Search Documents

By Y. Champoux, N. Atalla, R. Oddo, C. Lesage

"Percussion drills are the source of the most serious noise problems in mining activities, due to their extremely high noise levels(114-122 dB(A)) and widespread use(Bartholomae and Stein, 1988). Percussion drills will continue to be widely used to drill small diameter holes in hard rock because no other method seems to be economically avail-able to replace them (Boillat et al., 1993).Many studies (Danière, 1991; Hawkes etal., 1977a; Jensen and Visnapuu, 1972;Leblond et al., 1976; Milette, 1989) were con-ducted to determine the major noise sources of percussion drills. The exhaust air of pneumatic drills, the hammer, the bit in contact with the rock and the drill rod have been identified as the major noise sources. A muffer can be used to reduce the exhaust noise and the hammer can be enclosed. The bit noise is considered to be of concern only at the beginning of holes. When all the available methods are used to reduce the noise of a percussion drill, the drill rod vibrations become the dominant noise source (Hawkes and Burks, 1979). However, the noise levels generated by this source remain high and future efforts should concentrate on reducing its radiation.Works by Hawkes and Burks (1979) and Hawkes et al. (1977b) for the U.S. Bureau of Mines provide the most complete description on the noise and vibration of percussion drill rods.The longitudinal and bending waves are the two most important types of elastic waves generated in drill rods. Among these, only the longitudinal waves contribute to the drilling rate. The bending waves are caused by non-centralized impacts, drill rod curvature and non-uniform bit/rock interface. Drill rod noise is generated by Poisson’s ratio expansions and contractions of the rod as the longitudinal waves travel up and down it and by transverse rod motions induced by bending waves. The radiation efficiency is much higher for bending waves than for longitudinal waves. Most of the impact energy is transformed into longitudinal waves, as expected for axial impacts. The evaluation of the relative contribution of longitudinal and bending waves to noise generation poses a very difficult problem for experimental, analytical and numerical approaches. It is, however, an important issue because the relative contribution of these two waves will guide future noise reduction efforts. It seems that very little can be done to reduce the noise radiation of the axial waves without affecting the drilling rate. The main difficulty that analytical and numerical approach-es face, in the evaluation of the relative contribution of the two waves, is that there is no adequate theory for predicting the bending vibrations from the factors that cause them. The experimental approach has, thus, been limited to test fixtures that do not adequately represent the boundary conditions, as well as by measurements obtained under real operating conditions from which it is difficult to establish the relative contribution of the two types of waves. For example, Hawkes and Burks (1979) and Hawkes et al. (1977b) used a test fixture with free-free boundary conditions and made no clear link with measurement under real operating conditions. Rather, they have based their discussion on a simple model. Many authors assume that fexural waves are the main noise source on drill rods. However, measurements have been somewhat contradictory and researchers are still unable to state with certainty that this is indeed the case (Lednik et al., 1988)."

Jan 1, 1997

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, L. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite by an acid pressure leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project.

Jan 1, 2004

By T. Eger

Load Haul Dump vehicles (LHD) are extensively used in underground mining however equipment design and operating conditions contribute to restricted operator?s visibility. The inability to clearly see people, objects or hazards around the machine has contributed to a number of accidents including fatal injuries. In order to identify vehicle design characteristics resulting in restricted and blocked sightlines visibility assessments are traditionally completed in the field. However, field methods are unable to evaluate visibility under dynamic operating conditions and are limited in their ability to provide feedback on the impact of various operator characteristics such as sitting height, for example. Results of this research show computer simulation and virtual reality can be successfully used to evaluate visibility during the operation of LHD vehicles. In order to benefit from virtual reality applications the work environment, LHD vehicle and human posture need to be represented as accurately as possible. A computer simulation program with ergonomic ana lysis features, Classic JACK 3.1, was successfully used. Threedimensional CAD models of LHD vehicles were developed from manufacturer specifications and pictur es taken from LHD vehicles currently in use. The LHD models were imported into the JACK environment, a digital human was positioned in the cab of the LHD vehicle and the vehicle and human where driven over a typical mine route. Real-time feedback in the JACK program was used to identify what the operator could see under different operating conditions. Machine characteristics and operating scenarios resulting in impaired visibility were successfully identified with this method. The JACK program can also provide real-time feedback on the human?s joint forces and torques, strength requirements, postural comfort, and metabolic energy expenditure. As a result, this method could be used to successfully evaluate musculoskeletal injury risk factors along with system design recommendations to improve workplace safety and productivity in any setting. The LHD VRML files imported into JACK have also been combined with environment files into other VR software packages (e.g. Maverik) to view in a VRL facility, managed by MIRARCO at Laurentian University. The VR models using these packages can be viewed in stereo to provide better appreciation of spatial visibility issues.

May 1, 2003

By G. W. Neumann, J. R. Schnarr

The lead-zinc-copper-silver ores mined by Brunswick Mining and Smelting Corporation Limited at their No. 12 underground mine and No. 6 open-pit operation, and treated by distinct concentration processes in separate plants, present difficult metallurgical problems because of the extremely fine dissemination of the valuable minerals with pyrite and pyrrhotite. The problem of concentration is further complicated, in the No. 12 ore, by the presence of a varying content of graphitic carbon. This paper describes the milling of No. 12 ore and the production of copper, lead and zinc concentrates by differential flotation.

Jan 1, 1971

By J. W. Merkley, K. B. Hustwick

"The authors describe the use of a computer system for the control oj warehouse inventory at Cominco's Canadian operations. The challenge presented by the company's diverse products and various locations necessitated a practical approach to operational and manpower requirements. The utilization of modern forecasting techniques, manual intervention and exception reporting provides system flexibility. The system also provides both operational and management control to set required service goals at the lowest inventory levels for inventory management.IntroductionCominco Ltd. is a Canadian company, with international operations, the principal business of which is zinc, lead and chemical fertilizer s. Its involvement is fully integrated and range s from mineral exploration through mining, smelting, refining and by-product production to international marketing. It also embraces related services, including trade, wharfarge and power. With head office in Vancouver, it is involved, directly or through subsidiary or associated companies, in Canada and in the United States, Greenland, Europe, Australia, India and Japan.Cominco has over 12,000 employees and 26,000 shareholders, with 91% of all shares held in Canada.Cominco's Inventory Control System is one of the most extensively used computer systems employed by the company. Also, inventory control is regarded as one of the most economically successful computer applications to be undertaken by the Data Processing Services (D.P.S) Group that was responsible for the development of the Inventory Control System.The main use of automatic inventory control has been at operating plants in Western Canada and the Northwest Territories, which are separated by large distances. Each location has equipment-intensive mining and processing operations and it is essential to maintain control of parts and supplies inventories. Some of these locations are remote from urban and industrial centres and it is important to avoid the adverse effects of high personnel costs and re-training due to turnover."

Jan 1, 1982

By G. S. Hume

THE discovery of natural gas with naphtha in 1924 in the Upper Palaeozoic limestone of Turner Valley, 35 miles southwest of Calgary, has led to continuous developments in this field. Drilling undertaken soon after this discovery demonstrated that the anticlinal structure was in reality a major drag-fold cut off on the east side by a westerly inclined fault of large displacement. The faulted edge of the .limestone at depth determines the eastern limits of the field, which between 1924 and 1936 was shown to have a gas area 14 miles long by about 1 mile wide. Since the strata dip westerly, away from the axis of the fold, drilling becomes progressively deeper to the west and, with the advent of deeper drilling, crude oil was discovered in 1936 on the west flank of the structure but in the same porous reservoir rocks as the gas on the crest and upper parts of the fold. Since 1936, drilling has been undertaken wholly for the production of crude-oil and at present two producing areas have been found within the Turner Valley structure. The larger of these, at the south end of the field, in the vicinity of Highwood river, has a length of about 4 3/4 miles and a proved width of one mile, whereas the smaller, in the north end of the field, south of the north fork of Sheep river, has only a few producing wells.

Jan 1, 1939

By H. F. Zurbrigg

Introdduction The main line of ascent in the development of the nickel industry may be traced back through the International Nickel Company of Canada, Limited, to its earliest antecedents, the Canadian Copper Company and the Orford Copper Company. Mining geology is but one aspect of the overall development of this organization, and the stress it has placed on geology grew according to the need. In the early days, intensive geology was not required because ore supply was not one of the main problems of this or any of the pioneer companies. The difficulty then was to find economic methods for reducing the ores to nickel and copper, and markets for absorbing nickel in the face of a limited demand from consumers heavily prejudiced in favour of the New Caledonia product. "Very early in the history of the region it was patent to everyone that to share in the full benefits of the industry the same individuals or company must control the whole of the operation necessary to manufacture the finished product' (1, p. 45). These conditions were fulfilled for the International Nickel Company in 1902 when the Canadian Copper Company (incorporated 1886), with its ample ore supply, took the initiative to merge its interests with those of the Orford Copper (Refining) Company (incorporated 1887) to form the new company which, with reorganizational changes, emerged as the producer of the overwhelming bulk of the world's nickel. The Mond Nickel Company, Limited, entered the field in 1899 with a refining process, and over a period of years acquired ore through purchase of mining properties. This Company operated successfully and independently until 1929 when its assets were joined with those of the International Nickel Company in order to permit the most economic exploitation of the Frood-Stobie orebody in which both Companies were interested.

Jan 1, 1948

By P. Duran

The metallurgical gas handling system at Chagres Smelter, like that of many smelters, can be the limiting constraint to processing more concentrate through the smelter. Mass and energy balances for the metallurgical gas handling system processing off-gases from the flash furnace and Peirce-Smith converters have been used by both operations and process engineering groups to help evaluate different operational scenarios in which the use of the installed capacity could be maximized and/or an operational strategy can be change with the purpose of removing a bottleneck or justifying an investment to relieve a constraint in the gas handling system. The present work describes the development of these process balances that were carried out in Exce®. The results were validated with operational data and, subsequently, some cases of industrial interest were simulated, detecting some conditions that were limiting the operation due to the present installed capacity in the Chagres Smelter.

Jan 1, 2007

By R. Kumar, A. K. Verma

"In this paper, an anisotropic shear behavior of rock joints is investigated under constant normal load condition (CNL). The natural rock joint roughness is transferred to artificial rock samples using room temperature vulcanizing (RTV) silicon rubber. Artificial cylindrical rock joint samples (90 mm diameter and 50 mm height) are made by mixture of cement, sand, and water in the ratio of 1:1.5:0.45 (by weight). Direct shear tests are conducted on these samples in twelve directions at 30º apart at four different normal stresses (250kPa, 500kPa, 1000kPa, and 1500kPa). Thus, 48 samples are tested in laboratory. Test results shows that the peak shear strength (?) of rock joints is anisotropic in nature due to change in morphological features in particular shearing direction. Joint roughness coefficient (JRC) is determined in each shearing direction by trial and error method using Barton’s model (1973). Further, cohesion ( c) and angle of friction ( ? )of joint surface in each direction is determined. Finally, a relationship between angle of friction ( ? ) and joint roughness coefficient (JRC) is developed. Experimental shear strength and Barton’s shear strength is compared and it is found that effect of anisotropic decreases with increasing normal stress. INTRODUCTIONRock mass is generally composed of discontinuity which refers collectively to joints, faults, bedding plane and folds etc. ISRM (1978) defined joint as a line of break of geological origin along which there is no visible displacement. Joint is three dimensional discontinuity which composed of two matched/mismatched surfaces. The presence of joints in rock mass plays an important role to define its overall shear strength, deformability behavior, in-situ stresses and hydro-geological properties. The shear strength of rock joints is important in the design of near surface/ deep geotechnical works (mining excavation, dam foundation, power plants, underground caverns, and slopes).In last 40 years, many constitutive models are developed to predict shear strength of rock joints under CNL conditions (Patton 1966; Landanyi and Archambault 1969; Barton 1973; Goodman 1976; Barton and Choubey 1977; Plesha 1987; Desai ad Fishman 1991; Amadei and Saeb 1992; Maksimovic 1992; Wibowo et al. 1993; Huang et al. 1993; Amadei et al. 1998; Indraratna 2000; Homand et al. 2001; Wang et. al. 2003; Samadhiya et. al. 2008; Asadollahi and Tonon 2010; Ghazvinian et al. 2012). These constitutive models have limitations to predict shear strength of rock joints in one direction. Till date, among all constitutive models, Barton (1973) model is widely used in practice due its simplicity. It includes parameters such as joint roughness and joint compressive strength (JCS) to quantify joint surfaces."

Jan 1, 2015

By Malcolm Scoble

Process Technologies Suitable for Application Underground Design Criteria - coarse particle technologies - compact, robust, flexible - waste products suitable for use as backfill Process technologies identified: - Optical/conductivity sorting - Dense media separation - Coarse-particle flotation Process technologies supported by compact & efficient comminution stages Mineralogical evaluation to select process & estimate Performance Further Work U/G Plant Layout & Excavation Modelling Evaluate scenario at increasing depth Establish properties of waste as backfill Model impact of improved backfill quality Evaluate further case studies Evaluate further Environmental Health and Safety Issues Model impact of system development on inventory of national mineral reserves Conclusions Technologies exist for integrated underground mining and processing systems These technologies to be successfully integrated into underground mining system Positive economic and environmental benefits Technical issues to be resolved at depth System Development path identified

May 1, 2004

By W. Dziurzynski, St. Wasilewski, T. Palka, A. Krach

"Air parameter monitoring systems, regardless of gasometrical protections, provide a significant number of measurement data. The obtained data broadens the knowledge on processes taking place in underground workings and shows the relationships and influence of machines and technological processes on the variability of ventilation parameters in the areas of longwalls. Nowadays, computer simulation methods are increasingly used to reproduce the flow of air and methane mixture in the area of longwalls equipped with shearers. The paper presents the results of a research experiment covering a long-term observation of a longwall area during mining with a shearer using sensors from the mine's monitoring system. Data from sensors for methane concentration, pressure and velocity were used and additional ventilation measurements were taken to determine the parameters characterising the air flow in the area. The influence of different machine cycles in the longwall on the changes of air parameters in the area of the longwall was shown. A numerical model of the ventilation area was developed and the computer program VentZroby was used for the calculations, which allows for the simulation of the process of ventilating the area of the active longwall during the extraction of coal with the use of a shearer and haulage of the run-of-mine. Computer simulation of the influence of the shearer's operation and the methane inflow associated with the distribution of the mixture of air and methane was carried out. The results of the simulation were compared with the data recorded by the monitoring system’s sensors during the measurement experiment. Comparison of the recorded methane concentration courses with the results of a computer simulation of the air and methane flow conditions in the mining area showed changes in the gassiness. INTRODUCTION Studies carried out in the Polish and global mining industry show that methane is an obvious factor in limiting mining production due to the loss of continuity in the operation of longwall complexes in hard coal mines under methane emission hazard (Schatzel et al., 2008). In addition, methane hazards have a significant impact on the safety of the operators of machinery in the longwall. The requirements of Polish regulations and the practice of safe operation of mining longwalls require correct determination of gas concentration, volume flow, as well as pressure and temperature of the flowing air. As part of the research undertaken in the Budryk (Wasilewski, 2010) and Bielszowice (Dziurzynski et al., 2009) mines to assess the methane hazard in the longwalls and workings in the vicinity of the longwall, research experiments were carried out, during which air parameters were recorded by the mine monitoring system and additional testing equipment in different cycles of shearer operation."

Jan 1, 2019

By A. Ignatieff

"Excavation, the principal mining process, 'which hitherto has been based largely on the intuition and logic of mining men, is increasingly receiving the attention of engineers and scientists versed in rock mechanics. The paper intro-duce the principles of this science in simplified form, directed both to underground and open-pit mining. Reference is made to the large annual tonnage from ore and rock excavations, which in 1967 were responsible for 250 million tons of mineral production in Canada.The urge to transform excavation into a continuous instead of an interrupted process is discussed with references to the various types of energies employed or proposed in rock breakage or excavation. Due to the rapid decay of applied energy in the discontinuous and heterogeneous rock environment, large confined blasts proposed for in-situ mining do not give much expectation of success as yet. Raises and ventilating shafts are already bored in reasonably hard rock. Tunnelling machines will be used for drifting and cross-cutting in the future, but continuous mining machines of the cuttmg and shearing type are not 'around the corner' for stoping typical orebodies. On the other hand, bed mining, particularly of coal, has led the way in continuous mining, and Remotely Operated Long-wall Face (ROLF) experiments are progressing in an encouraging way. Some reflections on the mining environment in relation to the human element are made."

Jan 1, 1970

By M. Stogran-Baker, E. Legault-Seguin

"Fluorspar mining in the St. Lawrence area of Newfoundland and Labrador began in the 1930s and ended in the mid-1980s. In 2013, Canada Fluorspar (NL) Inc (CFI) discovered a new ore body, the AGS vein, which proved amenable to more economic open pit mining methods and began developing this resource. This paper discusses the flowsheet development of the AGS vein deposit. Testing at SGS began in 2009 with samples from other deposits in the area. The testwork included pilot-scale dense medium separation (DMS), laboratory-scale flotation tests to develop the flowsheet and a flotation pilot plant. The more recent work that is presented here has been devoted to the AGS vein, and included a variability testing program that gave tremendous insight into the metallurgical drivers of processing the deposit. The ore was found to be fairly variable in terms of fluorite grade, but also gangue mineralogy, which had greater implications on the DMS performance. The gangue mineralogy was also found to significantly impact the grindability characteristics of the DMS product. This paper will detail the testing conducted and the mitigating steps which were identified for the operation.INTRODUCTION Fluorspar is the industrial trade name for the mineral fluorite (CaF2), which is the primary industrial source of fluoride. There are a number of categories of fluorspar, most notably acid-grade fluorspar and metallurgical fluorspar (metspar). Acid-grade fluorspar has stringent specifications and is suitable for the production of hydrofluoric acid that is used for many applications. The typical specifications of acid-grade fluorspar are >97% CaF2 and less than 1% each of SiO2 and CaCO3, with a particle size distribution in the order of 80% passing 100 µm. Metspar is typically used for metallurgical purposes, typically as a flux in smelting, and has significantly more relaxed specifications (< 15% SiO2). The principle source of fluorspar in Canada has been from the Burin Peninsula in Newfoundland and Labrador. More than 3 million tonnes of fluorspar were produced there between 1940 and 1978 and from 1987 to 1990, when production ceased (Fulton & Montgomery, 1994)."

Jan 1, 2018

By Simon Weixiao Sun

Conventionally, carbon steel has been the primary material for salt mine headframe construction, protected by specialty paint layers to prevent corrosion. These layers require meticulous QA/QC during fabrication and erection, and the top UV protection layer typically loses effectiveness after an average of 10 years, necessitating ongoing maintenance. As headframes age, significant structural repairs are often required. Alternatively, stainless steel can eliminate corrosion concerns, though its high initial cost has limited its use in headframe design. However, when factoring in long-term maintenance costs, a 'maintenance-free' stainless steel headframe can be an attractive option for stakeholders. This paper compares the structural performance and economic considerations of painted carbon steel and stainless steel headframes, including initial capital and long-term maintenance costs. Additionally, it explores a hybrid approach, strategically using carbon steel in low-contamination areas to reduce initial costs and significantly minimize future maintenance efforts.

May 4, 2025

By John D. Campbell

Alberta Plains coals exhibit an almost rectilinear system of vertical fracturing called "cleat", which is best traced by mapping true bearings of underground coal mine rooms. The cleat pattern is approximately conformable with a pattern of surficial features and a pattern of bedrock jointing in the Alberta Plains, and with the trend of the Rocky Mountain Trench, but not with the distribution pattern of coal rank nor with the trend of the eastern boundary of the Rocky Mountains and Foothills physiographic province. The processes resulting in cleat remain in doubt, but cleat is always of practical importance in extracting coal from deeply buried deposits.

Jan 1, 1979

By G. B. Bosworth, M. J. Lake, J. W. Hogg

The Quintette Coal operation in northeastern British Columbia has one of the world's largest Preparation Plants, with a design capacity of 6.5 million tonnes per year of clean coal.This paper will discuss several innovative aspects of the flowsheet and plant design with particular reference to the selection of process equipment, materials handling and control systems.The operations and maintenance experience during the first two years of production will be described and discussed in relation to the design objectives.

Jan 1, 1987

By W. E. Johnston

At last year&apos;s Annual Meeting a paper by Haultain and Johnston was presented entitled Is the Gold in Tellttrides Soluble in Cyanide? Since then the writer has continued the study of various phases of this problem. Samples and specimens of ore from some of the Kirkland Lake mines have been studied and non gold-bearing tellurides have been found in these that are not soluble in ordinary mill solutions. Samples of tailings, both old and recent, from this district have been examined with apparatus and methods that have proved very successful in detecting the presence of extremely minute quantities of tellurides. Tellurides, both base-metal and gold-bearing, have been discovered in these tailings, but only in such minute quantities that their presence would not affect the ordinary assay results. More free gold particles have been found in the tailings than gold-bearing tellurides. Much experimental work has been done on tellurides, concentrated from high-grade material and from ordinary run-of-mine ore. The gold-bearing tellurides behave very much as does gold itself. Finely divided particles are dissolved fairly rapidly, coarser particles more slowly. All the tellurides are soft and brittle and also have a high specific gravity, with the result that they are extremely finely divided in ordinary mill practice. The ordinary high-lime solution of Kirkland Lake practice is suitable for the dissolving of the gold tellurides. Oxygen is necessary, but apparently not more so than in dissolving gold. Some particles have been found that appear under the microscope to be ordinary metallic gold particles, but on heating they show a small telluride content. These appear to dissolve more slowly than gold. There is considerable variation in the ratio of tellurides to gold from different points in the mines. So far the writer has failed to find any connection between this ratio and the richness of the ore. Generally speaking, the base-metal tellurides predominate. Some of these contain gold but this may be due to a mixture of tellurides in the one particle.

Jan 1, 1933

By V. G. Papangelakis, J. E. Dutrizac, G. Azimi

A new model capable of predicting the solubility of calcium sulphate solid phases in zinc sulphate processing solutions from 25 to 95°C was developed. The model uses the Mixed Solvent Electrolyte (MSE) model of the OLI systems software to calculate the mean activity coefficients of the electrolyte species. The model was tested using recently developed experimental measurements. It was shown to predict accurately the solubility behaviour of calcium sulphate in multi-component zinc processing solutions containing ZnSO4, H2SO4, MgSO4, MnSO4, Fe2(SO4)3, Na2SO4 and (NH4)2SO4. The model can also explain the complex effect of coexisting metal sulphates on the solubility of the CaSO4 phases. The model is a practical tool for assessing the process chemistry of a wide variety of complex aqueous processing streams.

Jan 1, 2008

By J. J. Jonas, G. R. Stewart, A. M. Elwazri

Two important parameters for dynamic recrystallization can be derived from the changes in the strain hardening rate: the critical strain for initiation of dynamic recrystallization and the point of maximum softening. In this work, these values are determined from the flow stress-strain data obtained in continuous compression testing in the range 900-1100°C. The resulting strains are used to calculate a kinetic model of dynamic recrystallization for two materials: 304 austenitic stainless steel and a hypereutectoid plain carbon steel. The mechanical parameters used to define the proposed model are confirmed with quantitative metallographic analysis of the recrystallized microstructure.

Jan 1, 2004

By M. R. Khalesi, S. Bellec, C. Bazin, D. Hodouin

Batch grinding tests conducted on a gold ore indicated that gold is not randomly distributed within the size fractions of the ground ore. Since gold leaching performances were found to be dependent of the size of the gold carrying particles an integrated gold ore grinding-leaching simulator should incorporate a method to predict the gold size distribution of a ground ore. The paper describes the results obtained from batch grinding tests showing the non random distribution of gold within the size intervals of a ground ore and the initial developments of a grinding model to predict the gold size distribution in a batch grinding product.

Jan 1, 2011