Search Documents

THIS article describes the origin and details of a hydraulically operated switch to control the operation of an automatic underground pumping system. This system was installed in December, 1939, on the 2,350-foot level at No. 5 shaft of the Buffalo Ankerite mine. The pumping unit consists of an 8-stage centrifugal pump direct-connected to a 150 h .p., 2,200 volt motor. Pumping capacity is 200 gallons per minute under a 1,315-foot head and with a flooded suction. The control consists of a 200 amp., 2,200 volt oil-immersed starter with thermal overload protection, thermal protection on the pump, and a flow switch that is bypassed for 30 seconds after the pump starts. The 30-second time lag is operated by a relay mounted on the panel. There is a swing check valve in the discharge line of the pump which originally operated the flow switch by means of a connected outside lever which closed the switch as the check valve opened.

Jan 1, 1945

By A. R. Turner

AERIAL survey methods have made enormous technical advances and gained new recognition since World War II. Before enlarging on this statement and reviewing some of the uses of aerial survey in industrial development it is important to de-fine what is meant by "aerial survey". The subject will be discussed in the broadest sense and references will be made to the four sections that compose the overall field of surveying operations from the air. These are: 1. Aerial photography and photo-graphic mapping. 2. The use of airborne electronic instruments for geodetic distance measurement and the determination of ground elevations. 3. Airborne geophysical surveying. 4. The extraction of qualitative and quantitative information from aerial photographs through the processes of "reading", analysis and interpretation. Many sciences and techniques are combined in aerial survey operations. The tools of the business include aircraft, finely engineered cameras, elaborate film processing and printing equipment, ground survey instruments, precision stereo-plotting instruments, map -

Jan 1, 1961

By P. Henry

Hydrometal provides an adequate technology to reintroduce lost metal units into the industrial cycle, thereby saving resources and energy, while keeping the environment cleaner. Two case studies of our integrated hydrometallurgical recycling facility (Hydrométal) in Belgium are discussed.(I) Recycling of Cu-Co cement generated at the second purification step of zinc sulfate solution. (II) Recycling of lead complex materials from the lead industry.

Jan 1, 2008

By Halet. R. A.

"The Quesabe Mine, owned by Brunston Mines Limited, is a gold deposit in the south central part of Duprat Township, northwestern Quebec, about 10 miles northwest of Noranda.It is one of the few gold mines in Canada developed since World War II. The occurrence of gold in the Quesabe fault structure has been known for many years, but serious exploration did not begin until 1945. By 1949, 15,000 feet of diamond drilling had been completed and a shaft sunk to a depth of 635 feet, with lateral development on the 450 and 600 foot levels. In 1949 and 1950 a new shaft was sunk to 1,050 feet, new levels were established at 800 and 1,000 feet, and ore was mined and shipped to the Noranda smelter. After November 1950 the ore mined was treated in the company's own mill. The grade of ore was marginal under existing economic conditions, and production was suspended in April 1952. The mine produced about 100,000 tons of ore with an average grade of approximately 0.25 ounces of gold per ton.GeologyThe bedrock formations are all Precambrian, and the general geology of the area has been described by W. G. Robinson (1). The rocks in the vicinity of the mine are acidic and basic volcanics of the Keewatin series (andesite, rhyolite, agglomerates, tuffs) invaded by the Flavrian Lake granite stock, and by dykes and irregular masses of intrusive felsite, quartz porphyry, syenite-porphyry, diorite, and lamprophyre.The mine workings are in andesite and felsite, about 2,500 feet west of the western margin of the Flavrian Lake stock.The principal structural feature of the area, from an economic point of view, is the Quesabe fault. This steeply-dipping fault cuts all the rock formations of the area, and has been traced for about 11 miles along a strike of north 65 degrees east from Lake Arnoux in the northeast corner of Dasserat Township to Duprat Lake near the east boundary of Duprat Township."

Jan 1, 1949

By M. Mirnezami, J. A. Finch

The McGill component of the consortium contributed detailed examination of the electrokinetic properties of the constituent minerals, primarily pentlandite and serpentine. Mineral specimens were derived from an ore sample; mineralogical examination showed the serpentine was predominantly clinochrysotile, a fibrous mineral responsible for much of the flotation separation problem. The study included design of a novel sedimentation potential measuring device to classify the surface charge of the ore and electrophoresis measurements on single and mixed minerals which progressively approached flotation conditions. The sedimentation potential measurements provided a general association between surface charge and the visual state of aggregation as a function of pH. The electrophoresis experiments started with single minerals in a background of indifferent electrolyte and progressed to mixed minerals in a background of supernatant derived from an ore sample. The single mineral tests supported the suspected electrostatic interaction, i.e., hetero-coagulation, at flotation pH 9-10. The mixed mineral tests demonstrated this interaction and also revealed hetero-coagulation with Mg(OH)2 precipitates, derived from the supernatant. This interpretation was confirmed by optical and electron beam imaging. A series of agents, CMC, polyphosphate, soda ash, EDTA, were examined to disperse the system. To accommodate the small mass of single mineral available a novel turbidity measurement using a UV/Vis spectrophotometer was introduced. Selected conditions were used in contact angle and small-scale flotation tests.

Jan 1, 2011

By V. S. Papezik

Pyrophyllite, a hydrous aluminium silicate, is used mainly in the ceramic industry and to a lesser extent as a filler in the manufacture of paper, rubber, insecticides and baby powders. Commercial deposits of pyrophyllite in North America are restricted to the "Avalon Zone" , a belt of late Precambrian volcanic and sedimentary rocks that extends along the eastern flank of the Appalachian orogenic belt f rom Georgia to Newfoundland. The only commercial Canadian pyrophyllite deposit lies near Foxtrap on the A valon Peninsula of Newfoundland. Here, steeply dipping lenses of altered pyrophyllite rock occur in a north-trending rhyolite belt near the contact with a granitoid pluton. The altered rock is massive, light greenishyellow and contains varying proportions of pyrophyllite, sericite and quartz with lesser amounts of diaspore and traces of barite and rutile. A lteration was produced by acid solutions, either derived from or activated by the intruding pluton, at temperatures of 250° to 270°C and pressures not exceeding 2 kbr. The largest of the Foxtrap pyrophyllite lenses, discovered in 1897, was mined intermittently f rom 1903 until the early 1950s. The present owner of the mine, Newfoundland Minerals Limited, acquired the property in 1959 and ships between 27, 000 and 36,000 tonnes annually to th e company plant in Lansdale, Pennsylvania, for use in ceramic tile.

Jan 1, 1984

"The North Star and Don Jon copper deposits lie beneath the waters of Thompson Lake, which is 12 miles east of Flin Flon, Manitoba. The deposits were discovered during the years 1949 and 1951 by diamond drilling done in the vicinity of pyritic showings on the shores of two small islands in the lake. The Don Jon ore body lies 1, 700 feet southeast of the North Star orebody and is connected with the North Star mine workings by a crosscut on the 600-foot level (Figure 1 ).Production began on January 1, 1955, at a combined rate of 200 tons per day. The ore is trucked, on 24 miles of highway, to the Hudson Bay Mining and Smelting Co., Limited mill at Flin Flon.Regional GeologyRocks in the Thompson Lake area are Precambrian volcanics, ranging in composition from andesite to rhyolite, with related tuffs and breccia. These rocks have a general north-south trend and are steeply dipping. The area is part of the Lac Aimee fault block, which probably is the southward extension of a south-plunging syncline now thrust some miles to the north. This regional deformation has produced many subsidiary zones of intense shearing and crumpling. It is in two of these zones of shearing and drag-folding that the orebodies occur. The only recognizable intrusive is a narrow diorite sill which trends northeasterly near the west shore of Thompson Lake.The North Star MineA pyritic showing, carrying some chalcopyrite, was discovered around the year 1930 on the west side of a small island near the west shore of Thompson Lake. This ground was included in a group of claims acquired by the Hudson Bay Exploration and Development Co., Limited in 1947.In the years 1949 to 1951, a diamond drilling program outlined a copper sulphide orebody. This ore zone comes to surface beneath the lake, about 300 feet north of the pyritic showing on the island."

Jan 1, 1949

By Alex McEachern

MINING LEADS WAY TO PROSPERITY THE year 1937 will stand out in the history of mining and metal products in Canada as one of which we shall always be proud. The combined contribution of these industries played a large part in leading Canada back to prosperous conditions after years of stress and strain that left their mark upon business the world over. A review of general industry shows a marked improvement over recent years. The upward trend continued un-abated most of the year and not a few of the industries had all they could do to supply the demands. A fact that should be appreciated in a year of wheat failure over an extensive area of the Prairie Provinces is the shifting of the basis of Canadian prosperity from agriculture to that of mining and the use of metals. To the great demand for minerals of all kinds, our mines have well responded and many new high levels were reached. This reflects great credit upon the men who direct the activities of the Canadian Mining Industry. Possessed by a spirit which refused to accept defeat in 1931-1932, they began to increase the efficiency of their departments, explored all channels hitherto untried, and won through to a crowning success. Who among them dreamed that their country's extremity would be their Alex. McEachern opportunity, and that through their united efforts our young nation would be enabled to hold that high position she has attained in world affairs?

Jan 1, 1938

By C. E. Cartwright

That the construction of the Pacific Great Eastern railway has not been accompanied by an immediate and great development of traffic is not due to lack of natural resources in the district traversed, but to conditions that have delayed their development. Prior to the commencement of construction of the railway there was no inducement to prospect for any other mineral than gold, on account of lack of transportation. The war began soon after the commencement of construction; diverting practically all capital that might have been available for opening up the country; and since the war, capital has continued shy of new investments. If the war had not occurred it is probable that prospecting and development would have been carried out concurrently with the railway construction. Moreover, much of the district is covered deeply with drift, marine and alluvial deposits, rendering prospecting for lode mines a more expensive and slower proceeding than can generally be undertaken by the ordinary prospector, without capital. On the other hand, the presence of large porphyry dykes, granitic intrusions, and the finding of rich float in places are indications that rich miIY.ral deposits probably exist in several localities in the Lillooet district, in the Cariboo proper, and also nearer the coast. Two or three mines producing the tonnage of the? Britannia would materially alter the earnings of the railway and pay interest on the bonds. There are, however, other possibilities, in addition to large metaliferous mines, in the non-metallic minerals of the district.

Jan 1, 1925

By Kristine Haug

Although most in situ operations in Alberta do not encounter significant problems during resource extraction, there have been a few documented occurrences of oil or steam releases as a result of compromised caprock seals. The objective of the Oil Sands Caprock Integrity Project (OSCRIP) is to characterize the units above and below bitumen zones to determine which geological factors affect the quality of the caprock seal. In addition, geomechanical properties and stress measurements of the bitumen reservoir and overlying units will be examined to provide a better picture of the containment conditions in which in situ operations occur. The information from this study will aid regulatory staff and industry in determining the zone-specific geological and geomechanical factors that could affect the design, operation, and feasibility of in situ recovery projects. The OSCRIP study area (Townships 87 to 99 and Ranges 1 to 13, West 4th Meridian) encompasses the surface mineable area, the northeast extent of the Wabiskaw-McMurray bitumen deposit and the Clearwater Formation, as well as a wide band of the Devonian salt-dissolution zone. Regional geological mapping of the Cretaceous strata focuses on the spatial extent and thickness of the caprock seal. Mapping of the underlying Devonian strata is targeted at better understanding the potential effects of salt dissolution and collapse of overlying strata on the integrity of the caprock seal. Examination of LiDAR (Light Detection And Ranging) bare earth DEM in the study area has revealed localized depressions that may represent sinkholes rooted in subsurface collapse features in Devonian carbonate and evaporite strata. Mapping the location and understanding the timing of salt dissolution-related features and deformation in the Devonian strata will help address questions about the possible effect that geological structures, such as sinkholes, have on the integrity of the caprock, as well as the potential for localized variations in the stress regime of the bitumen zone and overlying units. The stress regime in units above 350 m is such that any induced fractures are believed to be horizontal, and therefore, there would appear to be no mechanisms that would allow these fractures to reach the surface. However, recent incidents have shown that vertical pathways can occur, linking the subsurface to the surface. The final phase of the project will evaluate the changes that may occur in the stress regime under thermal operating conditions in the study area.

Jun 1, 2012

By H. B. Lumsden

This paper is intended to deal merely with the commercial development of some of the principal non-metallic mineral resources in the three prairie provinces- Manitoba, Saskatchewan, and Alberta. Coal is not included in this summary. Building Stone First and foremost, mention may be made of the building stone now being produced at Tyndall, Manitoba. This is a mottled limestone and is declared by experts to be one of the finest building stones in America, both as regards durability and appearance. It has been used very extensively both for exterior and interior work, not only in western Canada, but also in the principal cities as far east as Montreal. The stone is the "'Upper Mottled Limestone", which forms the summit of the Trenton (Ordovician) strata in the Lake Winnipeg basin. Quarries are at present being operated at Garson and Tyndall . The area where this stone is known to be available extends in a north and south direction for a distance of three miles, and the main productive ridge is probably about one half mile wide. The outlook for the future of the industry is extremely promising, as the stone is becoming increasingly popular in Eastern Canada, more particularly for interior work.

Jan 1, 1928

By R. E. Dye

IF gold mining is to assume, or it might be better said to resume, a place of ' importance in the national economy of this country following the present war, then one must accept the thesis that gold will maintain the place it has for many generations held in the minds of men as a substantial and lasting emblem of material wealth-a metal in exchange for which men have always been ready to give up the possession of their worldly goods. The thought bas been advanced by some that gold is not necessary as a basis for exchange, that it has no real value anyway and, therefore, the world would wake up some morning to find that no one wanted gold and that, over night, its possession bad in some way ceased to be desired. Holding an equally extreme view there are those who advance the idea that, following the war, gold will in some mysterious way enjoy a fantastic increase in value. Neither of these extreme views can be successfully supported. To presume that by legislation or by general agreement gold would be or could be, over night, dethroned to the position of common stone is wholly beyond the realm of any possibility. The thought that this could come to pass is advanced by, and is attractive to, only those peoples who do not have gold and do r:ot have the means of producing it. To believe that the fundamental value of gold will suddenly change is likewise fantastic. I refer to the fundamental value, not the dollar price, of gold, for it cannot be denied that, with the colossal war expenditures now being made and with the huge national debts which are being piled up, there is a possibility, indeed per-haps a likelihood, that the dollar price .of gold may be revised upward. For the purpose of this discussion, however, that possibility is irrelevant and need not be considered.

Jan 1, 1943

By Horace Freeman

Introduction In the aggregate, directly and ?indirectly, the pulp and paper industry ? consumes very large quantities of a variety of minerals, or compounds prepared from minerals. This is especially true in the manufacture of news-print, but fine papers, also, account for some of this consumption, in the processes of loading, coating, and otherwise improving the finish. The more important of the minerals used in the industry in Canada are briefly dealt with in the following pages. The list is by no means exhaustive, however. Thus, barite, lithopone, zinc oxide, zinc sulphide, and titanium oxide are used in small quantities in Canada in filling and coating paper. Up to the present time, however, the quantities of these materials used in the paper industry have not sufficed to encourage their manufacture in Canada. In the case of barite (barium sulphate)-or of witherite (barium carbonate)-it may be said that, should deposits of commercial size be discovered in Canada, the ore would have considerable export value, for use in the paper and other industries. China-Clay (Kaolin) Considerable quantities of china-clay are used for brightening and improving the finish of paper, and there is a growing tendency to use larger amounts of this material in newsprint manufacture. No china-clay suitable for paper manufacture is at present produced in Canada, but samples have been forthcoming recently from a deposit near St. Remi d'Amherst, Labelle county, Que., about thirty miles north of the Ottawa river and approximately midway between Montreal and Ottawa, and plans are under way to conduct large-scale tests with this material. Present sources of supply are the United States, England, and Russia.

Jan 1, 1934

By Jayesh B. Patel, Zhongyun Fan, Hu-Tian Li

"Melt conditioned direct-chill (MC-DC) casting is a novel technology which combines vertical direct-chill (DC) casting with a high shear device directly immersed in the sump for in situ microstructural control. In this paper, the solidification mechanism of DC casting under varying conditions is discussed. The temperature profiles in the sump were measured under the steady state casting conditions by using sacrificing thermocouples. Detailed comparisons of the derived thermal condition are made. The individual role of grain refiner additions, natural thermosolutal convection and forced convection in the sump and the interplay of these factors in determining the solidification structures of DC cast billets are discussed. The MC-DC casting technology can be used to control microstructural constituents and casting defects in DC cast billets/ingots by in situ manipulating of the thermal and fluid flow conditions.INTRODUCTION Direct-chill (DC) casting of aluminium, has been the essential commercial process for producing feedstock suitable for subsequent processing, such as extrusion, rolling or forging. Fine and equiaxed grain structures in the as-cast billets/ingots are required to enable a fine and uniform distribution of second phase particles and microporosity. This leads to higher productivity, more cost-effective homogenisation and more efficient downstream thermomechanical processing. The addition of chemical inoculants has been the standard industrial operation prior to casting for grain refinement of Al alloys. However, it has been established that less than 1% of the grain refiner particles added actually act as heterogeneous nuclei to refine the grain structures, showing a very low grain refining efficiency (Greer, Bunn, Tronche, Evans, & Bristow, 2000). Moreover, the remaining particles from the grain refiner addition in the final casting may cause surface defects during downstream processing. A major issue of the metallurgical quality of large sized ingots/billets is the non-uniformity of microstructures even with chemical grain refiner additions. This is due to the fact that the grain structure formed in the different zones of the billet depends on the local chemical composition and local cooling rate. The local cooling rate can vary from 0.4~1 K/s at the centre of the billet to around 10–20 K/s at its surface zone (Nadella, Eskin, Du, & Katgerman, 2008). The large thermal gradient along radial direction between billet surface and interior of the melt during conventional DC casting induces thermal stress and cold cracking even with grain refiner addition. Therefore the control of casting defects, such as macrosegregation, porosity, cold/hot cracking and distortion of the billets/slabs, etc., is still challenging in industry, causing high scrap rate of DC cast ingots/billets even with grain refiner addition."

Jan 1, 2018

By S. Southall, F. McCaffrey, F. Stober, M. Darini

Electrode Columns are commonly used in electric furnaces to deliver current and regulate furnace power to the smelting or melting process. Hatch has developed an innovative patent-pending system for lowering ("slipping") and/or raising ("back-slipping") the electrodes through an electrode column, without requiring the release of any clamping devices. All clamping forces are applied by springs. Unlike systems employing hydraulically applied clamping forces, (e.g., water bladders) the spring system is failsafe. Its inherent simplicity virtually eliminates the need for maintenance. The Hatch system is particularly applicable to Soderberg electrodes, and comprises two axially movable slipping clamps and a stationary power clamp, each of which apply a distributed, radial clamping force to the electrode. The magnitudes of the slipping sleeves' clamping forces and sequencing of their axial movements are selected such that the slipping clamps, in conjunction with the weight of the electrode, provide slipping or back slipping without release of any clamping force.

Jan 1, 2005

By F. Liu, H. A. Meier, D. M. Valiveti, P. A. Gordon

Hydraulic fracture is a frequently used technique in the Oil and Gas industry to create high permeability pathways for extraction of hydrocarbons. Numerical simulation of this method poses challenges such as representation of 3D fractures, propagation of randomly oriented fractures in 3D media, enabling fluid leak-off from fracture to poro-elastic medium. We have developed a numerical model using the Generalized Finite Element Method (GFEM) to simulate fluid driven fracture in a poro-elastic medium that addresses these challenges. In the GFEM framework, special enrichment functions are used to augment the solution space in the displacement and pore-pressure fields in order to accurately capture the response in the vicinity of the fracture. Adaptive refinement of the finite element mesh is also employed to facilitate accurate and efficient solution of the model. Our model fully couples fluid flow in the fracture, represented with the lubrication approximation, to the geo-mechanical behavior of the bulk poroelastic rock, comprised of an elastic rock skeleton saturated with fluid. Fracturing fluid exerts traction on the fracture surface and is also allowed to leak-off into the poroelastic medium using a transfer function approach. Stress intensity factors (SIFs) are evaluated based on the Contour Integral Method, accounting for the fluid pressure on the fracture surface. The SIFs are used to govern a full 3-D evolution of the fracture. Verification of the model is performed for known behaviors for the poroelastic response and fluid flow in the fracture.

Jan 1, 2015

By V. L. Mitsopoulos

This paper provides a summary of tailings disposal techniques and the improvements that have been made through the introduction of thickened tailings disposal. The general properties and characteristics of thickened tailings are described, as is a design process for selecting appropriate technologies for thickening, pumping, transporting and storing tailings. The factors affecting the selection of an appropriate disposal site and operational considerations for the effective utilisation of tailings storage areas are also documented.

Jan 1, 2006

WHAT IF? ?Mine closure and reclamation liabilities were fully funded -at all times from current mine revenues ?Unexpected & catastrophic events were insured ?Remediation costs could be capped ?Risk management was improved ?best practice and independent oversight ?Host communities?concerns were adequately addressed If this could be achieved within a cost-effective financial structure, this may be a solution to a complex issue for the mining industry

May 1, 2006

By Tim Bekhuys

Equator Principles ? Applies to projects > $10 million ? Voluntary agreement between 58+ EPFIs ? Categorized projects based on environmental risk, consequences ? Requirements for EA, EMP, use of safeguard policies, consultation ? IFC Performance Standards on Social and Environmental Sustainability ? Apply if the project is in a low or lower-middle income country ? Low-middle income countries defined by the World Bank Development Indicators Database

May 1, 2008

By Peter D. Cunningham

At Vale Inco in Sudbury, underground mobile equipment production and maintenance data is presently collected manually from paper slips. This paper reviews a pilot project that developed a system to electronically collect that data. The benefits and improvements in data accuracy, timeliness and reduction in collection effort, will be discussed. Technological issues that arose from the use of WiFi, RFID (Radio Frequency Identification) and the IREDES mine data equipment standard are also discussed.

Oct 1, 2009