Search Documents

By C A. Foss, K Leslie, C Arnold

Magnetic susceptibility measurements provide rapid, non-destructive testing of drill core, but cannot directly map magnetite and/or hematite content. Combined magnetic susceptibility and magnetisation measurements provide much more diagnostic information and, with sparse calibration constraints, are able to quantify magnetite and hematite concentrations and potentially map differences in grain size and texture. We have developed a travelling three-component vector magnetometer that can be run alongside core to map its external magnetic field. The logger has been designed to operate in core sheds and at remote drill sites. It is used to rapidly scan a length of core, with each core being scanned in different rotations. The magnetic field contributions from any remanent magnetisation rotates with the core and cause differences between successive measurements, while the field contributions from any induced magnetisations with isotropic magnetic susceptibility remain constant. Deconvolution of the magnetic field data with simultaneous three-channel inversions of the multirotation data separates remanent and induced components. Interpretation of this data provides estimates of the intensities of induced and remanent magnetisations, the orientation of the remanent magnetisations and the ratios of the induced and remanent magnetisation strengths. We expect these magnetisation parameters to correlate with stratigraphy through a banded-iron formation. Furthermore, we anticipate that we will be able to use this information to map zones of oxidation and other changes along the core. This novel instrument is one component of an integrated CSIRO program to provide new capabilities for iron ore exploration and development based on studies of magnetic fields and magnetisations at scales ranging from centimetres for these core investigations to tens of kilometres for formation studies.CITATION:Foss, C A, Leslie, K and Arnold, C, 2015. Rapid logging of different magnetic phases in banded ironstones using a travelling three-component vector magnetometer, in Proceedings Iron Ore 2015, pp 271–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By G Chitombo

Mass mining methods have become the mining industry’s preferred way of extracting most of the world’s most important metal and mineral commodities. Given the rapidly increasing global demand for commodities, the requirement to increase the contribution of some of these (eg copper and gold) from underground sources also continues to grow. In the case of copper this contribution is needed by a number of major producers to supplement production from their ageing deep open pits. Satisfying this increased demand will require the design, construction and operation of more effective, higher capacity and larger scale mines which, in turn, will require enhanced mass underground mining techniques such as block caving (BC), panel caving (PC) and sublevel caving (SLC).It is now widely accepted that future discoveries of orebodies, which will be developed using these methods, are almost certainly to be much deeper than the deposits presently being mined in this way and made more challenging because of the likelihood that the associated grades may be much lower than currently mined. The design and mining of future large-scale cave mines (supercaves) will become crucial in order to extract full value from such deposits. An essential prerequisite of this will be a much improved knowledge of the deposit, ie Total Deposit Knowledge. In this context, Total Deposit Knowledge is the characterisation of the ore deposit and its surrounds at all scales and includes; rock type (lithology), the spatial orientation of a range of geological features or discontinuities, rock mass fabric knowledge, metal grade and distribution data, geometallurgical data (including alteration), geo-hydrology, permeability and porosity. This is the information that will be used, as now, to delineate geological and geotechnical domains and construct models, but with outcomes superior to those presently available. From this information better-informed feasibility study design decisions and performance predictions must be made. In summary more geological information and analysis is required and this needs to be aligned to potential mining and processing requirements much earlier in the project than commonly occurs.

Aug 22, 2011

By A R. Penney

Safety management, both personal and that associated with catastrophic hazard, helps to define the success of mining companies. Personal safety management, often categorised by slips, trips and falls, has been widely addressed, with numerous approaches successfully adopted. Catastrophic hazard can lead to a single accident (eg ground collapse, underground fires etc) causing multiple fatalities. Catastrophic hazard management in mining is an emerging discipline, and as such there are various pitfalls to demonstrate its effectiveness and success; it is much more than simply meeting regulatory requirements. Various standards, guidelines, and leading practices are available for reporting key performance indicators. While measuring and reporting safety related key performance indicators (KPIs) such as Total Recordable Injury Frequency Rate (TRIFR), Lost Time Injury Frequency Rate (LTIFR), are important, they often lack detail, and give little insight into the effectiveness of catastrophic hazard management strategies and controls. Catastrophic hazards are low likelihood, high consequence events, and as such demand a different management approach. Companies cannot use the suite of personal safety metrics to help demonstrate management of catastrophic hazards. In-field verifications have revealed that senior management commitment to safety is often clear, well organised, and resourced. However, there are often some inconsistencies between what management promotes and plan, to what the operational teams understand and implement. Communication and clear understanding of expectations were the common themes identified to help empower supervisors to reinforce requirements of catastrophic hazard management. A lack of specific, measurable, and time-sensitive goals and objectives for the short- or medium-term, making it challenging to track progress was another key observation. Development of an integrated, multi-disciplinary auditing process executed by an experienced team of technical subject matter experts, provided an in-depth understanding of the requirements of catastrophic hazard management. Areas such as underground fire prevention, explosive storage, electrical safety, mobile vehicle interactions, ground control, inrush, and shafts and winders management have substantial overlap and intertwined processes, and similar strategies for emergency responses. Auditing of catastrophic hazards and safety management systems compliance is only the first step in safety assurance. Completing operational performance audits in technical areas and benchmarking the site verification of safety management documents and verifications forms a critical part to clearly demonstrate industry leading safety practices. No longer is it the external inspection or regular hazard management plan review requirements that dominate, but rather the culture of continual hazard identification, management, controls verification, underpinned by improvement and follow-up verifications of the corrective actions.

Mar 29, 2023

By S B. Sheldon

Wall control programs tend to be expensive and consequently require financial justification in order to get approval for the expenditure required. The difficulty faced in getting this approval is that the outcomes of a wall control program are all subjective – a prediction of wall stability and what the wall would do with and without the program. Determining a net benefit is difficult and often justification of a wall control program is based on gut feel, history and a good selling campaign to build a perceived need.This paper outlines a simple solution to this problem by applying risk management principles to wall control. The process is to identify the risks to the operation associated with current wall conditions and then build a risk database for different potential scenarios for each risk. A financial impact is assigned to each risk scenario to complete the database. A consequence and likelihood analysis of each of the risks is undertaken and a formula applied to estimate the projected cost to the operation for the current risk profile. The process is repeated for the predicted wall control conditions after the application of the wall control program. A successful wall control program will reduce an operation’s risk profile so this projected cost should be less than that calculated for the current scenario. The difference in the two projected costs is the value that the wall control program has produced and this value can be used to determine the net financial benefit potential for the wall control program.This methodology can also be applied to other improvement programs that focus on risk reduction such as vibration control.

Nov 8, 2011

By G Brudek, P Elestedt

Schalker Eisenhütte und Maschinenfabrik GmbH, Nordic Minesteel Technologies and Bombardier Transportation have developed an evaluation tool that considers the main cost drivers of the rail, truck and conveyor haulage systems on the market today. In almost every circumstance, the advantages of a haulage solution are clear. A haulage system is outlined that is fully automated, including driverless operation, and that provides increased tonnage, safety and equipment life and reduced maintenance downtime. The haulage system has been implemented by a number of companies, including Codelco, LKAB and Freeport’s Grasberg mine. CITATION:Brudek, G, Elliott, R P and Elestedt, P, 2016. Moving mORE for less, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 535–542 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By P Kittler

In the spectrum of mining-related disciplines, geometallurgy sits between resource geology and metallurgical engineering. Unlike its neighbours, it is a relatively young discipline and its concepts, procedures and techniques are still evolving. Relevant geometallurgical issues differ from one deposit to the next so there is no single template that can be used in all situations, meaning that geometallurgy programs are nearly always customised and tailored to the deposit and the situation.Over time, a number of key mistakes are seen to emerge regularly. The eventual impact of these mistakes can vary from suboptimal performance of mine and plant to complete failure of the operation. For instance, poor characterisation of ore lithologies and their spatial distribution can have negative impacts on processing plant throughput. However, when combined with failure to identify critical blending constraints it can result in a totally inoperable plant.A number of common mistakes committed during geometallurgical programs are discussed and some preferred alternative approaches are suggested

Sep 5, 2011

In considering the organization of research, it is necessary to know just what research is, what objects are in mind when setting out to conduct research, and what are the functional units which are required to enable a coordinated effort in research to proceed.The dictionary defines research in the following terms: Laborious and patient search, as for truth, diligent inquiry or examination in seeking facts or principles; inquiry, scrutiny; to search or examine with continued care; to seek diligently; to search again; to examine anew.This is, of course, simply a formal definition, but the reference to "labour", "patience" and "diligence" should be noted.The following quotation from an answer to the question "What is Research?", published recently in a technical journal, puts some life into the formal definition:- Essentially, it (Research) is nothing but a state of mind a friendly, welcoming attitude toward change. Going out to look for a change instead of waiting for it to come. Research, for practical men, is an effort to do things better... The research state of mind can apply to anything: personal affairs or any kind of business, big or little. It is the problem-solving mind as contrasted with the let-well-enough-alone mind . . . It is the "to-morrow" mind instead of the "yesterday" mind. Note the statements that: Essentially, it (Research) is nothing but a state of mind, and the research state of mind can apply to anything.

Jan 1, 1950

By A Larsson, K Niiranen

The Palaeoproterozoic Leveäniemi iron oxide apatite (IOA) deposit of the so-called Kiruna type is currently mined by Luossavaara-Kiirunavaara AB (publ.), commonly known as LKAB. The mineralogy of iron oxides, ie magnetite, hematite, maghemite, and goethite is more complicated compared to the neighbouring and more famous IOA deposits of Kiirunavaara and Malmberget. Furthermore, the mineral chemistry of the iron oxides in the Leveäniemi deposit is also slightly different. Especially, the information about the deportment of titanium and vanadium in iron oxides and distribution in the deposit is essential since they can have an impact in the steelmaking process. For this study 50 samples were selected from exploration drill cores and investigated by optical microscopy, FE-SEM-EDS and EPMA at LKAB and the Geological Survey of Finland. Investigations revealed that magnetite is the predominant iron oxide mineral with secondary hematite being the second most abundant mineral. Primary hematite, maghemite, and goethite seem to be less abundant. It should be noted, however, that this investigation focused on magnetite which currently is the only mineral with economic value. Vanadium occurs as a substitution element in the crystal lattice of iron oxide minerals in the Leveäniemi deposit and not as discrete stochiometric vanadium minerals. In the investigated samples vanadium concentration in magnetite ranges from 0.12 to 0.32 wt per cent V2O3 with higher concentration in the southern part of the deposit. Contrary, titanium does not substitute for iron in the crystal lattice of magnetite or secondary hematite (less than 0.018 wt per cent TiO2). It either occurs as tiny inclusions of titanium oxide minerals or as exsolution lamellae of ilmenite in magnetite. The spatial distribution for titanium in the deposit, however, remains unknown. Furthermore, results of this study indicate that alteration of primary magnetite to secondary hematite has had no significant effect on the trace element chemistry of these minerals in the Leveäniemi deposit.

Nov 8, 2021

By F Radke, P A. Tilyard

Determination of the mineralogical location (deportment) of minor and trace elements (including credit and penalty elements) in base metal concentrates can indicate whether further processing is likely to (a) reduce the levels of the penalty elements, and/or (b) direct selected elements into other plant products, thereby increasing current concentrate grade or increasing payment for credit elements. To determine the deportment of elements requires knowledge of the proportions of the minerals present and their individual element contents. In addition, knowledge of the liberation and locking is important, as this can affect any possible further processing. Mineral proportions can be determined by a variety of methods including chemical analysis, point-counting, area-counting, QEM*SEM, image analysis and mineral separation. In the case of a Broken Hill zinc concentrate, several of these methods were used and gave consistent results.

Jan 1, 1998

By R D. Morri, D J. Alexander

The design and optimisation of mineral flotation circuits is currently performed using a combination of laboratory, pilot plant and full scale testing. Owing to the variable nature of flotation circuits and the complex nature of the flotation process, it is difficult to interpret the data collected from flotation testwork. JKSimFloat is a computer modelling package which is being developed to interpret flotation testwork data collected at the various stages of the mining cycle. The parameters derived from the program can be used to assess potential circuit configurations in both the design of new flotation circuits and in the refinement of existing operations. The aim of this paper is to outline the modelling methodology used in JKSimFloat and to outline how it can be used effectively to model data collected from either the laboratory, the pilot plant or the existing flotation circuit. The use of flotation model parameters in circuit evaluation will be demonstrated via the use of a case study based on data collected from ComincoÆs Red Dog lead flotation circuit.

Jan 1, 1998

Effect of Hardwater on Selective Flocculation of Diasporic-Bauxite

Sep 13, 2010

By D Mather, H R. Asche

"In the civil tunnelling field, the use of tunnel boring machines (TBM) has now overtaken the use of conventional excavation methods (drill and blast / roadheader). This is due to a number of reasons, including the increasing availability and reliability of TBMs, the ability to deal with a wider range of face conditions, and the reduced excavation cost that TBMs can bring.Mining companies have spearheaded the advances in shaft boring by mechanised means, both in blind and raise boring. However, mining companies have been slower to adopt mechanised tunnelling.When contrasted with a conventional mining contract, there are good reasons why TBMs in mining applications are relatively rare. A conventional decline contract may have very little geotechnical information. The decline alignment can be subject to change as the tunnelling progresses. The infrastructure requirements are less for a conventional decline, and the sunk cost prior to excavation commencing is lower. Contract documents can be very simple.The history of TBM use in mining is reviewed and lessons are described. From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.We believe that despite the additional requirements for TBM declines, the cost and time advantage to mining companies is very attractive. The challenge is to recognise and to meet the requirements for success in a TBM drive to achieve the advantages of: faster advance rates reduced rock damage/overbreak reduced support requirements uniform muck characteristics greater personnel safety.From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.CITATION:Asche, H R and Mather, D, 2014. Use of ?tunnel boring machines in the mine environment, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 655–662 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014

By M Campbell, A Jeffcoate, J-C Vannay, B Perriaux

Phyllite waste rock at the Simandou Pic de Fon and Oueleba Iron Ore deposits (Guinea, West Africa) variably weather to form clay-rich rocks. This weathering modifies the mineralogical, geochemical and mechanical properties of the phyllites. Final pit walls will largely be formed in phyllite, so it is critical that the slope design takes account of the distribution and variability of weathering within this material. Phyllite intact material strength has been correlated with geochemistry (ie mineralogy) facilitating the establishment of domains of intact rock strength (IRS). In order to calibrate this geochemically-based strength model, core from diamond drilling (DD), comprising a variety of phyllite material types (from soft clay to moderate strength rock), was geotechnically logged to assess intact strength; further validation was achieved by uniaxial compression (UCS) testing and point load tests (PLT). The correlation between geochemistry and strength offers a potentially powerful tool for differentiating basic mechanical properties of the rock mass, especially at Simandou where a significant proportion of the resource drilling is done by reverse circulation (RC). Unlike DD, reliable measurements of material strength from RC samples can prove difficult, especially in clay-rich material. Therefore, gaining information from routine geochemical assay results, independent of the sampleÆs physical integrity, is a valuable and cost-effective source of reliable empirical data. Data acquired using this approach provides an opportunity to develop strength domains, which are integrated into mine planning block models. In combination with other geotechnical characteristics, this can be a valuable input to the development of geotechnical models. This technique has allowed spatially representative rock strength data to be derived and offers the potential for optimising pit slope angles in areas where hitherto conservative design criteria had been assumed.CITATION:Jeffcoate, A, Campbell, M, Vannay, J-C and Perriaux, B, 2013. Modelling intact rock strength of clay-rich rocks with geochemistry at the Simandou iron ore deposit, Guinea, West Africa, in Proceedings Iron Ore 2013 , pp 193-202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By D Matthews

With the increasing demand for quality-specific ores, coupled to the reality of even more complex minable iron ore reserves, there is a growing need for real-time online material analysis of plant feed and product. For a full system mass balance, the combination of conveyor weight scales, flow and density transmitters are required. This alone does not guarantee product grade. For optimal process control and material blending, real-time online elemental scans in combination with the mass weighting is becoming more than a ‘nice to have’. These elemental scans located at key positions, enable the mining and plant operators to make informed decisions timeously, therefore ensuring product outcomes and optimising operations where material grade and the control thereof are important. Typically, these units follow the mining and primary crushing circuit as well as on the product conveyors, low-grade conveyors and tailings lines. Deployed after the primary crushing circuit, an analyser acts twofold:1. guaranteeing mining production, and2. processing facility feed blends.The analysers on the product conveyors guarantee saleable product. The analysers on the low-grade conveyor and tailings line complete the elemental balance and identify the potential of the low-grade and tailings for future processing. The system losses (accumulation) are calculated to determine the amount of material ‘lost’ during the processing stage which does not report to any of the aforementioned and can be used as a measure of the efficiency of the plant. A further advantage of the real-time online analysis of material is that immediate intervention can be taken in the event that the product is not of saleable product grade requirements. In the Khumani Iron Ore mine, Northern Cape, South Africa, run-of-mine (ROM), product and control analysers were included. Run-of-mine and product stockpiles are certifi ed, low-grade material is not currently directly measured, but calculated from the internal control loops. Iron units are reconciled between product and feed material.

Jul 11, 2011

By R Crosbie, K C. Runge, E Tabosa, J K. McMaster

Flotation feed density is an operating parameter which is currently not well understood. Most models of flotation only incorporate its effect on particle residence time, but it is likely to have additional effects within both the pulp and froth phases of the machine. Test work was performed in MetsoÆs 3 m3 RCS test rig to investigate the effect of flotation feed density on metallurgical performance. The rig was operated at Rio TintoÆs Northparkes operation using flotation feed and scavenger tail. For each feed, tests were performed at different feed densities, and measurements were performed to estimate the pulp and froth recovery as well as other key flotation parameters (eg bubble size, turbulence and froth stability). Results of this test work have shown that the pulp density does affect key parameters of the flotation process in both the pulp and froth phases. Pulp phase kinetic rates decrease at high density and this is attributed to a reduction in the turbulence within the cell. Froth phase recovery, however, improves presumably because of a stabilising effect due to a greater loading of solids on bubble surfaces.There is a need for more research to be done to better understand these interactions so that metallurgists can determine the optimum flotation feed density to use at a particular operation, or within a section of a flotation circuit.CITATION:Runge, K C, Tabosa, E, Crosbie, R and McMaster, J K, 2012. Effect of flotation feed density on the operation of a flotation cell, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 171-178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By K McSweeney, A Marton

This paper discusses the development of a strategy for ensuring long-term geotechnical stability of final pit walls at AngloGold AustraliaÆs Sunrise Dam Gold Mine. The strategy makes use of improved blasting techniques, changes to the mining sequence and other geotechnical techniques. Only the blasting techniques will be discussed in this paper. These were developed from numerous trials over a period of several months from May 2003 through to November 2003. The focus was to reduce crest loss damage and thereby improve final wall integrity, maintain designed safe berm widths, and ensure long-term stability. Crest loss mechanisms are now understood and are explained in this paper. The preferred solution is outlined; which is a combination of improved blasting and changes in the mining sequence to cater for pre-existing ground conditions. These ground conditions include dynamic hyper saline water with sometimes intersecting steeply dipping discrete structures. Project requirements were defined as mitigating or eliminating crest loss using 127 mm diameter pre-splitting and targeting minimal production blasting vibration levels against the walls. Blast results were measured by post blast visual inspections and video. Blast design input utilised the predictive algorithms built into simulation software when attempting to minimise vibration levels against the walls. Protection of the already fired pre-split line is now achieved using small charges against the wall and timing sequences which form a mask for the later firing main charges. The pre-split spacing is now modified to suit the geology. There eight blast domains identified around the perimeter of the pit, each having varying joint orientation. In addition, blasting the bench adjacent to the berm crest has particular considerations not required by the middle and lower benches. The preferred solution was to purposefully translate this damaged top section of the pre-split bench into a planned subsequent dig zone. The design of this top æweightÆ is a direct response to the nature of the crest loss mechanism.

Jan 1, 2004

By B W. Atkinson

Full-stream mechanised sampling apparatus, that collect a full cross-sectional increment from the complete screen discharge, will always be the preferred option for sampling screen overflows. However, the reality is that provisions for automated sampling are rarely, if ever, provided at the discharges of individual screens within beneficiation plants.Sampling from the discharge of high capacity vibrating screens, especially multi-slope screens, is subject to sampling bias, due to the stratification of the ore that occurs on the vibrating screen deck. The stratification in the vibrating bed translates to a stratified falling stream at the discharge end of the screen, typically with smaller particles at the back of the falling stream and large particles at the front of the falling stream (Figure 1).The chemical and physical characteristics of heterogeneous ore (mineral or coal) particles vary significantly with particle size. If samples do not correctly reflect the source material size distribution, they will be biased and the resulting analytical/assay data will not reflect the actual physical nor chemical characteristics of the source material.Prior published data for coal preparation research (Australian Coal Association Research Program) has demonstrated that a bias appears to exist for samples collected from high capacity multi-slope screens.A new form of sampling scoop has been developed with the aim of overcoming this issue.Bias was evaluated at a coal preparation plant by comparing the desliming screen overflow size distribution to that for æreferenceÆ coal preparation plant feed samples collected using the recognised stopped-belt technique. The study procured 20 sets of comparison samples in order to ensure statistical relevance.Two forms of sampling device were employed for the multislope screen discharge.A conventional square aperture scoop was demonstrated to exhibit a significant coarse bias, in that the resulting samples exhibited a significantly coarser size distribution compared to the reference samples. In other words it was evident that the conventional scoop æfavouredÆ material from the front of the falling stream.A new æcollapsibleÆ sample scoop was evaluated in parallel, and its samples were found to exhibit no relevant bias.CITATION:Atkinson, B W and Swanson, A R, 2012. A new method for sampling from high capacity screens, in Proceedings Sampling 2012 , pp 89-94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By H Hy÷tyniemi

In this paper multivariate data analysis performed on a new multi-camera system implemented to zinc flotation circuit of PyhSsalmi mine is presented. Image-analysis-based system was developed to take advantage of the commonly known fact that the changes in the flotation process are reflected to the visual appearance of the froth surface. Most often the changes are seen first in the froth and later in other process measurements. The image variables are already utilised in closed loop control and considerable savings are achieved with the current setting, but the results coming from the separate cells are used individually. This is clearly not the optimal way to take advantage of the many measurements coming from different locations of the process. A better approach would be for example to use the measurements coming from the early stages of the process to predict the behaviour (or improve the quality of measurements) in the later stages. The methods described in this paper are aimed to improving the situation in this sense.

Jan 1, 2005

By P Wahyono, H Vega, S Riza, P Vergara, P Gonzalez-Carbonell

PT Freeport Indonesia (PTFI), operating in the Ertsberg Mining District in the Province of Papua, is developing the Grasberg Block Cave copper-gold mine. The site aims to output 160 000 t/d and will be located underneath the current Grasberg Open Pit. Initial studies of the potential to develop a block cave mine in the Grasberg orebody have revealed that the mine will require significant volumes of air. The Grasberg Block Cave (GBC) project requires four primary fans (3750 kW each) to support production at full capacity.Fan #1 commissioning was accomplished successfully on 9 February 2012. However, Fan #2 chamber, which is separated by a 20 m pillar, had not been completed. The main challenge was Fan #2 chamber still needed to be benched. The risk of damage to the critical infrastructure in Fan #1 chamber, including ground support, cracks in pedestals, and misalignment in the impeller shaft were considered. The challenges were blasting the bench without damaging the surrounding infrastructure, completing the work safely and meeting the schedule. This was achieved with the engineering control methodology. This paper summarises the benching process of Fan #2 chamber and its impact upon Fan #1.CITATION:Vega, H, Riza, S, Gonzalez-Carbonell, P, Wahyono, P and Vergara, P, 2013. Excavating an underground primary fan chamber that is adjacent to a fully operational primary fan in PT Freeport Indonesia's Grasberg Block Cave Mine, in Proceedings The Australian Mine Ventilation Conference , pp 115-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By S Farrokhpay, C Akop

Copper-gold-pyrite ore types with an elevated pyrite head grade utilise a sequential flotation circuit to recover initially a copper-gold concentrate with a pyrite-gold concentrate being produced from the tailing of the initial circuit.A simpler flotation circuit with lower operating and capital costs for treatment of such copper-gold-pyrite ores with an elevated pyrite head assay was sought in the described work. After characterising the ore, the objective was to apply bulk rougher flotation of both the copper minerals and pyrite for the copper-gold-pyrite ore at natural pH. Hence, no lime or other pyrite depressants were required in bulk roughing. The bulk rougher concentrate was upgraded in a cleaner circuit to reject non-sulfide gangue and then the resulting sulfide concentrate was separated by depressing the pyrite to produce two products (copper and pyrite concentrates, both having significant gold assays). A standard test with a sequential circuit was applied to the same ore for comparison.The chalcopyrite and pyrite losses in the tailing from the rougher circuit were the same for both bulk and sequential roughing (less than six per cent). In cleaning (bulk circuit), the effective pH for pyrite depression was 11.8–11.9; copper recovery was 70–75 per cent (grade of 15–20 per cent copper) and the sulfur recovery (pyrite product) was 80–85 per cent (grade of 34–36 per cent sulfur).These results approached those for the sequential circuit where copper recovery was 80–85 per cent (grade of 15–20 per cent copper) and the sulfur recovery (pyrite product) was 83 per cent (grade of 38 per cent sulfur).The observed effects of feed sizing on the liberation of minerals in the rougher feed are discussed. Options for improving the bulk circuit results are also considered. Importantly, the implications of various aspects of these findings for the bulk circuit are discussed with an industrial focus.CITATION:Akop, C, Farrokhpay, S and Johnson, N W, 2014. An alternative circuit for chalcopyrite-pyrite ores with elevated pyrite content in Cu-Au ore treatment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 407–416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014