Search Documents

By Y. G. Yaroshenko, V. Y. Baldin, Y. M. Gordon

The manufacture of sulphuric acid from the off-gas of pyrometallurgical processes in the production of heavy metals is one of the common methods of effective recycling of sulfuric anhydrite. The new Impact-Inertial Devices with the rectangular contact channels (IIRCh) and the internal circulation of liquid allow the injection of an absorber into the phase's interactive cell by utilizing the gas stream energy and by this way increasing the sulphuric acid yield and reducing the power consumption. These devices have the following advantages: simplicity of design, smaller size, low capital expenses, absence of irrigating system, high operational reliability, simultaneous cleaning of solid, gaseous and liquid impurities and also cooling of gases etc. The IIRCh efficiency is almost 18 % higher and they require 1.3-2 times lower energy when compared with Venturi Absorbers. Also the elevation of spraying nozzles or injectors is 1.5 times lower in the IIRCh case.

Jan 1, 2004

By E. G. Gaylord

THE material improvements which have been made in the practice of exploiting oil and gas reservoirs in the United States during recent years may be attributed largely to: (1) The necessity for drilling deeper wells at costs not much greater than was formerly expended on shallower wells. (2) The necessity for producing oil at a lower cost per barrel. (3) A growing recognition of the importance of the nature of production practice upon ultimate yield of oil and gas. The first two of these factors result, to a large extent, from the fact that a greater proportion of new development has been deeper development, and these wells have been drilled in the face of progressively lower per well allowables. In California, for instance, maximum allowables have declined from 400 barrels per day in March, 1938, to 156 barrels per day in September, 1940, and during this same period some 125 wells were drilled to the deeper 10,000-foot producing horizons discovered during this time. The third item listed above results from our increasing knowledge of the basic factors which influence the amount of recovery we may expect from reservoirs. In addition to the longer-range planning now being undertaken by the more prudent operators, State proration and conservation laws have focused attention upon the importance of methods conducive to obtaining progressively greater quantities of the hydrocarbons in place. In a paper of this length it will be possible to discuss only a few of the recent advances. An effort has been made to select the more important of these and to indicate, where possible, the factors which have made these advances possible.

Jan 1, 1941

By M. Sahoo, P. Burke, Y. Fasoyinu, J. P. Thomson

The effects of grain refinement, mold temperature and chemical composition on the hot tearing resistance of aluminum alloys 535.0 and 206.0 has been studied by pouring constrained rod castings in metal molds. In addition, two prototype components that could be used in automotive applications were also poured from both alloys by gravity tilt-pour and low pressure permanent mold casting processes. This paper summarizes the results and issues encountered during the casting trials. It was shown that grain refinement and mold temperature ::::: 400°C reduced, and sometimes eliminated hot tear cracks in both alloys. The two prototype engineering components could be cast successfully from both alloys in metal molds. The metallurgical issues related to molten metal treatment and processing temperatures were well controlled. However, issues related to the control of hot tearing, casting and mold design must be addressed in future studies to guarantee the production of defect free castings.

Jan 1, 2006

By Neda Zangeneh

Production efficiency from low permeability gas shales require techniques to optimize hydraulic fracture completions. One completion strategy involves the simultaneous or near simultaneous hydraulic fracturing of multiple horizontal wells to maximize the fracture network area and stimulated reservoir volume. However, changes to the in-situ stress field caused by an earlier hydrofrac on subsequent hydraulic fractures are not accounted for in traditional hydrofrac design calculations. Presented here are the results from a set of transient, coupled hydro-mechanical simulations of a rock mass containing two wellbores using the discontinuum-based distinct-element method. The results demonstrate the influence of stress-shadows generated by a hydraulic fracture on the development of subsequent hydrofracs from an adjacent well. It is shown here that these interactions have the potential to change the size and effectiveness of the hydraulic fracture stimulation by changing the extent of the hydraulic fracture around the secondary well.

Jun 1, 2012

By J. M. Wolverton

CONSIDERABLE interest has always been taken in Safety-First and First Aid at the Sullivan mine. Even during the early days of development, Safety-First committees periodically held meetings, while lectures in first aid were given to any employees interested in the work. In 1929, a Safety Department was organized, and all accident-prevention and first-aid work was put in charge of a full-time Safety Engineer. An extensive programme has gradually been developed, the value of which can best be indicated by the reduction of the accident rate from 18.4 shifts lost per 1,000 shifts worked for non-fatal accidents and two fatalities for 1927, to 3.24 shifts lost per 1,000 shifts worked and no fatalities for 1936. SUPERVISION All work connected with accident prevention or first aid is under the jurisdiction of a central committee, known as the Accident Prevention Committee, which meets regularly once a month. It consists of all superintendents, department heads, foremen, and shift bosses, and is presided over by the Safety Engineer. At these meetings, the accident records of the previous month are reviewed and all accidents carefully analyzed and discussed. All proposed changes in the safety rules or in the accident tprevention programme are taken up and passed upon. Complaints or suggestions from the Safety-First Committee and the Employees Co-operative Committee, dealing with safety, are discussed and passed upon or a subcommittee is appointed to investigate and take any action found advisable. The question of underground ventilation and dust control, which recently has become a very important problem, always receives considerable attention.

Jan 1, 1937

By Muhammad Zaka Emad

ABSTRACT: Sublevel stoping mining methods with delayed backfill employs cemented rockfill (CRF) as a backfill material. It is used in underground mines to achieve ground control and reduce wall slough. In addition CRF serves to reduce development waste and provides a working surface for mining the upper levels. Efforts to optimize CRF practices have been published. This paper presents a detailed review of CRF practices in open stoping mining systems with reference to case studies. A new methodology is suggested in a simple stepwise approach, which can be adopted for site specific conditions. The need of laboratory testing and quality control program is discussed based on the published literature.

May 1, 2013

By Maurice Hall Haycock

ONE result of the higher price of gold has been the exploitation of many low-grade deposits, the successful treatment of which depends upon obtaining high recovery of the contained gold. Modern methods have made it possible to recover gold from many ores formerly regarded as impossible to treat economically, but in order to apply these methods efficiently it has become desirable, and indeed in many cases indispensable, to gain precise information concerning their mineralogical and physical character. The most successful means of doing this is the use of the reflecting microscope. Reflecting microscopes had long been employed by metallurgists for studying polished surfaces of iron and steel when, thirty years ago, Dr. W. Campbell, of Columbia University, advanced the idea of using similar methods for studying opaque minerals (1). The immediate result was the completion of two microscopic studies, the first on Cobalt silver ores (2) and the second on Sudbury nickel ores (3). The idea was surprisingly slow in being adopted, and not until 1911 did it begin to spread through the universities of this continent. From then on, ore microscopy, or 'mineragraphy', made rapid progress, and, during the next fifteen years, research in universities of North America and Europe led to the development of somewhat specialized apparatus and technique. This phase of development, which resulted largely in contributions of a descriptive nature, furnished a mass of data from which the possibility of economic applications was soon recognized. Ore microscopy became an aid to the mining geologist in solving many problems of ore deposition. This soon led to its application in the study of ores and mill products in connection with their treatment. Its usefulness in this latter field has been very marked and has led to its widespread adoption by the mining industry.

Jan 1, 1937

By Junhyun Choi, Allan Gomez-Flores, Chonbuk National University, Siyoung Q. Choi, Gahee Kim, Seungkon Kim

In this study, to confirm the effect of depletion attraction on the flotation, we theoretically and experimentally investigate the effect of the depletion attraction force on flotation. While varying the concentration of the depletion agent (polyethylene glycol), three different systems are studied: pure malachite, pure silica, and a 1:1 mass ratio of malachite and silica binary system. We find that recovery increases significantly as the concentration of the depletion agents increases for all three systems, as the depletion agent facilitates the adsorption of the particle on the bubble surface. However, the recovery suddenly decreases in a certain concentration range, which corresponds to the onset of the decreased surface tension when high concentrations of the depletion agent are used. This non-monotonic overall recovery trend implies the surface adsorption of the depletant on a surface. The decreased surface tension of the air/water interface suggests that the recovery rate is lowered due to the adsorption of the depletion agent to the bubble surface, acting as a polymer brush. Based on our observations, we conclude that the depletion force can greatly improve particle adsorption, as predicted in the accompanying theory paper, while simultaneously the adsorption of the depletion agent on the bubble surface plays an important role because it hinders particle adsorption. We also perform experiments in the presence of a small amount of a collector, sodium oleate. An extremely small amount of the collector leads to the increase in the overall recovery, which eventually reaches nearly 100 percent. Nevertheless, the grade worsens as the depletant provides the force to silica particles as well as target malachite particles.

Jan 1, 2016

By J. Beland

The Rimouski-Matapedia region is along the southwestern extension of the central Siluro-Devonian synclinorium of Gaspe Peninsula. As in Gaspe about 30,000 feet of Siluro-Devonian strata rest on a "basement" of tightly folded Ordovician rocks. The central synclinorium is divided up into two northeasterly trending belts each of which is characterized by distinctive lithologies and patterns of folding. The northwestern belt is gently to moderately folded and includes lithologies which point to a stable environment. The southeastern belt on the other hand is tightly folded and the lithologies indicate a less stable environment. A marked angular unconformity separates the basement from the Siluro-Devonian cover near the north-western margin of the northwestern belt. At the southeastern margin of the southeastern belt the relationship of cover to basement has not been as-certained because of a fault. The northwestern belt has several features significant in the search for petroleum; the Silurian strata are exposed in broad open anticlines

Jan 1, 1962

By R. E. Eyre, L. P. Landucci

C URRENT practice in the zinc concentrate roasting plant of The Consolidated Mining arid Smelting Company of Canada Limited, at Trail, B.C., involves passing the furnace effluent gases through an electrostatic precipitator for the recovery of dust. After removal of the dust the gas is treated for recovery of sulphur dioxide by conversion into sulphuric acid ( 1). However. as roasting techniques improved, and furnace productivity in-creased, the rated capacity of the precipitator was exceeded and it was necessary to consider various means of improving the dust recovery. A study of methods indicated that a baghouse using silicone-treated glass fabric, might be suitable for this particular application. Glass fabric was chosen because the temperature of the roaster effluent gases would range from 450°F to 500°F and tempering air was undesirable to avoid dilution of the sulphur dioxide gas.

Jan 1, 1962

By F. Bélanger, P. Fournier

"The Detour Lake Mine is located in northeastern, Ontario, approximately 300 kilometres northeast of Timmins and 185 kilometres by road northeast of Cochrane. The mill processes a free milling gold ore using both gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 60,000 mtpd at 95 microns with the addition of pre-crushing upstream of the SAG mill. This paper will highlight the impact of a pre-detox thickener on the cyanide consumption in a gold leach/CIP circuit. While the pre-detox thickener was built with the intention to reduce the cyanide consumption, the opposite effect was observed when the thickener was put temporarily offline. It will show how the re-circulation of a dilute stream of cyanide into the grinding circuit, increases the overall slurry temperature and by the same effect, increases the dissolved copper concentration in the leaching circuit which subsequently increases the cyanide consumption.INTRODUCTION The processing plant is using a conventional gravity, cyanidation and carbon-in-pulp processing facility currently operating at approximately 60,000 mtpd. The comminution process is based on two parallel SABC lines, each fed from an individual reclaim tunnel. Cyclone overflow from the two ball mill circuits is directed to the pre-leach thickener. The thickener underflow is distributed to two (4) parallel leach trains of 5 tanks each, each leach train providing 29 hours of leaching retention time. After leaching, the gold in solution is recovered in a carrousel CIP circuit consisting of two (2) parallel leach trains. Tails from each CIP circuit are combined and sent to a pre-detox thickener to recover as much cyanide solution as is economically practical before being diluted and fed to a cyanide destruction system. The detoxified tailings are sent to the Tailing Management Area (TMA) for settling and retention. The excess water from the TMA is reclaimed and recycled back to the processing plant. The pre-detox thickener is designed to thicken the leach tails slurry to 64% solids with the overflow being recycled to the grinding circuit. It is estimated that the pre-detox thickener will recover 60% of the cyanide in the CIP discharge solution. It is also designed to reduce the SO2 consumption by diluting the thickener U/F to 50% solid using the tailing pond reclaim water which has very little cyanide content."

Jan 1, 2019

By A. F. Abd El-Rehim

The behavior of both transient and steady state creep of Al-4.5 wt% Cu and Al-4.5 wt% Cu-0.1 wt% In alloys was investigated using a constant stress where torsional oscillations of different frequencies and shear strain amplitudes were operated at various working temperatures. An augment in both transient and steady state creep rates was observed by increasing both frequency and shear strain amplitude of the applied oscillations. The mean values of the activation energy of both alloys for both creep stages were found to be equal to that quoted for dislocation intersection mechanism.

Jan 1, 2006

By C. Cano

One of the main concerns within the mining industry is to minimize the impact of tailing facilities to the environment and nearby communities. Since the implementation of the first thickened tailings disposal (TTD) methodology at Kidd Creek in 1964, the thickened tailing disposal has been growing alternative disposal technology to mitigate the environmental impacts. Technical investigations on the TTD technology have been studied in detail to counteract the increasing shortage of water resources. One of the benefits observed with TTD is its resistance to potential earthquakes, particularly in zones with high seismic activity (Los Andes). TTD technology optimizes the maximum possible density for the material and generates a negative internal pore pressure in the material due to the surface and sub-surface water evaporation. This internal pore pressure should be enough to resist the pores pressure to which tailings are subject due to an earthquake action. The objective of this study is to verify the Shrinking Limit (SL) of thickened tailings during initial deposition and in the long term and the ability of tailings deposited by TTD would resist liquefaction. Fresh tailings coming from a flotation process of a copper plant concentrator were used. The samples put under cyclical three-dimensional tests associated with maximum credible earthquake magnitude range of 7.0 8.0 to develop a curve for the safety factor v/s depth for dry densities related to the maximum density obtained at the SL. At a dry density of 1.65 t/m3 liquefaction did not occur at any depth. At 90 % of dry density of 1.51 t/m3, liquefaction did not occur at earthquake magnitudes of 7.0 or 7.5 nor at any depth but liquefaction occurred at magnitude 8.0 between 0 m and 14.5 m; below 14.5 m, liquefaction does not occur.

Jan 1, 2007

By G. M. Behrend

"The mining and processing of mineral ores is a very old industry which is steeped in tradition. Rising demand for metals has recently forced the exploitation of lower-grade orebodies which require extensive beneficiation. The high capital expenditures involved, together with market pressures for high-quality concentrates and pellets, have forced the development of new process technologies which are heavily dependent on automatic process control. Development of suitable instrumentation has been rapid and it is being applied to mining processes today with a high degree of sophistication. The drive for higher efficiency and profitability goes on and has reached a level at which modern digital computers appear to be the only answer. However, the efficient application of a digital process computer is extremely complicated and is therefore approached by the mining industry with considerable hesitation.Some of the benefits promised by the digital computer can be obtained today by other means, which are more manageable and can provide immediate payoff. The result would be a building-block system which would utilize the digital process computer as its final component, to perform true plant optimization, free from routine chores."

Jan 1, 1971

By T. Bednarski, T. McCallum, L. Moya, L. Nsenga, B. Mbao

The accumulation of solids in solvent extraction (SX) circuits can cause problems with the physical and economic performance of the operation. These solids are responsible for the formation of crud, a solid stabilized emulsion containing organic, aqueous, air, and fine solid particles. The build-up of crud in SX settlers can limit SX operation throughput, require plant downtime, lead to higher organic losses, or result in higher aqueous in organic entrainment (all of which can have a significant, negative economic impact). Current practices for crud management are typically reactive. Crud is physically removed after it has been allowed to build to excessive levels in the circuit and processed mechanically using centrifuges or filtration. A new proactive solution has been developed to prevent crud formation and build-up. Low ppm dosage of an additive, ACORGA® CR60, into the pregnant leach solution (PLS) has resulted in reduced crud formation in pilot and commercial scale for a variety of PLS streams. This paper will review results from operations in North America and Africa, covering heap leach, concentrate leach, and agitated leach feeds. INTRODUCTION Crud formation and build-up in solvent extraction (SX) circuits has been a long time topic discussed and claimed to be crucial to the whole hydrometallurgical process (Liu, et al, 2006). Crud formation is present in all SX systems be it copper, uranium, zinc, etc., and Ritcey (1980) defined crud as a stabilized emulsion containing organic, aqueous, and fine solid particles. The ore type and feed composition is a major determining factor of crud formation and typically contains Si, Al, Fe, P, and sulfates (Ritcey, 1980). It typically builds at the interface between the organic and aqueous, but can also be observed as floating crud on the surface of the settler, or bottom crud, which is common to find in circuits treating agitated leach feeds such as in Africa. As crud formation has been unavoidable, many of the current crud management techniques are reactive, allowing crud to form and build in SX circuits. Once it does, it is removed and treated via different mechanical techniques, typically through some type of filtration or three-phase centrifuge, to remove the solids and recover the organic phase trapped within the emulsion (Ritcey, 1980). Automated pumping systems have also been designed and are frequently used in North American operations. The time and capital required to react to crud formation can be an overwhelming aspect to SX operation.

Jan 1, 2019

By Esau Arinaitwe

The most extensively used methods and approaches for characterizing and selecting frothers for plant application are based on measurements in clean water in the absence of solids and without consideration of physicochemical factors that are known to influence the properties and behavior of practical flotation froths, and hence metallurgical performance. These factors include aquatic chemistry, collectors, modifiers, particle shape and size, and pH. Understanding interactions between these factors and the role and relevance that they play in characterizing frothers and froth zone properties will greatly aid in the frother selection and evaluation process. Such an understanding will also greatly enhance the ability to create frother solutions that are sufficiently robust to plant variability (such as mineralogical, comminution, operational, physical and chemical). This paper reports results of a “systems approach” study designed to probe ways in which physicochemical factors a) influence frothing and bubble size in 2- and 3-phase systems, and b) confound correlation of fundamental measurements with flotation outcome. The concepts and insights gleaned from fundamental frother studies, together with empirical laboratory flotation tests and a thorough understanding of plant needs and challenges were used to develop and implement customized frother formulation at a Cu-Mo flotation plant. Plant metallurgical data and qualitative assessment of froth zone properties showed that a frother formulation developed using the approach described here provided marked improvements in froth characteristics (mineralization, mobility, stability, persistence). These improvements resulted in better circuit control and significant performance advantages, such as improved coarse particle recovery, without detrimental downstream effects. INTRODUCTION Successful recovery of value minerals of sufficient grade via the flotation process requires selective manipulation of the value minerals to render them hydrophobic using collectors and modifiers. The hydrophobized minerals then attach to air bubbles and the mineral-bubble aggregates are selectively transported through the froth zone into the launder. Frothers play a critical role in froth formation and more importantly in achieving and maintaining desirable froth characteristics (for example, stability, mobility, persistence) that are essential in facilitating the selective transport and recovery of value minerals. Fundamentally, frothers contribute to the transient stability of thin liquid films and so aid in reducing bubble coalescence rates in the pulp and froth zones, thus maintaining the small bubbles required for efficient bubble-particle attachment. Invariably, the action of frothers at the liquid/gas interface in the pulp and froth zones impacts bubble stability, water and solids transport to the froth, which in turn impacts froth mobility, froth carrying capacity, and the concentrate grade. Consequently, selection and evaluation of frothers for flotation plants requires careful consideration of the frother type, though the choice is limited to only two main classes of compounds in terms of fundamental chemistry (short chain alcohols and polyglycols). Even with the selection of what is thought to be the best frother for a given application, practical knowledge of the froth zone and experience in controlling its properties is essential for maximizing metallurgical performance.

Jan 1, 2019

By E. Herrera, L. Mariscal

"Ilo Copper Smelter operates since 2007 with an ISASMELTTM furnace as a single smelting unit (1,200,000 tpy) associated with two Rotary Holding Furnaces for separation of matte and slag, and which directly produces a discard slag. Southern Peru continually has been improving the slag chemistry of its ISASMELTTM furnace in order to reduce copper losses, given its big economic impact due to large slag mass generation. The present paper describes the influence of the CaO, Al2O3 and magnetite content in the slag of the ISASMELTTM furnace correlated with the SiO2/Fe ratio and its liquidus slag. Also it defines the best slag chemistry and operating practice in order to reduce the copper losses without compromise the bricks life of the furnace.INTRODUCTIONIlo Copper Smelter of Southern Peru (Grupo Mexico) is located on the southern coast of Peru, and treats mainly copper concentrates produced in its own mines (Toquepala and Cuajone).The modernized smelter was commissioned in 2007 and operates with an ISASMELT™ furnace as a single smelting unit (1,200,000 tpy), which is associated with two Rotary Holding Furnaces (RHF) for separation of matte and slag. This slag is directly sent to the dump. Figure 1 shows the smelter flow diagram.The ISASMELT™ process is a bath-smelting process using a single lance. The lance tip is immersed into a molten slag bath contained within the stationary, vertical, refractory-lined ISASMELT™ furnace. The injection of oxygen-enriched air, through the lance into the slag results in a highly turbulent molten bath. Feed material falling into the turbulent bath from above reacts rapidly, resulting in extremely high productivity for a relatively small bath volume."

Jan 1, 2012

By P. J. Oakley, W. M. Thomas, S. W. Kallee, D. G. Staines

A Friction stir welding (FSW) is now extensively used in aluminium industries for joining and material processing applications. The (FSW) technology has gained increasing interest and importance since its invention at TWI almost 15 years ago. The basic principle, recent applications and the continuing development of the FSW technology are described. The paper will introduce some of the variants of FSW, such as Dual-rotation, Twin-stir(TM), and the Stir-lock(TM) technique.

Jan 1, 2006

Particles for heap leaching in conventional circuits are prepared using Cone crushers. Cone crushers are used to crush the ore to the size range between 12-25 mm for heap leaching operations. Leaching from these relatively coarse particles occurs only at the surface and in subsurface regions, which are accessible from the surface by cracks and pores. Since leaching is active in accessible areas, the method of comminution that forms multiple cracks and pores would offer an advantage for heap leach. An investigation was performed in this study to assess if the HPGR forms more cracks and pores than a Cone crusher. X-ray computed tomography (CT) was used to characterize the degree of cracks and pores formed by these two comminution devices that can be used for heap leaching feed preparation. In order to compare the effect of the comminution method on crack network generation, a bulk sample of the zinc ore was crushed by the HPGR at three different pressure settings (45, 95 and 120 bar), the sample ore was also crushed with a Cone crusher for comparison purposes. Products from the Cone crusher and HPGR experiment were then screened into five size fractions ((-25 +19), (-19+16), (-16+9.5), (-9.5+5), (-5+4.75) mm), Subsamples from the ((-25 +19), (-16+9.5), (-5+4.75) mm) size fractions were analysed. The spatial distribution of the crack network of sphalerite particles was characterized using a highresolution industrial X-ray CT system. This paper describes the use of image analysis techniques including image segmentation, which uses a combination of thresholding and other methods to characterize and quantify crack and mineral dissemination in the sphalerite particles after comminution with the HPGR and Cone crusher. The results are validated with those obtained using traditional techniques such as physical gas (with N2) adsorption, mercury intrusion porosimetry, SEM and QEMSCAN.

Jan 1, 2012

By Jim Hazzard

A numerical investigation is presented to examine fluid flow in fractured rock slopes. In mining geomechanics, different numerical modelling approaches are used to estimate fluid pressures in open pit mines. The most common technique is the Equivalent Porous Medium (EPM) approach in which the fractured rock is assumed to behave as a porous continuum. Depending on the geometry and properties of the problem, this may not always be the best approach. The paper presents a parametric study to examine the effect of fracture spacing, fracture and matrix diffusivity and excavation rate on the fluid behaviour in rock slopes. Based on the model results, guidelines are provided as to when EPM models can be used and when different modelling approaches (e.g., discrete fracture flow) may be necessary.

Jun 1, 2012