Search Documents

By W. van der Merwe

With the gold industry looking to process more complex ores, the online measurement and control of cyanide addition to the gold leaching circuit has become more crucial. This paper compares the two commonly employed "free" cyanide online analysis methods (amperometric and potentiometric end-point silver nitrate titration) with the common site laboratory rhodanine endpoint silver nitrate titration and ion selective electrode methods. Measurement differences between these methods are presented and discussed for cyanide solutions containing copper and zinc with varying cyanide to metal ion ratios. The resulting cyanide available to leach gold is also compared with these measurements.

Jan 1, 2011

By K. N. Bolatbaev, S. S. Naboichenko

The initial rates of dissolution of pyrite, chalcosine, sphalerite and galena in acidic sulphate solutions under oxygen pressure were measured in the range of Poe = 0.2-1 MPa, 130-180 °C, [H2SO4]0 = 0.2-0.7 M, and in the presence of surface-active agents and agitation producing Re = 4-16 x 103. Reaction orders, activation energies, and values of reaction constants for these oxidation reactions were established. The reactions also were shown to be diffusion-controlled; and the rates demonstrate a linear dependence on the surface area of the sulphides. A surface reaction model, in which oxygen is transported through a solid layer of surface products, has been advanced. The initial stage of high-temperature interaction at pH <7 is suggested to involve a chemical activation of the sulphide surface and is described by the following general reaction: MenSm + H3O+ Men-1 Sm-1 (HS-)s + H2O The subsequent oxidation of surface complex HS- to S0 or SO2-4 occurs with the assistance of Fe(III), Cu(II) ions depending on temperature and the redox potential of the medium, which are defined by oxygen pressure and composition of the reaction mixture, especially concentrations of H2SO4 and metals with variable valence. General process kinetics are complicated due to the formation of by-products on the basis of Fe3+ Pb2+, Cup ions, which displace the kinetics into the diffusion region.

Jan 1, 2004

By Marc C. Bétoumay

Workplace safety, health, climatic conditions and rising oil prices are aspects that are important to the mining industry. The need for cleaner energy for underground mine vehicles is requiring serious consideration. A number of alternate energy systems offer clean solutions to diesel emissions while maintaining the current liberty of vehicle movement. This watershed article provides a broad comparison of cleaner diesel and alternative energies for underground production vehicles. Most alternate energies and clean diesel have already been tested in underground production vehicles. There are no technology gaps that would prevent the development of commercial alternative energy power plants, but in the case of alternate energies, second and third generation versions will be required to fully test for safety and operation viability. Full regulatory development is also required and could be done in parallel to power plant testing. Vehicle operation and maintenance manpower would be the same for alternate energy application as for clean diesel. Capital cost for alternate energy power plants will remain higher until the medium term. Owing to significant ventilation savings possible with alternate technologies, operating costs would be reduced.

May 1, 2011

By K. Yoshida

Recently, light magnesium alloy with superior heat radiating ability has been attracting attention in various fields. However cold plastic working of the alloy is very difficult and hot working necessary. Furthermore, the magnesium of products with complicated shapes is difficult, the processing cost is high, and the applicability of the alloy is limited. In this study, a technique for obtaining fine wires and tubes by cold drawing is examined to obtain wires and tubes with high strength, quality and surface morphology, while decreasing production cost. In addition, the shearing strain of magnesium alloy wires and tubes drawn under various drawing conditions was calculated by FEM analysis. It was clarified that cold drawing of magnesium alloy is possible. It was also demonstrated that greater reduction of the cross-sectional area could be realized during cold wire and tube drawing by optimizing the drawing conditions.

Jan 1, 2006

By Michael Bauer

Increases in productivity and improvements in mining occupational safety and health are intrinsically linked. Over the past years, the German Hard Coal Mining Industry has been able to accomplish both: an increase in coal production and, at the same time, a significantly reduction of accidents. This success has been achieved by advances in technology, better organization and investment in people. Since 1990 productivity has more than doubled, while the total number of accidents has been reduced by more than 90%. Further development started initially with the mechanisation of the winning and drivage technology. Innovative technology and standardisation of the mining equipment were one reason for the increase in productivity and reduction of the accident rate. Therefore this technical development was not only one important pillar of the TOM model explicated later but also the requirement for the successful development of the other pillars. In addition to further developing this innovative technology it was possible to realise procedural and organisational improvements. As a result, the above achievement is based on implementing the three pillars of the so-called "TOM" model (technology, organization, ?Mensch? = human). To increase safety, improve performance, raise awareness and change of employees? attitude, the following technical and organizational requirements have been introduced: ??New innovative technology and procedures, standardized techniques and better equipment. ??Measures to revise or redefine the organizational structure, processes and systems of work, which were then integrated into the company policy and procedures as a company management tool. ??Personnel measures (investment in people). These include, improving motivation and behaviour, training, communication to raise and to change awareness of safety issues. Success in Occupational Health and Safety is not an automatic or self-regulating process. It needs hard work to make improvements and it must be treated as a recurring cyclic process. As a result of the above, occupational health and safety has become a natural part of daily work in the German Hard Coal Mining Industry. This could only be achieved by the unconditional "commitment" of all managers and employees to the issues, coupled with discipline and responsible action. Further improvements towards the ultimate aim of "zero" accidents are only possible by mutual involvement in implementing the ?TOM? (technology, organization and ?Mensch? human) model.

Aug 1, 2013

By S. Malkin, Z. Shi, H. Attia, D. Chellan

An experimental investigation is reported on creep-feed grinding of a nickelbased alloy (IN718) using conventional aluminum oxide grinding wheels. Straight surface grinding expe.riments were conducted on nickel-based alloy blocks over a wide range of grinding conditions with straight oil as- grinding fluid applied at high pressure. Grinding power, forces, workpiece surface roughness, and radial wheel wear were measured. Specific material removal rate as high as 64 mm2/s was Used without burning the workpiece, which can be attributed to the extremely low specific energy of 12.6 J/mm3. It was found that the grinding wheel under the present test conditions had a strong capability of self-sharpening as indicated by the stabilized power, forces, and surface roughness after an initial short transient.

Jan 1, 2006

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. In order to clarify the failure mode, fracture surfaces after tensile tests were observed by scanning electron microscopy (SEM). The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles, lamellar structure elongated in the rolling direction contains lamellar boundaries was formed. With increasing the strain, mean spacing of lamellar boundaries decreased. Finally, continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. The tensile strength and hardness of the 6 cycle ARB processed 5083 aluminum alloy sheet increased about two and three times of the initial values, respectively. Results indicated conformity between mechanical evolutions and microstructural changes during ARB process. Fracture surfaces observations showed that failure mode in ARB processed aluminum is shear ductile rupture with elongated small dimples.

Oct 1, 2011

By D. B. Smith

DURING the summer of 1953, test work commenced at the Sullivan Concentrator with a view to the modification of filtration practice by the inclusion of wet cyclone classification of the lead concentrates, with separate filtration of the underflow and overflow products. Formerly, practice was conventional and the equipment employed comprised one 50-foot diameter thickener ?with the underflow routed via a 20-foot stock tank to two 8-foot by 12-foot Oliver filters. Heating of the filter feeds to 40° C. and the use of mechanical slappers on the filter drums ?have both been standard features of Sullivan practice for years. Both of these have been retained. Currently (February, 1956), lead concentrates are being classified into sands and slimes by 12-inch cyclones with the underflow, at 75 per cent solids, being fed to No. 1 Oliver filter. The overflow is thickened to 75 per cent solids and filtered separately by a No. 2 Oliver filter . The tonnage split is approximately two of underflow to one of overflow. The overflow contains 75 to 80 per cent of the total minus I 500 mesh slimes in the feed.

Jan 1, 1956

By Stuart J. Schofield

Introduction The study of the ore deposits of British Columbia is one of fascinating interest not only from a scientific but also from a commercial standpoint and certain wide problems in connection therewith have interested me for some years. Several of these problems have been set forth in papers presented before this Institute on previous occasions. In 1918 it was pointed out that the commercial ore deposits of British Columbia, with one exception, were associated with the granodiorite batholiths of upper Jurassic age. This was followed, in 1922, by a discussion of the ore deposits of British Columbia in which the mineral belts of the province were defined and named, showing a zonal arrangement of ores in which the Pacific coast deposits are characterized by the presence of copper, while the interior belt is marked by the presence of silver, lead, and gold. Methods Of Investigation In reading various reports on the economic geology of British Columbia one is struck with the fact that the mineral veins may be arranged as a system and further examination will show that such a system follows two main directions, one northeasterly and the other northwesterly, both related in origin to the same force.

Jan 1, 1925

By S. Esmaeili

The yield strength model developed by Esmaeili, Lloyd and Poole [1] has been adapted to model isothermal aging in Cu-containing AA6xxx alloys, with (a) a moderate and (b) a very low Cu content in the solution-treated, as-quenched, condition, Isothermal calorimetry has been used to analyze the kinetics of precipitation in these alloys, While the kinetic parameters for the low Cu alloy has been derived from the present experiments, the previously determined kinetic parameters for the high Cu alloy AA6111 has been used to model the precipitation kinetics in the moderate Cu alloy. The age hardening responses of both alloys have been well predicted by the model.

Jan 1, 2005

By M. Zanini, D. Wong

ABSTRACT: Metals market improvements in 2005 drove the desire to increase nickel throughput and the production of nickel oxide sinter at the Vale Ltd. Copper Cliff smelter. Significant difficulties were encountered due to the unreliable quality of Bessemer matte being produced. Concentrate feed changes and the loss of technical and operational expertise during the previous market downturn contributed to the challenge of making the required improvements. Significant progress has been made in the converter aisle by focusing on employee engagement and standardizing best operating practices for a new generation of skimmers. This paper documents these initiatives and seeks to balance the art and science of converting.

Jan 1, 2012

By K. Sugawaral, W. Tongampl, K. Hiruta, Takasaki Y., A. Hosoi, T. Katol, A. Shibayamal

Printed circuit boards of discarded personal computers, televisions, mobile phones and so on contain a significant amount of valuable metals. For the recycle of valuable metals contained in the printed circuit board wastes (P CB W), the effect of temperature on chlorination-volatilization of metals under chlorine gas flow was studied. The experimental sample used was powder of two types: crushed PCBW (Sample 1) made from PC and industrial machines, and crushed-combusted PCBW (Sample 2) made from Sample 1. The principal element in Sample 1 and Sample 2 was copper, about 13 wt% and 20 wt% respectively. Sample 1 was composed of pure metals such as copper, tin and lead. In comparison, Sample 2 consisted of oxide metals such as copper oxide, tin dioxide and silicon dioxide. The two samples were heated at predefined temperatures (ranging from 300 °C to 900 °C) in chlorine gas. The chlorine gas flow into the furnace was set at a rate of 100 mL/min. As a result, copper in Sample 1 began to volatilize at 600 °C and completely vaporized at 700 °C. While in Sample 2, copper started to volatilize at 600 °C and reached 100% vaporization at 800 °C. For Sample 1, zinc finished volatilizing at 500 °C, while for Sample 2, zinc volatilization reached only about 80% (maximum). Also, lead, nickel and titanium showed similar results. Consequently the volatilization rate of Sample 1 is higher than Sample 2 and the temperature dependency was verified for copper, lead, zinc, nickel, antimony, titanium and chromium. In fact, the volatilization rate of these metals increased with the temperature. This result reflects the difference between pure metal and metal oxide, as Sample 2 was combusted before the chlorination-volatilization test. Moreover, the chlorination reaction may be accelerated by a reductive atmosphere because Sample 1 contains carbon. In this study, the volatilization behavior of some valuable metals in PCBW by chlorine gas was observed. Further improvement in the rate of volatilization can be achieved by optimizing the experimental conditions.

Jan 1, 2011

By D. C. Carter

"The Nova Scotia Department of Mines and Energy located a drillhole at Riverside Corner, Hants County, Nova Scotia, to examine the stratigraphy, structure and potash potential of the Kennetcook River gravity low. This evaporite-related gravity anomaly is one of the largest virtually unexplored gravity anomalies in Nova Scotia. The drillhole intersected a structurally complex sequence o flower Windsor Group (&apos;B&apos; Subzone) evaporites. Downhole geophysical wireline logs were used, in conjunction with detailed lithological descriptions, to interpret the structure and stratigraphy of the sequence. Similar application of total gamma ray, density, caliper and neutron-neutron log responses allows stratigraphic correlation of Windsor Group carbonate marker units separated by up to 35 km in Cape Breton. This work confirms the value of downhole geophysical logs as a tool in the exploration of evaporite deposits regardless of the presence or absence of high quality core. INTRODUCTIONThe exploration methodology for evaporite (specifically salt/potash) deposits in eastern Canada (and worldwide) is relatively simple: identify a negative gravity anomaly within a favourable geological setting, Windsor/Cordroy Group sediments in eastern Canada, and drill it (Anderle, 1980). Although this is an obvious oversimplification of the necessary expertise in the planning and complet ion of an exploration program, those familiar with potash exploration drilling can attest to the risks and expense, in terms of time and problems , associated with the location and drilling of diamond-drill wildcat holes. Potash exploration programs in eastern Canada, their results and inherent difficulties, have been documented by Anderle et al. (1979), Cooper (1981), Dekker (1982), Carter and Boehner (1986), Carter (1988) and Carter and Anderle (in prep .).Downhole geophysical wireline logs have become an important tool in the stratigraphic and structural interpretation of evaporite sequences in eastern Canada and, in many cases, represent the only information recovered or the only information available due to the drilling method (rotary) and/or the long term instability of evaporite cores. This paper documents examples of downhole geophysical log responses which, combined with detailed lithological examination of drill core, or in the absence of core, are used in the interpretation of the complex lithology and structure of a deformed evaporite deposit. Geological and geophysical data from the Nova Scotia Department of Mines and Energy (NSDME) Riverside Corner 85-1 drillhole are presented here as a partial case history and prime example of the use of this method to interpret the complex structure of an evaporite deposit. Drilling of NSDME Riverside Comer 85-1 was conducted in late 1985and early 1986by the Department (Carter and Boehner, 1986) under a program to assess the potash potential of selected areas of the province as part of the Canada-Nova Scotia Mineral Development Agreement 1985-89. A reinterpretation of a portion of the available data from two exploration drilling projects on Cape Breton Island in the Canso-Bras d&apos;Or area is also presented (see inset, Fig. I). Several drillholes have intersected the Windsor Group evaporite sequence in these areas and the available geophysical logs are a valuable tool in the interpretation of the structure of the deposits. However, no attempt has been made to present or discuss the detailed geological investigation and comparison of these two deposits. They are presented here as an example of the reinterpretation of existing data and their application to stratigraphic correlation and structural interpretation of complex evaporite deposits. Further work is necessary to document the stratigraphic and structural correlation of these two areas."

Jan 1, 1989

By Q. Han, W. Dai

Al-Ti-B type master alloys have been widely used in the grain refinement of aluminum since 1940s. The introduction of Al3Ti and TiB2(AlB2) particles reduces the grain sizes down to about 200 micrometer level and makes cold work possible. However, the mechanism for the grain refinement is still not clear, though it is believed that TiB2 in the presence of Al3Ti nucleate a-Al grains in solidification. This paper presents our finding on the formation of (Ti,Al)B2 solid solution, which leads to a proposed theory on grain refinement by Al-Ti-B type master alloys that upon addition into aluminum melt stable TiB2 particles react with aluminum slowly and release titanium into the melt. The titanium thus released in combination with titanium in the melt through dissolution of Al3Ti maintains a transient titanium-rich layer on the surface of (Ti,Al)B2. This layer offers a low crystal mismatch with a- Al and promotes the nucleation of aluminum grains.

Jan 1, 2014

By Bradford P. Simser

Increasingly sophisticated rock mechanic tools are becoming more and more available for today?s ground control specialist. However many problems are still beyond our ability to explicitly calculate or measure. There is often a gap between the ?art? and the ?science? of rock mechanics. This paper focuses more on the ?art?, giving relatively simple examples of underground observations and micro-seismic records to help explain ground control issues. Ground support techniques such as in cycle shotcrete with high pressure water scaling, mesh and bolting, pumpable resin bolts/cablebolting, and yielding bolts with load spreading straps are discussed. The use of primary/secondary type blasthole sequences in moderate to high stress situations is also discussed with several examples of the micro-seismic response to the stoping. Relatively erratic geology with high material strength contrasts is currently being mined with blasthole methods at Nickel Rim South. Although the mine is still in its? ?early? days, over 1 million tonnes has been extracted and some empirical experience is highlighted with potential longer term issues also being discussed.

Oct 1, 2010

By X. M. Zhou, T. Wu, He X. N.

"In order to study the support effect of concrete in the surrounding rock of a metal mine, the concrete and surrounding rock were comparatively studied. Firstly, the general situation of the ultra-kilometer deep shaft in Xincheng, surrounding rock and geological conditions are introduced. Secondly, the experimental scheme of material mechanical properties of surrounding rock and shaft lining concrete based on same standard dimension and shape are examined, and the mechanical tests of rock and concrete based on different shapes and sizes are carried out. The study shows that the compressive strength value and elastic modulus of the rock cube are 1.28 times and 1.78 times that of the cylinder, and the Poisson's ratio is 0.77 times. The dimensional effect law of the concrete cube and cylinder test data is consistent with the rock law. However, the test results of the concrete are less discrete than the rock; the test also shows that the strength and elastic modulus of the concrete lining of the main shaft of the Xincheng are much smaller than the surrounding rock that is also used as the concrete aggregate, which indicates that the support of concrete lining in the surrounding rock shaft behaved weakly. Based on the development of the modern NATM rock support theory, it is suggested that the mechanical test standard of artificial support materials should be unified into the mechanics test standard of natural rock, which will help to improve the accuracy and practicality of scientific calculation of geotechnical engineering.INTRODUCTIONConcrete and rock mass are usually attributed to a class of materials called frictional materials or geotechnical materials, of these two kinds of materials, the first is man-maded and the second is natural. The attentive scholar can find that there are many differences in the test criteria for the mechanical properties of the two kinds of materials among different industries or departments, reflecting the differences in their sources, tradition, and the application thoery of material strength among them.There is a situation wordwide, that there are many testing standards of the same material mechanical parameters such as elastic modulus, compressive strength, etc. The cube with a side length of 150 mm is adopted as a common sample in the architecture department in China, while a cylinder with a diameter of 50 mm and a height of 100 mm is as a standard specimen in geotechnical department.Knowing that mechanical parameter values are strongly affected by the the size, shape of specimen and loading rate etc, that is to say the mechanical parameter values of the same material are completely different when obtained from different test with different standards. However, such a problem has been long neglected in geotechnical engineering."

Jan 1, 2019

By B. H. Sadagah

"Construction of mountain roads at north westerly Saudi Arabia is a difficult task in rugged terrains, where the rock masses are steep slopes, and full of geomorphological constraints.Werka descent lies at the north west region of Saudi Arabia. The Werka descent, constructed four years ago harmed due to rainstorm. The rock masses are metabasalt and metaryolite tuff rocks. The road is eight m-wide, surround by unsupported sharp manmade slope cuts, reaches up to 15 to 40 m height on both sides. Failures took place at both sides of the road, and blocked it. The road of almost 2 km long subjected to all modes of slope instability such as rockfalls, manmade slope failures and debris flows in the absence of the remedial measures. The very precipitous 40 m-high rock slope-cut along the road has no benches, backed by a natural slope of almost 80 m height. Both types of slopes suffer from rockfalls and slope failure’s incidents, frequently took place mainly in rainy seasons. The steep manmade rock slope cut is less than 1 m close to the road, with no ditches, form a potentially source area for rockfall’s hazards.Intensive geotechnical study includes utilization of the RMR and GSI rock masses classifications indicates that the rocks are fair to poor quality. The DIPS, RocFall, Swedge, RocTopple, RocPlane computer program, in addition to GIS and DEM image utilized to perform modeling and deterministic analysis, in order to suggest the mitigation measures for the natural and manmade slope cuts and rockfalls. The seismic coefficients of 0.1 to 0.4 taken into consideration in modeling processes. Input parameters to model the rockfalls and slope failure’s characteristics were studied such as GSI, block size; seeder points, locations of fallen blocks; slope angle, restitution coefficients, and slope roughness. The programs modeled the proposed location, height and energy of the rockfall barriers, collectors, and rock bolts. Two manmade slope cuts studied and modeled utilizing the integrated techniques were to eliminate the risk of slope failures and rockfalls through the construction of remedial measures, this is the study objectives."

Jan 1, 2015

By D. Fodor

In Romania, there are significant lignite and brown coal reserves hosted by different regions of the country. The most important lignite bearing zone of the country situated in the North ? West part of Oltenia region and which covers a surface area of 2,500 km2 and host a total reserve of 3.0 billion tons of lignite, of which more than 95% can be exploited by open cast method. The paper deals with the existing geological and mining conditions of the zone , the distribution by mining basins and exploitation perimeters, the open cast working technologies and the economic outcomes obtained throughout the time. Years ago, for the improvement of the economic situation as a whole and in each unit, a large production reorganization, technology update and modernization process was started up. There are described the rehabilitation measures of the technological lines and modernization of the equipments of the production flow-sheet, measures developed at present, too and which will still continue in future. There are mentioned the equipments considered, the components under modernization and the economic outcomes obtained so far. At the end of the paper there are presented the future actions for the equipment modernization and perspectives of the lignite deposit exploitation to meet the national economy requirements of solid fuels.

Aug 1, 2013

Induced microseismicity monitoring is: ?Essential tool in improving the geotechnical understanding about a mine and its inaccessible surrounding rock masses. It helps to determine: -Event timing, location, and magnitude - identification of highly stressed areas -Event source mechanism - the physics of fracturing in its seismic source region -Seismic strain-rate distribution in 5D - identification of stress concentration or migration patterns -Geomechanical interpretation - identification of hidden geological structures or weaknesses in the ground -Strategy for mining e.g. by a block caving method - maximization of mine production and to optimize ground support design -Potential of future seismic hazards -Large event re-entry protocol, to improve mine safety ?The norm as part of mine safety maintenance and long-term mine design practices

Aug 1, 2013

By B. S. W. Buffam

Introduction The development of uranium deposits is a relatively recent phase of mining in Canada. To date, the only producer of uranium ores on a commercial scale has been the Port Radium mine on Great Bear lake, N.W.T. However, with.-in the past few years intensive prospecting has been carried on throughout Canada and many occurrences of uranium-bearing minerals have been discovered. Eldorado has been active in the search for and the exploration of uranium deposits in Canada for a longer period than any other company and has, therefore, accumulated a considerable fund of information, especially about occurrences in Saskatchewan and in the Northwest Territories along the western fringe of the Precambrian Shield. The Company has also had experience in the underground operation, and in the mining, of uranium ores at Port Radium. During the past year or so many requests have been received from the prospecting and mining fraternity for information and guidance regarding the development of the many new uranium discoveries that have been made in Canada. Assistance by Eldorado is freely given whenever possible and this paper is presented to supplement the private discussions and to provide as wide a distribution as possible of the data acquired by Eldorado.

Jan 1, 1951