Search Documents

The major heavy industrial consumers of limestone are the cement, lime'and steel ind- ustries. Each of these requires large quantities of cheap raw material. Other ind- ustries such as glass and chemical manufactur- ing are significant consumers and agricultur- al and constructional activities provide additional demand which is usually more local in its occurrence. Limestone is widely dis- tributed throughout Australia but location in relation to major markets, and transport con- siderations render most deposits of no economic value. Among deposits which are sufficiently close to the major metropolitan markets many must be rejected as being unsuitable on grounds of quality, inadequate size for major.develop- ment, or other reasons such as environmental considerations. The major producing locations are sit- uated in a variety of geological environments. Most have limited reserves and require partic- ular attention to quality control. Planned extraction programmes based on detailed geo- logical investigations enable not only satis- factory grade control but also permit, by the adoption of appropriate quarry procedures, the use of sub-grade material, thus optimis- ing utilisation of the available reserves.

Jan 1, 1976

Agglomeration Drum Selection and Design A model has been developed by for drum agglomeration which allows selection of geometry and power input. Specific aspects considered are: calculation of total operating volume, solids residence time based on drum geometry and operating parameters, selection of the drum aspect ratio, selection of proportion of critical speed, calculation of rotating power requirements. The model uses solids total residence time to calculate the required operating volume. The burden density is calculated from the solids bulk density, agglomerate packing and the fluid density. Power is calculated using a modified Liddell and Moys correlation for burden position and shape, and the operating drum speed. A further power allowance is made to allow for accretion drop off during drum rotation. Results from the model (especially power and per cent operating fill) have been verified from industrial installations of significant size. Predicted and observed power draws are within five per cent when burden slip and bypassing are not significant. When these are significant (at fills above 15 per cent) the actual power draw will be less than the model prediction. Under these circumstances the quality of the agglomerates will be poor.

Sep 13, 2010

The efficient development and exploitation of an orebody relies on an understanding of the mineral characteristics of the deposit. This information is valuable throughout the mining cycle - during exploration, assessment, testing, design, operation and rehabilitation. Problems can arise at each stage if there is an inadequate appreciation of the mineralogy involved and its effects on the treatment process. Modern image analysis systems now permit a more quantitative understanding of the mineralogy of an ore to be gathered. Where previously the metallurgist had to rely on qualitative information to guide technical decisions, it is now possible to give numerical estimates to the compositional and textural properties which govern the mineral concentration processes. Ore samples can be characterised according to modal abundances, mineral grain size parameters and mineral associations, all of which affect the liberation and concentration of the values. The paper will discuss the application of quantitative process mineralogy by considering a number of case studies. These include: ore characterisation to assist in exploration, assessment and mine planning; modal analysis of complex mineral suites to assist in the evaluation of ores, the deportment of values between products and the recovery or loss of these values; liberation analysis for ore testing, plant optimisation and performance monitoring; and characterisation of tailing to guide estimates of leachability, stability and rehabilitation options.

Jan 1, 1998

By R Gilbertson, N Freeman

Metallurgical accounting is key to the control and production planning process of any mining operation. This is even more crucial for complex operations involving mining, concentration, smelting, refining and marketing. The tracking of multiple metal product and contaminant components through the operation can improve process predictability and inventory management. Appropriate use can be made of æhigh quality dataÆ for strategic reserve utilisation, mining operations, milling operations, etc. This information enables the optimisation of all aspects of the mining and processing operations. This case study discusses a metal balance implementation for WMCÆs Olympic Dam operations; a large integrated mining, concentration and refining operation, which used an existing off the shelf statistical data reconciliation package developed for the oil industry. It was extended to track and balance the metal co-products across the entire integrated mining, mineral processing and refining plant. The key benefits discussed are tight integration with existing data collection systems, formalisation of previously informal processes, and leveraging the development and support available for a widely used package. The project provided a solution for the site metallurgical balance spanning the mine and processing plant. The solution facilitates a bridge between the planning and production worlds, using a common data model across the site.

Jan 1, 2002

In the mining and minerals industry, development, introduction and construction of new plant designs, to meet sustainability objectives, face a series of major hurdles. Typical are the long investment cycle times, the designer does not normally control the spending (the owner does), and the industry is inherently technologically conservative or risk adverse while accepting the often more significant geological, market and political risks.æSustainable Plant DesignÆ is an approach to plant and facility design that drives the necessary culture change and acceptance by minimising technical risk and maximising potential returns. The approach forces consideration of sustainability objectives and risks early in the project, where cost saving and efficiency improving opportunities can be maximised.In Hatch, we are using three proven tools under the ærisk managementÆ umbrella to drive sustainable development principles into our projects:Sustainable Plant Design, FutureWatchTM Reviews, and Clean Plant DesignTM . These proactive practical, not theoretical, techniques for driving change from within and reducing whole of life cycle costs will be discussed and illustrated with case studies.

Jan 1, 2004

By Davies S. G, Jayaweera A

The oxidation of nickel sulphide and copper sulphide concentrates, and coal, has been studied under non-ignition and ignition conditions using Differential Thermal Analysis (DTA) and Thermogravimetry (TG). The non-ignition reaction was favoured by slow heating rates < 10°C min-1), low masses < 10 mg) and an air atmosphere. Under these conditions, the typical stepwise oxidations of the various sulphide minerals present in the concentrate were observed as resolved exothermic peaks in the DTA curves and weight losses in the TG curves. Above a heating rate of 10°C min-1 , sample masses in excess of 10 mg and an oxygen atmosphere, an ignition reaction was induced, as indicated by a major high energy exotherm in the DTA curve and a major rapid weight loss in the TG curve. The ignition temperatures of the minerals under ignition conditions, found for 15 mg samples heated at 20°C min-1, were 434°C for the nickel sulphide concentrate, 372°C for the copper sulphide concentrate, and 230°C for the coal. By plotting a curve for mass against ignition temperature at constant heating rate and extrapolationto zero mass, a value of 470°C was obtained for the mass independent ignition temperature of the nickel sulphide concentrate. Ignition temperatures and extents of reaction at various temperatures were obtained using the TG technique in a novel manner which produced heating rates of 4500°C min-1. Under ignition conditions, the oxidations approximate to flash smelting conditions.

Jan 1, 1985

Accidents in open pit mining have a high cost in lost time of person- nel, damage to equipment and installations, and lost production. The realities of export competition require that Mine Management sig- nificantly reduce the costs associated with accidents and workplace ill-health. Newer management approaches are proving effective in reducing the Total Cost of Risk through a strucured Occupational Health and Safety Programme exhibiting the following features: ò Formal Company Policy ò Accountability for OH&S performance clearly designated to each level of management and supervision ò Effective utilisation of a Mine Occupational Health and Safety Co- Ordinator and a Mine Occupational Health and Safety Adviser ò Development of realistic OH&S Objectives ò Training of Management, Supervision and Workforce in Occupa- tional Health and Safety ò Development and adoption of Safe Work Practices and Procedures ò Effective employee selection procedures, control of Contractors ò Monitoring of the health of the workforce ò Collection, recording and distributing information on all Mine inci- dents, accidents, injuries and damage ò Ensuring that the Mine environment is healthy and safe ò Effective Emergency Procedures to deal with injury, fire, rescue and other situations of risk ò Controlling those Mine hazards which cannot be removed ò Adopting a high standard of Occupational Rehabilitation ò On-going visible Management participation in the programme to ensure that momentum is developed and maintained. This approach requires that Occupational Health and Safety be given equal status with product quality, maintenance of plant and output per- formance; its implementation is rewarded with improved morale and major cost reductions.

Jan 1, 1989

In-pit crushing systems have been known in the mining industry for many decades. The question whether in-pit crushing is a viable option has often been asked. More than 200 mobile and semi mobile crushing systems have been installed worldwide at various locations and applications. Economic pressures have forced mine operators to reconsider the use of a conventional truck-shovel operation and have contributed enormously to the development of in-pit crushing and conveying systems. The in-pit crushing concepts have varying mobility capabilities. These range from fixed, stationary crushing plants to semi-mobile and fully mobile crushing plants. All these systems are operated in connection with a conveying system. In general in-pit crushing systems have technical and economical cost advantages over truck-shovel operation, particularly as mine capacities increase and mines become deeper. The integration of an in-pit crushing system represents a significant up-front capital investment and the mine is only able to depreciate the capital investment over a sufficient mine life including plant capacity to realise the benefit of the much lower operating cost.

Jan 1, 2003

It is indeed an honour to address the perth branch of the australian institute of mining and metallurgy and to have the opportunity to talk to you about the future role of upgraded ilmenite on t102 feedstock supply and demand. There have been many papers written on upgraded ilmenite supply and demand and now I would like to share with you QIT's view of the situation first, a word about demand, although I will be talking principally on the supply issue. The principal use of t102 is in the manufacture of pigments which, in turn, are used in paints, plastics, and the paper industry together with a few miscellaneous uses, while a further b% or so of t102 minerals are consumed for the manufacture of titanium metal and for the manufacture of welding electrodes. the total demand for contained t102 is of the order-of 3 million tons per annum, and the general consensus in the industry is that growth rates should be of the order of 2% annually- it is against this backdrop that suppliers must compete with one another and produce least cost materials for the pigment industry. At the moment, supplies are relatively tight, but the generally slow growth in demand coupled with the abundance of titanium bearing minerals should ensure that long term the reverse is generally true. Now, let us examine the supply situation. Titanium is the 9th most abundant element in the earth's crust, so the problem from the producers` point of view is not one of scarcity of titanium minerals, but of how to extract most economically t102 feedstocks from a wide variety of choices- up to the present, all titanium feedstocks are being derived from either rutile or ilmenite rutile, at about 95% t102 content, is indeed a premier raw material which does suffer from potential scarcity and rutile supplies will likely be a diminishing factor in future decades- whereas ilmenite, a combination of iron and titanium oxides found in varying ratios, may be found in huge quantities all over the world.

Jan 1, 1986

This is the second of a series of papers dealing with Geology in Exploration. The first, published by the Australasian Institute of Mining and Metallurgy, Proceedings Nos. 143-144, 1946, was written as an introduction to the subject and employed the exploration geology of the Cobar field to illustrate the prospect thinking. This paper will be concerned with the problem of ore repetition in depth and borrow its- example from the Mount Lyell copper field. The writing will be taken up altogether by the example. Nevertheless the intention remains to develop the subject in terms of its wide interest and application.The Mount Lyell field possesses large actual and prospective resources within, and in the vicinity of, the known deposits. This paper does not bear at all on these accessible ore reserves and tangible prospects. There is also in this area evidence of deep ore. The possibility is of little practical interest at present. But the picture of ore repetition, exemplified by the Mount Lyell field, does matter now to the outlook on exploration in this country. For once this essential feature of ore occurrence is widely understood there may develop, on the scale warranted, the search for major deposits which do not outcrop but which are still at shallow depths because of the part erosion plays in this story of concealment and exposure of ore. Also there is the chance in some fields (including Mount Lyell) of a second harvest of orebodies within mineable depths. This exploration goal, introduced in the first paper, will appear more clearly as the Geology in Exploration series is written up. Here the concern is to show the character of the geological evidence which points to the occurrence and recurrence of ore in the earth's crust, the picture at the foundation of this exploration scheme. There is considerable information in the Mount Lyell area of the structures...

Jan 1, 1947

By L Reynolds

The portable infrared mineral analyser (PIMA) was trialled to determine the extent and intensity of any hydrothermal alteration halo associated with gold mineralisation in the Hyde-Macraes Shear Zone (HMSZ) of the Otago Schist.   Twelve diamond drillholes through the HMSZ were analysed with the PIMA at a sample spacing of 1 m. The drillholes were selected on two traverses along the line of strike and down-dip of the mineralisation in and around Panel 2 of the Frasers underground development.   The study showed that the Hangingwall shear of the HMSZ has a more distinctive infrared signature in intersections with high grades. The Hangingwall shear in these drill holes is defined by a shift in the wavelength of the Al-OH absorption feature from ~2220 nm to <2210 nm. This shift is attributed to a change in the mineralogy from phengite to muscovite. Overprinting this trend in some of the drillholes is the presence of the 2210 nm Al-OH absorption feature, ascribed to kaolinite. Kaolinite also tends to be present in numerous other regions of the schist above the Hangingwall shear associated with steeply dipping faults and foliation parallel joints. In drill holes with low grades the Hangingwall shear does not exhibit any obvious infrared signature.   At the scale of study, the PIMA does not provide evidence for an alteration halo associated with hydrothermal mineralisation above the Hangingwall shear. Possible tectonic movement may have displaced any alteration halo that once existed, away from the zone of mineralisation. For this reason, PIMA apparently cannot be used for predicting the location of the Hangingwall shear during exploration drilling. However, the study did show that the PIMA could define the Hangingwall shear when the rocks were sufficiently altered and mineralised.

Jan 1, 2007

By E Werner, J J. Donovan, A J. Morris

Coal mining in the Pittsburgh coal seam, in the eastern United States, began in the late-1700s. Since that time numerous mining technologies have been used throughout the basin. Environmental concerns, particularly mine discharge quality, have only been considered since the early-1970s. During the last 20 years, many of the larger underground mines have closed and are now either flooding or already flooded. In order to understand the consequences and potential future effects of this flooding, mine mapping of the basin has been compiled utilising a geographic information system (GIS) with an emphasis on locating barrier pillars between mines. Mine flooding has been monitored at numerous sites utilising pressure transducers and data loggers. These data have been combined with historical data from mining companies and structure contour maps to yield chronological flooding maps of the basin from 1980 to present. Utilising these maps and the indicated flooding rates, future discharge locations have been identified along with estimates of when these discharges are likely to occur. Related work has identified barrier pillar hydraulic conductivities and vertical infiltration rates as a function of overburden thickness. All of this information has been integrated into a groundwater flow model that simulates mine flooding. This model is useful in defining mine to mine interactions as the various mines fill with water, and the testing of various flooding scenarios. The model will be used in evaluating mine discharge rates and evaluating the options for regional mine drainage treatment.

Jan 1, 2003

By E Taylor, F Lebbing

The $2.5 billion EastLink project is a 39 km tollway and includes twin three-lane, 1.5 km long, undrained driven tunnels with cross passages every 120 m. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and help preserve the unique flora and fauna in the area. The design of the permanent concrete lining and waterproofing system for the EastLink tunnels was both innovative and practical, to meet the demanding environmental and production constraints of AustraliaÆs largest road project. This paper describes several key aspects of the tunnel design and construction, including: design of fully tanked, permanent concrete tunnel linings for the main tunnels and cross passages to withstand 37 m head of water pressure in combination with potential rock loading in the future;optimisation of the tunnel shape to minimise the amount of reinforcement required and the design of special welded mesh which was developed within manufacturing constraints;100 year design life and durability considerations in every aspect and detail of the design including concrete mix design and stray current mitigation;development of a precast invert solution for the main tunnel permanent concrete lining to enable faster lining construction and to minimise risks to the tunnel membrane associated with fixing reinforcement and construction traffic;development of prefabricated reinforcement details for the junctions between the main tunnels and the cross passages to enable faster construction and minimise risks to the membrane associated with fixing reinforcement; andincorporating the tunnel drainage sump at the lowest cross passage in the alignment, resulting in deep excavation to satisfy the required storage volumes for drainage.

Jan 1, 2008

In submitting the accompanying sketch and description, the writer mentions that he has found this "gadget" a useful assay office adjunct.He believes that some millmen and assayers have been confronted, from time to time, with large samples of mill pulp for assay purposes and that although the commonly used method of coning and quartering dry sample is simple and effective, provided the samples are of reasonable proportion, the operator is frequently confronted with samples of pulp, sometimes up to 50 gallons. The writer stresses the advantage of being able to handle these samples. This fact inspired the design of the "gadget,"which was developed at the Kalgoorlie State Battery and has been found to give very reliable results. It has considerably eased the work of the assay office.Description. - A cone of suitable dimensions according to requirements (this one is about six gallons' capacity) is mounted on a light angle-iron frame and has a small hand-operated agitator paddle let into it far mixing purposes. The agitator and head frame are removable to facilitate cleaning. Four outlet pipes at the bottom at right angles to each other are controlled with one common plug, externally operated for discharging the pulp.Each operation of the machine delivers four equal parts; one or more of these can be used for further division as conditions require. Samples can thus be reduced to suitable assay room size in a few minutes.The dotted lines, enclosing the shaded portion, represent the four-bladed paddle.Each paddle is slotted with three parallel slots. Unshaded portions represent slots.

Jan 1, 1939

Ventilation challenges are often encountered when an underground mine expands to new zones and it often is the case to make a thorough review of the existing system and assess immediate and future airflow needs at the desired quantity and quality. An unexpected mine plan change that calls for increased development and production from new areas can impose a strain on the existing ventilation system. Budgetary constraints can also demand creativity in design on the mine ventilation engineerÆs part. Since the addition of several mining horizons it had become obvious at the Meikle mine that something had to be done to increase airflow quantity and quality in the old main zones because most of the ventilation resources had been channelled for development in the new mining horizons. An airflow assessment of the existing system had to be performed and it was determined that the airflow quantity had to be increased by at least 30 per cent and the quality of the air had to be improved by reducing nuisance and respirable dust and at the same time reducing the airflow temperature before it was used in a few mining zones. At the conclusion of the airflow assessment it was determined that a third centrifugal fan would be installed on a new 3.05 m diameter borehole from surface to underground. By a careful study of temperature conditions over time it was determined that an evaporative cooling spray chamber would be sufficient to cool the airflow down from the high dry bulb temperatures observed down to saturation at the wet bulb temperature. At the same time excessive nuisance dust generated as a result of the airflow travelling a long way in a haulage drift will be knocked down in the spray chamber resulting in cool, clean air in the mining districts. Expansion of the existing surface ammonia refrigeration plant was out of the question for several reasons. The fact that the airflow was hot and dry meant that evaporative cooling spray chambers could achieve lower working temperatures at a very low cost compared to the expansion of the chilled water plant. The expansion of the ventilation system at Meikle mine and the use of evaporative cooling spray chambers were demonstrated to be very successful and the information presented in this paper can be of benefit to other mines experiencing the same ventilation problems as was the case at the Meikle mine.

Jan 1, 2005

By Y L. Ma, Y Yang, M Chen, W Bruckard

To improve the understanding of the reactions and mechanisms occurring during the leaching of sulfide ores at high temperatures a range of advanced characterisation and sensing tools have been combined to provide a sophisticated and powerful methodology to examine sulfide leaching systems. These include advanced electrochemical methods, surface chemistry and materials characterisation techniques such as synchrotron X-Ray Absorption Spectroscopy (XAS), X-Ray Photoelectron Spectroscopy (XPS), Scanning Electrochemical Microscopy (SECM), and in situ X-ray diffraction (XRD), together with new robust solid state chemical sensors for in situ real time monitoring of key aqueous chemical parameters. The methodology was employed to investigate various sulfide mineral leaching processes. For example, oxidation of arsenopyrite at elevated temperature involves complicated multiple reactions and the process is strongly influenced by the solution conditions, component speciation and mineralogy. The methodology was used to study this system both ex situ and in situ to gain a detailed understanding of the complex chemical reaction mechanisms operating. These mechanisms are discussed in terms of the observed leaching efficiency. The application of this methodology enables complex sulfide leaching systems to be understood more fully such that process efficiency can be improved.

Aug 24, 2022

By E Jak, J Chen, B Hogg, S Nikolic, S Nicol

The quantity of post-consumer ‘waste’ materials generated each year is rapidly increasing. These materials can contain significant quantities of critical metals and present an environmental challenge if landfilled. The ISACYCLE™ technology is a proven solution for the processing of these materials. In the ISACYCLE™ furnace, the post-consumer materials are processed to recover energy along with any contained critical metals, in the form of a base metal alloy or matte. In addition, a clean aggregate (slag) is generated, which has the potential to be used for a range of applications in the construction industry. This slag is commonly based on a fayalite slag but is modified to manage the complex feed. This paper will review the fayalite slag system and the theoretical modifications required for treating urban wastes. Slags from an ISACYCLE™ furnace processing urban wastes have been sampled and characterised. The chemistry of these samples will be reviewed and compared to the expected theoretical modifications required.

Jun 19, 2024

By Davies H, Pigram C, Sunata W, Falvey D, Loxton C, Giddings J, Rogerson R

PALAEOMAGNETIC CONSTRAINTS ON TERRANE TECTONICS IN NEW GUINEA Chris Klootwijkl), John Giddingsl), Wahyu Sunata2), Chris Pigraml), Charles Loxton3), Hugh Daviesl), Rick Rogerson3) and David Falveyl) 1) Bureau of Mineral Resources, Canberra, Australia 2) Geological Research and Development Centre, Bandung, Indonesia 3) Geological Survey of Papua New Guinea, Port Moresby, Papua New Guinea

Jan 1, 1987

By T Perera, B Fan, S Thang, T Hsia

Minerals are valuable resources and critical elements for a broad range of biological and technological applications, including technological developments to improve energy efficiency and the global movement to promote a low-carbon economy. However, in order to extract these critical metals, large amounts of waste and toxic chemicals are generated, as well as the use of high energy and large amounts of water consumption. Froth flotation is one of the most commonly used processes to separate and collect high-value minerals, but it still has some limitations, including low flotation efficiency performances using existing collectors and other reagents. Therefore, there is an urgent need to design and develop new metal-specific collectors to more efficiently separate and recover valuable minerals and to allow bulk water recovery from flocculated tailings. In this research, we propose to use our newly designed and synthesised novel collectors derived from a type of vitamin E (α-tocopherol), a relatively inexpensive and non-toxic natural molecule. As a potential collector-building block, α-tocopherol has a long hydrophobic carbon chain that facilitates the attachment to air bubbles during the froth flotation process. In addition, the phenol group of this molecule can be easily modified to incorporate various functional groups for targeting different types of minerals. Furthermore, α-tocopherol can be converted into a monomer for polymerisation by the reversible addition-fragmentation chain-transfer (RAFT) process, which can provide us with polymer based-collectors with high precision control of molecular weight and architecture. So far, small-scale qualitative experiments on α-tocopherol-based collectors have been performed with good results, which indicates the feasibility of these compounds as novel collectors for improved froth flotation processes.

Aug 24, 2022

By Wyborn L, Giddings J. W, Plumb K. A

The McArthur, Balma (new name) and Habgood Groups are thick (up to 4.5 km) correlative sequences of shallow water evaporitic carbonates, mudstones and sandstones that are exposed largely within the Batten, and southern and northern Walker Fault Zones (Batten and Walker Troughs) of the McArthur Basin respectively. Recent re-mapping of the Walker Fault Zone has provided data for refined stratigraphic correlations between these groups. Two significant hiatuses are now recognised within the Balma Group (base of Vaughton Siltstone and base of Yarrawirrie Formation) and these may represent tectonically-generated sequence boundaries which may correlate with similar local hiatuses within the McArthur Group such as at the base of the Teena Dolomite and Lynott Formation respectively.

Jan 1, 1994