Search Documents

Gold recovery from refractory ores can be very difficult and complicated depending on the causes of the refractoriness. Typically, a fine wind and/or the oxidation of the gold-bearing sulfide minerals are required to liberate gold from the host rock matrix. Mineral separation techniques, particularly surface¬wettability based separation (i.e., flotation) and magnetic separation, can be used to pre-concentrate the gold and sulfide minerals, or to remove mineral species that are harmful either to the oxidation of the gold-bearing sulfides or to the cyanidation following the oxidation. In this paper, several processes are described, including oil-agglomeration flotation recovery of fine-grained gold and sulfide, reverse flotation of carbonate minerals prior to pressure or bio oxidation, reverse flotation of elemental sulfur after pressure or bio oxidation but prior to cyanide leaching, and magnetic concentration of gold-bearing iron oxides. The integration of these techniques with gold hydrometallurgical processes may make the economic recovery of gold from an otherwise uneconomic refractory ore possible.

Jan 1, 2011

By Youjun Tao

Falcon centrifugal gravity separation tests were conducted to study desulfurization and de-ashing performance with different size fractions of a high-sulfur Chinese -0.5mm fine coal in a dense medium. Performance indicators such as combustible recovery, ash and sulfur rejection, and desulfurization efficiency were used to evaluate the separation efficiency. The results show that for -0.5 mm coal particles, all performance indicators except ash rejection are higher for the Falcon concentrator than for flotation. More specifically, for the +0.125 mm size fraction, Falcon centrifugal separation produced better ash and sulfur rejection performance than froth flotation. However, the Falcon concentrator also showed higher combustible recovery but lower ash and sulfur rejection than froth flotation for the -0.125 mm size fraction.

Aug 1, 2013

By Floyd Smith

Based on underground observations made in .the coal mines of the Dominion Coal Company Ltd., this paper deals with the stress phenomena in the approach roads and headways and in the gob areas associated with the longwall method of total extraction. The deformation of roadways during development and the deformation of roadways during the total extraction period is delineated and presented in graphical form .. Conclusions are made as to the feasibility of the introduction of the retreat method of longwall extraction in one of the colhenes. The importance of future studies are enumerated, especially. those pertaining to the determination .of the opti.m.um sizes of protective pillars and to increasing the efficiency of the current methods of artificial roadway support.

Jan 1, 1967

By P. Lostritto, G. E. Agar, G. Labonte, M. Cherevaty

"A locked cycle flotation test was done on a sample from the ovoid portion of the Voisey 's Bay copper-nickel sulphide ore. The chemical conditions for this test were generated by prior independent testing. In this test work the time in each of the five separation stages was optimized prior to executing the locked cycle test. A numerical simulation of the continuous circuit material balance was done prior to the locked cycle test. The test results were not fully satisfactory because the flotation of pyrrhotite in the bulk rougher and cleaner stages was not consistent. The preliminary indication was that the samples had oxidized to varying degrees during storage.INTRODUCTIONINCO has performed batch laboratory flotation testing on ore from Voisey's Bay which is a mixture of chalcopyrite, pentlandite and pyrrhotite. Earlier, Lakefield Research was contracted by Diamond Field Resources to test the ""flotability"" of the ore, which included a pilot plant trial. INCO's J. Roy Gordon Research Laboratory has repeated many of the batch tests that Lakefield did to verify their results. Based on their own work, INCO has modified the circuit proposed by Lakefield Research. The modified circuit is based on batch test work, but no locked cycle test (LCT) was done. It is believed that this circuit will produce a copper concentrate at 29-30% copper and a primary nickel concentrate at 15-20% with recoveries of 80% or above.For several years the University of Toronto has been working with INCO to provide ""hands on"" experience for undergraduate students as an Industrial Research Project (IRP). This year, the objective for IRP was to optimize the time for each of the five separation stages for the Voisey's Bay ore then to numerically and experimentally simulate the material balance for a continuous circuit."

Jan 1, 1998

By H. Aaltonen, T. G. Robinson, M. Morimitsu

"The energy required to plate pure zinc can be the most significant operating cost for an operator in the production of electrolytic zinc. This paper reports on developments on low energy Outotec coated titanium anode process technology with fully amorphous coatings, MSA®, and its application to brownfield zinc electrowinning operations around the world. This technology aims to reduce the operating cost and increase productivity for zinc producers.INTRODUCTIONZinc electrowinning is an energy-intensive process using more than 3,000 kWh/t of electric energy [1-4], and the reduction of the energy consumption is one of the key issues. The high energy consumption is due to a high cell voltage during electrolysis, which is mainly caused by a high overpotential of oxygen evolution reaction on lead alloy anodes which have been widely used in commercial zinc electrowinning processes. The overpotential of oxygen evolution is 0.6 V or more and which is approximately 4 times higher on average than that of the cathodic reaction (zinc deposition) [3,4]. Therefore, the reduction of oxygen overpotential is significant to reduce the electric energy consumption, and this will become more significant with increasing demand in metal production and rising energy costs.Oxide coated titanium anodes have been widely investigated for the oxygen evolution anodes in order to replace the lead alloy anodes [5-9], because it is known that the oxygen overpotential strongly depends on the material and structure of the anode. The most typical example of such anodes is an IrO2-Ta2O5 coated titanium anode, which is usually prepared at thermal decomposition of a precursor solution containing metal salts at 450 oC or more and obtained mixed oxide coating consists of crystalline IrO2 and amorphous Ta2O5. On the other hand, one of the authors of this paper, Professor Morimitsu, Doshisha University in Japan, has developed a novel oxide coated titanium anode, MSA® [10-25]. The most specialized point of MSA® is that the catalytic coatings are prepared at low thermal decomposition temperature and amorphous IrO2 or RuO2 is contained as the components in the coatings. Such amorphous coatings have high catalytic activity for oxygen evolution compared to lead alloy or crystalline coatings. Outotec acquired the international specialized MSA® patent licensing rights from Doshisha University and has produced and commercialized the amorphous oxide coated titanium anodes. These anodes have already been utilized mainly in copper electrowinning plants worldwide and have demonstrated a significant voltage reduction, a cost-efficiency, and a long lifetime. This novel technology is also effective to zinc electrowinning process, thus this paper presents the characterization and performance of amorphous IrO2-Ta2O5 coated titanium anodes and amorphous RuO2-Ta2O5 coated titanium anodes for oxygen evolution in zinc electrowinning."

Jan 1, 2016

By P. C. McLeod

THE GECO OREBODY, located north of lake Superior in the Thunder Bay district of northern' Ontario, was discovered in 1953. Diamond drilling in the following year indicated a 15,000,000-ton ore-body, and production plans were made for the shipment of copper and zinc concentrates in three years. To accomplish this, the Geco Project was initiated. The property was in an undevdoped, inaccessible area, and the project involved the conversion and extension of a logging road to the property, the construction of two railways and seventy miles of hydro transmission line, the erection of a municipality, the building of a plant, and the development of an underground mine to produce 3,300 tons per day. This paper describes some of the methods used in the underground development phase of the Geco Project.

Jan 1, 1958

By C. H. Sleeman

"The Iron Ore Company of Canada constructed a beneficiation complex in Sept-Iles, Quebec, to concentrate and pelletize earthy red hematite iron ores from the Knob Lake area. The plants were scheduled for initial production during the first quarter of 1973.Many problems have been experienced to date. Difficulties in controlling the process, excessive mechanical failures, design deficiencies and manpower-staffing problems have caused an extended start-up. The problems are now essentially solved and, with the completion of some additional minor modifications, it is expected that the plants will be producing premium iron ore pellets at or near rated capacity within the next immediate period."

Jan 1, 1976

By M. Normandin

The performance of various polymers and other macromolecules used to flocculate red mud particulate materials in the Bayer process can be evaluated on the basis of their efficiency to achieve adequate settling velocity and turbidity level, The Jar Test is widely used in the mineral industry to determine the efficiency of solid-liquid separation processes, particularly for gravity settler of the Bayer process. However, a high level of variability is found in the data obtained by this methodology, In this study, different parameters of the cylinder test procedure are evaluated to determine their role in the overall variability of the method, As demonstrated by laboratory testing, the overall variability can be considerably reduced by good laboratory practices.

Jan 1, 2005

By Derek Perkins

"Brenda Mines Ltd. operates an open pit copper and molybdenum mine located in south central British Columbia. The main economic mineralization is chalcopyrite and molybdenite. Pyrite, galena and sphalerite are also present in varying quantities. The mineralization is present in small veins and fractures in a porphyritic quartz diorite host rock.The mill processes approximately 30,000 tonnes of ore daily. The ore is crushed in three stages and then ground in conventional rod mill - ball mill circuits with cyclone classification. The cyclone overflow is fed to the bulk flotation circuit as a pulp with a density of 50% solids. The particle size distribution is approximately 35% plus 65 mesh. Bulk rougher and cleaning flotation produce a concentrate grading approximately 20% copper and 4% molybdenum. This concentrate is fed to the separation circuit, where the copper is depressed with sodium hydrosulphide and the molybdenum is floated. These products are further ground and then upgraded by column flotation. The molybdenum concentrate is pumped to the leach plant to reduce concentration of lead and copper. It is then washed, filtered, dried and packed for shipment to Europe. The copper concentrate is filtered, dried and subsequently shipped to Japan.Prior to November 1977, the mill flotation control was carried out by the assay laboratory using a Philips PW 1540 sequential x-ray spectrograph. The assay set consisted of twelve samples, analysed on a two hourly basis for copper, molybdenum, lead, iron and silica.In order to provide elemental composition information on a much shorter sampling interval and to produce speedier control analysis for automating process control, an Applied Research Laboratories PCXQ on stream analyser was purchased. The installation of this analyser, reduced the turnaround time of the control analyses from (2) hours to (20) minutes. At Brenda, the following assays are used in the mill control strategies."

Jan 1, 1989

By Jun Wang, Bo Zhang, Wenqing Qin, Guanzhou Qiu, Xiaozhen Ma, Key Lab of Biohydrometallurgy of Ministry of Education, Fen Jiao, Central South University, Yansheng Zhang

"Arsenic contained in minerals sulphides such as enargite and tennantite can represent not only a significant penalty element in base metals production, but also a disadvantage to the environment through producing the toxic emissions to the atmosphere. The achieving separation of arsenic bearing minerals either at an early stage in floatation or from the floatation concentration is significantly beneficial to the economic. However, there was no feasible commercial method of separation at the flotation stage because of its similar flotation properties with many other copper sulphides. In this work, the selective floatation of enargite from copper sulphide concentrate containing maily covllite, chalcoctie, bornite and enargite was investigated. A low arsenic concentrate with As 0.2%, Cu 22% and a high arsenic bulk concentrate with As 7.65%,Cu 33.65% were obtained. It was indicated that Ca(ClO)2 is the effective depressor and the optimum floatation condition was obtained. Most enargite could be floated at pH 11 and controlling the pulp potential at 290 mV SHE. Furthermore, the arsenic removal from the high arsenic bulk concentrate by hydrometallurgy methods was study. The results showed that the reaction temperature and the concentrations of NaOH were the most important variables affecting the rate of arsenic removal. A low arsenic concentrate with As 0.24%, Cu 37.80% was obtained in the optimum leaching condition.INTRODUCTIONArsenic is mainly produced as a by-product of base metals smelting, in particular copper concentrate. China has imposed an upper limit of 0.50% arsenic for concentrates entering (Long et al., 2012). Arsenic amount of copper concentrate within 0.40% has also been imposed in China, and above which will be introduced about 50 RMB penalties per ton for each 0.10% increasing by smelters now. Therefore, it is necessary to remove arsenic from the copper concentrate.In copper concentrate, arsenic is mainly in the form of arsenopyrite (FeAsS), enargite (Cu3AsS4) or tennantite (Cu12As4S13). There are two types of arsenic in the separation of copper and arsenic: arsenopyrite and arsenic bearing copper mineral. It is easier to separate arsenopyrite from the copper sulphide by flotation in comparsion with the separation of enargite or tennantite from non-arsenic copper minerals (Pineda et al., 2015). The main difficulty in the separation of arsenic copper mineral from non-arsenic copper sulphides is their extremely similar floatability, which depends on the fact that tennantite and enargite contain high copper content (Pineda et al., 2015)."

Jan 1, 2016

By Güney

"An investigation carried out to determine the tendency of coals to heat spontaneously in terms of time-temperature curves coupled with the resulting oxidation products in an adiabatically controlled laboratory setup is described. Tests were made at differing moisture conditions, including oxidation and also oxidation with either adsorption or desorption of water vapour on coal.From the experimental evidence, there is reason to believe that the oxidation of coal, although an important factor, is not the predominant one in the development of spontaneous heating. In addition to the temperature increase in coal and the gaseous products evolved due to auto-oxidation, the process is accelerated by adsorption and retarded by desorption of water vapour on coal."

Jan 1, 1971

By F. Ajersch, A. R. Hekmat

Apparent viscosities of hypo-eutectic (Al-7% Al) and hyper-eutectic (Al-35% Si) binary alloys were measured in the semi-solid state using a Couette type viscometer at variable shear rates. Analysis of the microstructural evolution demonstrates the differences in the rate and degree of attrition of the primary phase particles which are characteristic of the thixotropic nature of the semi-solid alloy. It was observed that the Si primary phase in the hyper-eutectic alloy is much more difficult to fragment than the dendritic a-Al phase in the hypo-eutectic alloy. For the case of the a-Al, the dendritic structure is broken down by attrition and fracture of the dendrite arms whereas the fracture of the Si hexagonal crystals in the hypereutectic alloy occurs along the {100} and {110} cleavage planes. Results are presented for fixed solid fractions of the primary phase at isotherm condition for each type of alloy.

Jan 1, 2006

By G. S. Hume

In the transformation of carbonaceous materials, such as peat, to coals of various grades, the changes are known to be both physical and chemical and the grade of coal finally produced depends on the stage to which alteration proceeded. Those changes, which are frequently spoken of as the results of metamorphism, are due to pressure with accompanying heat and, according to the amount of metamorphism to which the sediments with the included carbonaceous beds have been subjected, there is a gradation from peat to anthracite coal, and even to graphite. The improvement in the quality of the coal as a result of metamorphism is due to an increase of the carbon content of the coal and a corresponding loss of the volatile materials. This rise in the quality of the coal according to the degree of metamorphism is well illustrated by the coals of western Canada. In the Plains area, where the deformation and the attendant metamorphism of the sediments is comparatively small, the coals are lignites, whereas in the mountains, where deformation has been severe, the coals are semi-anthracites. Sub-bituminous and bituminous coals occur in the intervening areas. The same general relationship between the quality of the coal and the degree of metamorphism holds true for the Appalachian basin of the United States, where there is a progressive improvement in the quality of the coals from west to east, that is, from an area of comparatively slight metamorphism to an area of marked deformation in the Appalachian Mountain region. But while it is true that this relationship holds in a general way, it has been found that the improvement in the quality of the coal is not always uniformly progressive, and there may be local variations such that an area containing coal with a carbon content indicating low or medium metamorphism may be surrounded by areas in which the coals are of higher grade. These local variations in many cases can be explained, and they in no way detract from the general rule that, in a region exhibiting a progressive betterment in the quality of the coal from an area of low metamorphism to one of more marked deformation, the quality of the coal, i.e., the amount of fixed carbon in the coal, may be taken as an index of the degree of metamorphism of the coal as well as of the sediments in which it occurs, It has been pointed out (') that certain coals, such as cannels, are unreliable indicators of the varying degree of metamorphism because of the nature of the material from which such coal was derived. Such coals, however, are not known in western Canada and their behaviour need not here be discussed.

Jan 1, 1927

By B. Hart, D. J. Miller, J. T. Francis, M. C. Biesinger, Smart. R. St. C.

Diagnosis of the surface chemical factors playing a part in flotation separation of a valuable sulfide phase requires measurement of the hydrophobic and hydrophilic species that are statistically different between the concentrate and tail streams. Time of flight secondary ion mass spectrometry (ToF-SIMS) can be used to identify sufficient particles of a specific mineral phase for reliable statistics determining a mean value for each species with 95% confidence intervals (1). Using the region of interest (ROI) facility in the Tof-SIMS software, a mass spectrum from each particle, at 1-2 monolayer sensitivity, is recorded and stored. This analysis is reported for a chalcopyrite / pyrite / sphalerite mineral mixture conditioned at pH 9 for 20 minutes in order to study transfer of copper from chalcopyrite via solution to the other two mineral surfaces since this mechanism can be responsible for their inadvertent flotation in copper recovery. Analysis from mineral selection based on specific ToF-SIMS signals (eg. Pb, Zn, Cu, Fe, Fe/Cu) indicated no statistical difference in the copper intensities on pyrite and sphalerite after this conditioning. Principal component analysis (PCA) of the ToF-SIMS imaging data identifies combinations of factors strongly correlated (positively or negatively) in images or spectra from mass spectra recorded at each of 256x256 pixels in a selected area of particles. PCA is a better method of selecting minerals due to multi-variable recognition. It has clearly separated a statistical difference in copper intensities between the sphalerite and pyrite phases. The method has been extended to samples from an operating plant again with excellent phase recognition and diagnostic surface chemistry.

Jan 1, 2004

By D. K. Matlock, D. J. Hamre, J. G. Speer

Ultrafine ferrite (UFF) grains may be produced in surface layers of plate steels using controlled intermediate cooling followed by deformation. Experiments were conducted using a 0.12 C - 1.26 Mn steel on a Gleeble 1500 hot deformation simulator. Taguchi designed experiments were used to evaluate prior austenite grain size, intermediate cooling rate, intermediate cooling temperature, intermediate hold time and amount of reduction in order to observe the effects of variables and their interactions on the final microstructure while minimizing the number of required test runs. Evaluation of resulting microstructures and mechanical properties revealed a preferred thermal and mechanical history for developing ultrafine microstructures in surface layers of plate steels. Application of the fundamental concepts of phase transformations to industrial plate rolling is considered.

Jan 1, 2004

By J. Doucet, C. Price

In an industrial setting, operational changes are continually introduced, driven by new technologies or changing economics. Because of day-to-day variability, quantifying the impact of these changes based on metallurgical performance requires long trial periods to achieve statistically significant results. Tools and techniques developed by the mineral processing group at McGill University have allowed for direct measurement of process variables (e.g., bubble size, gas and solid holdup). Two case studies are described where direct measurement techniques were used to evaluate: a) a new rotor stator mechanism; and b ), the introduction of a new frother type. Application of these methods has accelerated the evaluation of process changes and improved confidence in results.

Jan 1, 2009

By K. H. Poulsen, C. J. . Hodgson

Synvolcanic, layered gabbro-anorthosite sills at Rainy Lake, Northwestern Ontario, reflect a combination of igneous processes including fractional crystallization, wall rock assimilation and possibly liquid immiscibility. Chalcopyrite-pyrrhotite mineralization at the base of the Grassy Portage intrusion accumulated by crystallization of a sulphide liquid during cooling. Upward enrichment of Fe and Ti in this intrusion and also in the Bad Vermilion Lake anorthosite complex culminated with the crystallization of lenses of disseminated to massive magnetite+ apatite+ ilmenite+ rutile. Regional low to medium grade metamorphism and accompanying deformation resulted in recrystallization and local remobilization of ore minerals.

Jan 1, 1984

By R. B. Ellestad

Introduction Lithium has been known since 1817, when it was discovered by the Swedish chemist, Arfvedson, while working in the laboratory of Berzelius on the chemical analysis of the mineral petalite, LiAl(Si205)2. Development of the chemistry of lithium proceeded slowly, following the early work of Davy, Gmelin, Bunsen, and Matthiessen. Approximately seventy years elapsed before lithium products assumed any commercial importance, and for a considerable period it was a' very minor industry. Their chief early use seems to have been in medicine, and in the production of lithiated water. Other more important uses were gradually discovered, and the industry has had a slow but steady growth. Chemistry Lithium is classified as an alkali metal, along with sodium, potassium, rubidium, and cæsium. Like these, it is a silvery-white metal, which can be cut with a knife; it is harder than sodium, but softer than lead" It is remarkable in having a density of only 0.53 gram per cubic centimeter, which makes it the lightest metal. On ignition in air, it burns intensely to form chiefly lithium monoxide, Li2O. Like the other alkali metals, lithium reacts vigorously with water to form hydrogen and lithium hydroxide. The later is a strong base, and reacts with acids to form salts. The salts of lithium are in general analogous to those of the -other alkalies, but many of them have unique properties. For example, lithium chloride and bromide are extremely hygroscopic, and have a very high water solubility. Lithium fluoride, phosphate, and carbonate, on the other hand, are all relatively insoluble, unlike the corresponding sodium and potassium compounds. In this instance, lithium exhibits its frequent tendency to resemble the alkaline-earth group of elements (calcium, strontium, and barium). Many of the special and valuable properties of lithium are related to the extremely small size of the lithium ion.

Jan 1, 1948

By R. B. Hyde

"Severe drilling conditions and difficult mud problems are briefly out-lined as the major cost items in all production operations. The chief problems discussed are abnormal pressures, high temperature, trouble-some shales, and low rates of penetration. These problems have been eliminated or greatly reduced in many areas by• the proper application of recently developed drilling mud products and techniques. These severe problems and their solutions are discussed generally: the application of high-density weighting materials to overcome abnormal pressures; surfactant muds with sodium polyacrylate as a solution for deep and high-temperature drilling; shale control muds and new dispersants for severe shale problems; and low-solids emulsions and •extreme-pressure lubricants for greatly improved rates of penetration."

Jan 1, 1959

By Alisa M. Caswell

Outline: 1. Syncrude: Who are We? 2. Energy Use at Syncrude 3. Historical Energy Focus at Syncrude 4. Case Studies for Process Variable Monitoring 5. Extraction Flood Water Temperature Management 6. Fired Heater Tuning 7. Critical Factors for Success Syncrude: Who are We? ?Syncrude is a Joint Venture Operating Company with one product: Synthetic Crude ?Production Capacity: 350 kbbls/day ?Primary Energy Sources: ??Fuel Gas + Natural Gas ?? Coke ?? Electricity ?? Diesel

May 1, 2008