Search Documents

By R. K. Rajamani

Discrete Element Method simulation of charge motion in ball, SAG and autogenous mills has become a standard for design of mill internals, power draft evaluation, etc. Both two-dimensional and three-dimensional codes are being used. The two-dimensional code dominates the user market since the code completes a simulation in one or two hours. On the other hand, three-dimensional codes have been in the domain of specialists who can handle the complexity of the code and have access to parallel computing hardware. For the first time, this barrier is overcome via computing with graphic processing units (GPU). Commodity graphics cards now allow parallel computation with hundreds of processors. It is shown that the computational time has been reduced by a factor of fifty using GPU computing. Hence, SAG charge simulation results in three dimensions are achievable in a few hours using affordable desktop machines. The GPU computing shown here enables the three dimensional simulation into a manageable daily task for mill designers and researchers. On the technical side, the simulations can be elevated to a higher level of complexity to simulate breakage and transport. First, the speedup factor of fifty is established for the Nvidia GeForce GTX 580 graphics card. Next, four simulation tasks, consisting of AG, SAG and ball mills are reported. The simulation of AG and SAG mills are completed in less than 8 hours. The ball mill simulation with 1.25 million spheres is completed in 27 hours. In the near future, as the graphic card hardware advances the compute time can be halved.

Jan 1, 2012

By W. A. Padgham, J. A. Brophy

About 85 % of the 350 tonnes of gold produced by 25 mines in the onhwe t Territories (NWT) since 1935 has come from the Yellowknife-area mines, Con and Giant , which exploit shear zones in Archean mafic volcanic of the Slave Structural Province. Four percent of the total production has been from Archean iron formation-hosted depo its, mainly from Lupin Mine, which today produces more gold than Con and Giant combined and has been primarily responsible for the increase of WT gold output from 5 to 12 tonne per year since 1981. The remaining gold ha been won from the following deposit typesall but the last being in Archean rock : sedimentary-volcanic contact depo its uch a Discovery and Salmita (10 %); turbidite-hosted quartz-vein depo its uch a Camlaren and Ptarmigan (1%); Proterozoic deposits such as Shear Lake and Fox (1#) . All but I% of WT gold has come from the Archean Slave Structural Pro ince, which is also the premiere exploration area for gold deposit types that have yet to be productive in the NWT. These types include stratabound gold in mafic and in felsic volcanic rocks (eg. , at Indin Lake and Courageous Lake, respectively) as well as gold in plutonic rocks (eg. Anialik Gnei Complex). Deposits similar to those in the Slave have al o been found in the Archean Ennadai Belt of the Churchill Structural Province. In the Cordillera. there is potential for placer gold and for gold associated with Cretaceou intrusions.

Jan 1, 1986

By Alireza Golabchi

The AEC (Architecture, Engineering, Construction) industry is an information intensive industry and all related processes employed during different phases of a project, including planning, designing, building, manufacturing, occupying, and maintenance, involve vast amounts of data that is used for a wide variety of purposes. Building Information Modeling (BIM) is a powerful shared knowledge resource which stores this data to support decision making about a facility through all these different phases in its life cycle. Nowadays, BIM is mostly used in the design and construction phases while it can also be highly beneficial beyond those stages. For example, in the Operation and Maintenance (O&M) phase, BIM could be used for automated facilities management or robotic inspection to provide semantic knowledge for navigation. For any implementation not related to the original intent of the BIM (design), organizations need to be able to represent their project data in a common interpretable form, which provides the possibility of an accurate exchange of data among different software products and platforms, known as interoperability. This study has investigated the current state of interoperability between software products used as Building Information Modeling tools. The main focus has been on a popularly used format for BIM models, Industry Foundation Classes (IFC), since it has been specifically developed to enable standardized data exchange. The research methodology involved a comprehensive literature review and the gathering of all fragmented prior research related to the field in order to develop a consistent understanding of the current state of knowledge. This was accompanied with a detailed case study that evaluated and compared two dominant pieces of BIM software, Revit and Bentley, and examined their interoperability strengths and weaknesses while using the IFC format.

Aug 1, 2013

By H. C. Rickaby

The Bannockburn gold area covers the four townships of Bannockburn, Argyle, Hincks, and Montrose, lying in the western part of the Matachewan district of Ontario (see Figure 1). The geology of these four town-ships was studied by H. C. Cooke of the Geological Survey, in 1917-18, and is shown in his map of the district. In the fall of 1930, a rich gold-bearing quartz vein was discovered in the northwest part of Bannockburn by B. S. Ashley. A prospecting rush followed the discovery; many claims were staked in the Bannockburn area, and, during the summer of 1931, a considerable amount of prospecting was done.

Jan 1, 1932

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies.REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows:"

Jan 1, 2018

By Minerals Refining Company, Gerald Luttrell, Biao Li, Robert Bratton, Roe-Hoan Yoon, Stan Suboleski, Nikhil Gupta

Flotation is regarded as the best available method of upgrading coal and mineral fines in the mining industry. However, its efficiency deteriorates rapidly with decreasing particle size. Furthermore, ultrafine concentrates are difficult to be dewatered economically. Due to these technological problems, some operators are forced to discard at least part of the ultrafine materials to tailings (or refuse) ponds, causing significant losses of valuable resources and creating environmental concerns. To address these technological issues, a new separation process named hydrophobic-hydrophilic separation has been developed on the basis of the recent advances in the science of hydrophobic interactions. The results obtained to date show that the process can recover and dewater ultrafine particles simultaneously with high separation efficiencies. Following a series of extensive laboratory tests, the process has been scaled up to proof-of-concept and pilot-scale continuous tests. The results obtained with desliming cyclone overflows, screenbowl effluents, and by-zero coal flotation feeds can be cleaned to less than 4% ash and moisture with over 97% organic matter (or coal) recoveries. The results obtained with mineral fines also showed encouraging results.

Jan 1, 2016

By J. Baumbach, H. Bombach, M. Stelter

"Today technical electro-refining processes for copper exclusively use sulfuric acid, for silver refining nitric acid electrolytes are used. Sulfuric acid is characterized by very good chemical and electrochemical stability, good conductivity and low cost. The disadvantages of sulfuric acid are the precipitation of fine-grained cathodes with smooth surfaces only by using additives like glue, thiourea and chloride. In case of silver the electrolyte is electrochemical unstable and bears the risk of the formation of toxic NOx when pH is too low. A second disadvantage is the form of electrodeposition of silver as dendrites with their removal from the bottom of the Möbius cells.This paper reports the results concerning the application of an alternative electrolyte in copper and silver electro-refining. At first the electrolyte was characterized by the determination of current density potential curves. Electrolysis experiments were performed in laboratory scale using technical anodes for copper and synthetic anodes for silver. During the copper tests the solubility of contaminations from the anodes and the amount and chemical composition of the anode slimes were determined. Moreover the influence of current density, electrolyte temperature and the effect of several additives on the precipitation and chemical purity of the cathodes were investigated. In all experiments cell voltage as well as anodic and cathodic polarization was measured and current efficiency and specific energy consumption were calculated. A comparison with the results with those of tests using conventional sulfuric acid electrolyte shows the advantages and disadvantages of both systems, additionally the technical application chances and limitations for the new electrolyte. This electrolyte enables the precipitation of smooth copper cathodes with low silver and sulfur concentrations even at lower temperatures without any additive. For silver refining the electrodeposition of compact silver sheets is possible, that can be stripped comparable to those in copper electro-refining."

Jan 1, 2016

By J. E. Dutrizac, J. B. Sunstrum

Until relatively recent times, virtually all gold was recovered by gravity and/ or amalgamation methods. Although such techniques are very effective on coarse gold, they become increasingly less useful for finer grains especially when the gold is partly enclosed in rock matrix. Throughout the nineteenth century a number of bonanza gold fields were found in the United States, South Africa, Australia and Canada. In every case the abundant supply of gold nuggets and coarse alluvial gold soon gave way to hard rock mining with its inevitable losses of fine gold in the stamp mill tailings. Continuing efforts to develop new technologies capable of dissolving gold from finely ground ore were eventually successful first with chlorination (the Plattner process) and subsequently with cyanidation. Even before the nineteenth century, however, European chemists such as Scheele and Berthollet were aware that gold could be readily dissolved in an excess of free cyanide(1). As early as 1840, a patent was issued to the Elkington brothers for the dissolution of pure gold in cyanide solution and its subsequent plating onto various metals, with or without an applied electrical current. In 1846, Elsner showed that oxygen was also required to solubilize gold or silver in cyanide media(1). Despite the fact that much work was done on the reaction of cyanide solutions with gold, a viable leaching process for gold ores did not quickly emerge although cyanide solutions were used to enhance amalgamation from the 1860s onward. Major problems were associated with the use of concentrated cyanide solutions; the costs of cyanide were excessive and it was difficult to recover gold from the concentrated media.

Jan 1, 1999

By R. Lodha, C. Oprea, G. Oprea, H. Zargar, T. Troczynski

"The basic refractories used in non-ferrous industry contain chrome ore for improving the thermal shock resistance, thus reducing the penetration of molten metal and fayalite-type slags into the lining. The current study aims to replace chrome ore with Me4+ ions along with Fe3+ ions in order to form MgO-Al2O3- FeOx-Me4+O2 based complex spinel systems that could perform similar to the complex chromia-bearing spinel in the magnesia-chrome refractories. This system allows for lower temperatures of synthesis and sintering. In our study, compositions with 60% MgO were fired below 1500°C and resulted in complete formation of complex spinel, and open porosity less than 5%. The in-situ formation of the complex spinel from the fine mix of oxides in the MgO-Al2O3-FeOx-Me4+O2 system offers a suitable alternative of binding system to produce basic refractories at lower temperatures and of similar physical and mechanical properties with magnesia-chrome bricks fired above 1750ºC. INTRODUCTIONThe synthesis of magnesium aluminate spinel (MgAl2O4) (Maschio, Fabbri, & Fiori, 1988) or magnesium chromate spinel (MgCr2O4) from their respective oxides is diffusion controlled resulting in a sluggish reaction even at high temperatures. For instance, the diffusion of Mg2+ and Al3+ ions in the intermediate spinel layer during reaction is slower than the diffusion of Mg2+ in corundum and Al3+ in periclase. The interfacial layer of spinel formed during the reaction increases the diffusion path for the spinel forming cations. This accompanied by ~8% volume expansion retards further reaction resulting in incomplete spinel forming reaction during sintering and hence densification during the reaction cannot be achieved. In order to assess sintering studies with fine particulate oxides that would result in a lower diffusion path, a mechanical mixture of the hydroxides of aluminium and magnesium calcined at 1400ºC to 1600ºC for 1 hour does not result in complete spinel formation (Sarkar, Das, & Banerjee, 2003), which indicates that reaction sintering of stoichiometric magnesium aluminate spinel is retarded by initial reaction forming the interfacial spinel layer. The basic bricks used as linings in non-ferrous pyro-metallurgical convertors are manufactured using magnesia and chrome ore, the sintering of which produce spinel solid solution. This solid solution is a mix of both normal and inverse spinel structures that sinters at temperatures in excess of 1800ºC in air."

Jan 1, 2012

By Will S. Pettitt

Fracture Network Engineering (FNE) is the engineering design of rock mass disturbance through the use of advanced techniques to model fractured rock masses numerically, and then correlate field observations with simulated fractures generated within the models. Microseismic (MS) monitoring is a standard tool for evaluating the geometry and evolution of the fracture network induced during a hydraulic treatment, principally by source locating MS hypocenters and visualizing these with respect to the treatment volume and infrastructure (Figure 1). The integrated use of Synthetic Rock Mass (SRM) modeling of the hydrofracturing with Enhanced Microseismic Analysis (EMA) provides a feedback loop in which the SRM is constrained by the information provided by the MS data and the in-situ behavior of the fracture network is better understood, leading to informed decisions on future field operations. This paper discusses the technologies used in FNE and some of the developmental challenges we face in order to provide a more efficient and robust application of the approach. One particular challenge is the accurate representation of MS source data within the models (locations, magnitudes and mechanisms), and the ability to correlate these data effectively with field results. This challenge is being overcome by the development of more efficient numerical modeling algorithms, providing simulations in three dimensions at reservoir scale, combined with validation of these algorithms using laboratory and field case studies.

Jun 1, 2012

The dynamic breakage process of rocks by the impact of a hydraulic hammer is more complex than one normally assumes. It is even more difficult when one has to conduct the breakage under water. In such cases one does not know exactly what the surface topography and composition are at the bottom of the sea or river and, hence, it is more difficult to select the best position of the hammer before starting the hammering. Typically, an industrial hammer has a diameter of about 250 mm, a length of about 1.25 to 1.75 m and a mass of several tons. The hammer frequency can be up to 50 impacts per minute. The general principles of rock hammering can be easily summarized, but this knowledge is not sufficient to adapt adequately the method for less common rock conditions (e.g. less brittle rock, presence of vertical and subvertical fractures, etc.). That is the reason why we initiated a research project, whereby a scale model has been developed to conduct experiments in the laboratory and whereby discrete element simulations are being conducted. Both aim at a better understanding of the basic mechanisms of rock hammering. The scaled experimental model allows varying the impact energy and the static weight independently. Within the experiment, the hammer is in contact with the rock specimen under a certain confining pressure and with a certain contact pressure due to the static weight. A weight falls on the hammer, creating the dynamic action or impact; the height over which the weight falls can be varied. The penetration is recorded after each impact. After a certain penetration the test is stopped and the internal crack patterns are described. Some simulations have been conducted, allowing the modeling of individual fracture initiation and growth during the penetration of the hammer by either a constant displacement rate (using the UDEC-code) or by introducing the dynamic process (using the PFC-code). Some of the observed features in the laboratory experiments can be visualized in the simulations. However, further research is needed to allow the simulations being an adequate tool to well understand the dynamic process in laboratory experiments, as well as the in-situ behavior.

Aug 1, 2013

By Y. Duna

The reliability of mine ventilation systems is critical to normal and safe production in a mine and includes reliability of the following parts: ventilation system branch (or passage), ventilation structures, ventilation network, and the fan. Among these, the reliability of a ventilation branch may be considered the foundation of the whole ventilation system. The branch ventilation flow includes four parameters: air volume; toxic and hazardous gas concentrations; temperature, and dust concentration. The calculation model for the reliability of a branch was established based on the analysis of normal distribution of flows in any one branch. Then, the efficiency of the ventilation structures and fire risk compromising the reliability of branch was studied. The results obtained were as follows: if the air volume, toxic and hazardous gas concentrations, temperature and coal dust concentrations of the branch are within reasonable limits, set at any stable state and at the same time, then this branch is reliable.

Aug 1, 2013

By Christopher Boys

"Abstract -Many water inflows in Saskatchewan potash mines are linked to salt anomalies. Potash ore and three anomalies in the PCS Cory potash mine in the Patience Lake Member of the Prairie Evaporite Formation were studied to understand the processes involved in their formation. Another goal was to find geological indicators of the proximity of anomalies. A geological model that relates the potash to the salt anomalies has been developed.Up to five post-burial facies may be recognized . These range from carbonate-mud collapse breccias to bedded sylvinite, and probably result from post-burial leaching. ln this model, the same fluids that caused widespread recrystallization and possibly enrichment of the potash salts, started by dis­ solving huge cavities in the evaporites . The effects of the leaching were highly variable, indicated by selectively preserved delicate laminae and chevron textures, to deformed and totally dissolved salt beds . ln at least two major events, Late Devonian and Cretaceous, collapse structures may have acted as conduits for overlying formation waters to cause pervasive leaching and recrystallization of the Prairie Evaporite Formation .Geological indicators of the proximity of an anomaly may include: a change in Insoluble seam color from greenish-gray to mottled brown and greenish-gray, unusual local increases in ore grade, large patches (e.g., >200 cm2) of sylvite-poor potash crosscutting units near the top of the ore zone, and drops in topography >10 m of the marker seams. Anhydrite was more common in an anomaly than in ore. The local abundance of anhydrite in ore may indicate the proximity of some salt anomalies.Once an anomaly has been encountered, indicators of a major collapse feature may include: stretched clay seams, folded beds, small collapse features (1 m to 20 m), numerous washouts, or split clay seams with injected salt. Any number, or none, of these indicators may be found close to a major collapse feature."

Jan 1, 1993

By S. S. Yuan, Q. Z. Zhu, J. F. Shao

"This paper aims at enriching a homogenization-based anisotropic damage model for hard rocks under complex loading. A new damage criterion is proposed to capture material strain softening. Within the framework of irreversible thermodynamics, we are particularly concerned with two strongly coupled dissipative mechanisms: frictional sliding and damage by microcracking, which usually take place at cracks within cohesive geomaterials under compression. Focusing on the representative elementary volume containing multiple crack families, the free enthalpy of the matrix-cracks system is obtained. Importantly, a back-stress term is involved in the local stress applied to microcracks. This back stress plays the hardening/softening role in the friction criterion which is formulated at local scale. Strain hardening owns to the accumulation of frictional shearing and dilatancy while strain softening is caused by crack growth. The multiscale damage model is used to simulate laboratory tests on the Westerly granite under true triaxial compressions. INTRODUCTIONWhen subjected to compressive loads, hard rocks present nonlinear mechanical behaviors and induced material anisotropies. In that process, two main dissipative mechanisms have been largely identified: damage by crack growth and frictional sliding along closed crack faces, which are usually strongly coupled to each other on crack scale. Theoretical investigations have shown that the damagefriction coupling analyses allow explaining a large number of experimental phenomena involved in brittle or quasi-brittle materials. Concerning constitutive modeling, the standard Eshelby’s solution-based homogenization procedure for heterogeneous materials was recently applied successfully to describing the mechanical and poromechanical behaviors of cracked frictional solids."

Jan 1, 2015

By Chris M. Healey

"Abstract- The Jasper Gold mine in northern Saskatchewan produced a total mill feed of 140 127 tonnes at an average grade of 19.0 g/t Au. Both diamond drilling and chip samples from under­ ground workings returned extremely high values, up to 12 851 g/t (375 oz/I) Au over 0.10 meter from a chip sample. In the presence of such extremely high grades, the accurate estimation of reserves is a major problem.ln the first part of this study, production data from the mine were used to evaluate the results of a variety of reserve estimation techniques in this environment. In two out of three cases studied, indicator kriging with assays cut to 342.9 g/t (10 oz/I) gave extremely good results. In the third case, however , indicator kriging gave unacceptable results. Instead, lognormal kriging of uncut data gave the best results.Secondly, from the same database, a number of drill-hole spacings were simulated, and reserves estimated from the simulations. As may be expected, the results of this analysis show increasingly better results with tighter drill-hole spacing. However, even with a 5 m by 5 m spacing the variation from actual grade was quite large. This is not a systematic under- or over-estimation of grade, rather a random scatter of results .The results of this study show very clearly the problems of deriving good estimates of reserves when extremely high-grade samples are encountered. There is a high degree of randomness to this database, so reserve estimation in this situation will remain a high-risk operation."

Jan 1, 1993

By E. P. Wiechrnann, C. M. Castro, G. A. Vidal, F. A. Muñoz

Different authors and publications indicate that Optibar Segmented Intercell Bars cause a remarkable distortion in the distribution of the current in a cell group. However, these results were based in inaccurate computer based models and do not represent the technology. During the last trimester of 2010, a 92 cells circuit from Barrick Zaldívar EW plant was implemented with Optibar Segmented Intercell Bars. The technology was incorporated progressively without disrupting the plant production. Depending on operational conditions, this led to a 2 to 4% current efficiency increase and 3 to 5% specific energy consumption reduction. By October 2011, 40,000 tons of copper will be produced with the technology.

Jan 1, 2011

By J. C. Allan

THE purpose of this paper is to outline the pogress made in the development o the gravity separation method o ore dressing known as Sink-and-Float, which, in the opinion of the writers, has now reached a stage justifying the claim that this new method marks a highly important advance in the technique . The essential feature of the newest development of this process is the extremely accurate separation achieved. This is responsible for higher extraction in the sink-and-float unit on coarse sizes and, in consequence, for substantially higher overall recoveries. Whilst this is the most remarkable feature of the new process, it has further important contributions to make to ore dressing under the following heads: (1) The introduction of the sink-and-float separator as a buffer helps to iron-out irregularities in the mill feed. By supplying a concentrate of constant grade to the flotation section, the process also indirectly improves overall recovery. (2) The addition of a sink-and-float unit to an existing mill results in substantial increase in capacity at low per ton capital cost. (3) Where the plant can be installed underground for the pre-treatment of low-grade ores, there is a saving in hoisting costs, and excellent 'fill' is provided near the point of use. ( 4) Low-grade mixed oxide-sulphide copper ores may be pre-concentrated, thereby producing a flotation feed sufficiently rich to render the oxide residue from such flotation economic for subsequent treatment by leaching or other methods. (5) Application of the process eliminates hard gangue constituents which cause high grinding costs, or gangue constituents which adversely affect flotation. The plant is compact and easily controlled. No highly skilled operators or expensive reagents are required, and the labour and power per ton are low. The separator is extremely flexible, working equally efficiently on any throughput up to its maximum capacity.

Jan 1, 1940

By B. Caldwell

"The CompanyCardinal River Coals is jointly owned by Luscar Ltd. and the Consolidated Coal Company of Canada (Consol). The Luscar mine is operated by Luscar Ltd. and is located 40 km south of Hinton near Cadomin, Alberta (Fig. 1). The plant sits on the old townsite of Luscar, Alberta, which was founded in order to develop the coal in 1912 (Fig. 2). Initially, the coal was mined by Luscar Ltd. for heating and steam generation and used quite heavily by the railways for their steam locomotives. In 1955, the mine was decommissioned as the demand for coal for tl1ese purposes had dropped off. In 1969, the mine was re-established by Cardinal River to provide metallurgical coking coal for its customers in Japan. The coal is mined from the 13m thick Jewel Seam by open pit methods at a 10 to 1 stripping ratio. The run-of-mine coal is then cleaned to meet customer demands.The PlantThe clean coal preparation facilities at Cardinal River were extended in 1980 in order to increase the feed rate from 450 t/h to 800 t/h. The extension is a separate plant which can be operated on its own or in parallel with the old plant. In addition, modifications have been made to the fine coal circuit (hydrocyclones added), the coarse refuse circuit, (refuse bucks replaced by a refuse conveyor which backfills a pit), and the fine refuse circuit (solid bowl refuse centrifuges, refuse classifying cyclones, and hydra-rake thickener no longer utilized) since the plant was built in 1969. The plant production of 3 M t per year with a yield of 78% is achieved by first screening and breaking the run-of-mine material to a top size of 1 ½ in. The feed is then slurried, sized, and processed in three different washing circuits. The washed coal is mechanically dewatered, thermally dried, and then stored in a 14 500 t capacity silo or on a 300 000 t stockpile. The fine refuse is thickened and pumped to the same pit to which the coarse refuse is being conveyed"

Jan 1, 2000

By Edwin G. Sharp, Frank S. Gaunce, George M. Freeman, Denis J. Kemp, Eric Dulson, Paul Salmon, Ernest R. Hamilton, Carl E. Parden

"THE ECSTALL ZINC PLANT was built for the treatment of the Kidd Creek zinc sulphide concentrates. Construction proceeded throughout 1970-71, with operations beginning in April 1972. The two concentrate types treated differ principally in minor impurity and precious metal contents. Processing flexibility was required to allow efficient recovery of the by-products, especially cadmium, copper and silver. The conversion of the zinc sulphide concentrates to end products follows a sequence of operations that are common to most electrolytic zinc plants and typical of the ""Tainton- Jephson"" flowsheet.1. Roasting in air at an elevated temperature to convert the metal sulphides to soluble metal oxides (calcine) and sulphur dioxide. The sulphur dioxide is converted to sulphuric acid in a contad plant and shipped by train to market.2. Leaching of the calcine in spent electrolyte to effect extraction and recovery of zinc as zinc sulphate solution, leaving an insoluble residue.3. Purification of the clarified zinc sulphate solution by cementation with metallic zinc dust to remove impurities detrimental to the electro-deposition of zinc or detrimental to product purity. The solids from cementation are the starting materials for secondary metal recovery.4. Electrolysis of the purified zinc sulphate solution to reduce the zinc to the metallic state while coincidentally regenerating the sulphuric acid for recycle to the leaching step."

Jan 1, 1974

By Unkown

The Province-wide road ban on movement of heavy loads has had the effect of curtailing or stopping development in several areas. In the Leduc area, the discovery well has been restricted in flow to only a fraction of normal due to limited storage space, but drilling at Imperial Leduc Nos. 2, 3, and 4 has been continued for the past few weeks. The No. 2 well is within 100 feet of the producing horizon and should be completed within the next few days. According to reports, it has been logging slightly lower, structurally, than the discovery well, but, regardless of the outcome, it has been an important test to determine westerly cross-section of the Leduc structure. No official reports have been made available of any tests made during the drilling of the well, but it is understood that promising oil and gas shows have been indicated in higher formations. Actual drilling operations have not been commenced by any of the other companies holding leases in the immediate area but it is expected that, when road bans are removed and equipment is assured, several wells will be commenced. Announcement has been made that Imperial Oil, Limited, will drill a well near Battle lake, about thirty-five miles southwest of the Leduc field. Location of the well has been made following an extensive seismograph survey of the area, with total depth of the test well expected to be in the 8,000- to 8,500-foot range. Drilling will be done with the heavy-duty rig last used at the De Winton test. Imperial Oil have abandoned hope of oil production in the Provost area after drilling nine wells, but will retain their interest in the gas field that has been developed. Of the wells drilled, four indicated gas flows ranging from 1,060 to 13,200 M.c.f. per day.

Jan 1, 1947