Search Documents

By Jeffrey T. McGinty, Frank M. Wheeler

Plant layout is the arrangement of equipment, process areas, departments, infrastructure, and support facilities. Plant logistics is the flow of parts, people, resources, and information throughout the production process. This chapter: outlines key factors and provides checklists to facilitate layout development; presents risk management approaches to test the logistics and functionality of alternative layouts; and uses real-world examples to illustrate effective simulation modelling to assess plant layouts.

Jan 1, 2015

By M. Razavi

This investigation is part an overall investigation on the effect of sodium silicate on the properties of the mine backfill. The results presented will highlight the effects of binder dosage, sodium silicate concentration, and pulp density on the performance of stabilized sodium silicate-fortified sand pastefill samples. Binders implemented for these experiments consisted of cement, slag, and sodium silicate in various proportions. The binder content varied from 3 to 9 wt% (total dry weight) and sodium silicate concentrations was adjusted at 2 and 4% (total binder weight). Moreover, pulp density was adjusted to values between 80 and 83 wt%. For completion of the aforementioned phase of the study, series of sand pastefill test samples were prepared and cured for 28, 56, or 120 days, in a humidity and temperature controlled room. The specimens were tested for uniaxial compressive strength (UCS). In order to study the effect of sodium silicate on microstructures of stabilized sand pastefill, some MIP tests were conducted on selected samples. The results of this investigation evaluate the use of sodium silicate as a partial replacement of cement in stabilized backfill. The analyses of the results demonstrates that, with an increase in binder content and a decrease in pulp density, the UCS values of sand pastefill samples increase. Further more, the results indicate that increase in addition of sodium silicate does not necessarily result in higher strength minefill.

May 1, 2007

Iron deposits of every major type except laterite occur in Quebec, and form one of the major iron ore resources of the world. The five principal types of ore described are: (1) hematite-goethite masses derived from iron formation through the oxidation and enrichment of iron by natural processes; (2) taconites consisting of fine-grained iron formation; (3) metataconites composed of coarse-grained iron formation; (4) iron and titanium oxide minerals in massive or disseminateed deposits within gabbro and anorthositic rocks; and (5) replacement or contact? metasomatic magnetite deposits associated with complex silicate and skarn mineral assemblages. Most of the ore, although relatively low grade, is easy to concentrate. The physical properties of the ores that affect the choice and efficiency of beneficiation methods are described. The extent to which iron ore from this area can be utilized in the future will depend on the continued use and improvement of highly efficient methods of beneficiation.

Jan 1, 1964

By Zhen Lei

In Alberta, Canada, heavy industrial projects are constructed using a prefabrication approach: spools and pipes are produced in the factory, and are assembled into modules that are transported to the industrial plants for installation by mobile cranes. Planning the onsite mobile crane operations is critical to the project budget and schedule. However, due to the large magnitude of industrial projects, manual heavy lift planning is tedious, and the results are not particularly responsive to site changes. This paper introduces an integrated mobile crane management system developed by PCL Industrial Management Inc., in collaboration with the University of Alberta, which investigates crane location selection and path checking for field module assembly. The project information is stored in a database, and the proposed system retrieves data, performs the calculations, and records the results back to the database; the calculations involve automatically selecting locations for the mobile crane, considering the crane capacity, lifting range and utilization. Lift paths for modules are checked for feasibility based on selected locations, satisfying the site and crane configuration constraints, and crane walking paths are planned if needed. The designed system is tested in an industrial project to validate the effectiveness of the system.

Aug 1, 2013

By Navid Bahrani

The grain-based model (GBM) has resolved the difficulty of matching both the directtension (sc) and unconfined-compressive (st strengths of typical brittle rock by providing a synthetic material that mimics deformable, breakable polygonal grains cemented along their adjoining sides with deformable, breakable interfaces modeled as smooth-joint contacts. In this paper, a GBM utilizing a parallel-bonded base material is calibrated to match both st and sc of Lac du Bonnet granite and then used to simulate a Brazilian test. The Brazilian strength (sB) is slightly overestimated and the failure mode includes ductile post-peak response that is not representative of what occurs in laboratory Brazilian tests. By reducing the grain tensile strength, grain failure occurs during the Brazilian test and a more realistic failure mode that includes brittle post-peak response is obtained. However, the unconfinedcompressive strength of the modified material is too low. Sensitivity analysis on the grain and grainboundary strength properties demonstrates that the grain tensile strength controls the sB/sc ratio. Because the grain strength is controlled by the parallel-bond properties and the lowest achievable st/sc ratio in a parallel-bonded material is ~0.25, it is concluded thatsc, st and sB for a typical brittle rock cannot be matched with a GBM that utilizes a parallel-bonded base material.

Jun 1, 2012

By Graham A. Davis, Michael Samis

The dramatic fluctuation in metal and energy prices in the last few years is causing mining companies to consider alternative analytical methods for mine design and valuation. The goal is to improve insight into unforeseen changes in the economic and project environment and to design projects that take advantage of management's ability to respond to these changes. Such flexibly managed projects will contain value that cannot be measured using traditional engineering economic approaches, further motivating the used of alternative, modern valuation methods. This paper considers the valuation of an uneconomic low-grade resource at an open pit gold mine using two of the most popular modern valuation methods, Dynamic Discounted Cash Flow and Real Options. Our analysis demonstrates that the conventional valuation method may incorrectly represent the value and risk attached to mining this type of resource because it is unable to recognize management's ability to respond to future events in a manner that minimizes losses and exploits advantageous business conditions. The results of this paper highlight the importance of recognizing flexibility and business uncertainty in both mine design and valuation.

Jan 1, 2003

By A. H. Lang

Introduction Tin continues to be as much a strategic metal as it was during the war. This situation is due to the fact that the tin mines in the major producing areas of Malaya and the Netherlands East Indies have not yet reached their pre-war production. Moreover, the world requirements for tin in certain fields, particularly in the food pack industries, are steadily increasing. At present, tin is still under International allocation by the Combined Tin Committee, of which Canada is a member nation. This Committee reviews periodically the availability of refined tin for export from the producing countries and makes allocations of tin to ensure equitable distribution to the consumer countries. In 1947, availability permitted an allocation of only 70 per cent of stated requirements. From 1935 to 1938 the price of tin in New York averaged 49 cents a pound and during the war the price in Canada was controlled under a subsidy programme at levels from 60 to 70 cents per pound. Just recently, this price has been raised to 96 cents. The value of the Canadian production amounts to about half a million dollars annually and the whole of this is obtained as a by-product of the lead-zinc-silver ores of the Sullivan mine in British Columbia. In 1947 Canada's imports of tin were 3,961 long tons valued at over $6,000,000. In addition, tin plate to a value of $8,000,000 was imported from the United States; the tin content of this is estimated to be from 650 to 700 long tons. An increase in domestic production would, therefore, be of great national importance, and the present high price may make the search for and development of tin deposits more attractive than it has been in the past. Although no one can foretell what future prices will be, there is reason to believe that, unless there is a drastic downward revision of production costs, the price will be maintained at present levels for some years. A number of tin occurrences are known in Canada, but none of these have been developed for their tin content alone.

Jan 1, 1948

By A. McLean, Q. R. Yang, Y. D. Yang, G. F. Zhang, P. Wu

A considerable amount of waste slag from the pyrite roasting process is discharged every year. Recovery of iron from the waste slag is of great interest for comprehensive use of mineral resource, reduction of environment impact and improvement of economical benefit to related companies. The objectives of the present work are focused on: (1) Compare various procedures for recovery of iron from the waste slag and select a best procedure for industrial trial which is roasting of the waste slag under reducing condition followed by magnetic separation; (2) Investigate the optimum conditions for maximum recovery of iron from the waste slag. The experimental result shows that under the treatment condition found in this work about 36 to 40% of the iron oxide was recovered from the waste slag, where the iron content in the concentrate is 57%. The total recovery ratio of iron, up to 70%, from the waste slag was achieved. After the treatment, sulphur content in the waste slag was reduced significantly and gangue materials, such as SiO2, Al2O3 and TiO2, were reduced effectively.

Jan 1, 2011

By Jamel Sgaoula

During 1998 COGEMA Resources Inc. announced that operations at the Cluff Lake mine will be suspended indefinitely by the end of year 2000 as a result of deteriorating uranium market conditions. To remain profitable, Cluff Lake mine started an aggressive cost reduction program. A cost reduction team was formed to look for ways to lower production costs. The focus of this team was to screen all areas and to come up with ideas to improve the economy of the mine and ensure the viability of the operations over the remaining three years of operations. Among the areas where significant savings were achieved are: (1) replacement of portion of cement with fly ash in backfill; (2) backfill optimization; and (3) new shotcrete plant installation on site for bulk in-house shotcrete production. This paper details the research work carried out by Cluff Lake mine on these projects and results of its application.

May 1, 2001

By P. Su

Friction stir spot welding of a range of Mg-alloys is investigated (AZ91, AZ31, AM50 and AM60). The peak temperatures during friction stir spot welding of all Mg-alloys are close to their solidus temperatures. Also, the apparent material viscosity of Mg-alloy sheet is lower than that when Al-alloy sheet material is spot welded. This is important since it means that the widths of the stir zones forming during spot welding of Mg-alloy sheet are smaller than those when Al-alloy sheet is welded (when identical welding parameter settings are applied). These lower apparent viscosity values must be taken into account during numerical modeling of the Mg-alloy spot welding process. The efficiency of energy utilization is very low when Mg-alloy sheet is spot welded and is of the same order as that when fabricating Al-alloy sheet. The energy generation contributions of the rotating pin and the tool shoulder are investigated. When the spot welding operation is carried out without the application of a dwell period, the contribution made by the rotating pin vis-à-vis energy generation is around 66%. The contribution made by the tool shoulder increases to about 65% when a dwell period of four seconds is incorporated during the spot welding operation. This increase results from a longer contact time between the tool shoulder and material within the stir zone, The failure load during overlap shear testing increases when the bonded area and the energy input increase during spot welding. Sample failure initiates from unbonded regions and from discontinuities at the edge of the stir zone. The formation tendency of discontinuities is increased when Mg-Alloy sheet is spot welded because of the limited deformation characteristics of the base material at lower temperatures.

Jan 1, 2006

By Pan Zhao, Yan-Nan Wang, Fei-Long Liao, Can Cai, Kai-Song Wu

"What are the basic physical parameters and main geometric parameters that are capable of representing the microscopic characteristics of rock? How can these parameters be used to accurately describe the macroscopic mechanical behavior of rock? With such questions in view, and based on the microcosmic structure analysis of rock slices, this paper presents a rock skeleton-pore structure model, holding that rock's mechanical behavior depends on the properties of rock skeleton materials and the form, size and distribution pattern of pores. According to rock stress and deformation behaviors, and in line with the skeleton-pore structure model, an essential mechanics theory for rock is advanced. The assumption that the skeleton materials are incompressible in volume and an introduction of logarithmic strain, generate the relation between porosity and apparent strain. Then, the notion that positive damage and negative damage are represented in terms of porosity is put forward; threshold value of porosity is derived by the damage threshold value of apparent volume strain; a general damage variable of rock is obtained; eventually, with the skeleton-pore model as the groundwork, a global damage constitutive equation is developed, which, with definite physical significance and material parameters to be easily determined, is convenient to apply. It has been proved that the results calculated with this new equation are well in agreement with experimental results.INTRODUCTIONRock is a form of material that contains pores, cracks and skeletons. Skeletons are composed of particles and cements. Pores or cracks within rock actually undermine the assumption of material continuum in solid mechanics. Hence, grave errors — or even false results — are inevitable if some solid mechanics theory is quoted in the discussion of rock mechanics. Many researchers in the field of rock mechanics have attempted various remedies, but the outcome is far from satisfactory — a mechanics theory for rock, in its true sense, has not been established."

Jan 1, 2015

By Helge B. Wurst, Michael P. Cipold, Jan F. Bachmann, Claus C. Bachmann

"In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink-float analysis. Time, cost and safety aspects of the sink-float method have prompted the search for a new approach for establishing separation performance criteria, especially as performance levels of separator plants can be maximized if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes readily available. The new method to establish washability and associated performance information utilizes at least two measurement technologies concurrently: single energy x-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy x-ray transmission and image processing. The value of the collected data increases considerably if the washability data were additionally available in time to be considered in the control of the process plant. The incorporation of an automated washability monitor gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested with a range of sample with different densities, varying from 1 g/cm³ (coal) to 5 g/cm³ (iron ore).INTRODUCTIONWashability of minerals like coal and iron ore is expressed by a curve or graph showing the results of a series of float-and-sink tests. Several of these curves are drawn to illustrate different conditions or variables, usually on the same axes, thus presenting the information on one sheet of paper. Washability curves are essential not only for the design but also for the operation of preparation plants.In determining the washability analysis, particle density is the underlying feature of all washability curves. Conventionally, the particles are separated into density fractions by immersing them in fluids of a predetermined density followed by skimming of those particles that stay afloat. The particles remaining afloat thus have a density lower than that of the fluid they were subjected to. The particles that remained at the bottom of the fluid container thus had a higher density higher than that of the fluid. By progressively increasing, for example, the density of the fluid and immersing the remaining particles so as to be able to skim the next density fraction, the particles would be fractionated into density groups. The liquids used range from aqueous solutions to organic liquids to suspensions. Unfortunately the liquids used for this separation process are often toxic and expensive. It stands to reason that a new method of determining washability is sought."

Jan 1, 2016

By F. Vagnon, A. M. Ferrero, M. Pirulli, A. Segalini

"The topic of this study is the design of flexible fences to mitigate the risk due to debris flow phenomena by means of theoretical and experimental studies analysed in framework of the Rock Engineering System (RES).The study of the interaction between debris flows and flexible barriers is a major challenge since many different aspects concerning both the slope characteristics and the structure features are involved. Debris flows are often triggered by the mobilization of debris deposits that are generated by rock fall of adjacent rock walls. The rock debris deposits are difficult to be characterized by the physical and mechanical point of view due to their large variability in volume distribution and, moreover, when dealing with high mountains environment, they are also strongly affected by the presence of water at different phases (solid or liquid) depending on the temperature. The debris deposit turns unstable in relation with the geotechnical and environmental features of the areas and the instability evolution in high mountain steep valley is often a debris flow. Debris flow destructive potential is very high and protections are often needed to reduce the debris flow risk.This complexity determines the needs of comprehensive study able to include the global basin dynamic and the environmental conditions. An a-priori analysis of the influence of the different aspects can be useful to focus on the real driving aspects of the problem. Due to the complexity of the system the application of the RES methodology is recommended in order to clearly define the different assumptions needed, their influence on the simulations and a comparison among them.RES allows investigating triggering criteria, flow and depositional processes and interaction of flows with protection fences in a rational way. For this purpose, an interaction matrix is created: it summarizes the key geotechnical parameters that influence debris flows, their interactions and debris/engineering protection opera behaviour. The goal is to quantify the diagonal-off terms to assess the residual risk after barrier construction, using back analysis from real debris flow event and data collection from literature.This methodology is applied to analyze a debris flow event in the Italian Western Alps where numerical analyses are carried on to assess flow characteristics to be used for fence design through the application of an analytical and numerical model developed by the authors (Brighenti et al, 2013). In particular, the velocity and deposition heights have been estimated using the numerical code RASH3D (Pirulli, 2010), which is a single-phase model based on depth-averaged Saint Venant equations. Pathways of different lengths are studied to assess the input data necessary to design the protection barrier and to determine the associated risk. Simulation of the barrier at different places along the valley will also allow to determine optimal barrier location in terms of minimum residual risks by comparing the velocity, the volume and the energy of the debris after the barrier impact.The work will produce a possible design scheme to be adopted in this environment."

Jan 1, 2015

By L. H. Cole

FOR many years Industrial Minerals, or as they were formerly called, 'the Non-Metallic Minerals', compared with the metallics, were considered of only minor importance and as such were given scant attention in the technical press as well as in the public press. Those days are, however, happily passing, and thanks, to an appreciable extent, to the constant endeavour of the Industrial Minerals Section of this Institute, established in the fall of 1932 industrial minerals are now assuming the importance to which they are entitled. The term 'Industrial Minerals', when first adopted in this sense by the Institute, was thought to be original in its application, but it is interesting to note that it had been used many years previously by the Queensland Geological Survey in the following publication: SALT Article 1 in Industrial Minerals by B. DUNSTAN, Chief Government Geologist (Publication No. 268, in Part) Queensland Geological Survey, Department of Mines, Brisbane 1920 In Queensland, however, the term embraced some of the metals as well as the non-metallic minerals proper. The lead furnished by Canada in this matter bore rapid fruit, and already the term 'Industrial Minerals' is widely used, not only throughout Canada but in the United States as well.

Jan 1, 1939

By L. O. Thomas

BROADLY, Yukon is divisible into three physiographic provinces which are extensions of the similar divisions in British Columbia that are there known as the Coastal system, the Interior system, and the Rocky Mountain system. South of Yukon to about the 50th parallel of latitude, the Coastal system consists solely of the Coast range, which, in Yukon, passes behind the St. Elias range and for the remainder of its course constitutes the most easterly portion of the Coastal system. The extension, in Yukon, of the Interior system of plateaus and mountains of British Columbia is commonly referred to as the Yukon plateau, and the extension of the Rocky Mountain system as the Mackenzie Mountains system. The Coast-Range province is largely made up of granitic intrusives; the Mackenzie Mountains province of folded sediments; and the intervening Yukon Plateau province of ancient metamorphic rocks, folded sedimentary rocks, volcanics, and intrusives. Almost the entire area dealt with in this article was subjected to glaciation and, in those parts where its full effect was experienced, the valleys were invaded by vast masses of ice which transported and scattered the stream gravels, with their gold content, so that, even where gold still remains in the old stream channels, it has become so buried under boulder clay and other glacial accumulations that it is, in most places, difficult to find, and, when found, may prove very expensive to mine. Most of the present rivers have done little more than cut new channels in the glacial debris, touching only here and there upon the subjacent rocky floor. The territory in Yukon adjacent to the section of the Alaska highway between Watson and Teslin lakes is for the most part unknown both topographically and geologically. From Teslin to Kluane, the highway travels a fairly well-mapped part of Yukon, but beyond that point, until White river is reached, the geology of the adjacent country has, largely, yet to be determined, particularly on the north side of the highway.

Jan 1, 1943

Although Canadian bentonite is competitive in quality for most uses, it has not been accepted for the pelletizing of iron ore concentrates. In 1962, Canada consumed about 10,000 tons of imported bentonite for this use. By the end of 1965, the planned domestic consumption for this purpose alone will probably be more than 100,000 tons a year, valued at about $3 million. Consequently, a challenge exists for the establishment of a Canadian source of high-quality bentonite for pelletizing. Such a bentonite would also be suitable for the two other major applications -well drilling and foundry use. Brief mention is made of such topics as the identification, 1noperties, occurrences, exploration, applications, technology and laboratory testing of this clay. In particular, the type of bentonite in demand, the geological horizons warranting exploration, and simple preliminary test methods are discussed.

Jan 1, 1964

By B. D. H. Knights, N. B. du Preez

The recovery of the economy of the Democratic Republic of Congo has allowed for the rapid increase in production of copper from this region, while the increased price of cobalt continues to support the recovery of that country’s economy. This has enabled the modernization of the process technology used, particularly the change from direct electrowinning of copper to solvent extraction-electrowinning. With this change has come a variety of technical challenges in optimizing the recovery of cobalt from these sources. In this paper, we discuss aspects of the flowsheets for the production of cobalt from the ores of the DRC and Zambia, highlighting the technological improvements that have been made. Following this description of the practice, we assess the challenges of further improving the recovery and purity of cobalt from these sources. INTRODUCTION The African Copperbelt (Figure 1) is by far the biggest producer and holds the greatest reserves of cobalt (Sheed, 2015). However, the ores of this great mining region are extracted primarily for their copper content, and cobalt is a by-product. The ratio of copper-to-cobalt is between 6 and 20 to 1, with the ores from the DRC richer in cobalt than those from Zambia. The overall supply of cobalt, shown in Figure 2, is increasing due to an increase in demand for its use as a battery material. Cobalt is used in superalloys, hard metals, pigments, catalysts magnets, tyre adhesives, lithium-ion rechargeable batteries, and wear-resistant coatings, amongst others. Although these generic categories persist, Figure 3 shows how the relative usage of cobalt is changing due to the uptake of electric vehicles in China and Europe. Cobalt is a key element in lithium-ion batteries, and because it is widely anticipated that electric vehicles will be legislatively encouraged, it is anticipated that the demand for cobalt will rise. This anticipated increase in demand resulted in an increase in the price for cobalt, to which suppliers responded over-eagerly, and the price has dropped dramatically in the first few months of 2019, as shown in Figure 4. However, there is a clear cycle of price peaks in cobalt’s history.

Jan 1, 2019

By Mark Weidenbach

OZ Minerals owns and operates the Prominent Hill copper-gold concentrator in South Australia, built in 2008 and commissioned in early 2009. The concentrator operates via semi autogenous grinding in a thirty four foot ThyssenKrupp Polysius mill followed by a twenty four foot Polysius ball mill in closed circuit with hydro cyclones, designed for an ore throughput of eight million tonnes per annum. The main aspects of designing the circuit are discussed along with the issues faced in the early stages of operation. A review of the optimization strategy applied to the milling circuit such as cyclone optimization, advanced process control strategy implementation and reline management to improve availability is then discussed highlighting areas of significant process improvement that have seen the plant exceed nameplate throughputs above nine million tonnes per annum.

Jan 1, 2012

By Karina Forster

Open stope design depends on the ore body geometry, loading conditions and rock mass properties to estimate stope dilution and ground support requirements. Rock mass conditions for design primarily rely upon estimates of well established rock classification systems. Many sources of data exist for obtaining estimates for these rock mass classification values which include core logging, geotechnical mapping, geological mapping as well as linking one classification system to another through the use of empirically derived equations. The extent of mapping coverage can also vary significantly based on the data collection technique. This paper proposes an approach where individual components of rock mass classification systems are collected by the different available data collection techniques. Data from different rock types are also considered separately based on their alteration characteristics and general observation products. Data from the Cameco Corporation Eagle Point Mine is presented and an approach is outlined for obtaining average representative classification values for stope hanging wall characterization. The effectiveness of this approach is demonstrated through the analysis of a data base of hanging wall dilution information.

Jun 1, 2012

By C. S. Parsons

Introduction Up to the present, the operation of small mills for the treatment of gold ores has not been favoured in Canada to the extent that it has in other countries. For instance, a list of the operating properties in Southern Rhodesia, published in The Rhodesian Mining Journal of November, 1934, shows for the month of September, 1934, that there were over 500 small mills treating less than 50 tons per day, and the majority of these between 5 and 25 tons. They are operated by individuals, syndicates, and small mining companies. It is presumed that the operations are profitable, although from the published figures of the tonnages treated and the yields, it is difficult for one familiar with Canadian operations to understand how this can be possible, in the majority of cases. Most of these small mills employ stamps with plate amalgamation and with, occasionally, tables to produce a concentrate. Enquiries have been received from many parts of the world respecting milling practice suitable for small gold mines and the type of plant used in Canada. The tenor of these enquiries leaves the impression that the majority of the writers assume that the practice would be similar at all small properties. This, of course, is not the case. Conditions vary widely, and what would be a suitable mill for a typical Nova Scotia ore would not necessarily be wholly adaptable to many ores in Ontario, Quebec, or British Columbia. This paper has been written with the intention of inviting discussion, and it is hoped that, by such discussion, the subject will be more fully dealt with than has been possible in the time at the disposal of the writer. Only more or less standard principles and practices have been dealt with, and, purposely, no reference has been made to plants using mills of the Hadsel, the Nutt, or the Gibson type. As there is available but little reliable information on the costs of installation and operation of small mills, it is also hoped that those contributing to the discussion of milling practices for small mines will be in a position to give these data for the benefit of those contemplating the erection of small plants in Canada. Although it is difficult to generalize, it can be said that there are three types of gold mills commonly used at small mines: (1) Amalgamation and Gravity Concentration; (2) Amalgamation and Flotation; and (3) Cyanidation.

Jan 1, 1935