant applied computer programs "BEME", "BEMPA" are designed by the paper's author. The bearing power of single pile can be worked out by the program "BEMPA", it has compared with staic loading tests of pile, and the results are in conformity to actual conditions. So it can be drawn that the BEM for studying on interaction between pile and foundation soil made in the thesis is more simple, more precise and more practical in actual project.

Jan 1, 1991

By Subrata Ray

A large no of power stations are being set up in Chandrapur area having coal deposits. Several industries are also coning up in this area. The subsurface is geologically formed under Gondwana system and consists of shale strata at depths ranging from 8 to 12 m. The stress deformation characteristics of shale exhibits wide variation because of it's geological origin. In view of this, a study was conducted on bored cast in-situ piles installed for a Switch yard project to evaluate load settlement characteristics of three test piles to understand the probable engineering behaviour of the material at the tip and the sides. An approach is developed to simulate the load settlement behaviour as observed in the field, theoretically. This is based on the concept of load transfer. The fit is obtained by varying the parameters, thus may be considered as iterative in nature. The theoretical curves closely matched the observed curves. The results of this study are presented in this paper.

Jan 1, 1996

By Naim Noori Samie

Lateral force rsistance of piles is analytically investigated by dividing the pile length to 3 segments. The first segment (Zone I) models the load eccentricity with respect to the soil and the pile-deck connection, using a third degree differential equation representing the shear variation along the pile. The soil is assumed to be uniform, homogeneous with an elastic-perfectly plastic behavior. The Top soil layer (Zone II) is assumed to be stressed beyond the elastic limit. A simple 4th degree differential equation represents this zone. The soil resistance is assumed to vary linearly with depth (or surcharge). The pile deformation and soil behavior determines the plastic zone length. In zone III the soil is assumed to behave elastically, hence its resistance is proportional to its deformation. A linear 4th degree differential equation is employed in this zone. The compatibility conditions are satisfied on each boundary. Maximum allowable moment and shear are investigated throughout the pile as the basic limiting criteria on lateral force capacity. In this paper the soil coefficients are taken from a proposal by ref(3), and the results are compared with the soil response as determined by the P-Y method as recommended by ref(2).

Jan 1, 1996

By John Y. L Chen

This paper presents full-scale instrumented pile static compressive and tensile load tests to be conducted in the area of Pearl Harbor, Hawaii. Thousands of piles have been installed to support the existing piers and wharves in the Pearl Harbor area. Due to the absence of bedrock within practical depths, most of the piles use combined friction and end bearing. A new 925 feet (282 meters) long and 50 feet (12 meters) wide reinforced concrete wharf supported on pile foundation is planned. This paper will present results of soil investigation, laboratory testing, dynamic load tests during indictor pile driving and static pile load tests. The subsurface conditions consist of soft harbor sediment, young alluvium deposit, volcanic tuff rock formation and stiff old alluvium deposit. The load test piles consist of 20-inch (508 mm) square and 24-inch (610 mm) octagonal pre-stressed, pre-cast concrete pile and instrumented with embedded strain gauges. The length of the piles ranges from about 50 to 125 feet (15 to 38 meters). The test pile program consists of probing, driving indictor piles, dynamic load tests during indictor pile driving and static load tests. The standard loading procedure method was used during static pile load tests.

Jan 1, 2002

By Dinesh R. Katti

Caissons which are locally known as well foundations, which may very in diameter from 30 m to more than 30 m and in majority of the cases having depth to diameter ratio between 1 to 1.5, are normally used to support piers of long span bridges or tall structures, which transmit high magnitude of axial load, horizontal thrust and moment. On the basis of depth to diameter ratio the foundation system appears to fall in the category of shallow foundations but due to deep excavation, it is observed that part of the moment acting on the caisson is shared by due the sides due to development of passive resistance. The problem is statically indeterminate and three dimensional in nature. To ascertain the various parameters needed for design, such as moment shared by base and sides, horizontal and vertical displacement and tilt, and base and side contact pressure diagrams need to be obtained from nondimensional relations of parameters with respect to D/B ratio derived from large scale model studies conducted by Katti etal at IIT, Bombay under MOT Project between 1976 and 1988 and later on at UNEECS. On the basis of above data on attempt is made to put forward guide lines for selection of parameters for design of caisson foundations / well for following cases for opening us some discussion. The cases are cohesive soil at the side and cohesive soil, or sand or soft rock or hard rock at the base.

Jan 1, 1996

By Emad Farouz

This paper compares the predicted axial capacity of driven Pre-cast Pre-stressed Concrete (PPC) piles for the Lake Gaston Water Treatment Plant (LGWTP) using several design methodologies versus the axial capacity measured from dynamic and static load testing. The LGWTP site is located in Chesapeake, Virginia and is part of the Great Dismal Swamp. The subsurface investigation included soil borings, in-situ dilatometer (DMT) tests, and in-situ piezocone (CPTu) tests. The axial capacity predictions of the PPC piles were performed using the computer programs DRIVEN and FB-DEEP which are based on SPT N-values. Additionally, an empirical method proposed by Martin, et al. (1987) based on local experience with PPC pile design in the Yorktown formation in the Tidewater area of Virginia was also evaluated. Finally, the ?Laboratoire Central des Ponts et Chausées (LCPC)? method developed by Bustamante and Gianeselli (1982) based on CPT measurements was also used to develop the axial pile capacity of the piles. This paper shows that the FB-DEEP computer program and the LCPC method provided a reasonably good prediction of the pile axial capacity measured from PDA, CAPWAP, and Static Load Tests in comparison with the other design methods used. The soils in this area develop significant setup over time and it was found that FB-DEEP and the LCPC method are capable of incorporating this setup in the prediction of the long-term axial capacity of driven piles in this area.

Jan 1, 2007

By Kyle L. Murrell

Along the southeast United States coast, clayey silt and silty clay marine formations may cause pile installation and integrity problems. More specifically, excess pore pressures which develop in these soils during driving can cause high displacement piles to rebound or ?bounce?. Bounce is defined as a large (¾-in. to more than 1-in.) downward pile displacement during the hammer blow with little to no net displacement at the end of the blow. Pile bounce can generate damaging tension stresses and result in inefficient pile installation. A case history is presented where pile bounce was observed during the installation of 20-in. square ?high displacement? prestressed concrete piles which support a new ferry terminal in coastal North Carolina. High-strain dynamic pile testing was performed during test pile installation to evaluate driving stresses, pile capacities, and hammer performance. During and after installation of numerous production piles, circumferential cracking was observed on some of the piles. Additional high-strain dynamic pile testing was performed on two piles installed with a hammer having a heavier ram than the initial hammer. The new driving system generated lower tension stresses and installed the 20-in. piles more efficiently. Low-strain integrity testing was performed on the piles to qualitatively assess the cracks and locate any unidentified cracks. The low-strain testing was performed on piles installed at least a week prior to testing and on piles installed immediately prior to testing. When low-strain testing was performed immediately after pile installation before dissipation of excess pore pressures, pile integrity could be evaluated to depths of at least 12 pile diameters deeper than when performed weeks after installation.

Jan 1, 2008

By F. M. Abdrabbo

Flight auger bored piles are formed by screwing a continuous flight auger into the ground, and pumping cement/sand grout or concrete down the hollow stem of the auger as its withdrawn. The auger is driven at the top by hydraulic or electrical motor and is guided by a vertical crane leader. Loading tests on concrete piles are described. The stability plot method is used to drive the shaft friction and the end bearing load components of the pile capacity. This paper outlines features of crucial construction factors that affect the geotechnical capacity of this type of piles. These factors include, vertical speed of auger during boring, grout factor, grout pressure, number of reborings, type of material, and slump of concrete used to form the piles. Two of these factors are highlighted in this paper. It was found that, shaft resistance is independent of grout factor, whilst point resistance increases as grout factor increases. Nevertheless the engineer should decide the safe pile load associated with the most economical grout factor. High vertical speed of auger during boring of piles may cause disaster for the adjacent buildings, due to soil decompression.

Jan 1, 1993

By Haijian Fan

Currently, deep foundation designs for the service limit state are deterministic in nature. The settlements and lateral deflections of deep foundations are calculated by means of numerical techniques whereby the foundation-soil interactions are characterized by discrete load transfer curves such as t-z or p-y curves. The noted deficiency of the deterministic approach is that the uncertainties arising from various sources, such as soil properties and model errors are not considered. To address this deficiency, a performance-based reliability design methodology is developed using Monte Carlo statistical methods. The performance based design criteria are defined in terms of the specified allowable displacement. The input to the numerical solution techniques, including the soil strength parameters, unit weight of the soil are relevant to the generation of the load transfer curves are treated as random field. The well established random field generator algorithm, local averaging subdivision, is used to generate random samples of input, where the mean values, variances, the probability distribution, and correlation structures are required statistical parameters for these random variables. The objective of the performance based reliability design is to determine the optimized foundation dimensions so that the probability of failure is less than the target probability of failure. The probability of failure by the Monte Carlo approach is simply the ratio of the number of unsatisfactory performance to the sample size. A numerical example for laterally loaded drilled shaft is given to illustrate the application of the methodology. The incorporation of the correlation length is shown to be critical for properly accounting for the site soil spatial variability.

Jan 1, 2017

By Masaki Kitazume

Five papers were presented orally to the topics of Jet Grouting and Deep Mixing. The session was started with a brief introduction by the moderators. Following the oral presentation, floor discussions were directed by the moderators. A brief introduction of each of the oral presentations is provided before each discussion.

Feb 10, 2003

By Helen Ahnberg

The scope of the present paper is limited to report the experimental evidence and not for describing the analytical assumptions. However, the idea behind the experimental program is that the deterioration may be caused by the leaching of Ca from the treated soil to surrounding soil or water driven by the difference in the Ca ion concentration. As a consequence of Ca leaching, it may be natural to expect the expansion of micro void space within the treated soil. In a saturated condition, the water inflow into the treated soil may accompany the leaching phenomenon. We measured the water content within the treated soil. But there is not much difference in water content within the soil.

Feb 10, 2003

"Full time inspection of drilled shafts by qualified personnel is a necessary part of construction. Detailed inspection procedures for routine inspection are provided in the Drilled Shaft Inspector’s Manual, published jointly by the DFI and ADSC: the International Association of Drilled Shaft Contractors.The use of NDT methods or other observation methods, such as probes, video camera inspection, remote shaft wall inspection devices or various calipers are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT and other "remote" or indirect observation methods are valuable alternatives to direct entry of personnel into drilled shaft excavations. They should be considered whenever appropriate to reduce the risks of direct entry of personnel into drilled shaft excavations.As described in the Drilled Shaft Inspector’s Manual, observations made during construction are essential for quality construction of drilled shafts. The shaft depth, diameter, plumbness, bottom conditions, reinforcement, concrete continuity, and bearing conditions are most easily checked during construction. Some of these observation methods include excavation around the shaft for relatively shallow inspection, down-hole inspection for end bearing conditions or rock sockets, and video camera devices for remote inspection. In rare circumstances, a drilled shaft can be extracted for inspection. Before concrete placement, the bottom of the shaft can also be probed by drilling or coring to determine if there are voids or soft zones in the material at the base of the shaft.The Drilled Shaft Inspector’s Manual focuses on traditional "topside" inspection for routine drilled shaft construction."

Jan 1, 2004

By William F. Starke

"The Ontario College of Art & Design (OCAD) located in Toronto, Ontario, found itself in dire need of space due to increased enrollment, leading them to embark on a major expansion and redevelopment on campus. The expansion entailed an additional 115,000 sq.ft. (10,700 m2) and a new major structure was required, as well as extensive redevelopment of existing buildings. The new Sharp Centre for Design was designed by acclaimed British Architect Will Alsop, of Alsop Architects, in a joint venture with Toronto-based Robbie/Young + Wright Architects. The OCAD campus is cramped for space and the design selected was a structure built over top of existing structures. The building has been described as resembling a “shoebox in the sky”, supported on raked columns transmitting high lateral forces as well as compression load to the foundations. There are 12 such supports, each supported by an individual caisson. In addition, the project entailed installation of other caissons in the courtyard area with the construction work accomplished under very confined conditions among the existing structures. The remarkable design for the new Ontario College of Arts will surely make it another of Toronto’s architectural landmarks. Several things make this project stand out as a unique deep foundations project.First is the architectural design. Words cannot do it justice: the picture is the only effective way to start to describe it. This is a big two-story box, built over the top of a fragile existing building. The underside of the box is 86 ft (26m) above street level. Students remained still inside the old building while construction was going on around and above them. There were serious concerns about vibration – not only its effects on the academic life; but more significantly, upon the stability and safety of the old building, which rests somewhat shakily on shallow spread footings.Steel stilts that look like toothpicks when scaled against the new and existing structures support the box. The stilts are much sturdier than they appear from the pictures, but it is easy to visualize the complexity of the loads they transfer to the foundations below."

Jan 1, 2004

By Brian Wilson, John Scholte, Megan Atkinson

"In November 2004, the residents of the City of Nanaimo, B.C., Canada voted to approve a new conference centre as the centrepiece of a proposed revitalization project for the city’s historic downtown core. The proposal goal was to replace a cluster of derelict buildings with a dynamic and modern complex that would connect existing city facilities to a new conference facility, the Vancouver Island Conference Centre (VICC). The conference centre is expected to create 150 full-time jobs, attract visitors/ delegates from across North America and generate new economic opportunities for local businesses.However, the proposed site posed a number of geotechnical and geoenvironmental challenges. As is often the case with coastal cities, historic growth of the Nanaimo downtown and harbour area was achieved through reclamation of former waterfront areas and inlets. These areas were often infilled with random fills and even wastes, leaving a legacy of variable density heterogeneous fills contaminated with a variety of pollutants. Preliminary assessment of the site indicated a high likelihood of a requirement for deep foundations, a high risk of liquefaction in the event of an earthquake and the presence of both soil and groundwater contamination. Construction would be further complicated by the requirement for two levels of basement parking and the proximity of adjacent buildings and major roadways to the work area.With a limited budget (fixed by the referendum) and timeframe, the city needed a cost-effective solution to proceed with construction. A number of options were considered, but an innovative design using leading-edge Cutter Soil Mixer (CSM) technology best met the geotechnical and budgetary requirements of the site. The CSM approach also addressed the environmental concerns of contaminated soils and groundwater. Golder Associates Innovative Applications (GAIA) Inc., in association with the designers of their parent company Golder Associates Ltd. (Golder), proposed the CSM technology — at the time the first North American application."

Jan 1, 2008

By Patrick van der Schaaf

"During 2016, foundation piling works were completed to allow for the construction of a production and storage/handling terminal in Rotterdam. It is there that steel foundations will be produced for offshore wind farms and the oil and gas industry. Several Dutch contracting companies were involved in constructing: foundations for an assembly hall, a barge quay and a deep-sea quay wall. For the hall foundations, cast in situ concrete vibro piles were created. Open ended steel casing piles were also installed due to very high cone resistances which made it impossible to perform cast in situ piles in certain areas. The quay wall was constructed with open ended steel casing piles in combination with sheet piles. A deep-sea quay wall was also constructed to provide enough storage area for the offshore mono piles. This project was unique and challenging due to the use of different foundation technologies in challenging circumstances and soil conditions. This paper will give an insight into the Dutch use of varying foundation piling techniques for deep-sea quay wall constructions. It can be concluded that even experienced local contractors can be surprised by variations in soil conditions. It will also show how the contractors adapted to the difficult circumstances.PROJECT OUTLINEThe project consisted of a barge quay near the assembly hall with a length of 500 metres, width of 42 metres and a height of 35 metres, and a deep-sea quay wall 480 metres in length. This paper concentrates on the foundation works for the construction of the deep-sea quay wall. The construction of the deep-sea quay wall consisted of a combination of open ended steel casing piles with a diameter of Ø 1420 mm and a wall thickness varying between 21 and 23 mm. The lengths of the steel casing piles varied between 32 and 37 metres. Between the steel casing piles triple PU 28 sheet piles were installed with lengths varying between 26 and 29 metres. In the Netherlands, a combination of open ended steel piles and sheet piles is known as a “combi wall”. For the deep-sea quay wall a steel combi wall was shored with steel H- section profiles that were driven in a raked position whilst being injected with grout, so called MV-piles. The MV piles for this project consisted of steel HEB 600 sections with lengths from 52 up to 59 metres and were installed with angles varying between 42.5 and 47.5 degrees. For a detailed overview regarding the project specifications reference is made to table 1 which is presented below."

Jan 1, 1900