Search Documents

By G. G. Bowser

Introduction Flame shots are of very infrequent occurrence in the coal mines of Nova Scotia. Probably not more than one is recorded in three months. Many shot-firers have never experienced one, and many never will. As a consequence, although all such occurrences are very carefully investigated, information concerning the cause of flame shots is somewhat meagre. In the course of the years, however, something has been learned of the practices and conditions that are responsible for them. During the past ten? years, over seventeen million shots were fired in the coal mines of Nova Scotia and only fifty-two faulty shots were reported or investigated during that time. In thirty-nine of these, flames were reported; in five, sparks only; and in eight, smoke only. In eight of these occurrences, unburned explosive was found after firing. In one of these eight, flame was seen in the back part of the hole, and an accompanying hissing sound pointed to burning explosive. In four of them, there was no evidence that gas was not ignited. All samples of explosives from these faulty shots which were submitted for analysis were found to be normal, except two, in 1937, which contained excessive moisture. These two samples were from two following shots in the same room on the same day. The initial cause of trouble with all eight shots was one or several of the following: explosives in poor condition, separation of cartridges, incorrect priming, shot hole in poor condition or not properly cleaned. In the case of sixteen or seventeen of the thirty-nine shots which flamed, data are insufficient for conclusions to be drawn as to the cause of the flame.

Jan 1, 1947

By D. W. Bacon

Plant process optimization programs are often costly, both in technical effort and loss of production. Evolutionary Operation or "EVOP" is a mode of plant operation consisting of controlled cyclical changes in process conditions by which information is provided concerning potential process improvements while both volume and quality uniformity in production are maintained. Its conceptual simplicity and low cost of utilization have led to successful adoption in a variety of industrial manufacturing operations. This paper is an expository account of basic EVOP theory, the problems encountered and the organization required in applying it to a processing plant. Illustrations are provided which indicate the payoff that can result.

Jan 1, 1967

By L. L. Bolton

The Department of Mines as at present constituted has evolved from the organization which came into existence following the passage of the Geology and Mines Act by the Dominion Parliament in 1907. At the outset, it may be said that it is not a function of the Department of Mines, nor of any of its branches, to administer the mining rights vested in the Crown. The title to Crown lands in the provinces of Nova Scotia, Prince Edward Island, New Brunswick, Quebec, Ontario, and British Columbia ( with the exception of certain specified areas, such as Indian Reserves, Ordnance Lands, the Railway Belt of British Columbia, and the Peace River Black) is vested in the respective provincial governments ; the title to Crown Lands in the provinces of Manitoba, Saskatchewan, and Alberta, the Yukon and Northwest Territories, and in the Canadian Arctic, is vested in the Dominion Government, and matters pertaining thereto are (with a few exceptions) administered by the Department of the Interior, Ottawa. Nor are statistics of mineral production at present collected and published by the Department of Mines. This function did belong to the Geological Survey from 1886 to 1906, and to the Mines Branch from 1907 to 1920; but commencing with 192l this duty was transferred to the Dominion Bureau of Statistics, consequent upon the decision of Government to place the collection of all statistics under the direction of one officer.

Jan 1, 1929

By J. B. Edwards

"The case is presented for the use of simulators for the computer-based training (CBT) of mining plant operators and for introducing them to automatically controlled systems. As well as their use in the classroom, the role of simulators is examined for ""on-plant"" use in trouble-shooting, fault-finding and maintenance of automatic systems. Case studies are presented showing how specific simulators are becoming established or have potential in the areas of automated materials handling, machine testing, setup and guidance. The evolution of scientific simulations into simulators of widespread practical use is discussed and present-day limitations of computer speed and graphics are considered. Related areas of research for the Canadian Centre for Automation and Robotics in Mining (CCARM) are identified.IntroductionCCARM's Commitment to Simulator DevelopmentAs automation is progressively developed and exploited in mining operations, there arises an urgent need to educate and train staff responsible for its introduction and operation in our mines and for its maintenance. For this purpose , an essential ingredient of an automation program is the development of appropriate mining system simulators for use by a wide variety of personnel. The author has been fortunate to have been closely involved with the development of automatic control systems for a variety of mining machines and mining systems in the United Kingdom. A key ingredient of the research phase in each case has been the use of simulation techniques. As projects have moved toward their commissioning and exploitation phase, the simulations have evolved into simulators tailored for use by machine operators and maintenance personnel. Illustrative case studies are presented later. The researach of the newly constituted Canadian Centre for Automation and Robotics in Mining (CCARM) will likewise involve extensive simulation, and the development of simulators (from the scientific programs) for use at the mine by operators and technicians will be given high priority in the Centre's over-all work program."

Jan 1, 1990

By S. Qian

Galvanic corrosion is a potentially major concern associated with the application of stainless steel reinforcement which is in direct (electrical) contact with carbon steel reinforcement in concrete structures. Judicious use of stainless steel rebar in both new construction and rehabilitation of older structures is a viable, cost-effective option for extending service life and reducing maintenance costs. Questions, however, had arisen about the possibility of increased corrosion due to galvanic effects. This paper investigates the galvanic-coupling behaviours of three different types of stainless steel and carbon steel. Tests were performed both in electrochemical cells and with specimens in concrete inside an environmental chamber. The results show that oxygen reduction on stainless steel is the rate-determining factor for galvanic coupling of these two metals. It is much lower than that of passive carbon steel. As a result, the galvanic coupling of stainless steel with carbon steel will not increase the risk of corrosion of carbon steel reinforcement.

Jan 1, 2005

By Alan Bauer

New developments in drilling, blasting and explosives in both open-pit and underground mining operations are discussed, as well as novel surface blasting techniques such as are used in tar sand mining.

Jan 1, 1978

By W A. James

The use of spectrographic semi-quantitative analysis has recently been of considerable value in establishing the geological relationships in a complicated orebody. The principal minerals found in the Mount Pleasant orebody are cassiterite, stannite, sphalerite, molybdenite, wolframite, chalcopyrite and galena, associated with arsenopyrite, pyrite and fluorite. In addition to the large number of minerals, a further com-plication is the non-uniform distribution of the economic minerals, with one mineral being the only one present in major amounts in one area and another mineral being predominant in another area. At the same time, all minerals are present to a minor extent throughout the deposit. This heterogeneity made it advisable to analyse all exploration samples thoroughly. Analysis by conventional means would have resulted in prohibitive costs. By the use of emission spectroscopy, however, it was possible to obtain, quickly and relatively inexpensively, a reasonably comprehensive picture of the orebody un-der investigation.

Jan 1, 1963

By M. A. Vos

"Cretaceous sands and clays underlie an area of approximately 5,000 km2 in Northern Ontario, southwest of James Bay. The deltaic deposits occur as a wedge of continental sediments to the north of an east-trending fault scarp referred to as the Precambrian Escarpment. They rest on older sedimentary formations of the Moose River Basin (Jurassic, Devonian) and are covered by glacial tills and marine sediments of the Quaternary period. Outcrops are restricted to occasional exposure in the deeply incised riverbeds.In 1975 and 1978, drill programs sponsored by the Ontario Government provided new information on the extent and quality of the deposits. Fourteen holes at approximately 12-km intervals were drilled to a maximum depth of 189 m by reversed- circulation chip drill methods. Some core was obtained as well. Analytical results show that the thickness of Cretaceous deposits exceeds 100m in several instances. Abundant kaolinitic clay and quartz sand of glass-grade quality, both unique materials in Ontario, are available in an area where hydroelectricity and lignite resources combine to enhance the energy outlook.IntroductionThe presence of refractory clay in deeply incised riverbeds in Northern Ontario was known to geologists travelling the rivers as early as 1875. Robert Bell (1877) reports outcrops of clay and lignite on Coal Brook, a tributary of the Missinaibi River. E.B. Borron in 1880 collected a sample of clay from the bed of the Missinaibi River which H.H. Croft of the University of Toronto considered to be ""nearly if not quite, equal to the Cornish clay used in the manufacture of English porcelain"" (Keele, 1920, p. 42). The Cretaceous age of the clay, sand and lignite deposits was determined with the help of plant remains collected by Keele. He referred to the deposits as the Mattagami series, which later became the Mattagami Formation."

Jan 1, 1982

By J D. McDonald

This paper outlines the function of the Safety and Compensation Division of the Mining Association of British Columbia. After a general discussion of safety and the safety program now being followed in B.C., the author goes on to describe the wide-ranging aspects of compensation payments and company assessment rates. Special attention is also given to the problem of silicosis in mining operations. In appendices to the paper, the experience rating plan of the mining industry is compared to that recently adopted for the construction industry. Introduction The Mining Association of British Columbia consists of fifty-five member companies, including virtually all the producing mines as well as the larger exploration, contracting and development companies. On completion of an extensive study of safety and compensation in the mining industry, the Mining Association of British Columbia instituted a Safety and Compensation Division in 1954. The director of the Safety and Compensation Division reports to the Executive Committee of the Association. There are two main functions of this Division. First is the prevenion of accidents by encouraging

Jan 1, 1965

By Sunil S. Gandhi

Magmatic-hydrothermal deposits rich in magnetite and/or hematite form a broad group that includes monometallic Fe deposits and polymetallic (mainly Cu and Au) deposits. They show a considerable variation in deposit characteristics, but share the genetic processes of magmatic differentiation and related hydrothermal activity in intermediate to felsic melts, and in some cases involve brines and/or meteoric waters during mineralization. They include several world-class deposits. They range in age from Proterozoic to Recent, and form important metallogenic districts in Scandinavian, Canadian, Brazilian and Australian Shields, Circum-Pacific regions, and in China, Iran and Turkey. Monometallic deposits have been important sources of iron in the past and still contain significant resources of the metal, e.g., the Kiirunavaara deposit in Sweden. The giant Olympic Dam Cu-Au-Ag-U-REE deposit was discovered in 1975, and since then explorationists have focussed on search for analogues worldwide. This has brought to light a number of economically important new deposits and prospects, including examples in Canada. The discoveries have in turn prompted considerable research on individual deposits and the group as a whole. This short paper is an attempt to summarize the main aspects of the group from the literature cited in Gandhi and Bell (1996), and from the papers published recently in two milestone volumes on these deposits, edited by Porter (2000 and 2002).

May 1, 2003

By G. E. Veins

A three-phase, continuously-operated, 250 kv.a. electric smelting furnace has been installed at the Mines Branch, Department of Mines and Technical Surveys, Ottawa, for the experimental treatment of ores and by-products of interest to the Canadian mining, metallurgical, and chemical industries. In the operation of this furnace particular emphasis is placed on the accumulation of quantitative data which will be useful in determining the most suitable smelting technique and the nature of the products, and in arriving at preliminary conclusions regarding the cast of power and electrodes. The results obtained in the experimental smelting of iron, manganese-iron, titanium- iron, nickel, and chromiumiron ores, and of a number of industrial by-products, clearly show the value of such treatment for materials of this type.

Jan 1, 1957

By C S. Walker

This paper analyzes the physical, operational and economic site conditions which were conducive to the design of a diesel-electric power plant wherein the over-all use of the thermal energy of the fuel exceeds 80 per cent. The heat energy supplied to the diesel engines is recovered in power generation, vapour phase cooling, waste heat boilers, air to exhaust gas heat exchangers and lubricating oil coolers. Electric boilers are also integrated into the plant design to enable the ratio of electric power output to heat recovery to be varied to suit the seasonal and daily variations. The criteria relative to thermal and electric power design requirements are discussed, and the design details of some parts of the plant which conform to these criteria are illustrated. Some data in regard to the actual operation of the plant over a short period are also included. Introduction THE Cantung mine (Canada Tungsten Mining Corporation) is located some 180 miles north-east of Watson Lake, Yukon Territory. It is situated on the upper reaches of the Flat river at an elevation of about 3,700 feet.

Jan 1, 1965

By R. A. King, B. G. Hunt, C. E. T. White

"This paper reviews the history, occurrence, properties, and uses of indium, and describes the commercial production and fabrication of that metal by The Consolidated Mining and Smelting Company of Canada, Limited (Cominco), at Trail, B.C'. Indium is produced commercially at Trail from dross retreatment furnace D.R.F.) slag, a complex by-product of the lead smelting operations. Furnace feed prepared from this slag is smelted with coke and limerock in an electric furnace. The e1ectric furnace bullion is parted electrolytically, producing a market-able lead-tin alloy containing about 8 per cent tin, and leaving the indium in the anode slime. Recovery of indium from the anode slime involves roasting the slime with sulphuric acid, followed by leaching with water, purifying the leach solution, recovering the indium by sponging with zinc or aluminum, and re-fining electrolytically. This process yields standard grade (99.97+ per cent) indium which is either sold or refined •to high purity ( 99.999 per cent) indium for special uses requiring higher purity metal."

Jan 1, 1959

By Rodrigo Serna, Nora Schreithofer, Zoltan Javor, Kari Heiskanen

"Mineral floatability is a function of mineral properties such as size, liberation, shape, surface composition, reagent coverage on the surface, level of oxidation on the surface, etc.; pulp chemistry: Eh, pH, temperature, DO, reagent type, etc. and hydrodynamic conditions: turbulence, gas dispersion, D32, etc. The biggest challenge with predicting the floatability of an ore is finding a measurement method that would take into account the effect of all of the variables on the floatability of the minerals. The particle-bubble attachment time measurement is considered as an alternative way to predict the floatability of minerals instead of using expensive and time consuming flotation tests because it takes into considerations both surface chemistry and hydrodynamic parameters present in the froth flotation. The existing particle-bubble attachment time method is suitable for studying some significant flotation variables such as pH, temperature, particle size, reagent type and concentration. Nevertheless, measuring the attachment time as a function of collector coverage or surface oxidation is much more challenging. This paper introduces a new induction timer designed to measure the effect of galvanic interaction on the attachment time of particles. The new setup employs an array of needles to create 6 bubbles with the average size of 2.1 mm. Imaging system is used to set the initial distance between the particle bed and the array of bubbles. The attached particles are collected and sent for further analysis. One of the main benefits of the new experimental setup is that the attached particles can be physically separated from the unattached particles therefore many of the particle properties can be analysed and evaluated.INTRODUCTIONSchumann (1942), and Tomlinson and Fleming (1963) proposed that the flotation rate constant is dependent on four probabilities: particle-bubble collision (PC), particle-bubble attachment (PA), particlebubble aggregate stability in turbulent environment (PE), and particle-bubble aggregate stability in froth phase (PF). Any change in any of these probabilities will affect the overall flotation rate constant. All of the above-introduced probabilities are influenced by stream- variables and mechanical variables but their extent of influence vary. The stream variables are particle properties that have been shown to affect flotation rate constant such as size, shape, liberation, mineralogical composition, reagent surface coverage, surface oxidation, etc. The mechanical variables are the direct and indirect properties of the flotation unit affecting flotation rate constant such as cell and impeller geometry, air rate, impeller speed, air holdup, bubble size, residence time, hydrodynamics, froth depth, etc. For instance, the probability of collision is affected by many mechanical variables (bubble size, hydrodynamics, bubbles holdup etc.) but only one stream variable (particle size) has a major effect on it. On the other hand the probability of attachment is affected by much more stream variables: particle size, shape, liberation, surface composition, particle surface oxidation and collector coverage, Eh, pH, etc."

Jan 1, 2016

By Robert R. MacLachlan

New underground mining technology is evolving through the use of large-diameter bore holes containing individually restricted charge weights. This article presents summary observations on cube-root scaling trials using single and rows of charge blasting in sand and in frozen ground. These observations have some bearing on the evolving underground practice, especially where charges of appropriate geometry are used.

Jan 1, 1978

By D. S. Robertson

More than 700,000 feet of diamond drilling was completed in the Blind River area between 1953 and 1958. Much of this drilling was at depths which are still not usual in North America. However, as the tendency is to deeper holes, factual data from the Blind River operation may well provide information of value in future programs. Rates of drilling decreased with in-creasing depth, but uncommonly good rates (an average of over 50 feet per day over more than 4,000 feet of hole) were achieved with proper engineering and care. Costs varied as contractors and geologists became familiar with the area Hole deviation in the Blind River area was locally severe and control of the hole trace became a major problem. Careful surveying was necessary and found to be highly re-liable. It was found that control of the hole trace above 1,500 feet was much more difficult than at depths below 1,500 feet. This is explained by the mechanics of the drilling operation. Various methods of controlling hole deviation were attempted and,

Jan 1, 1962

By U. Storck

"Shaft sinking for exploitation of the deep potash beds in Saskatchewan involved great difficulties from the very first because of the need to exclude from the shaft the high-pressure water encountered in the overburden. Control of the troublesome Blairmore quicksands was achieved relatively quickly by use of the freezing method and by lining with cast iron tubbing. The unsolved problem remained, however, of sealing the water-bearing Devonian where the formations had extremely low permeability and were thus hard to grout. Long experience in German potash mines had shown that the permanency of the whole mine would be seriously endangered if large amounts of unsaturated salt water were allowed to flow in from the shaft wall and merely removed by pumping. The prevention of water movement and the resulting dissolution of salt in the overburden were known to be most important. In the Alwinsal shaft, water flow from the Devonian has been prevented by the use of a steel and concrete sandwich lining similar in principle to a kind of lining introduced a few years earlier, and for another reason, in German coal shafts. As its installation is neither more expensive nor more time consuming than that of cast iron tubbing lining, this same lining was also chosen as protection against the Blairmore quicksands. The great advantage of the steel lining, in addition to its relatively high strength, is the fact that it is possible to make the joints of the individual segments absolutely and permanently water-tight by means of tested welds. The virtual dryness of the Alwinsal shaft will also result in lower costs because significant corrosion of all its steel installations, including skips, cage and ropes, will be prevented."

Jan 1, 1968

By C. H. Tiernon

"This paper was' prepared to emphasize the part that coal washing tables can play in the development of many of the reserves of coking coals in Western Canada_ It covers a brief history of the development of the coal washing table through the present third-generation unit, which suspends from overhead steel beams and is driven by a counter-rotating gear mechanism. The design and operation of this unique table are covered in detail.An analysis of actual operating data is included, with explicit statistical breakdowns of the table products. The data used were actually produced by operating coal companies, and also produced by the United States Bureau of Mines while gathering data for a research investigation. Table feed capacity is discussed, as well as performance criteria and the parameters of relative table performance. Several typical table flowsheets are described, emphasizing the specific reasons for their use. The paper covers the past and present value of the table to the United States coal industry, and makes mention of the newest addition to the family of suspended, multiple-deck, counter-rotating, gear-driven, coal washing tables, the CONCENCO ""88"" Deister table."

Jan 1, 1973

By Ralph H. Cleland

GENERALLY speaking, the Industry lost ground in 1941 in its accident experience. Though the frequency of compensation accidents was but slightly higher than in the previous year and well below past experience, our fatality rate shot up to that obtaining in 1938, and the average cost per man employed was the highest for some time. The number of fatalities was 56 in 1941 as against 33 in 1940. The average cost of compensation per man employed was $34.25 in 1941 as against $28.43. There was but a slight increase in the number of men employed. Accident prevention efforts were maintained, as shown by our frequency, but our accidents were of a more serious nature. In a period of considerable labour turnover, with many new men entering the Industry, especially the base-metal division, and much mental distraction, we might well have expected a high rate of accidents. That this did not occur is a tribute to managers, supervisors, and workmen alike. We all regret the high fatality rate and one must consider why this occurred. So far as it is possible to determine, there is no apparent explanation. There were no disasters. The accidents occurred to the same class of work-men, both in respect to jobs and age groups, and from the same age-old causes that we all know so well. Luck is a big factor in the seriousness of an accident; the solution lies in preventing accidents, even first-aid cases. Generally speaking, if minor accidents do not occur, major accidents do not occur.

Jan 1, 1942

By R. D. Westervelt

IN JULY 1954, the first iron ore from the deposits in the Knob Lake vicinity was mined and shipped to Seven Islands. The beginning of the production may well be the greatest advance in Canadian economy in the past fifty years. In 1955, the Canadian iron ore output was more than twice that of 1954, an in-crease due principally to the iron ore shipments from the Knob Lake area. Previous to this, Canada's iron production was 1.85 per cent of the world's output. Now, this percentage has risen to approximately 5.5 per cent and shows every indication of increasing further as the production rate from the area is increased. In 1955 the Iron Ore Company of Canada shipped over 7 million tons of iron ore and expects to ship over 10 million tons in 1956. Present facilities may be enlarged to handle up to 20 million tons per year. If the expected I 0 million tons per year are exported, Canada's iron exports will be second only to her wheat and newsprint exports. Before production began from the Knob Lake deposits, years of development were necessary in the area. Geologists spent several summers mapping the general area in order to unravel the complicated stratigraphy and petrology. Particular attention was paid to the mapping of the iron formation and all stages of alteration from fresh iron formation to ore were observed.

Jan 1, 1957