Search Documents

By Navid Bahrani

Introduction ? Today?s economic market is motivating underground mining companies to increase development advance rates and enhance their NPVs. ? For example, block cave mining involves development of kilometers of drifts with multiple pillars. ? The cyclic nature of drill and blast, and its inherent tendency to damage the surrounding excavation rock mass and increase support demand often result in poor advance rates ? This has motivated mining companies to replace the conventional drill-and-blast as the main excavation method with alternative methods such as mechanized excavation. ? There is little experience with mechanized or non-explosive excavation methods in hard rock metalliferous underground mining.

Oct 1, 2010

By L. I. Kiss, A. Larouche, V. Dassylva-Raymond

Control of the quenching capacity of the cooling water is of primary importance for maintaining the quality and recovery rate of ingots produced by direct chill casting. Industrially, this can be done using a cylindrical metallic probe undergoing rapid quenching by direct immersion in a reservoir filled with casting water. Such a test rig originally developed at Alcan Arvida Research and development Centre was modified and used to assess the role of key parameters affecting the boiling heat transfer. During the tests, the probe of the instrument undergoes the effects of different heat transfer mechanisms. An experimental study was performed in order to clarify the details of the probe-water heat transfer during rapid quenching. The heat flux along the surface was determined by mathematical modeling using the measured temperature signals, while the corresponding heat transfer regimes like stable and unstable film boiling, nucleate boiling and natural convection were identified by the analysis of high-speed video recordings. Aluminium

Jan 1, 2006

By P. I. Laforest, M. S. Moats

"Antimony in smelted copper anodes has been shown to cause problems in electrorefining including brittleness of starter sheets. In order to improve deposit properties, a study was conducted examining the effect of anode chemistry on cathode ductility and electrolyte chemistry. Two industrial anodes with different molar ratios of As/(Sb+Bi) were used in laboratory electrorefining experiments with commercial electrolyte, and the addition of commercial glue and Avitone. The ductility of 21-hr copper deposits was evaluated by a 180° bend test. X-ray diffraction (XRD) and metallography were performed on unbent specimens to characterize the deposit structure. Increasing the anode As/(Sb+Bi) molar ratio from 0.54 to 3.8 resulted in an increase, on average, from four to eight bends to failure in cathode material produced. Significantly lower concentration of antimony (V) in the electrolyte was detected when operating with the higher molar ratio anode. The presence of (111) and (200) planes was noted in cathode material produced from the higher molar ratio anode suggesting that mixed growth character could be responsible for the observed increase in bend test results. The ductility of the starter sheet materials was improved by a higher anode molar ratio.INTRODUCTIONThe presence of antimony in copper electrorefining electrolyte has been reported to cause problems in cathode production (Hiskey, 2012; Peng, Zheng & Chen, 2012; Wang, Chen, Zhou-Lan & Lian-Sheng, 2006; Wang, Chen, Zhou-Lan, Wang, Xiao & Zhang, 2010; Wang, Chen, Zhou-Lan, Wang, Xiao & Tang, 2011; Wesstrom, 2014). To better understand the impact of antimony, laboratory scale electrorefining experiments were conducted using industrial inputs (anodes, cathodes and electrolyte). The influences of anode chemistry on the valences of antimony and arsenic in the electrolyte were monitored and correlated to physical cathode characteristics, such as a bend test to failure and crystallographic orientation.Commercially, starter sheets are produced by electrorefining impure cast copper anodes onto titanium blanks. The starter sheets are then hung in an electrorefining or electrowinning cell using loops of bent starter sheet material. These loops, in the absence of sufficient ductility, fail resulting in cathodes falling into the electrolysis cells. It is thought that the reduction in ductility can be related to anode composition; in particular, the molar ratio of arsenic to antimony plus bismuth As/(Sb+Bi). It has been stated that maintaining this ratio above 2:1 results in numerous improvements to electrorefining operations (Baltazar, Claessens & Thiriar, 1987; Kamath, Mitra, Radhakrishnan & Shetty, 2003; Krusmark, Young & Faro, 1995; Noguchi, Itoh & Nakamura, 1995; Wenzl, 2008)."

Jan 1, 2016

By L. Kilpinen, K. R. Kay, H. B. Fowler

"FOREWORDThe International Nickel Company of Canada has built four ore concentrating plants since 1950. The fifth and largest is now under construction. In each successive plant, the level and type of instrument control and sophistication of control techniques have increased as experience was gained. The type of control progress is illustrated in Fig. 1.At Frood-Stobie the high degree of instrumentation and the level of control were made possible by the constant evolution of techniques and improved instrument hardware technology. We have established in practice concepts that are sound, although many modifications to instrument sensor types and locations 1-rere often necessary. It is generally true that at other existing Inco mills, it is possible to run ""all manual"" for protracted lengths of time because of operator availability and dependence. The Frood-Stobie Mill is the exception, and it is the degree of reliability of the instrumentation hardware and level of maintenance that has made this possible."

Jan 1, 1971

By D. Sediako

Excessive residual stress in Al engine blocks may result in cylinder distortion which reduces engine operating efficiency. As such, neutron diffraction was used to measure residual strain along the Fe liners and Al, in the hoop, radial and axial orientations with respect to the cylinder axis, at the cylinder interbore region. Residual stresses were subsequently calculated using generalized Hooke's law and related to the microstructure along the cylinder bridge. The results suggest that the residual stresses in the Al interbore region are tensile and increased with depth in the axial direction of the cylinder. The increase in residual stress at the bottom of the cylinder coincides with a finer and more uniform microstructure in this region of the cylinder. The refinement in microstructure at the bottom of the cylinder likely increased alloy strength, thereby decreasing this section's susceptibility to distortion. This study successfully quantified the residual stress profiles in a heat treated engine block and related the stress profiles to an as-cast engine block.

Jan 1, 2011

By L. E. Collins

"In western Canada, many new wells contain a significant fraction of H2S. As well, many older wells become increasingly sour over their operating lifetime. For these reasons, there has been increased demand for linepipe and casing for sour service applications in recent years. This paper will review the metallurgical factors which must be considered in designing steels for such applications. IPSCO’s development of linepipe and casing, and experience in fabricating products to meet test standards specified for sour service applications will be summarized. IntroductionWestern Canada produces the majority of Canada’s domestic crude oil and natural gas. A complex system of pipelines has been built to gather the oil and gas from the fields for transport to refining and/or cleaning operations. The gas carried in these pipelines can be either sweet or sour (i.e. containing no H2S or containing H2S) depending on the nature of the field from which it came. Many new fields contain a significant fraction of H2S and many older fields become more sour as their time in production increases. This uncertainty regarding product condition influences the user’s choice of materials for both casing and pipeline applications.It is well known (Merrick, 1989) that hydrogen induced cracking (HIC) will occur in steel when three conditions exist simultaneously: (1) the presence of H2S gas, (2) moisture, and (3) a susceptible material. Steelmakers can only address the latter of these factors. Development of steels to meet test requirements of sour service has been a major focus of IPSCO’s development work for several years."

Jan 1, 1998

By P. C. Lighthall, D. W. Zandee, W. Shukin

"IntroductionThis chapter deals with the on land disposal and storage of fine tailing in slurry form behind dams. Other types of tailing, such as coarse dry cobbs from magnetic separation of iron ores and other dry materials, have special problems and are not addressed in this paper. The disposal of mine waste is not included, except as such materials may be of value in the construction activities related to tailing disposal.In earlier North American mining, mines were smaller and frequently disposed of their tailing by direct discharge into neighbouring streams or bodies of water. Where that was not practical or not permitted, the solids were collected in tailing ponds and only the effluent liquids were released or decanted. The dams used for these early impoundments were fragile structures and failures were common. With the advent of large, low-grade open pit mines, and increasing awareness of environmental and safety considerations, recently established mines have carefully-designed tailing disposal systems, with wellconstructed dams and attention given to protection of the environment. Older mines are being improved or at least being examined critically with a view to upgrading as necessary to meet the new standards.Modern tailing disposal systems are highly variable and unique to each mine. Tailing pond selection and design is dependent on available topography as also is the design of transport and water reclaim systems. Suitable sites that are at higher elevations than the mills or distant from them may require that the tailings be pumped. Dams, either earth or rock structures built of the most convenient and economic material, are usually a suitable mix of local borrow, mine waste and coarse tailings. The most economic structures are those built mostly of coarse tailing."

Jan 1, 1989

By E. R. Rivenbark

"The coal handling plant represents an investment of about $100 million in coal handling and storage equipment. The coal receiving is done by a continuous ship unloader that can handle ships in the 60 000 T range at Q rate of 1750 /ph. A unique feature in the system is a stacker/reclaimer unit which will work inside a dome storage structure. The coal for the unit will include any low sulphur coal that can be delivered by sea at an economical price blended with New Brunswick high sulphur coal.ThE flue gas scrubber is a wet limestone system capable of 95% SO2 removal. The scrubber will utilize about 150 000 tonnes of limestone per year and will produce commercial grade gypsum by the forced oxidization method.IntroductionWith the need for new generating capacity being required, New Brunswick Power reviewed, in 1985, its options for the next unit. The study indicated that the most attractive option for New Brunswick Power would be a coal-fired unit capable of receiving imported coal at a sea port. The site selection process resulted in three site options being considered.The existing Coleson Cove and Dalhousie sites, and the Belledune site were considered. To meet load distribution needs, it was then decided that the unit had to be located in the northern section of the province, thus eliminating the Coleson Cove site. The Belledune site was selected because it had the capacity to have additional units added where as the Dalhousie site would have only been able to accommodate one unit"

Jan 1, 1994

By John Campbell, William Trahant

"Total Quality Management (TQM) is becoming a reality in the mining industry. Widely adopted in the manufacturing and services industries, TQM has become the operating style of choice in numerous mining companies across the Americas and Australia. Iron Ore Company of Canada, Inco, MSA, Graniterock, Magma Copper, and CRA's Hamersly Iron - all are pioneers of TQM. These companies and others are confronting the challenges of implementing TQM and are managing the changes required of their people and cultures. What these companies are doing, why they are doing it, and how they are successfully managing the changes are the subjects of this paper.Driving the need for change in these organizations are a host of issues, some of which all mining companies are facing. Requirements from customers for ISO 9000 certification is becoming one of the initial motivators for Total Quality Management. These standards, commonly used in manufacturing throughout the European Community (EC), emphasize quality in the processes that create outputs, instead of just the outputs themselves. Iron Ore Company of Canada, for instance, responding to the requirement of one of its customers, British Steel, has become one of the first mining companies to meet the quality standard. Suppliers who meet the standards are highly desirable to customers who are themselves operating under the ISO or their national quality guidelines."

Jan 1, 1995

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"Abstract - The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3 and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

By C. Pichler, J. Antrekowitsch

During the production process of steel and other metals a lot of different by products are generated in high amounts. Some of these residues are recycled to recover valuable metals like zinc, lead, copper and others. Especially the treatment of steel mill dust presents a great challenge. The need for new technologies can be seen in the wide range of available recycling concepts for steel mill dust treatment, however most of them have significant disadvantages. An example is the waelz process, which generates about 650 to 700 kg slag during the treatment of 1000 kg steel mill dust. This so called "waelz slag" must be dumped in the most cases. To avoid a landfilling all generated products must be able to get reused in another application. A so called "Zero Waste Process" can be reached with the "2SDR Process" (Two Step Dust Recycling Process), in which the dust is treated on an liquid iron bath generating cast iron, inert slag and zinc oxide. These products have a further usage and can also be sold. The paper focuses on the process development through trials in lab and technical scale up to planned pilot scales, with an accompanying characterisation of the generated products were done.

Jan 1, 2014

By B. A. McKee, T. Adamcewicz

For a capital expenditure of only $46,000, Caland Ore Company has successfully converted its three dry grinding center peripheral discharge rod mills to dry grinding ball mills. The conversion has resulted in a significant capacity increase, operating cost reductions and in-plant environmental improvements. This paper describes why and how• the conversion was made.

Jan 1, 1972

By Georges Houlachi, Akram Alfantazi, Michael Mahon, Maysam Mohammadi

Corrosion resistance of the lead-based anodes directly influences the purity of the final product in the zinc electrowinning process. The anodic MnO2 layer that is electrodeposited on the anodes during this process can protect the anodes against corrosion. Sand-blasted anodes generate a uniform, adherent and shiny MnO2 layer, which gradually blisters and eventually sloughs off after several weeks. In this study, we attempted to develop a new method to stabilize the MnO2 protective layer on the anodes during the electrowinning process by providing suitable nucleation sites for electrodeposition of this layer. MnO2 particles (P80=40µm) were used as seed material for this purpose. Different techniques of galvanostatic and cyclic voltammetry polarizations, scanning electron microscopy (SEM) and atomic absorption spectroscopy (AAS) were employed to investigate the performances of the MnO2-seeded lead anodes. The experimental results showed that growth of the MnO2 layer is influenced by the MnO2 seed particles on the anode surface. The MnO2 layers electrodeposited on the MnO2-seeded lead anodes were uniform and strongly adherent to the substrate. This layer was more stable than those formed on the PbAg anode without MnO2 seeding. This could provide the anode with a higher level of corrosion protection. Moreover, formation of undesirable MnO2 mud in the electrolyte and the rate of manganese consumption were decreased when the MnO2-seeded lead anodes were polarized. These observations could be attributed to the different properties of the electrodeposited MnO2 layer on this anode in comparison with that formed on the PbAg anode.

Jan 1, 2016

By R. S. Bigelow

Part 1.- Metal Mines Early experiments with mechanical loaders in metal mines were confined largely to machines of the shovelling type and generally air-operated. Although the first application of the scraper to metal mines dates back to 1910, it was not until about twelve years ago that it came to be used extensively. Generally, the scraper gives better results in metal mines than in coal mines, as degradation due to soft bottom and breakage are not factors, but it has a wide range of application and is successfully used in the mining of salt, potash, gypsum, zinc, copper, and a variety of ores, from soft material to hard chunky ore which settles compactly. Today, the scraper has replaced to a large extent the shovelling type of machine in metal mines. Scrapers have offered an inexpensive solution for the mucking problem and are now employed in most mining districts throughout the world. They are operated by labourers of all colours and degrees of skill. Each installation, however, requires individual study on the part of the mine mechanical department to determine the type of scraper, horsepower of hoist, and most economical speed of rope, as well as method of rope rigging. Unfortunately, the scraper has no power to select pay ore from waste and its suitability for use under circumstances which might require sorting of the ore can only be decided by a weighing of the economic factors involved

Jan 1, 1931

By M. R. Coffin

Since the plant startup in 1972, the leaching and jarosite precipitation circuits at the zinc plant of the Kidd Metallurgical Division have been reconfigured several times to improve overall performance, and/or to respond to market conditions. For the most part, the circuit changes have been driven by two market factors: the price of zinc and the price of silver. Until recently, circuit modifications undertaken to improve zinc extraction and recovery came at the expense of silver recovery, and vice versa. In 2004, the plant was modified once again to produce a precious metals-bearing residue, but additional leaching circuits were added to ensure that zinc extraction and recovery did not suffer as a consequence. The development of the zinc plant of the Kidd Metallurgical Division is updated in this paper, with a focus on the recent circuit modifications and associated control strategies that were implemented to maximize zinc and precious metals recoveries, and control the quality of the jarosite residue.

Jan 1, 2006

By E. Brouillette

Difficult operating and mining conditions such as low visibility, difficult roadbeds, fast cycling, small openings, and sharp corners create high demand for LHD manoeuvrability and operator dexterity. Operator experience and patience is especially solicited to fill the bucket rapidly and efficiently and performance can be particularly affected by the skill level of individual operators. Teleoperation and automated loading are viewed as options to improve overall equipment and operation performance in certain mining conditions. Comparative statistical measurements of autoloading performance in different production environments at Noranda demonstrate an increase in bucket filling efficiency and a reduction in filling variance, allowing LHD operation to be more consistent and within manufacturer specifications. Consequential cost savings and productivity increases are demonstrated to be transferable to other mining situations.

May 1, 2003

By W. B. Agocs

"IntroductionWITH THE DISCOVERY of natural radioactivity at the end of the 19th century, and the design of equipment for the detection of this phenomenon, radioactivity surveys bad their inception. Early in the 20th century it was found that almost all rocks are radioactive to a certain degree. This radioactivity is due to the nuclear disintegration of six naturally radioactive elements: potassium, thorium, uranium, rubidium, samarium, and lutecium.The radioactivity of these elements manifests itself by the emission of some concentration of alpha, beta, and gamma 'rays'. Of these, the alpha and beta 'rays' are, respectively, helium atoms and electrons, while the gamma 'rays' are short wave length x-rays generated in the nuclear disintegration by the transformation of mass into energy.The alpha and beta rays, being particles of matter, are stopped ve• easily by material barriers, but gamma rays are extremely penetrating and they will pass through a foot or more of rock or several inches of lead.The radioactivity may be detected by the causing of ionization by the radiation. The radiation detectors may be divided into four classes: ionization chambers, proportion al counters, and Geiger counters, all of which use gas for ionization, and scintillation counters, in which a solid is ionized. The basic principle of all these detectors is the same; the difference lies in the method used to measure the degree of ionization produced by the rays. Currently, the scintillation counter is displacing, the other instruments in radioactivity surveying."

Jan 1, 1955

By Robert B. Parsons

"Draft income tax amendments aimed primarily at certain carve-out arrangements prevalent in the oil and gas industry could have devastating results for long standing royally arrangements in the mining industry . Whether or not this potentially damaging effect is intended is largely beside the points-the point is that the mining industry would be well advised to become familiar with the draft amendments and make sure that the potential damage to existing and future royalty agreements is minimized.The draft amendments fail to take into account the nature of mineral royalties and app ear to reflect a lack of understanding of the characteristics of the mining industry.IntroductionOn July 19, 1985 Finance Minister Michael Wilson released draft amendments to the Income Tax Act which are intended 10 effectively thwart the use of so called “carve-out arrangements"".Unfortunately, the proposed amendments are so broad and far- reaching that countless ""innocent"" royalty arrangements in the mining industry, and in the oil and gas industry, are threatened. The potential harshness of the new rules would be compounded by the retroactive application to the amendments to longstanding royalty and similar agreements."

Jan 1, 1985

By R. R. Song, Q. Li, H. Xing, X. C. Wei

Geomechanical modelling of fault stability is an important part of CO2 capture and storage (CCS) research program to ensure its viability and long-term safety. Storage of CO2 in deep subsurface reservoirs requires estimates of sustainable fluid pressures that will not induce fracturing or fault reactivation which could cause fault slip. More importantly, fault slip gives rise to seismic waves, which inflict severe damage to the cap rock of the reservoirs and may result in leakage pathways for the buoyant plume and thus compromise the integrity of seal formations. In this study, we generated a numerical model tuned towards conditions usually encountered in the Shenhua CCS demonstration project in Ordos basin. In particular, with the purpose of evaluating the sensitivity of the parameters as well as their relationships with the moment magnitude of the seismicity, a variance-based sensitivity analysis was adopted for importance ranking of the uncertain input parameters of the given model. However, such flow models could involve one or several spatial inputs, for instance, fault dip, distance between fault and the injection well, friction angle of fault, permeability of fault, Young's Modulus of fault, injecting pore pressure and the stress field. Studying the sensitivity to each of these spatial inputs motivated the present work. The results led to the following conclusions: fault depth and fault dip significantly affect the behavior of the fault and the fault slip becomes violent with the fault depth increasing and fault dip decreasing. Furthermore, the results indicate that slip time increases with the fault dip decreasing and decreases with permeability of fault increasing. In addition, the calculation of seismic moment and moment magnitude of an earthquake demonstrates that it rises significantly with the decrease of fault dip and the increase of fault depth, and it decreases with the rising stress field. The results show that variations of the only controllable parameter injection pressure do not show great influence to the fault behavior compared with other geological factors, which imply site selection is extremely important for the CCS projects.

Jan 1, 2015