Search Documents

By D Asahina, T Endo, H Hosono, T Takemura

Changes in the stress field around faults due to the excavation of underground space or the extraction of underground resources induce fault reactivation. To understand the mechanism of fault reactivation, it is important to observe the deformation and sliding processes of the asperities, which is regionally contacted areas at the fault planes. In the laboratory, triaxial compression tests are commonly conducted to reproduce the stress conditions around faults and study their mechanical behaviours. The conventional measurement devices for triaxial compression testing (eg load cells, local deformation transducers, and piezoelectric sensors) uses sensors to measure changes in the physical properties of rocks, but the direct visual information for the sample condition inside the pressure vessel is limited and can only be estimated from the sample after the experiment. We recently developed a direct visual measurement system to observe the slip behaviour of rocks from the inside of the pressure vessel of a triaxial test apparatus. This paper introduces this visual measurement system and presents some preliminary experimental results. The visual measurement system consists of a steel housing with a built-in commercially available digital camera. The triaxial compression tests were conducted to visually observe the sliding behaviour of the pre-cut specimens and to measure its behaviour through the digital image correlation (DIC) method. The captured images and the DIC results show the displacement field of the specimens for different confining pressure. We verified the sliding behaviour and the failure at/around the triangular asperity under at different confining pressure.

Nov 29, 2022

By G Simpson, S Dressler, A E. Levett

Tailings storage facilities often represent a mining operation’s most significant liability, posing serious environmental, social and safety risks. Almost all mining operations dispose of wet tailings (Valenta et al, 2023), which represents a risk of failure due to the potential for a rapid strength reduction of the unconsolidated materials leading to static liquefaction and subsequent dam wall failure. As a waste stream, tailings disposal, decommissioning and relinquishment aim to be inexpensive processes, ruling out many highly engineered solutions. Advantageously, tailings consolidation does not need to be immediate, opening the door for relatively passive, inexpensive consolidation methods that aim to gradually increase the strength of tailings over extended periods (ie years). In this paper, we present the prospect of novel in situ tailings stabilisation, learning from studies that have investigated the most erosion-resistant landforms on Earth.

Aug 2, 2023

By E Holloway

The optimisation of an open pit mine can be broadly split into two stages, the first being the ultimate pit optimisation (and subsequent stage designs), and the second being schedule optimisation. Macroeconomic uncertainty clearly impacts on both however interrelationships do also exist. Generally, the opportunity exists for the ultimate pit to be revised during each planning cycle, however when this reprieve is removed the uncertainty for the underlying business increases. As one example, the introduction of an in-pit waste dump can be seen to significantly limit the option to revise the ultimate pit. When in this situation there are two potential risks that present: (i) the long-term price used for the ultimate pit selection is optimistic, and too large of a pit is selected resulting in waste being mined which uncovers material not of a significant value to deliver a profit; (ii) the long-term price used for the ultimate pit selection is pessimistic, too small of an ultimate pit is selected, and ore of realisable economic value left behind. Both of these outcomes are risks and as such can be assessed and quantified. CITATION: Holloway, E, 2018. Incorporating economic variability into a strategic planning framework, in Proceedings Complex Orebodies Conference 2018, pp 88–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By M Nehring, M Kizil, P Knights

Mining and beneficiation can be described as sequential processes of separation of valuable minerals from waste. There is a great deal of interest in how the industry can be more effective – and efficient – with these processes. In particular, many mining companies are looking towards digital technologies to improve precision mining practices; that is, the targeted identification and separation of valuable ore from waste during the mining process. Greater precision will help unlock the value in many complex orebodies that are currently considered Tier 2 or 3 deposits. CITATION: Knights, P, Kizil, M and Nehring, M, 2018. Selection of precision surface mining methods for complex metalliferous orebodies, in Proceedings Complex Orebodies Conference 2018, pp 31–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By P M. Cepuritis

In hard rock mining, large-scale bulk mining methods such as block or panel caving (BC/PC) and sublevel caving (SLC) typically generate significant surface deformations such as subsidence. Surface deformations need to be considered in the project evaluation and planning stages of cave mines, for example, planning and location of critical underground mine planning infrastructure such as portals, haulage and vent shafts, access roads, or potential damage to existing infrastructure, changes to surface water management, waste dump, stockpile and tailings dam stability, and environmental impacts. Assessing the impact and risks associated with subsidence is a key component in robust mine planning and operations management.

Nov 29, 2022

By M Alston

Organisations’ incident classification processes are plagued by the overclassification of events, often leading to excessive workloads and suboptimal outcomes. This presentation addresses the pressing need to rethink how incidents are classified to maximise organisational learning and minimise systemic risk. A major issue in the current incident classification landscape is the tendency to classify events at high levels, overwhelming organisations with investigations they cannot efficiently handle. This results in inadequate risk reduction and learning opportunities. The link between injury classification and investigation methods further compounds these problems, creating unnecessary administrative clutter. Challenging the misconception that every event, no matter how minor, requires a comprehensive investigation, this presentation advocates for a shift in perspective. The key recommendation is to decouple injury classification and risk matrices from the decision-making process regarding what and how to investigate. Instead, the emphasis should be placed on identifying opportunities for organisational learning and risk reduction. Organisations can streamline their incident management processes by adopting a more pragmatic approach that aligns incident classification with the organisation’s investigation capacity. This transformation focuses on achieving meaningful outcomes, enhancing safety and improving performance. This presentation provides an innovative process for organisations to revamp their incident classification practices, enabling them to harness the full potential of incident data for learning and risk mitigation. It highlights the importance of aligning incident classification with the opportunity for organisational learning, ultimately leading to more effective incident management and enhanced safety outcomes.

Apr 16, 2024

By K Baker, J Purtill

One of the key challenges for the mining industry globally is the rehabilitation of mine waste, and Queensland is no exception. Out of pit waste structures including waste rock dumps and tailings storage facilities, create novel landforms which require ongoing maintenance and pose risks to the environment and sometimes to communities. Where multiple mines co-exist, such as parts of Queensland’s Bowen Basin, individual mines can often be constrained by adjoining operations. This presents opportunities for broader rehabilitation strategies to be considered, more than the current single mine focus, that may provide better environmental outcomes for a region. Given recent global disasters involving tailings storage facilities, and our team’s endeavours to drive Queensland to achieve leading practice in mined land rehabilitation, we are exploring the potential to maximise in-pit tailings disposal opportunities for coalmines through shared waste management strategies. A shared waste management strategy is where two (or more) mines, owned by different companies and operated under different environmental permits, transport tailings from one mine to the other in close proximity, for disposal in a disused pit. This would reduce the number of waste structures to be built, operated, rehabilitated, and managed in perpetuity. Our objectives are to identify and remove barriers to tailings transfers between sites to:  minimise environmental risk  minimise long-term liability of managing mining waste and associated structures  support improved outcomes for the local community. To determine the scale of coal waste disposal practices in Queensland, internal data and publicly available imagery was analysed by the Department of Environment and Science in 2022. Approximately 6500 ha of land in Queensland is utilised for coalmine tailings storage facilities or codisposal areas, with ≈ 3700 ha of this being out of pit.

Aug 2, 2023

By B Liu, W J. Zhang, S Saydam, B Li

Rock bolts are commonly used to reinforce ground in underground mining and civil tunnel environments. Rock bolts serve two main functions: i) they suspend large, loose blocks of ground, and ii) provide a protective pressure arch to restrain the deformation in an excavated void. Automated and precise tracking of rock bolt positions can assist with the operational success of ground support by reducing the amount of labour required in current manual practices. A point cloud is a large list of x, y and z coordinates in three-dimensional space, that when visualised, show a precise 3D representation of a physical environment. Point cloud data can be collected using accurate LiDAR scanners. These scanners can be mounted on a stationary tripod or on a moving vehicle. A key way point cloud data is used is in the bolt detection project being completed in conjunction with UNSW Sydney, which aims to provide an automated location of underground rock bolts from LiDAR scans. The immediate challenge with identifying rock bolts is that they constitute a very small portion of the data set amounting to approximately 0.01 per cent of some of the collected civil tunnel data. The process of detecting rock bolts from point clouds therefore requires a quick elimination of large background data while still preserving the bolt data. A further challenge is that the geometry of underground environments can often be very complex and non-uniform. To overcome these challenges, a two-step coarse to fine deep learning approach is taken. The first step is a coarse background elimination step aimed at removing as much of the background data as possible. The second step is a finer classification method, which uses deep learning to further segment the bolts from the remaining background. Additionally, a computer vision module is being implemented, which is expected to increase the detection rate by adding another dimension to the training data set.

Nov 29, 2022

By D Head

IonicRE acknowledges within our mining industry, there is a common belief that workplace health and safety, often referred to as safety, is just a matter of ‘common sense’ – something obvious and easy. However, at IonicRE, we hold a different perspective. We understand that safety is far from easy. We recognise the need to emphasise the importance of understanding and conveying the inherent difficulties of working safely. We are committed to implementing processes that support individuals in achieving our safety objective of eliminating fatalities and permanently disabling injuries. To build resilience and sustainability into safety performance, we draw parallels with the principles underpinning sustainable and exceptional production performance. Achieving sustainable safety performance demands effective leadership, meticulous planning, adept management, genuine care and unwavering commitment. We’ve leveraged various tools and techniques, such as DISC theory, Maslow’s hierarchy, process control, Kaizen, Six Sigma and Kirkpatrick’s 4 levels, among others, to facilitate this improvement. There methods play a pivotal role in developing a Safety Blueprint for enhanced safety performance. This paper provides an overview of IonicRE’s Safety Blueprint, a strategic framework for developing our safety capability. Our capability is underpinned by three key pillars. Firstly, a comprehensive risk management approach is imperative, encompassing the understanding of hazards, the identification of threats to our people and the associated risks. Secondly, it entails providing and enforcing accountability to sustain our safety capability. Lastly, it involves constructing an effective defence system against threats and harm. Implementing these pillars requires a meticulously devised change process. Anticipating resistance and potential setbacks, we underscore the importance of having the right people and a wellcommunicated vision for safety at IonicRE. A Safety Blueprint serves as a detailed plan outlining the path toward a future goal. At IonicRE, we contend that safety in the mining industry has generally lacked a coherent and effective Safety Blueprint – a comprehensive plan to navigate the journey toward a destination. Drawing parallels with NASA’s detailed plan for landing a man on the moon safely, we question why, as an industry, we cannot similarly eliminate fatalities. While progress has been made in the last century, we must not wait another 50 years to eradicate fatalities from our industry. Examining Safe Work Australia data from 2008 reveals that 47 per cent of mining fatalities result from vehicle activity and 40 per cent stem from individuals being struck by an object. As of December 7, 2023, seven lives have been lost in the mining industry in Australia this year, indicating a stubborn trend mirroring 2022, with limited improvement over the past 25 years. These incidents are not isolated or unexpected. We understand the hazards and controls, yet fatalities persist. IonicRE considers that the mining industry stands at a critical juncture – do we accept a plateau in mining safety performance, or do we rethink our approach? At IonicRE, we are thoroughly reassessing the hazards that threaten our people, systematically redefining effective risk control measures and establishing a robust framework to hold individuals accountable for the effective implementation of the control measure.

Apr 16, 2024

By N Udugampola, d A. Seneviratne, X Ai, B Li

With the evolution of mining technology, wireless mesh networks using low-power, long-range technologies such as LoRa are increasingly utilised in underground mining operations. Efficient deployment of wireless nodes in such mesh networks necessitates understanding radio wave propagation behaviour in underground mines. While existing propagation models either remain theoretical or apply only to basic geometric shapes, we propose a practical approach to analyse radio wave propagation behaviour in underground mines using ray tracing simulations with reconstructed 3D models of targeted environments. Our method validated using a set of corridors as a substitute for underground mine environments, involves constructing a 3D model using SolidWorks from LiDAR scans of the environment and performing wireless transmission simulations using the MATLAB ray tracing toolkit. Our simulation model is also fine-tuned by calibrating the raytracing parameters based on real-world LoRa transmission experiments in the actual environment corresponding to the 3D model. This method offers a practical solution for optimising wireless node placement in underground mines, facilitating efficient network deployment while reducing the need for extensive physical testing of radio wave transmissions.

Sep 1, 2024

By D Joshi, J Rostami, M Karakus, A Eustes

The first target of mining activities on the surface of the moon is to find and extract water from the icy regolith on the moon. A test drilling unit was designed and fabricated under a NASA Early Stage Innovation (ESI) grant. A high-frequency data acquisition system was used to record drilling responses at 1000 Hz. Parameters like weight on bit (WOB), torque, rev/min, rate of penetration (ROP), mechanical specific energy (MSE), field penetration index (FPI), and the uniaxial compressive strength (UCS) were recorded for 40 boreholes in the analog samples made of regolith simulant and specialised cement. Development of the AI system and machine learning (ML) algorithms for analysis of data to evaluate strength and hence water content of icy regolith required a large data set. In this case, the data set comprising of more than one billion data points recorded while drilling into various analogue samples and cryogenic lunar formations to optimise power consumption and make bit wear adjustment during drilling operations. The tests were also repeated in the samples of icy regolith at various water content at -190C to verify the ability of the algorithms to analyse the data and to estimate the strength of the frozen formation and hence water content. The paper will discuss the objectives and methodologies used in the project and reviews the testing program and the machine learning (ML) algorithms ability to identify various formations along the exploration boreholes.

Sep 1, 2024

By P Martin, A Somarin, S Bailey

Field-based research was conducted to investigate the performance of field portable X-ray fluorescence (FPXRF) in the analysis of reverse circulation (RC) drill chips in iron ore exploration. For years, FPXRF has been considered unsuitable for iron ore exploration due to the limitations of the elements it is capable of analysing for, in particular its inability to measure light elements (Mg, Al, Si, P, S). With the advent of the use of silicon drift detectors (SDD) in FPXRF, light elements are now measurable elements. However, doubt over the appropriate use of this new technology still exists due to the absence of reliable comparative field data. These doubts concerned the ability of the FPXRF data to correlate strongly with the laboratory assay of the same samples. It was believed that inconsistent grain size and other variables not being controlled would contribute greatly to this perceived unreliability.We tested RC chip samples on-site in the Pilbara, with the portable Thermo Scientific Niton XL3t X-ray fluorescence (XRF) analyser for a range of elements including Fe, Mn, Al, Si and S and then compared the results with laboratory assay data. A strong correlation indicates that the FPXRF results are reliable. Furthermore, to show the effect of simple sample preparation, we also analysed pulps of the same samples in the same way.The correlations were good for all of the elements of interest for the RC chip samples (R2 values between 0.82 and 0.9), and excellent for the pulps (R2 values between 0.89 and 1). The results also showed a direct correlation between sample preparation and improved quality of results with the FPXRF. This indicates that FPXRF can produce data from unprepared RC chips for Al and Si that, when compared with laboratory assays, is reliable for a field application in drilling and grade control. CITATION:Somarin, A, Martin, P and Bailey, S, 2013. Non-destructive analysis of diamond core for light elements using Niton field portable x-ray fluorescence, in Proceedings Iron Ore 2013 , pp 117-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By R H. Yoon, M Gupta, A Noble, K Huang

Froth flotation is the most commonly used separation technology in the mineral industries. Given the complexity of the pulp and froth phases as well as the multitude of operational parameters that influence flotation performance, purely fundamental models with strong predictive capacity are limited. As a result, accurately modelling modifications to an existing flotation circuit are challenging, particularly when using empirically-derived models from a different operating configuration. Despite these complexities, a recent publication by the authors (Huang et al, 2022) has shown that flotation rates can be accurately predicted from a first-principles model that incorporates hydrodynamic parameters (eg pulp density, superficial gas velocity, feed flow rates etc), surface chemistry parameters (eg contact angle, zeta potentials and surface tension), and size-by-class liberation data. Circuit simulations using this model were shown to be effective in predicting experimental graderecovery curves from the size-by-class mineral liberation matrix. Since the model is derived from fundamental characteristics of the flotation system, it can be used to simulate alternative circuit configurations with varying degrees of recycle. Conventional flotation circuits are operated in a closed-circuit configuration by routing the cleaner scavenger tails (CST) back to the rougher feed to provide an additional opportunity to recover the slow-floating particles. This widely-used flotation strategy has been under constant debate, and several researchers have provided evidence that open circuit configurations provide higher separation and better circuit control (Konigsman, 1985; Bulatovic et al, 1998; Thompson, 2016). Recently, Finch and Tan (2021), used linear circuit analysis to show that open circuit configurations have a fundamental advantage when stage recoveries are high. Given the limitations of these prior studies, the objective of the current work is to further evaluate the merits of the open circuit configuration through a detailed circuit analysis and simulation study incorporating the first principles model described above.

Aug 24, 2022

By S Carr-Cornish, K Moffat

Social licence to operate is developed and kept through managing both operational impacts and the relationship between local community and company. However, CSIRO research has demonstrated that in determining how accepting community members are of a mining operation, relational factors, such as procedural fairness and trust, are much more important than operational impacts, such as impacts on employment and the environment (Moffat and Zhang, 2015). Companies seek to develop relational factors through their engagement with local community; such engagement has many aspects, including, initially identifying stakeholders and positioning the company as part of the local community (Lacey et al, in prep; Thomson and Boutlier, 2011). These relational factors involve the social identities of people living in the community. Social identities are a part of people that shape their beliefs, based on their connections with various groups in their lives (Hogg et al, 2004).An engagement process, intentionally or not, inevitably interacts with the social identities of stakeholders (Crane and Ruebottom, 2011). For example, traditionally, at the very beginning of engagement processes, community members are assigned to categories using conventional stakeholder mapping and categorisation methods, often based on assumptions about stakeholders’ interests, which equates to assumptions about stakeholders’ social identities (Colvin, Witt and Lacey, 2016; International Council on Mining and Metals, 2012). Yet, there has been limited empirical inquiry into whether such categories reflect the social identities of stakeholders and if there is a bearing on relational factors, including, the perceived fairness of consultations and trust in mining companies (Crane and Ruebottom, 2011). Also at this time, companies commonly seek to create a presence in communities, for example, joining Chambers of Commerce and participating alongside community members. Again, there has been limited empirical inquiry into whether community members and companies identifying with the same overarching group and thus sharing aspects of social identity, influences relational factors (Crane and Ruebottom, 2011). In this study, we examined the effects of changing aspects of social identity by changing how stakeholders were identified and companies were positioned, on how stakeholders’ perceived a new mining operation, specifically how they perceived the procedural fairness of the proposed consultation process and trusted the company, two factors that underlie a company’s social licence to operate.CITATION:Carr-Cornish, S and Moffat, K, 2016. Out of the box – the power of social identities in engagement processes, in Proceedings Life-of-Mine 2016 Conference, pp 180–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By K White, C Ferguson, M Harding

Understanding watercourses and river processes at a landscape scale is vital for managing risk to mining infrastructure and operations as well as minimising future environmental impacts beyond the life of the mine. Recognising this, Iluka Resources Limited engaged Alluvium Consulting Australia to identify and characterise watercourses across several neighbouring mineral tenements in the Eucla Basin, South Australia (Alluvium, 2013, 2014a, 2014b). The objective of the studies was to inform planning for risk management during mine planning and operation and appropriate landscape rehabilitation for mine closure.Mining operations in the area are by open cut extraction of mineral sands. The extracted resource is processed on-site before leaving the site for export. Several pits are to be developed in stages with simultaneous backfilling and surface reinstatement. Mining is initially taking place in the Jacinth tenement, where up to 100 km of watercourses may be directly or indirectly impacted (refer to Figure 1).The total study area (shown in Figure 1) is approximately 330 km2 and spans three smaller areas that were the focus of separate investigations during mine planning.CITATION:Ferguson, C, White, K, Harding, M and Hardie, R, 2016. Landscape-scale assessment of watercourses in remote arid South Australia to inform mine planning to mine closure, in Proceedings Life-of-Mine 2016 Conference, pp 200–204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By J F. H Thompson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Mineral exploration and mining are challenging businesses. Remote and at times harsh conditions have always made it difficult for exploration, but modern explorers also have to deal with cover, numerous technologies, an explosion of data and critical early community engagement. Mining deals with the reality of moving and breaking thousands of tonnes of rock each day to extract what can be a very minor component of economic value, and, furthermore, society expects that this will be done in a clean and sustainable manner. The exploration and mining challenges appear disparate, but they are intimately related.Although not widely appreciated, both exploration and mining have a long tradition of innovation. Over the last 50 years, major step changes in exploration have resulted from radical advances in our understanding of ore forming processes, new geophysical, geochemical and remote sensing technologies, and new ways to integrate and interrogate data. Over a more extended period, close to 100 years, mining has developed bulk surface and underground methods, selective extraction through flotation and leaching and global positioning system–geographic information system control systems that collectively facilitate mining at a massive scale. And yet, in spite of these successes and the boom that we have enjoyed in the last ten years, the industry is under pressure and the need for innovation and change is paramount.The major drivers for innovation are the need for increased quality in discoveries and mines and the need to interact effectively with communities and jurisdictions such that the benefits of quality mines are recognised and enjoyed widely.We are still making new discoveries around the Pacific Rim and elsewhere, but many argue that the quality – grade and accessibility – of these discoveries is decreasing. The net result is that explorers are delivering resources and reserves for development at lower grades and with higher capital and operating costs than current operations. For mining, the increasing age of many existing operations contributes to increasing costs, which, when combined with decreasing cut-offs and lower grades, also results in declining quality. The combined picture does not look good.Just as the pressure to improve performance and margins in the face of declining inputs increases, we are simultaneously faced with increasing societal demands for improved environmental performance and sustainable practices. This is most apparent at the local, community level, where opposition ultimately leads to delays or even cancellation of new projects. Quality is again the issue – quality of the initial and ongoing engagement and quality of the proposed mine in terms of environmental and economic performance.CITATION:Thompson, J F H, 2015. Exploration and mining – the need for innovation , in Proceedings PACRIM 2015 Congress, pp 45–48 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By A Cornelius, P Connor, S Fraser

Iron ore mining is a major source of export income for Australia. However with the decreasing reserves of high-grade, low-phosphorus hematite ore, there is mounting pressure to provide consistent mineralogical ore grade. Enhanced 3D characterisation and modelling are crucial to respond to these exigent requirements. To tackle this problem a revolutionary mine-based, imaging system (based on Visible Near Infrared û Short Wave Infrared reflectance spectroscopy û VNIR-SWIR) has been developed. This innovative, CSIRO-built prototype produces mineralogical maps that will have a major impact on ore grade characterisation. Australian iron ore companies will benefit immensely by pioneering this emerging and unique mining technology. The significance of VNIR-SWIR reflectance spectroscopy is well demonstrated with field portable spectrometers and airborne hyperspectral systems. At the mine-scale level, this newly developed imaging system will allow accurate and objective mineralogical mapping of mine faces and benches with very closely spaced sampling. These spectral mineral maps will improve deposit delineation and bring accurate and objective ore grade characterisation that will minimise drilling and enhance ore recovery. This will in turn lead to cost saving and better long-term block model planning. This system will also improve safety for mine geologists in providing mineralogical information at a distance, avoiding the need for any close contact with the mine face. The mine imaging concept is a logical response to the industry need for automatic and objective tools for sustainable and future mining practices.

Jan 1, 2002

After many years of studying the rock mass gravitational flow phenomenon, it is well known that moisture conditions may change the mechanical properties of the caved and broken material, causing different problems at drawpoints. One specific problem, perhaps one of the most unpredictable and uncontrollable, is that of mudflows (also known as mud rushes). The aim of this paper is to show how to establish optimal extraction rates at a drawpoint in order to avoid the closure of that drawpoint due to the high risk associated with having high-technology automated loaders working in the production level of panel cave and block cave mines prone to mud flow events. This optimisation should take into consideration critical restrictions related to mine planning, such as the need to reach the planned production. It is also important to consider the correct design of surface (in the subsidence zone) and underground drainage systems to prevent groundwater or rainwater entering muck piles, filled stopes, galleries or open cuts. With these considerations, and keeping in mind other factors that should be included in a sensitivity analysis of variables, it is possible to find a correlation between the percentage of extraction from a drawpoint and the possibility of occurrence of a mudflow. Finally, this paper proposes different draw strategy techniques in order to mitigate potential mudflow issues on a caving production level.

Sep 26, 2011

By G B. French

Post a serious heating event underground, and at the direction of the State Mining Safety Authority, a mining company needed to demonstrate the use of cutting-edge technology to mitigate future events. Yokogawa were contracted to provide a turnkey solution to help the mine achieve this objective. The solution was to use a fibre optic-based Heat Detector that will allow entry into and around the mine considering the potential volatility of the environment, also the need to redeploy as mining activities moved underground and more boreholes are added. Industrial strength fibre optic cable and a robust connector system was chosen to achieve this goal and give the customer the ability to send cable down boreholes of up to +1 km and continuously monitor the temperature ofunderground roadways. Being able to re-deploy the cables into different boreholes and link borehole temperature measurements gave insight into all areas on the mine. The machines deployed on-site were the Yokogawa DTSX1 heat detector incorporating the Ramen Backscatter principle. Being of a robust construction and a low power consumption device, it was easily included into the portable monitoring trailers designed by the customer and built locally.

Oct 12, 2022

By D Stephenson, N R. Steward

“TerraFlowingTM” is a dewatering process that addresses both the value proposition of Tailings as a Resource™, and the safe storage of tailings. “TerraFlowingTM” incorporates two stages of cyclone dewatering followed by centrifugation of the final dilute tailings stream. In this process three dewatered tailings streams are produced; a primary cyclone underflow, a secondary cyclone underflow and a centrifuge pulp. These three streams can be combined, or used, in various configurations to achieve different outcomes. The ability to vary the cyclone and centrifuge operations and configuration enables this process to deal with tailings feed variations in particle size distribution and mineralogy and deliver consistency, or design variations, in particle size distribution, tailings solids concentrations and recoveries. Water recovery can be up to 85% of the total water in the tailings with a stackable final tailings product achieved if the three tailings streams are combined in the maximum solids concentration configuration. The primary cyclone can be operated to deliver a particle size distribution suitable for tailings storage facility embankment construction or alternatives such as concrete structures or shotcrete for support. The secondary cyclone underflow and centrifuge pulp is suitable for beaching deposition within the tailings storage facility.

Jul 1, 2021