Search Documents

By Neil Camarta

$6 Billion Dollar Education ?? Construction is like war ? you need a command and control organization ?? A strong Owner?s team is a must ?? Smaller is better ? break the project into bite size chunks ?? New technology is risky ? lots of construction and start-up risk ?? Safety can be successfully managed ?? Don?t expect contractors to ?work well together? ?? Never, ever let Mining Engineers run stuff than can catch fire

May 1, 2008

By S. M. C. Santos

Preliminary bench-scale studies were carried out on the leaching of a zinc sulphide concentrate from Somincor, Portugal, and the purification of the resulting pregnant solution using solvent extraction techniques. The sulphide concentrate contained 36% Zn, 36% S, 2% Fe and 4% Cu. The leaching was carried out with sulphuric acid in the presence of ferric sulphate as the oxidant. Important leaching parameters, such as the effect of reaction time, the solid-liquid ratio, temperature and concentrations of acid and oxidant, were investigated. After leaching, the recovered solution was contacted with an organic phase containing Acorga 5640 to remove the copper. Subsequently, the removal of iron from the leaching solution was achieved with a mixture of Cyanex 272 and TBP. This solvent mixture was relatively selective for iron over zinc. The stripping of the loaded solvent was performed with 200 g/L H2SO4. Six countercurrent extraction stages achieved a separation of about 99% of the iron from the leaching solution. The iron-free leachate can be further treated to recover minor metals by cementation, and finally, zinc by liquid-liquid extraction. The advantages of the suggested process relative to the traditional jarosite process are discussed.

Jan 1, 2006

By E. C. Keeley

THE property of Buffalo Ankerite Gold Mines, Limited, is in Delora township, Porcupine area, Ontario. The southwestern part of the property is ground formerly owned by Marbuan Gold Mines, Limited, which was acquired by Buffalo Ankerite in January, 1936. Until 1938, the Ankerite (or North) mine and the Marbuan (or South) mine continued as separate operations, each developed through a surface shaft and winze to the 1050 level and each having its own mill. This meant high hoisting costs, which, in 1936 and 1937, amounted to 36 cents per ton. In 1938, the underground workings of the two mines were connected on the 1050 level, and ore from both mines was hoisted at the main, or No. 2, shaft of the North mine, location of which is shown in Figure l. This shaft was discontinued at a depth of 1150 feet because, owing to the soft nature of the talc (serpentine) rock in which it was sunk, it had to be concreted throughout, and also because of its great distance--1,100 feet and 1,400 feet, respectively-from the North and South orebodies.

Jan 1, 1945

By O. A. Ojo, O. A. Idowu, N. P. Wikstrom, M. C. Chaturvedi

Transient Liquid Phase Bonding (TLP) of a Nickel base superalloy, Inconel 738, was performed to study the influence of holding time, filler gap size, and temperature on the joint microstructure. Insufficient holding time for complete isothermal solidification of liquated insert caused formation of eutectic-type microconstituents along the joint centerline region. An increase in the eutectic thickness with increase in initial filler gap size was observed in joints prepared at a constant temperature and holding time. In agreement with prediction by conventional TLP diffusion models, an increase in bonding temperature for a constant gap size, resulted in decrease in the time, tf, required to form a eutectic-free joint by complete isothermal solidification. However, a significant deviation from these models was observed in specimens bonded at and above l 175°C. A reduction in isothermal solidification rate with increased temperature was observed in these specimens, such that a eutectic-free joint could not be achieved by holding for a time period that produced complete isothermal solidification at lower temperatures. Considerable enrichment of the liquated insert with base metal alloying elements at higher temperatures is suggested to be an important factor contributing to the observed departure from conventional TLP prediction.

Jan 1, 2006

By William C. Boggis

EKATI? Diamond mine is located 300km northwest of Yellowknife and 200 km south of the Arctic Circle in the Northwest Territories of Canada. The site is a remote tundra area with continuous permafrost and is in the Canadian Shield. EKATI? is the first diamond mine in Canada and is operated by BHP Diamonds Inc., which is a part of BHP Minerals. BHP Diamonds Inc. is an incorporated company based in Vancouver, BC. The mine is a joint venture of BHP Diamonds Inc. (51%), Dia Met Minerals Ltd. (29%), Charles E. Fipke (10%) and Dr. Stewart L. Blusson (10%). The mining area lies within the 10,960 ha land leases held by the joint venture. The total claim block covers 344,000 ha. To date over 136 kimberlite structures have been identified within the claim. Five of these provide the basis for the present mine plan with three others identified for future inclusion. At full capacity the mine will produce 4.5 million carats per year, approximately 4 % of world production and employ approximately 600 people, with over 33% being Aboriginal from the Northwest Territories.

May 1, 2001

By Bruce C. Smart

"Very little attention was given to the regulation of uranium mills by the Atomic Energy Control Board prior to 1974. The ore grade treated by Canadian mills in the past was in the order of 0.08 - 0.3% U and it was not difficult to keep the exposure of workers well below regulatory limits. Furthermore, uranium milling has also been substantially free of occupational illness because environmental control has been generally satisfactory (l).The discovery of higher grade ore bodies in Canada has resulted in higher radiation levels in one mill and this has partly contributed to a need for increased radiation monitoring in the mill. In addition, as greater insight is gained on the effects of radiation, the implementation of the ALARA principle is being stressed at all mills.The concept of ALARA was emphasized by the ICRP (International Committee for Radiological Protection) in 1977 and stands for '""as low as reasonably achievable'"". It is based on the premise that no proven threshold for potential effects of radiation exists and that the actual individual exposure should therefore be kept as far below the regulatory limit as possible, economic and social factors being taken into account."

Jan 1, 1982

By John T. Whetton

"FROM 1850 when the annual production was around 50 million tons, coal output in Great Britain expanded rapidly to 225 million tons in 1900 and 287 million tons in 1913. However, during the First World War, countries which had previously bought large quantities of coal from Britain sought other sources of sup-ply or developed their own coal re-sources. Thus from the record figure of 73 million tons exported in 1913, Britain's coal exports declined until in 1938 they stood at 39 mil-lion tons. An important reason for this was the development of oil engines for marine propulsion. Today, nearly all the navies and mercantile shipping in the world have turned to oil engines. Sometime in the future, however, it is reasonable to expect nuclear power to replace oil.During the Second World War, coal output in Great Britain and manpower at the mines were reduced considerably and in 1.945, 175 mil-lion tons were produced by 709,000 miners. Exports were meagre, only 8.""7 million tons went to foreign consumption. During the severe winter of 1947, inland demand for coal exceeded production and exports were prohibited. Even importation of coal was required to meet inland demand. These were years when the coal industry of Great Britain made immense efforts to secure maximum output irrespective of economy. The energy needs of Great Britain appeared insatiable; but had it been possible to export, the nationalised mining industry could have made huge profits as there was a world shortage of coal. However, home needs were considered to be the priority and many overseas markets were lost. Other producers moved in and secured long-term contracts. Not only was the British export market lost, but also the nationalised industry had to sell the imported coal at the same prices as home-produced coal and suffered losses up to of:3 per ton. Bence, at a time when the National Coal Board might have ac-cumulated a reserve fund to cope with less prosperons times, it was having to spend large sums of money securing sufficient coal for inland consumption. This was a time when intensive efforts in the mining industry, comparable with those of many industries and establishments inclusive of the armed services during the war, would have produced a greater amount of coal and have been of immense value to the country as a whole."

Jan 1, 1960

By X Dai

This paper investigated the loss of cyanide via oxidation in CIP or CIL processes by relating the cyanide oxidation to its major oxidation product, cyanate. The results showed that the oxidation of both free cyanide and copper cyanide complexes are substantially enhanced by the presence of carbon. The rate of cyanide oxidation was found to occur in the order: Cu(CN)32- > CN- > Cu(CN)2-. The cyanide oxidation rate in the presence of copper and carbon increased significantly with increasing dissolved oxygen concentration, typical of CIL vs. CIP conditions. Cyanide oxidation rate of iron, zinc or nickel cyanide complexes was minimal.

Jan 1, 2011

By H. O. Seigel

Induced Polarization includes many types of dipolar charge distributions set up by the passage of current through consolidated or unconsolidated rocks. Among its causes are concentration polarization and electrokinetic effects in all rocks and the phenomenon of Overvoltage in rocks containing electronic conductors such as metallic sulphides and graphite. In normal rocks the polarization effects may be usually con-fined within relatively narrow limits and any large departures may be at-tributable to the presence of electronic conductors. In practice, Induced Polarization is measured in one of two ways. In the first a steady current of some seconds duration is passed and abruptly interrupted and the slowly decaying transient voltages existing in the ~round are measured after interruption. This is known as the "pulse", "transient", or Direct Cur-rent Induced Polarization (D.C.I.P.).The second method entails a comparison of apparent resistivities using sinusoidal alternating current of two or more frequencies, generally within the range of 1/10 to 10 c.p.s. Induced Polarization extends the

Jan 1, 1962

By Hämäläinen M., O. Hyvärinen, E. Jääskeläinen

HydroCopperTM is a new hydrometallurgical process for the treatment of copper sulphide concentrates, which has been developed by Outokumpu. The process includes chloride leaching of copper concentrate, solution purification and precipitation of copper(I) oxide, an intermediate product, which is reduced and cast into copper products. The reduction can be carried out by pyrometallurgical methods or hydrometallurgically in an autoclave. This paper discusses the thermodynamic and kinetic aspects of the hydrogen reduction of copper(I) oxide in an autoclave. The results of the laboratory tests are presented and discussed. Finally, the autoclave method is compared with other options.

Jan 1, 2004

By A. Abdollahi

Modification of the silicon in Al-Si alloys can be performed by adding a very small amount of some elements like Na, Sr and Ca to alter the form of silicon from an acicular shape to a fine fibrous one. This modification results in a considerable improvement in mechanical properties especially elongation, Metallographic observations in A356 alloy indicated the degree of the modification with Na, Sr and Ca, They showed that the effect of Ca as a modifier is not as strong as is Na or Sr while Na is the most effective modifier, Although modifiers improve mechanical properties, they also increase porosity in castings, The reduced pressure test (RPT) and Tatur test showed that the increasing porosity with Na is the most and with Sr is the least.

Jan 1, 2004

By G. F. Round

In order to obtain values of angle of shearing resistance and initial resistance for McMurray oil sand for use in general design calculations, the shear strength of this oil sand was measured in a controlled strain type tester, modified so that the rate of deformation could be varied between 0.01725 and 0.1869 inches per minute. Effect of temperature was investigated by adapting the equipment to operate at both 71 ° and 185 °F. The data are reported in terms of angle of shearing resistance and initial resistance for varying rates of deformation, composition and temperature. While the main sets of results reported here were obtained at a bulk density range of 108.7- 109.5 lb. / cu. ft., some results were obtained at a bulk density range of 101-102 lb. / cu. ft. Analysis of varance tables have been drawn up from the results obtained from least squares correlations and significance tests applied. It was concluded that oil content and temperature were significant variables for the degree of shear strength developed by the oil sand; increase of oil content and decrease of temperature each cause an increase in shear strength. The bulk density range 108.7 to 109.5 lb./cu. ft. gave angles of shearing resistance from 30° to 40° and initial resistance values of 0.37 p.s.i. to 0.85 p.s.i. For the bulk density range 101 to 102 lb. / cu. ft., lower values of shear strength were obtained, indicating that compaction density was also of importance

Jan 1, 1960

By S. H. Schulz

100 YEARS AGO, on the first of August, 1877, the mining engineer Friedrich Koepe was granted the patent rights for a hoist driving ropes on the principle of friction. It was named after him: the Koepe hoist. On the occasion of this centenary, the main features of the Kcepe principle are described.

Jan 1, 1977

By W. Harry Foster

"Asbestos Corporation Limited, incorporated in 1925, operates four asbestos mines and three asbestos mills in the Thetford Mines 1•egion of Quebec's Eastern Townships. A unique asbestos orebody, located in the Ungava Peninsula of Nouveau Quebec, was purchased by Asbestos Corporation Limited in 1964 and commenced production in 1972. As there were no existing facilities in the isolated, arctic region of Asbestos Hill, it was necessary for Asbestos Corporation Limited to construct at Deception Bay a deepsea wharf, a large ungraded fibre shed, a power plant and camp facilities. Forty-two miles of road were needed and were constructed from Deception Bay to Asbestos Hill. At Asbestos Hill, a complete crushing-drying-milling complex, a power plant, pe1•sonnel accommodations and open-pit facilities were provided. Unloading facilities and a fib1•e finishing mill we1l constructed at Nordenham, West Germany. The ""Asbestos Hill- Nordenham Story” is divided into individual papers covering all aspects of the engineering, construction and operation of this unique enterprise. Particular emphasis has been placed on those unusual aspects caused by the isolated location, arctic conditions, short shipping season and the deep permafrost."

Jan 1, 1976

By H. Kuboyama

The synergistic effects of polymer additives such as gelatin and polyethylene glycol) (PEG) and Cl- on Cu electrodeposition have been investigated by measuring the polarization curves for Cu deposition, by rotating ring-disk electrode technique and by AC impedance measurements. The cathode potential for Cu deposition was greatly polarized in solutions containing both Cl- and gelatin or PEG, showing evident synergistic effect of polymer additives and Cl- on Cu deposition. The cathode potential was shifted to the less noble direction with increasing the concentration of Cl- in solutions containing polymer additives and showed the maximum polarization at Cl- concentration range between 0.1 and 1 mmol/L. The rotating ring-disk electrode technique revealed that Cu deposition in solutions containing small amounts of Cl- proceeded with initial formation of adsorbed intermediate CuClad. The Cole-Cole plots obtained by AC impedance techniques suggest that the reduction of CuClad is suppressed by polymer additives. The morphology of Cu deposited from solutions containing both PEG and Cl- showed the compacted surface composed of smaller grains due to an increase in the overpotential for Cu deposition.

Jan 1, 2007

By D. P. Fenton

The Phelps Dodge El Paso Rod Mill produces approximately 2.4 million pounds per day of copper rod from a casting and rolling operation. The newly formed rod is treated to remove mill scale and oxides using a sulfuric acid and hydrogen peroxide solution which is bled periodically when the copper concentration reaches 30-35 g/L. The bleed solution is heated to 75° C to destroy the residual peroxide. Copper is then recovered in a 270 cell EMEW electrowinning plant. Clean acid is also regenerated in the EMEW plant and is returned to the rod cleaning circuit. The EMEW plant commissioned in January 2006, has two operators and replaces a copper sulfate plant with fourteen operators. The EMEW plant has a capacity of 1700 kg/day of cathode copper at 2.1 kWh/kg copper deposited. The electrowinning plant operates in closed circuit with the rod mill returning up to 2600 kg/day of sulfuric acid resulting in zero discharge. Use of dimensionally stable anodes (DSA®) ensures that the acid quality is maintained in the closed loop operation. The operating conditions, performance and plant experience of the EMEW copper and acid recovery plant are discussed.

Jan 1, 2007

By A. Rodriguez-Prado, R. L. Legge, W. C. Lennox

ABSTRACT It is possible to adequately describe chemical reduction of hexavalent chromium, Cr(VI), in industrial and mining wastewater in constructed wetlands by applying different kinetic models (e.g., halforder, second-order). Accounting for hydraulic transport of contaminants in reduction equations can also improve such description. The authors developed an explicit advection-dispersion bulk flow equation and applied it to model Cr(VI) reduction in laboratory wetland mesocosms. The results indicated that the model adequately described wetland exit Cr(VI) concentrations and Cr(VI) reduction, representing an improvement over the commonly used graphic method and potentially improving the wetland design.

Jan 1, 2014

By H. Fuchs, W. Hilger, E. Prosser

"The Lone Gull discovery of Urangesellschaft Canada Limited was made in 1974 as a result of extensive exploration activities for unconformity related uranium deposits in the Baker Lake area of the Northwest Territories. The structurally controlled mineralization is hosted in Aphebian metasediments and intrusive granitic stocks located approximately 2 km south of the unconformity between the Lower Proterozoic Aphebian and the Middle Proterozoic The/on Formation.The original discovery was made with a helicopter mounted radiometric system during systematic prospection over the unconformity. Diamond drilling was first carried out in 1977 and continued, with an interruption in 1981, to the present. A total of 25,500 metres and 199 holes have been drilled and outlined three ore zones. Preliminary geological reserves are estimated at some 16 million kgs. U30 8 at an average grade of approximately 0.4%.IntroductionUrangesellschaft initially entered exploration in Canada as a participant in joint ventures in 1968, and was incorporated in Canada in 1974 as Urangesellschaft Canada Limited. Subsequently, UG was among the first companies to apply exploration criteria developed from the Athabasca Basin, namely the Middle Proterozoic unconformity over Archean/ Aphebian basement, for selection of exploration targets in the geologically similar Thelon Basin.The Baker Lake area in the Keewatin District of the Northwest Territories was selected from the extensive Thelon Basin because it had the best accessibility (Fig. 1). The hamlet of Baker Lake located close to the geographical centre of Canada, is largely an Inuit settlement with a population of approximately 1,100 inhabitants. The distance from Baker Lake to the Lone Gull property is about 80 km. Baker Lake is connected to the tidewater of Hudson's Bay via Chesterfield inlet and is serviced by scheduled domestic flights several times weekly from Churchill, Manitoba, about 650 km to the south."

Jan 1, 1986

By A. J. Ouellet, A. Coulombe, B. Salmon

The no. 7 vein system cuts the Ventures gabbro which has undergone folding and fracturing; the latter, in response to movement on the nearby Campbell Lake fault. It fills a shear fracture which pinches and swells in the upper mine levels but has a more uniform width in the lower levels. The best copper and gold grades in the upper levels occur in the widest parts of this structure. The vein is richer in quartz on upper mine levels and in carbonate on lower levels. The north wall of the vein is more affected by major and minor element wallrock alteration than the south wall. The isocumulative ci;rves for gold and copper show a direct correlation between the two metals in the upper levels and their increased concentration in the wider parts of the vein. Gold grade decreases in lower levels. A proposed structural model identifies the no. 3 and no. 7 veins as second order conjugate fractures, related to the Campbell Lake fault. The fractures pattern suggests that a conjugate system developed between these two parallel veins as a consequence of rock competence and a relatively low confining pressure.

Jan 1, 1984

By C. E. Baltzer, W. H. Harper

"This study has been developed to illustrate the trend and pattern of distribution applying to the quantities and costs of the fossil fuels used, and the related amounts of electricity generated, in the thermal segment of the Canadian electric utility industry.Traditionally, Canada's requirements for electric energy have been preponderantly met by hydraulic power. The need for augmented supplies of thermally generated power has mainly developed since the close of World War Il-in an era that has seen drastic decline in the production of indigenous coal and buoyant expansion in the supply of oil and natural gas. Although coal currently is faced with serious competition from the fluid fuels, the utility industry in particular promises an advancing market for coal, because of its abundant resource, at prices less likely to show sharp increase. For Canada as a whole, this trend has been progressive since 1959, and, unbelievable as it may now seem, the extent of the advance by 1975, particularly in Ontario and the Prairie Provinces, may well be as much, or even more, than the present rate of consumption for all purposes.The text and the tables and charts are arranged to focus attention on: the growth of thermal genera ting capability; the historical trend in consumption of fuel and the related production of electricity; patterns of distribution by types of fuel and thermal capacity; the relationship of steam to other sources of thermal capacity; and the quantities, costs and related percentages of electricity generated by types and kinds of fuel used, both regionally and provincially."

Jan 1, 1966