Search Documents

By Dr. Ralph W. Edie

The limestone reef reservoir at Swan Hills consists essentially of a "buildup" of successively smaller atoll-like layers. Precipitation of calcium carbonate within the lagoonal area of each layer essentially kept pace with growth of the outer organic lattice. Within the reef mass, six de-positional environments characterized by specific suites of fossils (or fossil fragments) and associated limestone textures are recognized as follows: ( 1) Aerated moderately agitated water of normal marine salinity (widespread shelf or submerged reef-built platform). Thamnopora-type corals, Amphipora, "pancake" stroma-toporoids, crinoids, articulate bra-chiopods, rare rugose cup corals, and ostracods occurs in light gray-buff skeletal microgranular limestone of low permeability. (2) Semi-stagnant quiet water of normal marine salinity (leeward side of reef). Crinoids, articulate brachio-pods, rare thamnopora-type corals, Amphipora, pancake and bulbous stromatoporoids, rugose cup corals, ostracods and gastropods occur in impermeable dark brown argillaceous skeletal calcilutite with thin black bituminous shale beds and rare dark chert nodules.

Jan 1, 1961

By J. C. Roy, S. Couture, C. Barbeau

The chemical composition of the asbestos tailings from different mines in the Eastern Townships of Quebec are fairly uniform in composition. The serpentine minerals antigorite and chrysotile form about 85 to 90 per cent of the total. Iron oxides add another 7 to 10 per cent; magnetite represents about 70 per cent of the oxides. Chromite is present in amounts of about 0.5 per cent. The average contents of elemental magnesium, iron and nickel are 23, 6 and 0.25 per cent respectively.

Jan 1, 1972

By Robert D. Brown, Robert B. Parsons

"The mining industry may have survived the October 28 federal budget relatively unscathed, but the same certainly cannot be said of the petroleum sector-and many mining men are left wondering if their industry will be the next one to be singled out for special attention, as federal and provincial governments seek additional revenues and pursue nationalistic or provincial policies.Higher taxes, higher prices, a potpourri of ""incentives"", and a -""Canadianization"" policy mark the principal features of the new National Energy Program released by the government along with Finance Minister MacEachen's budget address.This month, Tax Notes examines the federal budget. with appropriate emphasis on the National Energy Program and its possible future implications forthe Canadian resource industries.IntroductionMost of the Canadian mining industry (tar sands miners excepted) heaved a sigh of relief on the evening of October 28, 1980, as Finance Minister MacEachen confounded the prophets in his budget address by not raising personal or corporation taxes and by making only relatively modest changes in the general tax system. Instead, he concentrated on a sweeping new energy policy. Unfortunately for that important sector of Canada's mining industry which is involved in mining the country's vast tar sands reserves, either now or in the future, the National Energy Program that was introduced along with the budget 'has serious implications."

Jan 1, 1981

By H. Miki, S. Wheatley

The addition of precipitated silica greatly enhances chalcopyrite leaching in the presence of sodium chloride at moderate temperatures (65-90°C) in acid media with ferric ions as the oxidant. The beneficial effect increases with the increase in chloride concentration and temperature. The addition of sodium silicate and silica sand has no significant influence. The analysis of solubility data in acid/salt solutions indicates that the solubility of silica as Si(OH)4 as the dissolved species is controlled by the activity of water, as expected from the hydration theory. Kinetic analysis shows the trends that copper dissolution from chalcopyrite in the presence of precipitated silica with sodium chloride follows a shrinking sphere model indicating a chemically controlled surface reaction. The effect of temperature on copper dissolution in the presence of both precipitated silica and sodium chloride was also larger compared to the results in sodium chloride alone. The SEM analysis shows that chloride and silica facilitates the precipitation of sulfur on the surface of the silica particles rather than the chalcopyrite particles which avoids the blockage of the mineral surface and thus improves the leaching kinetics.

Jan 1, 2014

By Mohamed Sassi, I. Kolo, R. L. Sousa, R. K. Abu Al-Rub, Manhal Sirat

"Fractures induced by folds are pivotal in hydrocarbon exploration, ground water transport and harnessing of geothermal energy. This is because of the need to predict and understand fracture propagation in reservoirs which have folded rock formations. Despite its prominence, there is a lack of reliable numerical models for simulating fractures resulting from rock folding. This is partially due to the difficulty involved in fracture modelling. As a contribution to fold-fracture modelling, this work applies a coupled plasticity-damage model to rock fracturing and anticlinal folds. Parametric studies on a single folded layer give insight into the fold formation and behaviour. The anisotropic continuum damage model which considers both tension and compression is formulated using the power damage evolution law. For ease in formulation, strain equivalence hypothesis is adopted whereby the strain is the same for both damaged and undamaged configurations. Lubliner plasticity yield criterion is adopted for plastic deformation. The model is coded in Abaqus user subroutine UMAT and is applicable to quasi-brittle materials.INTRODUCTIONThe understanding of fractures in the earth’s crust helps in the prediction, evaluation and characterization of fractured reservoirs, whether they are petroleum, geothermal or underground water reservoirs. This is partly because reservoir permeability and stability are dependent on fracture properties (Nelson, 2001). To achieve this, various approaches have been developed to analyze reservoir rock fractures. These could be grouped into (a) discrete approaches – where the rock mass is represented by a finite number of well-defined components and (b) continuum approaches – where the mathematical assumption of an infinitesimal element is made (Jing, 2003). Ivanova (Ivanova, 1998) comprehensively studied fracture systems in nature and highlighted folds as one of the major geologic settings that produce fractures. Naturally occurring folds in reservoirs sometimes compound fracture analysis. It might not be clear whether the fractures formed before, during or after rock folding. Fractures formed during the folding process are expected to show stress orientations related to folding and are thus of primary concern in rock folding simulation. It could be argued that there are no numerical models that as"

Jan 1, 2015

By R. Scheepers

"Abstract -Mineral deposits and prospects of the Pan African Saldanian orogenic belt in the south­ western Cape Province South Africa, are reviewed. Despite the entire absence of operating base or precious metal mines in the area, this study has established at !east four metal associations that offer enticing exploration potential .The poly-phase deformed, low-grade metamorphosed volcano-sedimentary Malmesbury Group constitutes a complex, poorly understood supracrustal sequence that has been loosely subdivided into the Tygerberg, Swartland and Boland tectono-stratigraphic terranes by northwesterly trending fault zones. Syn- and post-tectonic granitoids of the Cape Granite Suite selectively intruded these terranes. Early S-types preferred the Tygerberg terrane whereas the later I-types dominate the remaining areas. Anorogenic A-type granites, however, occur in all three domains. Known metallization is directly or indirectly related to the intrusives, yet syngenetic deposits are conspicuously absent from the supracrustals. Four metal associations have been identified.•,Cassiterite-wolfrarnite (± Au, Cu, Mo, Fe-sultides) in quartz and quartz/aplite veins hosted by tourmalinized and locally greissenized S-type granite. Similar exo-granitic veins occur in proximal metamorphites.•,Juxtaposed disseminated, stockwork, breccia and vein style Cu-Mo-Fe-(Au)-sultide mineralization hosted by matie to intermediate intrusives of high K calc-alkaline, 1-type affinity.•,Cu-Mo-Au-sultides hosted by hydraulic breccia pipes, stocks and veins occurring in anorogenic A-type alkali feldspar granites and amphibole quartz syenites.•,Scheelite with minor Cu-Mo-sulfides and Au-associated with endo- and exo-skarns spatially related to I-type monzogranite, granite and alkali feldspar granite .The first three associations occur along the Yzerfontein-Helderberg-Zone, a 180 km lineament in the Tygerberg terrane, a zone exploited by syn-, late- and post-tectonic intrusives and their related mineralization. The fourth association is typical of the Boland terrane. The spatial and temporal relationships between the various metal associations is interpreted as the result of sequential intrusion of relative early high level S-type, followed by intermediate level I-type and finally anorogenic A-type granitoids during the evolution of a contracting continental margin arc and its inner arc. This plate tectonic setting suggests subduction in an easterly direction underneath the Kalahari craton. The spatial configuration of the various terranes at the present erosional levels is the result of rifting and significant differential vertical displacement following cessation of subduction, a terminal tectonic event possibly synchronous with intrusion of the A-type granitoids.Near surface preserved roof zones and cupolas of both S- and I-type granitoids in the Tygerberg and Boland terranes, respectively, render these areas extremely prospective for Sn, W, Mo and Au mineralization. The presence of intermediate to mafic volcanics, a diversity of calcareous lithotypes and favorable plate tectonic setting of the Malmesbury Group suggest potential for the thus far elusive VMS, MVT and Sedex base metal and minor precious metal deposits."

Jan 1, 1994

By George P. Demopoulos, Nima Parsi Benehkohal, Marianna Uceda

Lithium-ion batteries (LIBs) find wide range of applications from portable electronics to electric cars and stationary storage or renewable energy. LIB electrode fabrication is done through mixing the active material (Li-ion host) with carbon (conductive component) and polyvinylidene fluoride (PVDF), which acts as a binder. These components are dissolved in N-methyl-2-pyrrolidone (NMP) to form a paste which is then doctor bladed onto the aluminum current collector. NMP is a toxic chemical and the overall fabrication process remains costly. Efforts are made of eliminating NMP by (1) replacing the binder and (2) using a new fabrication method. Of particular interest among these new methods is electrophoretic deposition (EPD). Via the application of DC potential, particles in suspension can be electrophoretically deposited on different conductive substrates in a relatively fast rate rendering EPD feasible for industrial application. A key aspect for successful application of EPD is the formulation of a stable suspension. Within the McGill HydroMET group, we explore the potential of EPD in fabricating LIB electrodes having demonstrated its effectiveness in the case of P25 nanotitania/carbon anodes. The performance of EPD fabricated TiO2/C electrodes is compared to standard PVDF-based electrodes and shown to have comparable charge capacity. This method is now being extended to other electrode materials. In this paper an introduction to the EPD method will be made and subsequently its use in fabricating LIB electrodes will be described. The performance of the fabricated batteries is evaluated via galvanostatic charging/discharging and cycling tests.

Jan 1, 2016

By C. Prévost, V. Leclerc, R. Pinto, M. Ruel

"A buffer’s ability to dampen production variations is directly related to its size. Small buffers cannot handle large variations in production, resulting in production losses when their inventory is depleted or saturated. This paper presents a predictive control algorithm used to regulate the inventory in a buffer of limited size, subject to large production variations caused by an upstream batch process. The algorithm was designed to manage the acid flow rates in an acid regeneration process, servicing batch leach reactors at Rio Tinto Fer et Titane, in Sorel-Tracy, Québec. The objective was to increase production by reducing equipment downtime caused by imbalances in the acid tanks servicing the leach reactors. The controller attempts to maintain acceptable acid tank volumes by optimizing the leach reactors acid/slag ratio and reaction time as a function of anticipated acid needs, all while maintaining product quality.INTRODUCTION Some beneficiation processes in extractive metallurgy require processing bulk material in batches. Typical examples of metallurgical beneficiation batch processes are smelting, leaching, electrowinning, elution and carbon-in-pulp. These processes are often situated midstream in an ore beneficiation flow sheet and either receive or transfer ore to continuous processes. Batch processes, by their very nature, introduce large variability in the flow sheet, because they process large finite quantities of material at nearly periodic time intervals. In order to dampen variations in production, various buffers–tanks and stockpiles–are utilized to accumulate ore upstream and downstream of batch processes. A buffer’s ability to dampen production variations is directly related to its size (Phillis & Gumede, 2011). Small buffers cannot handle large production variations, resulting in equipment downtime when their inventory is depleted or saturated (Everett, 2010, Berton et al., 2013). Consequently, the batch equipment production rates must be adequately managed to minimize production losses, attributed to depleted or saturated inventories, while maintaining product quality. Algorithms that anticipate or predict future production variations are often utilized to regulate buffer inventories, subject to large flow rate variations (Salvo et al., 2002; Bonvin, 2013). This paper presents a predictive control algorithm used to maintain an acceptable volume in a spent acid tank servicing several batch leach reactors. The algorithm is implemented at the acid leach plant of Rio Tinto Fer et Titane, in Sorel-Tracy, Québec."

Jan 1, 2017

By Chris Rule

This paper tells the story of the rapid commercial application of stirred milling technology at Anglo American Platinum?s many Concentrators. The first stirred mill ? a 10 000 litre IsaMillTM; the largest at the time, was commissioned in late 2003. The project development work was presented at SAG 2001. This operation was ?proof of concept? and vindicated the decision to scale up the technology; allowing a rapid and extensive roll-out of mainstream regrind mills as well as several further flotation concentrate regrind mills, over the next six years. Currently 23 stirred mills are in operation with 64 MW of installed drive capacity ? this paper describes the projects? roll-out and the significant results achieved to date. Many operational problems have been solved along the way, some of these will be described. The introduction of the technology has seen a step change in metallurgical results and progressively decreasing operating costs.

Jan 1, 2012

By J. E. Udd, L. P. Geldart, B. B. Dhar

"Solutions for the stress distributions around simulated underground openings have been limited to calculations of boundary stresses for simple openings in which the boundaries may be expressed in mathematical terms. Studies involving circles, ellipses and ovaloids are re-ported in the literature.The stresses on the boundary of an opening and those at a distance from it in the medium are of concern to the engineer. The former may be related to the greatest concentrations of stresses encountered; the latter have a bearing on the identification of the ""zone of influence"" of the opening.Recent advances, in the form of a derivation for the stresses at a distance from an opening of elliptical shape, together with a solution derived previously for stresses in depth around ovaloidal openings, have been combined with computer programming techniques to provide complete solutions for a wide range of cases and variables. Some typical results which, it is hoped, may have some application to the design of underground openings are given herein."

Jan 1, 1970

By S. Bastola, Y. P. Chugh

"This research determines shear strength and stiffness properties of bedding planes and joints in the roof strata rocks within 7.5 to 9 m (25-30 ft.) overlying the Illinois #6 coal seam (within the pressure arch zone). A shear test loading device was designed into a 1.334 kN (150 t) Forney Compression Loading Machine to perform direct shear tests in accordance with ASTM D5607-08 “Standard Test Method for Performing Laboratory Direct Shear Strength Tests of Rock Specimens under Constant Normal Force”. The data were used to determine peak and residual friction angles and the dilation angle. A total of 49 bedding plane samples were tested, out of which 46 (36 intact and 10 relatively weak and loose) samples passed QA/QC procedures in accordance to ASTM D5607. Samples from eight (8) different bedding planes- shale/limestone (SL), shale/sandstone (SSs), shale/bone (SB), laminated sandstone (LS), shale/shale (SS), bone/bone (BB), bone/limestone (BL), and limestone/limestone (LL) were tested. The number of samples tested for each bedding plane were: SL- 11, SSs- 8, SB- 5, BB- 4, LS- 6, SS- 9, BL- 1, and LL- 2. Peak and residual shear strength values at 2.75 MPa normal stress range 1.06 – 6.26 MPa and 0.82 MPa to 0.82 – 4.14 MPa, respectively. The average normal and shear stiffness values are about 11.98 GPa/m and 3.11 GPa/m. Dilation angles are low (<10?) and negative in some cases. Angle of sliding friction values range from 9? to 42?. Joint Roughness Coefficient (JRC) values were less than 10.INTRODUCTIONRock mass may be defined as the total in situ rock medium containing bedding planes, faults, joints, folds and other structural features. Therefore, it is discontinuous and may have heterogeneous and anisotropic engineering properties. Upon creation of an excavation in a rock mass, bedding planes and joints are the most likely points of failure initiation. The failure typically occurs either in tensile or shear mode. Upon failure initiation stresses are transferred to the neighboring rock mass and the failure progresses until stability is achieved through equilibrium of stresses and strength. An example of this mechanism is development of the pressure arch. This study determined the shear strength and stiffness properties in shear and compression of bedding planes and joints in the immediate roof strata rocks within 7.5-9 m ( 25-30 ft.) overlying the Illinois No. 6 coal seam (within the pressure arch zone). Since such data are currently not available for Illinois Coal Basin mines, researchers and engineers have been using estimated values for design purposes. The immediate roof lithology in the proposed mining area consists of shale 0.62 m; Bone 0.09 m (0.3 ft.); Limestone, 0.10 m (0.33 ft.); Shale 2.37 m (7.9 ft.); and sandstone 0.55 m (1.83 ft.). The bedding plane samples were provided by a mine in south-eastern Illinois operating at a depth of about 180 m (600 ft.)."

Jan 1, 2015

By A. R. Barnes, N. Stubina

Increasingly, gold producers are forced to treat ever more refractory ores. While ores containing pyrite, arsenopyrite and carbonaceous material have been subjected to complete pressure oxidation (PDX) as the standard process for such ores, recent improvements in fluid bed roasting technologies have led to a resurgence of interest in roasting as a viable alternative. The lower capital and operating costs of roaster installations add further impetus to this trend. The Extractive Metallurgy Group at Xstrata Process Support operates four fluid bed reactors of various sizes which have been utilised on a large number of projects to treat highly refractory ores. Preliminary mineralogical modelling of both the physical and chemical aspects of the roasting process and subsequent testing under carefully controlled conditions has allowed clients to obtain gold recoveries approaching or matching those achievable by PDX. The flexibility of the units to operate in various modes- " bubbling bed", circulating bed, two stage, sub-stoichiometric and combinations of these, and the range of sample sizes accommodated, from a few kilograms to a few tons, has enabled XPS to accommodate clients with a wide variety of gold bearing refractory ores from all over the world. This paper outlines the key challenges of fluid bed roasting of refractory gold ores, describes the methodology used to design the testwork program and provides some results from select test campaigns.

Jan 1, 2011

By J. W. Coetzee, H. E. Deist

Carbon-in-pulp (CIP) and Carbon-in-leach (CIL) processes are used extensively in the gold mining sector to recover aurocyanide from solution. This paper discusses the modelling of these operations, using various simplifying assumptions, in order to simulate the effect of changing operating conditions on the dynamics of the system. It is assumed that the adsorption and leaching rates are a function of concentration difference between the source phase and recipient phase. The simulation was set up using Matlab&apos;s Simulink interface. Plant variables are solved using a medium scale Newtonian search algorithm in Matlab, where the differences between the actual and predicted plant outputs are minimized on a continuous time-line.

Jan 1, 2005

By S G. Bergdahl

Underground mining in Sweden is today characterized by mechanization and automation, owing to the rising cost of labour. Drilling in drifts and tunnels is still essentially done with jackleg drills, but rigs wh1ch make it possible for one man to operate two or more drills are now frequently used. Large jumbos for longhole drilling, with two drills operated by one man, are used, especially in sub-level caving. A special drill-rig for drilling through overburden and blasting without removing the overburden has been successfully used in canals and also in ports, where blasting is per-formed under water. The increased use of mining methods based upon long blastholes is a result of the development of equipment for drilling long straight holes. The most common mining method in Sweden is sub-level caving. Extensive research, with model tests, has been carried out in order to determine suit-able dimensions of drifts, sub-levels and drilling patterns. The results have been tried in practice and have given increased yield and less waste rock in hoisted ore.

Jan 1, 1963

By Robert Voisey, Robert J. Spencer

"LynnGold&apos;s MacLellan Mine is located about 8 km south east of Lynn Lake immediately to the east of the Keewatin River (Fig. I). The property is accessible by an all-weather road, leading north from the provincial highway 391, which links with the Town of Leaf Rapids and the City of Thompson to the south.The ore body, as outlined in the original feasibility study, is expected to produce in excess of 9.3 x IQ6 gm of gold and silver over the next 5 years. However, the deposit is open to depth and exploration is continuing on and around the main zone and the many satellite deposits.The start of construction of the MacLellan Mine and mill was scheduled to phase in with the closure of the Fox copper-zinc mine located 48 km west of Lynn Lake. The majority of the employees from the Fox Operation were either employed at the MacLellan Mine or relocated to Sherrin&apos;s Ruttan Operation.GeologyThe MacLellan gold ore deposit is located on the northern section of the Lynn Lake Greenstone Belt known as the Rainbow Trend. This Trend is a 40 km gold bearing rock sequence extending both east and west from the MacLellan Mine. The southern section of these two east-west trending structures is known as the Johnson Shear, this is also gold bearing."

Jan 1, 1990

By C. Caners

One of the main uses of fossil fuels is in the transportation sector, leading to environmental consequences such as climate change. In order to move towards a more sustainable energy infrastructure, a transition must begin from fossil fuels to renewable fuels, derived from e.g. biomass. One means of facilitating this transition is to develop reforming technology that can extract hydrogen from a suitable fuel that is either fossil fuel or renewable in origin. The hydrogen would be feed to a &apos;fuel cell&apos; engine that would power the car, truck or bus. One reforming technology that is attractive for automotive applications is autothermal reforming (ATR). Autothermal reforming is the combination of steam reforming and partial oxidation, whereby a portion of the fuel is combusted using a sub-stoichiometric amount of air, and the resulting thermal energy drives the more desirable steam reforming reaction. ATR is attractive for fast start-up, rapid load following and ease of control. ATR also has the benefit of smaller volume and fewer peripheral requirements as compared to other reforming technologies. Recently, a bench-scale gasoline autothermal reformer (ATR) was constructed and tested. This ATR employs a novel design, consisting of three concentric annuli in order to promote heat transfer from the partial oxidation reaction to the steam reforming reaction. Concurrently, a CFD based model (FLUENT) of the ATR that considers the geometric complexity of the reformer was validated. In spite of the use of simplified kinetics, the model predicted well the observed trends in temperature and overall performance. This paper will discuss the use of the model to improve the design of the ATR. The impact of various system parameters upon performance will be investigated along with alterations in the geometry of the ATR. The various tradeoffs in performance and system volume/size will be highlighted in the context of a fuel cell power system.

Jan 1, 2005

By Arthur Notman

For the period January 1st, 1942, to January 1st, 1946, the American Bureau of Metal Statistics records the gold production of the world as 118,788,000 fine ounces. If we include 1946 at the same rate as 1945 (26,- 590,000), we arrive at a total of 145,378,000 fine ounces in the past five years . Included in these figures are estimates of Russian output at 4,000,000 ounces per annum for the five years, and 1,300,000 ounces per annum for Korea and Japan. The remaining 120,000,000 ounces represent the aggregate production from official reports of the other gold producing areas of the world, with the exception of the 1946 figures, as noted above. At $35.00 per fine ounce, this represents $5,188,230,000. According to the reports of the Federal Reserve System of the United States, on December 31st, 1941, the monetary gold reserves of the United States were $22,736,- 600,000 (at $35.00 per fine ounce) , while on October 31st, 1946 (latest available) , they had fallen to $20,402,000,000, a decline of $2,334,600,000. Adding this decline to the value of the new production for the five years, we have a total of $7,522,830,000, which has been absorbed by the rest of the world since Pearl Harbour, a rate of absorption of over $1,500,000,000 per annum. This has taken place at a rime when the advocates of purely managed currencies had convinced many people that gold performed no really essential function in the world&apos;s economy, and that we could get along perfectly well without it. It was pointed out that gold could not be eaten, it could not clothe our nakedness, it could not shelter us from storms, and, therefore, it was a non-essential, even though it could be used to settle international balances of trade. Apparently, the world as a whole still regards it as preferable to the paper promises of governments, however sound, relatively, they may appear. Actually, we have no way of measuring the true strength of this feeling, because the principal governments of the world have made it legally impossible for their citizens to own gold, except in the form of ornaments.

Jan 1, 1947

By P. B. Demarsh

"Location: - On highway 59, 17 miles east of Val d 10r near junction of Montreal highway in Northwestern Quebec.Life; - Started production 1952, ceased 1965.Ore: - Pyrite, chalcopyrite and small amounts of free gold and goldsilver tellurides in narrow quartz-carbonate-tourmaline veins in granodiorite. Specific gravity 2, 70.Capacity: - 700 tons daily Bevcon ore supply, l 000 tons daily when custom ore available.Assay: - Heads 0 .140 oz. per ton; tails 0. 009 per ton; extraction 92.5%.Grind: - 75% minus 200 mesh at 700 tons; 68% minus 200 mesh at 1000 tons. Detention time 28 hours and 21 hours respectively.Treatment: - Cyanidation process.Reagents: - Per ton. Aero Cyanide (NaCn) 0, 50; crushed unslaked lime 1. 75; zinc 0. 03; litharge 0. 10; steel consumption 2. 25.Water: - Pumped from land-lock spring fed lake l 1/2 miles distant.Cost: - Per ton. Crushing 0. 13; grinding 0 .32; filtration 0. 07; cyanidation 0.14; miscellaneous 0.29; total 0.95.Power: - Hydro-electric, 25 cycle, 12, 000 volts reduced to 550 volts.Labour: - Predominantly French Canadian, nucleus English Canadians.Tailings: - Impounded low lying pond.Personnel: - 15 including supervision.Flow sheet: - Canadian Mining Manual l 9 5 6 .Building: - Wood truss construction: 3/ 4 in. siding, ten test and 1/ 4 in. transite outside. Corrugated galvanized iron roof. Ground level foundations. Internal self induced heating. Wood stave tank equipment."

Jan 1, 1966

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By Roy O. Ifill, W. Charle Cooper, Alan H. Clark

"A detailed study of the compositional relationships of the Uand Th-bearing minerals in Elliot Lake uranium ores has been conducted, particularly with regard to uranothorite, which clearly plays a critical role in hydrometallurgical processing. Application of the rotating disc progressive-leaching technique to individual mineral grains and intergrowths of known compositions has defined for the first time the solubilization behaviour ofthe minerals in question.In descending order of leachability, regardless of leaching conditions, the phases are: uranothorite, uraninite, and monazite. Inclusions of secondary uranothorite enhance the dissolution kinetics of uraninite, which exhibits a complex dissolution mode. U-rich uranothorite dissolves more readily than Th-rich. Monazite is soluble in HJ)04 and HCI solutions only at temperatures exceeding 85°C. Consequently, it is deduced that the 15% to 20% of thorium not leached from the ore is lost both as monazite and as uranothorite inclusions locked in monazite which persists to the tailings. INTRODUCTIONThe importance of precise information on the mineralogy of ore and gangue constituents for the optimization of metal recovery in hydrometa Uurgical processing has been recognized for some years (e.g. Burkin, 1969), and numerous investigations integrating mineralogical studies and experimental leaching have been reported for ores of gold, nickel, copper and uranium (see summary by Henley, 1983). The complex mineralogy of uranium ores hosted by Precambrian pyritiferous, quartz-pebble, conglomerates has prompted particular attention in this regard (e.g. Liebenberg, 1956; Liebenberg and Taverner, 1958; Feather and Snegg, 1978). In the great majority of documented studies, however, petrographic examination has been followed by bulk leaching, an approach which, although providing valuable information, does not permit precise definition of the evolution of mineral dissolution processes. The authors contend that experimentation involving the step-by-step leaching and mineralogical study of ores is more likely to reveal the actual dissolution events which control the release of metals and, hence, may better define the optimal conditions for hydrometallurgical processing. Such studies (e.g. Hausen, 1983; Horlick et al., 1981) in addition lend themselves to the prediction of changes in the leaching behaviour of ores in which one or more mineralogical feature is subject to modification, a common characteristic of mineral deposits."

Jan 1, 1989