Search Documents

By G. E. Agar

"The distribution of gold in the grinding-classification circuit of an operating gold plant was determined by assaying the size fractions of samples from each of the streams. This analysis identified the streams with the maximum potential for gravity recovery of gold and revealed that there was up 110 seventy-five times as much gold in the primary cyclone underflow as in the concentrator feed.Laboratory jigging and tabling tests were done on samples from two of the streams to determine what the recovery might be with a gravity circuit and to show that a high grade concentrate could be produced. A numerical simulation procedure was used to calculate a material balance for a circuit that included gravity separation on the primary cyclone underflow. The numerical simulation optimistically indicated that as much as 84% of the gold might be recovered in a reasonable grade of concentrate even though the recovery in batch bench scale tests was only 14%.Incorporation of a gravity separation device would reduce the inventory of gold in the grinding-classification circuit.INTRODUCTIONMany gold concentrating plants include a gravity concentration operation while others do not and the reasons that some do and some do not is not clear. Some of the advantages and disadvantages of gravity circuits are discussed by Penman (Penman 1987) without clear cut resolution. Penman's comments elicited an interesting response from Lloyd (1989) who produced a simple way to determine if the addition of a gravity concentration circuit would enhance the recovery of gold. Lloyd's method does not consider the cost of running the circuit so it only partially answers the question. There are reports in the literature (Wells and Patel 1991, Matwijenko 1988) that as much as 60% of the entire production comes from a gravity circuit when it is used, and that the grade of the concentrate produced often exceeds 65% gold, an assay that far exceeds most Merrill-Crowe precipitates that are sent to refining. In at least one instance (Hood 1984) a range of recovery from 40-50% was indicated from laboratory test work and the plant subsequently realized recoveries in the range of 26-40%. Despite these favorable numbers other plants use gravity separation when as little as 20% of the gold is recovered in the gravity concentrate (Carter 1992)."

Jan 1, 1993

By G. E. Parsons

"The Bidgood is a small gold mine about 5 miles east of the main Kirkland Lake camp. Since the beginning of production in 1934, gold having a value of $5,000,000 has been produced from the property. Practically all of this production has come from seven veins in a diorite stock that intrudes the Timiskaming sediments and lavas of the area. The veins consist of quartz, pyrite, and molybdenite with minor amounts of chalcopyrite, calcite, and tellurides, and occupy northeast striking and northwest dipping thrust fault fractures. They have no apparent direct structural association with the faults of the main Kirkland Lake camp or the Larder Lake 'break' to the south; however, the veins closely resemble the former in their mineralogical composition and in their close association with syenite intrusives.ROCK TYPES AND THEIR STRUCTURAL CHARACTERISTICSThe dominant and, from an economic standpoint, most important rocks in the ore area consist of two separate families of Algoman intrusivesa diorite and a later syenite group."

Jan 1, 1954

By A. R. Laplante

"In this paper, the performance of the Knelson Concentrator and of the batch and continuous Falcon Concentrators are compared. The units are based on different operating principles, and as such they perform quite differently. The Knelson yields very high free gold recoveries over a wide size range of both the recovered and rejected species. It is ineffective in recovering very fine ( <15 µm) or flaky gold, as encountered in flotation feeds, concentrates or tails. It is the: preferred unit for gold recovery from grinding circuits. The batch Falcon is effective in the fine range, typically less than 37 µm for gold. Its recovery zone is quickly saturated when there is significant heavies in the feed. It works best as a pre-concentration unit. The continuous Falcon is a versatile unit which is capable of recovering fine heavies (density down to 5 g/cm3 ), especially from coarser gangue. INTRODUCTIONThe purpose of this presentation is to describe the mode of operation of two Canadian centrifugal concentrators, the Knelson and Falcon. It is hoped that it will prove informative to prospective users in the selection, testing and optimization for applications of either machine. The work is based on testwork both in Canadian mills and at McGill. I am indebted to many colleagues at these locations. Appropriate references will be made to articles further describing the work, either already in the open literature or in preparation.Although this work is meant to be more practical than scholarly, it is appropriate to begin by considering how the two units achieve selective recovery. This will become useful in establishing a suitable testing methodology, which will then be described, and interpreting typical results. In the last section I will attempt to define appropriate applications for the two units. This is a thankless task, as I am likely to miss some applications or to make projections based on partial results, as much of the work is still in progress. In deference to the reader and both manufacturers, areas where reasonable doubt still remains will be identified."

Jan 1, 1993

By Chris J. Pritchard

Pumpable, two-component resins for anchoring rock bolts provides significant advantages over traditional cartridge resin and cement grout systems where fast and easily adaptable support is required for difficult ground conditions. Cartridge resin anchoring with rock bolts is often ineffective in oversized, fractured and washed-out holes. Cement grouting of cable bolts is frequently plagued with QA and QC issues related to the grouting process. Installation of cable bolts with resin injection techniques is routinely completed in cycle allowing blasting immediately after cable bolting. Xstrata Nickel has evaluated the Minova Resin Injection System since 2007. The Nickel Rim Mine and partner Minova have tested and validated the Resin Injection process for bolting procedures including Hollow Fiberglass Bolts, Rebar, Modified Cone Bolts and Cable Bolts. The resin injection process is adaptable to most bolting processes and equipment. Currently, Nickel Rim Mine use 2 resin injection products with different set times to grout deep cable bolts and development support in highly variable ground conditions. The product predictability and adaptability in application along with a high crew acceptance continues to make this support process part of an adaptable ground support system. Product consistency and quality significantly reduce the quality control concerns for ground support in highly variable ground conditions.

May 1, 2011

By Zia Pirzada

"Time is of the essence" and "Time is money" These are powerful and true statements during a project life cycle and have far-reaching implications on the success and failure of the project Time and progress management is crucial to the project success. Project delays may increase the cost to an unacceptable level and may render the project as economically unfeasible. On the other hand, if the project is completed on time or earlier than as planned, it may generate economic benefits greater than what had been envisioned To take advantage of the financial opportunities and to improve the cash flow as well as Return On Investment (POI), project schedule can be accelerated to complete the project earlier than planned Project schedule acceleration can be achieved by using analytical tools, such as "Schedule Optimization", "Schedule Reduction", "Schedule Compression" or a combination of any of these concepts along with the "Planning for start up". Schedule optimization does not entail any extra cost, however, other acceleration methods, such as Schedule Reduction and Schedule Compression, may require extra expenditures from the owner. Based on the forecasted early start of the revenue stream, the extra expenditure could become a worthwhile venture with a very high rate of return To accelerate the schedule, all aspects of the project should be reviewed with acceleration costs calculated. All risks and opportunities should be evaluated and taken into consideration to determine if the acceleration is feasible and advisable and will provide definite financial advantages Sometimes schedule acceleration may be desired to prevent the company from paying liquidated damages. This is especially true when the project is not expected to complete on the contractual completion date and when the cost of acceleration is less than the liquidated damages that may accrue against the company.

Oct 1, 2010

By A. J. Rigby

The wear mechanisms of the tuyere lines of Peirce-Smith and Hoboken converters are a subject of endless debate and speculation. However, there has been an indication that one of the primary factors in the deterioration of tuyere lines is due to the batch operation of the converting process. The cooling of the brick in the tuyere line during out-of-stack times leads to shrinkage of the brick and resultant opening of the joints. Subsequently, on re-entry of the tuyere line into the bath, the joints become penetrated with matte and re- expansion of the brick is prevented. It is thought that this regular cycle of exiting the batch for slag skimming and replenishment of matte and re-entering for further blowing leads to a gradual “ratcheting” of the tuyere brick lining. If no expansion allowance is furnished between the endplate and the endwall of the lining, then the generation of damaging compressive stress is unavoidable. INTRODUCTION It is generally accepted industry-wide that the integrity of a refractory lined vessel is determined by an inextricable combination of refractory brick quality, the caliber of the lining design and installation, and the severity of the process inflicted upon the high wear areas of the vessel lining. Rigby has summarized the concentrated attempt, over the past several years, to optimize the microstructural, chemical, and fracture properties of the refractories used in non-ferrous pyrometallurgical vessels. Furthermore, lining design concepts involving larger and longer brick and the extent and positioning of expansion allowance in the joints have been extensively trialed. All these efforts have provided some, but not startling, improvements. The simple fact is that a vessel lining composed of bricks with an optimized microstructure and chemical inertness must installed with a well-conceived design to decompress the lining stresses that are generated by the batch operation of copper converters. REFRACTORY QUALITY Converting is conducted by injecting air into the molten matte and white metal for the very purpose of generating iron and copper oxide slags. These slags must be contained by a refractory which, by its mineralogical formulation, is optimized for chemical inertness.

Jan 1, 2019

By George W. Bain

The area in Quebec immediately north of the Ottawa river is underlain by a large area of granite gneiss intruded in lit-par-lit fashion into Grenville sediments and low silica intrusives of the Buckingham Series. This complex of metamorphic rocks is intruded by a much later magma found, chiefly, as a very large stock about 20 miles in diameter and extending from Brownsburg to Grenville, and as dykes and small outliers at various places adjacent to its outer margin. 1A similar stock at Rigaud, Quebec, is situated south of the Ottawa river and has been described by O. E. Le Roy. The earliest representatives of the later magma are a series of granodiorite dykes characterized by abundant hornblende, along with primary magnetite and subordinate sulphides scattered as roundish grains through anorthoclase and aligoclase feldspars and subordinate quartz. The rock is found as narrow dykes and shows no prominent secondary structures, either in the field or in thin sections under the microscope.

Jan 1, 1926

By T. Kagawa

Ever-increasing demands for non-ferrous metals owing to population growth and improvements in the standard of living in the world, under the constraint of limited availability of natural resources, would easily make us imagine that more efficient and sustainable developments in mining and smelting activities are required in the near future with due consideration for environmental concerns. In order to realize the efficient and sustainable development of mining and smelting activities and operations, the following issues are indispensable: (1) to investigate the up-to-date pollution control technologies of mine and smelter, (2) to promote those technologies, (3) to develop technologies which are environmentally friendly. This paper discusses the recent technologies for environmental conservation/prevention and their diffusion in the world, and also the key technologies required for the most desirable sustainable development.

Jan 1, 2007

By DON E. MacDONALD

Marl in Alberta is confined to highly specific geological, hydrogeologica/ and climatic settings. Tufa is fa irly abundant in those areas of western Alberta where bedrock is of the Paskapoo Formation. Marl and tufa originate when the following conditions are met: presence of a carbonate source in drift or nearsurface bedrock; leaching of the carbonate by percolating groundwater; transportation of calcium and bicarbonate ions in a permeable aquifer; discharge at the surface as springs, seeps or lakes; re-precipitation of calcium carbonate. Alberta has seven categories of marl and tufa deposits, based upon over-all depositional environment and calcium carbonate

Jan 1, 1984

By DAVID C. MILLER

Barite deposits occur worldwide and in a variety of geological environments. In recent years, several deposits of barite and barite-lead-zinc have been discovered in northern British Columbia, Yukon Territory and Alaska. Most are associated with Devonian-Mississippian age sediments, and many are syngenetic, bedded-type deposits. The Mel is a barite-lead-zinc deposit; it lies within Lower Cambrian strata and appears to be of epigenetic replacement origin. Figure I is an aerial view of the property from the south. Observations herein described are based largely upon field work, megascopic studies and two recent B.A.Sc. theses (Biasucci 1979, Rennie 1979).

Jan 1, 1984

"Previous studies on the effect of polytetrafluoroethylene addition during chalcopyrite leaching under conditions similar to those of the CESL process have reportedly resulted in complete leaching of the copper without the need for grinding of the flotation concentrate. However, these studies employed a pulp density of only 1% and finely sized PTFE particle that required the use of high impeller rotation rates that are not sustainable at an industrial scale. This paper explores the performance of 1/8” diameter balls of PTFE, that readily sink in the leach solution, on leaching performance at impeller rotation rates and ore pulp densities more typical of industrial practice. Possible routes for separation of the PTFE from the leach residues and their regeneration for recycling back to the leaching stage are also discussed.INTRODUCTIONChalcopyrite, CuFeS2, is the most important primary sulfide source of copper. While pyrometallurgical smelting of chalcopyrite remains the only widely accepted route for treating chalcopyrite concentrates, several medium temperature pressure oxidation processes are claimed to be economically feasible (Muir & McDonald, 2007). Among these, the CESL process has been extensively piloted and demonstrated at the prototype scale. The overall process chemistry of the CESL process may be summarized as follows (Marsden & Wilmot, 2007):4CuFeS2 + 5O2 + 4H2SO4 ? 4Cu2+ + 4SO4 2- + 2Fe2O3 + 8S0 + 4H2O (1)4CuFeS2 + 17O2 + 2H2SO4 ? 4Cu2+ + 10SO4 2- + 4Fe3+ + 2H2O (2)Though copper extractions of over 95 % are achieved, the CESL process requires extra grinding of the concentrate (Muir & McDonald, 2007). This is because leaching is conducted at temperatures around 150 °C, where the elemental sulfur produced is molten and grows thicker on the mineral’s surfaces as oxidation progresses, creating an increasingly large barrier for mass transport. In addition, the sulfur is sticky and tends to cause the mineral particles to agglomerate, effectively halting further oxidation of the particles that end up embedded within the agglomerates. Consumable surfactants, such as ligin sulfonate, have been shown to be effective at avoiding agglomeration, but they are not effective at removing sulfur from the minerals. Hence, their use does not obviate the need for fine grinding."

Jan 1, 2012

By Masashige Makifuchi, Hiroki Kumakura, Kota Nagai, Takahiro Kikuchi

"A large amount of platinum group metals (PGM) are used in automobile catalyst. It is important to recover the metals from wasted catalyst. Nomura and Kageyama (2013) suggested recovery process that PGM oxides were absorbed to perovskite-type oxide based on LaScO3. In their process, the PGM in wasted catalyst as absorbed to the perovskite-type oxide as PGM oxide. It has potential to each element in the process if the perovskite-type oxide is selected properly. In this study, the PGM oxide absorption properties of various perovskite-type oxides are investigated to develop a new recovery and separation process. The various perovskite-type oxide were synthesized with metallic platinum, palladium, rhodium at high temperature in air atmosphere. And the PGM contents in the perovskite-type oxide after the experiment are determined by chemical analysis. Some of them have the properties to absorb specific PGM oxide selectively. In addition, in order to increase the amount of absorption of PGM oxide and composition of the perovskite-type oxide experimental temperature was investigated. Then it is also found that doping another specific element to the perovskite-type oxide is effective to increase the amount of absorption of PGM oxide. Then a new recovery process of PGM from wasted automobile catalyst, in which PGM can be separate to each element, was designed.INTRODUCTIONA large amount of Platinum (Pt), Palladium (Pd), and Rhodium (Rh) are used in automobile catalysis (Figure 1) (Platinum, 2013). Natural supplies for these metals are limited and PGM mining can detrimental environmental impact. Therefore, the recycling of PGMs from wasted automobile catalysis is very important. The Rose process (Figure 2) was developed as a process to recover PGM from wasted automobile catalysis. In this process, the automobile catalysis is first crushed mechanically, and then extracting agent, copper (Cu), and flux are melted at high temperature. The mixture separates into a metal phase, (Cu alloy containing PGM) and slag. The PGM is enriched by oxidizing. Cu to Cu oxide. The PGM are then recovered and separated to each element in a wet process. However, it is hard to dissolve the PGM with acid because they are chemically stable and strong oxidation agent such as aqua regia is used. Moreover, to separate the PGM to each individual element, a solvent extraction process is required."

Jan 1, 2016

By RAYMOND C. HARTVIKSEN

The Drumbo Mine is located near Highway 401 between Woodstock and Kitchener in southwest Ontario. The tabular flat-lying gypsum bed is between 1.5 to 2.4 m thick and is situated near the base of the Salina Formation, about 116 m below surface. The mine is owned and operated by Westroc Industries Limited. The 3.8 m diameter shaft was drilled using a Hughes CSD 820 drilling rig and a liner sinking technique new to the North American continent. The shaft was completed in the fall of 1977, and remaining facilities were finished in the fall of 1978. Gypsum production started in December 1978, employing the conventional room-and-pillar method of mining.

Jan 1, 1984

By Kish. L.

"The results of a chemical and mineralogical study of eighteen opaque-oxide occurrences are discussed and the detailed chemical, metallurgical and mining feasibility study of a vanadium-rich magnetite deposit is summarized. A plot of the mol-percentages in the system FeO- Fe2O 3-TiO2 indicates that the deposits fall into two distinct groups: some contain hematite with ilmenite, and some others have magnetite with ilmenite (titaniferous magnetites). The plot also suggests that the two types of deposits were crystallized from liquids of different compositions. Each group has its distinct structural features. Vanadium is present in all of the studied specimens, however concentrations of economic importance have so far been found only in the titaniferous magnetite deposits. The vanadium content of the oxide concentrations of the Dore Lake Complex is the largest among the studied occurrences. Analyses of the concentrates of the drill-core sections show a compositional variation across the orebody; a continuous increase in the tenor of Ti02 and a decrease in the vanadium content upward in the layered sequence is found. Concentration tests on several tons of samples indicate that about 80 per cent of the vanadium is recovered in the magnetite concentrate."

Jan 1, 1972

By A. F. Gregory

"AbstractA resumé of aerial radiation survey studies performed by and for Eldorado Mining and Refining, Limited, since 1943 is presented. Flight tests were initiated in 1947 and were followed .by intensified use and study of Geiger counters and other radiation detectors. Development of an aerial scintillation counter began in 1948, but •a sensitive large crystal unit was not available for exploration purposes until 1950. Modifications of this unit have been used in all subsequent surveys.For the Eldorado detector, several limiting conditions were established for successful radioactivity detection, the most important being that natural vein exposures can only be assuredly detected .at distances less than 150 feet. Sedimentary and pegmatitic radioactive occurrences can be detected at much greater distances. A helicopter investigation technique appears to •have •a useful prospecting potential.IntroductionAerial radiation surveys were first proposed in the early 1940's. However, it was not until 1949 that airborne detectors were extensively used in the search for radioactive minerals. Eldorado has flown about 50,000 miles of exploration flights, exclusive of tests, using a variety of •detectors and aircraft. Considerable data have •been gathered for .the evaluation of the several techniques employed. Much of the early work was performed with the co-operation of the National Research Council of Canada ( 1). More recent work was done in conjunction with the Commercial Products Division of Atomic Energy of Canada, Limited. The Development Department of this latter corporation designed and built the scintillation counter used in recent Eldorado surveys."

Jan 1, 1955

By G. Q. Zhou, H. C. Liang, X. D. Zhao

"This study describes the strain behavior in vertical shaft lining (VSL) embedded in thick soil deposits and its application in assessment of concrete deterioration. The observed strain in VSL continuously decreased companied by a sinusoidal fluctuation due to the influences derived from negative skin friction (NSF) and temperature. The increase in strain increment between peak and trough at each year and compressive strain level as the servicing time continued and VSL depth increased implies that the concrete strength was attenuated, and this attenuation was significantly dependent on the existing compressive strain level in VSL. The reliability of the proposed approach was validated by Schmidt Hammer Technique (SHT) – based concrete strength, and is applicable in concrete assessment and then fracturing prediction of VLSs in thick soil deposits.Concrete strength, Field monitoring, Strain behavior, Vertical shaft liningINTRODUCTIONOver 100 VSLs in Southeastern China subjected to an unpredictable fracturing as shown in Figure1, and there are over 1,000 VSLs embedded in thick alluvium su?ering from challenges of damaging and potential fracturing (Cheng, Yang, Zhou, Li, & Hu, 1993; Zhou, Cui, Lv, Huang, & Chen, 1999; Li & Li,2005). Therefore, a reliable assessment of these VSLs is significant to the normal servicing of mine shafts and the recycle of underground space when these mine shafts were closed.The continuous increasing of NSF induced by the drainage of water–saturated deposits well interpreted such extensive fracturing phenomenon, and it is universally regarded as the governing indicator to determine the VSL stabilization (Cheng et al., 1993; Zhou et al., 1999). Based on this recognition, the fracturing prediction and VSL strengthening according to the field monitoring on hydrogeological characteristics, servicing environments, and mechanical behaviors of VSL were carried out (Zhao, Zhou, Zhong, Zhu, & Liang, 2009; Liang et al., 2009; Xie, Lv, & Wu, 2014). As known, the compressive strain level in VSL and the in–situ strength of VSL concrete were the main factors to perform such fracturing prediction. However, the existing studies in literatures were limited to the strain accumulating or releasing behaviors (Zhao, Zhou, Zhao, Kuang, & Hu, 2017), and lack of considering the VSL concrete strength and its attenuation. In this reported study, the in–situ monitoring data on the strain in typical VSLs and the VSL elevations between 2004 and 2014 were initially analyzed. Then, an observed strain behaviors–based approach was developed to quantitatively evaluate the VSL concrete deterioration."

Jan 1, 2019

By E. S. Moore

DEEP oxidation and-secondary enrichment of ore deposits, although so important in many parts of the world, are comparatively rare in the Canadian shield. Intensive glaciation during the Pleistocene epoch accounts for their rarity. Glaciation has cost Canada much in the destruction of not only enriched ore deposits, but placers that must have been developed near our numerous gold deposits during the long period of weathering that pre-ceded the Pleistocene. There seems to be a very common misconception regarding the average depth of rock that has been removed from the shield by glaciers. These bodies of ice are usually given credit for the removal of the greater portion of the thousands of feet of rock that we know has been eroded from this large area since Precambrian time. As a matter of fact, the average thickness of solid rock removed can be measured in tens rather than even hundreds of feet, although very deep erosion has resulted in some sections where the glacial ice has been constricted in depressions, such as deep valleys and lake basins. On the other hand, there are few areas within the shield where the glaciers have not disturbed practically all of the mantle rock and some feet of the underlying bed-rock. The chances of finding deeply oxidized cappings and enriched ore deposits are therefore comparatively few and these have been found chiefly where favourable structural and topographic conditions for their formation and preservation have existed. Faulting has been responsible for several of these deposits, and easily decomposed rocks, such as. sulphides and carbonates, have been very important factors. Topographic features, such as high and resistant hills, favourably situated with respect to the ore deposits have, in a few cases, played a part in providing protection from glacial erosion and in furnishing head for the descent of surface waters. At least four cases of oxidation to depths quite abnormal in the Canadian shield have so far been found in Ontario. These are the Helen and Josephine iron mines in the Michipicoten district, the Keeley silver mine in South Lor-rain, and the Ross gold mine in Hislop township, Cochrane district. A deeply oxidized zinc deposit of unusual interest occurs in the Precambrian rocks in New York State, not far from the Canadian border, and there arc the well-known iron deposits in the Lake Superior region of the United States.

Jan 1, 1938

By L G. White

During 1958, prospecting parties working for the Mackenzie Syndicate in the Flat River area of the Mackenzie mountains, Northwest Territories, identified tungsten mineralization and located the property now being developed by the Canada Tungsten Mining Corporation Ltd. Scheelite mineralization, associated with pyrrhotite and minor chalcopyrite, occurs in lime silicate skarn replacement zones within a limestone-chert-argillite series intruded by granitic dykes originating from the ? main batholithic mass underlying the sedimentary beds. The results of surface outcrop sampling and 15,000 feet of grid-pattern diamond drilling have been combined to outline an orebody estimated to contain 1.32 million tons, grading 2.51 per cent WO after applying a 10 per cent dilution factor for mining purposes. T HE property of Canada Tungsten Mining Corporation Ltd. is located in the upper Flat River area of the Mackenzie mountains, Northwest Territories. Skarn-type replacement deposits containing scheelite mineralization are .situated between elevations of 4,500 and 5,500 feet above sea level along the east flank of the mountain range forming the boundary between the Yukon Territory and the Northwest Territories. The nearest supply center for the area is Watson Lake, Yukon Territory, located at Milepost 635 on the Alaska Highway.

Jan 1, 1963

By Leonardo F. Trivino

Despite the significant economical and safety implications of poor blasting practice in mining and quarrying operations, the default practice in many large operations, including both design and control, is considerably below standard when compared to other engineering disciplines. Blast dynamics includes a number of complex phenomena, such as the generation, propagation and interaction of stress waves, the expansion of high pressure, high temperature gases from the explosive components, and their combined effects upon the rock mass, including fracturing, fragmentation and displacement. In order to tackle this non-trivial problem, a combined finite and discrete element software (Y-code) capable of accounting for the dynamic behaviour of stress waves, simulating fracturing processes and modeling the expansion of gases is under development. The constitutive models used in this particular software are fundamentally simple, however, non-linearity and chaotic behaviour result as natural consequences of the interaction of relatively simple processes and mechanisms, such as propagation of stress waves in the immediate vicinity of the exploding borehole, and the creation and propagation of fractures. Advances on its development and comparisons with experimental data show realistic propagation of stress waves and fracture networks.

May 1, 2013

By N. Shi, T. G. Joseph

ABSTRACT A revised equilibrium approach to evaluate dipper-ground interactions during the dig cycle of ultra-class mining shovels operating in soft unblasted uniform ground conditions is presented. A review of previous approaches, leading to an outline of the modifications and ground condition considerations, is made in support of the reasoning and basis for the derivation presented. An analytical solution is provided to the scenario of a cable shovel dipper digging in soft ground material such as oil sands.

Jan 1, 2012