Search Documents

This paper describes the characteristics of blasting which set it apart from other methods of breaking rock. The mechanism of rock breakage and the influence of rock proper- ties are then discussed. The strain and fragmentation produced by a cylindrical charge does not change once the charge is longer than 16 blasthole diameters. The influence of bench geometry, charge length and drill diameter are then examined. It is shown that spherical charges have advantages over long slender cylindrical charges. By selection of the appropriate drill diameter, explosive and charge configuration the optimum blasting practice for a given rock to give suitable fragmentation and muckpile profile for sub- sequent handling can be found. The fragmentat- ion depends not only on rock and explosive properties but also on the pattern which dictates how effectively the cracking is utilised. The size distribution of the fragments is given by the Rosin - Rammler equation. Undesirable cracking of the rock in the final wall can be controlled by the careful design of blasts as they approach the final wall. Finally, it is concluded that because of the distance to which blasting can fracture and then displace rock it is suited for the breakage of large volumes of rock.

Jan 1, 1978

Access to land for exploration, development and mining purposes is extremely critical to the viability of the mining industry and subsequently the well being of society.The mining industry has been subject to environmental controls and considerations for the past 20 years. Today there is greater land use competition and more debate as to its use. To retain reasonable access the mining industry must comply with the rules and regulations by which it is governed.A new set of rules and regulations have been approved for use in Queensland, known as the Mineral Resources Act 1989. This Act clearly outlines the titles available and the requirements to obtain access.There are three main titles of interest to mining companies. These are an Exploration Permit, Mineral Development Licence and a Mining Lease.The Exploration Permit (EP) is for exploration purposes. Applications for EP's are assessed on their content and past performances. An EP is granted subject to a security deposit and conditions. Prior to entry the EP holder is required to inform the land owner of the proposed activities and times of entry.

Jan 1, 1990

By Wang Xia, Zhou Aiming, Shi Shengyi

Zhangmatun Iron Mine is situated in the suburbs of Jinan city, Shandong, China. Because of surface environmental constraints, no suitable site can be selected to dispose of mill waste. The full mill tailings must be disposed of underground. This paper deals with the work conducted at Zhangmatun mine to develop a total tailings backfill system, taking advantage of a doubleshaft blade mixer and an activating agitator to prepare backfill. Cement and ground slag are added to tailings for strength development. Two stopes have been filled and the pillars have been effectively mined out during the field trial. The application of innovative total tailings backfill technology is a new concept at the mine. Detailed planning has achieved a close integration of mining, milling and backfilling. Full mill tailings, with or without rock, are disposed of underground in a continuous process to fill, totally and systematically, the cavities formed by mining. Utilisation of cemented tailings backfill solves not only the problem of disposal of mill waste, but also the resource problem of providing backfill materials to the mine. The strategy also maximises ore recovery for the mine.

Jan 1, 1998

The drilling and evaluation of bore cores provides the best available statistical basis for characterizing a coal prospect. Important, long-term decisions by management frequently must be based on the results. The majority of coal mined presently is used for steam raising or the production of metallurgical coke. Common bore core tests and analyses appropriate to this usage can be cate- gorized as non-destructive, chemical, physical, petrographic, caking/plastometric and propert- ies of non-coal material. The major tests within each category are described. Certain specific information from the bore cores is required by the coal geologist, mining engineer, coal preparation engineer and the user, either individually or as a group. The optimal bore core evaluation test pro- gramme is the one which satisfies the needs of all the professional disciplines with the grtatest speed and at minimal cost. The principal steps in such a programme are listed. There is an urgent need for a bold new Australian standard to provide the necessary guidelines to an industry which at present lacks uniformity in its approach to the task.

Jan 1, 1977

Both innovation and excellence are desirable attributes of education, as they are also markers in the progression of the human race, but how attainable are they? The interaction of minerals and humanity provides a special insight into the development of both criteria, from the discovery that chert cuts, through the Bronze Age and the first use of metal alloys for implements, to using coal, oil and uranium as sources of fuel. However, there have been many hiccups along the way, where excellence in one respect has meant disaster in another. Examples are in the exploitation of asbestos, and in traditionally poor work practices in mining, both contributing to the widespread public belief that minerals and mining are ecologically undesirable. Yet is this perception based on the unrealistic expectation of innovation and excellence being simultaneous qualities of any given process? Common sense born of experience indicates that the journey from one, to the other, is usually a long and often tedious process, with much trial and error before excellence is attained. In our time, the partnership between academia and industry is the usual pathway to achieve it. Even so, we should take care that innovation does not become overwhelmed by the pursuit of excellence: as history clearly demonstrates, humanity depends upon both.

Jan 1, 2004

Computers are playing an increasing role in the management of technical data in mines. Companies are re-assessing the role of their data processing departments as users demand computer resources in non-accounting areas. Data of all kinds is now being seen as a, company resource, and the role of computing professionals is to help to manage the data flow, not merely to manage computers. The concept of distributed data bases puts the responsibility for data entry, editing and updating with the user. This challenges conservative views of centralized control of computing, suggesting, instead, centralized co-ordination. A survey of the possible applications of computers in technical areas points up the special requirements of handling raw, processed and consolidated technical data. Technical data bases have become flexible as mini- computer hardware and software have rapidly developed. Management has the ultimate responsibility for efficiently administering corporate data bases, and it must ensure suitable policies are developed for this purpose, with enough flexibility to cope with the impact of fast changing technology.

Jan 1, 1980

New Zealand's Land and Income Tax Act 1954 contains unique incentives for companies engaged in mining certain specified minerals or petroleum. Sections 152 and 153 provide for the taxable income of such companies to be based not on profits made but on dividends paid to shareholders. A significant saving in tax results, particularly where profits are not distributed: but the Act attempts to ensure that undistributed profits are used for further mineral exploration and development. To encourage investment in the mining industry, persons taking up shares in a company mining for the specified minerals or petroleum are entitled to a one-third deduction in respect of monies paid on the shares and used by the company for its purposes; and company shareholders may make loans to the company and write-off such loans for tax purposes to an amount of up to half their taxable income. Maximum utilisation of the tax incentives calls for careful consideration as to whether a mining or petroleum company should be financed by way of loan capital or share capital.

Jan 1, 1971

Drilling is one of the most, significant cost components of any stoping or develop- ment operation. Two of the factors contri- buting to the drilling cost are the supply and servicing of consumable items such as drill rods and bits. The purchase cost of consumable items can be controlled to a large extent by using the correct balance of quality and price. However, the service cost is a less easily controlled factor and it is in this area where potential savings are significant. In June, 1976 a six month trial period was commenced at The Zinc Corporation, Limited and at New Broken Hill Consolidated Limited with two separate suppliers supplying and ser- vicing all longhole drilling parties (one supplier for each mine) at a guaranteed cost per metre. As a result of this six month trial period a new contract was commenced in December, 1976 with one supplier supplying and servicing all longhole drilling parties at both ZC and NBHC for a twelve month period. This concept has now been in operation for over twelve months and has proved to be a significant means of slowing down the increas- ing cost associated with drilling operations.

Jan 1, 1977

By Neill B. K, Fander H. W, Wong K, Dunlop G, O&apos

Commercial interest in refractory gold is increasing rapidly. This trend is supported by the work patterns of Amdel, where, apartfrom routine process- ing of free-milling and refractory ores, the majority of testing now includes biological and pressure oxidation studies to enhance gold recoveries. Central Mineralogical Services have examined, among other ores, an apparently unique type of refractory coating. A summary is given of experience at Optimet Laboratories, Pty., Limited. Research into nitric acid pre-oxidation, underway at the South Australian Institute of Technology since 1987, has shown significant improvements in gold recoveries, and in some cases, large reductions in reagent consump- tions. Three final-year student research projects were undertaken in 1990, jointly between the University of Adelaide and the S.A. Institute of Tech- nology. These projects involved biological pre-oxidation, pressure leaching, and Scanning Electron Microscope examination of refractory ores, and the resultant pre-oxidation and cyanidation products.

Jan 1, 1991

By Williams DJ, Battino S

The rapid crushing technique for the measurement of gas content of coal consists of accelerating the rate of gas desorption from coal by crushing. This technique allows the determination of gas content in the space of hours rather than days or weeks as required for the traditional slow desorption technique. The crushing technique is used particularly when gas content determinations are urgently required for mine safety purposes. The method is now routinely used in underground coal mines of NSW and to a lesser extent in QLD. Despite the rapidity and efficiency of this method, concerns have been raised upon the reliability of the method to deliver accurate results. Experience in Australia has shown that there is in fact some discrepancy in results between gas laboratories using the rapid crush technique. The development of rapid crushing techniques for seam gas content measurements in Australia and the main causes of variability in the gas content test results were investigated. The gas laboratories participating in the gas content testing were CSIRO Division of Coal and Energy, BHP Technical Services and GeoGas Pty. Ltd.

Jan 1, 1998

By Coulter K. W

The commercial evaluation of coking coal from bore core data will begin with a technical evaluation of the coal properties affecting coke quality. Methods currently used for prediction of coke.properties from coal analysis are illustrated but in each case accuracy of measurement and prediction should be clearly understood. It is suggested that coal be initially valued from coking properties (base value) and adjusted for chemical properties (merit value). Final evaluation of coal can only take place as coke in the blast furnace where the coke is assessed under high temperature operating conditions. The commercial value of a particular coking coal will depend on many additional factors other than the technical properties.

Jan 1, 1977

Passive systems for the treatment of acid mine drainage (AMD) are typically more economic in the long term than active systems. Various flow charts for treatment selection have been prepared by scientists in the USA, however, they have typically not included a variable important at New Zealand AMD sites on the West Coast: topography and available land area. Very steep topography, dense and often protected vegetation (and animals such as snails), and a high-rainfall climate result in AMD with very high flow rates in locations with very limited space for remediation. Flow charts specific to New Zealand have been prepared which accommodate topography and available land area. Parameters necessary to use the flow charts are iron and aluminium concentrations, pH, ferrous to ferric iron ratio, dissolved oxygen concentration, topography and available land area. Prior to full scale construction, is it recommended that flow rates be quantified, small-scale trials be conducted, and cost, effectiveness, limitations, and risk of failure be reviewed for various options. One full-scale remediation system has been installed in New Zealand based on this methodology and another is planned. The performance of these systems, as well as future systems to be installed, will be used to validate these treatment system flow charts.

Jan 1, 2007

Qualitative measurement of respirable dust in metal mines is limited and an example of this is demonstrated at Northparkes Mine, where operational experience was sought for measuring dust standards and identifying exposure limits. However, relying on operational experience has limited value due to variation in observations from person to person and is based on visible dust (which is larger in size than respirable dust). However, with sophisticated dust measuring equipment, like the real-time aerosol monitor, dust concentrations can be accurately measured and recorded concisely. Research conducted as part of a collaborative agreement on behalf of Northparkes to launch an occupational dust monitoring program was implemented on the mine site. To form the basis of this research, it was hypothesised that no proper dust measuring testing at the mine site had been adequately identified. In addition, existing occupational hygiene monitoring programs did not adequately quantify employee exposures to these hazards. This project will outline the results of an occupational dust monitoring program, hence greatly improving the capacity to quantify the health risks posed to employees.

Jan 1, 2008

Carbonatites - igneous carbonate-silicate rocks - host the world's major resources for niobium, phosphorous and REE (rare earth elements).Carbonatites represent the least common products of mantle and igneous processes and their emplacement is principally controlled by lithospheric domes and rift structures. Intrusive carbonatites frequently comprise carbonate-amphibole-apatite-pyrocWore assemblages, occur as plugs, cores, dykes, sills sheets, veins, pipes and irregular bodies, are gecichemically anomalous (Ba, Ca, Cl, F, Hf, Mg, Nb, P, REE, S, Sc, SO4, Sri Tb, Ti, D, V, Zr), are associated with alkaline silica-undersaturated igneous rocks forming carbonatite complexes, and display large, intensive alteration haloes. Also carbonatites are similar to limestones, prone to weathering, and may form thick laterite profiles.Magmatic ores (pyrocWore, apatite, bastnaesite, monazite, magnetite, baddeleyite, phlogopite, fluorite, calcite) and weathering related residual and supergene ores (pyrochlore, apatite, magnetite, anatase, vermiculite) are currently being mined on all continents except Australia. Australia is underexplored for carbonatite associated primary magmatic and especially residual-supergene ore deposits. Chances are very high for the finding of new carbonatite, occurrences and associated ores.

Jan 1, 1994

By Waldram JT

The Kelsey Centrifugal Jig incorpo- rates the principles of operation of a conventional mineral jig, at the same time utilising high centrifugal forces to extend concentration to very fine heavy minerals. The main operating variables which are adjusted to control processing of different types of material are centrifugal force, ragging material and size distribution. Pilot plant trials have been under- taken to examine concentration of a mineral sand in which the heavy mineral particles occur mainly in the minus 0.075 plus 0.032 mm size range. Stage recoveries of greater than 90% were achieved at concentration factors of up to 2, although lower recoveries were obtained with higher concentration factors. A final concentrate containing 65% heavy minerals was obtained.

Jan 1, 1986

By Basillo CI

The adsorption mechanisms of various thiol collectors can be subdivided into four classes: chemisorption, EC-mechanism, catalytic oxidation and metathetical substitution. The chemisorption mechanism occurs at potentials below the thermodynamic potentials for the metal-thiol compound formation and is reversible. The EC-mechanism occurs when the mineral is sufficiently oxidised to liberate metal ions to form metal-xanthates; therefore, it is observed with more easily oxidisable minerals and/or with collectors having large pK values. Thionocarbamates adsorb on sulphide minerals via the EC-mechanism due to their large pK values. Although the adsorption occurs at very low potentials as compared to xanthates, it is irreversible with large overpotentials. On the other hand, the adsorption of modified thiophosphates and thiophosphinates occurs near the thermodynamic potentials because of the low pK values. The metathetical substitution is believed to occur only when a mineral is highly oxidised. These classifications are useful for studying the effects of electrochemical potentials and the molecular structure on the collector adsorption Mechanisms.

Jan 1, 1993

By P Mavros, K A. Matis, N K. Lazaridis

A large number of techniques are in use today to limit membrane fouling, among them certainly is air bubbling (which constitutes the transport medium in flotation) as applied in wastewater treatment; meanwhile, dispersed-air flotation is suitable as a pretreatment stage for microfiltration. The invented and investigated hybrid cell combines the advantages of both flotation and membrane separation, while overcoming their limitations, producing clean water from industrial wastewater. Metals recovery from dilute aqueous solutions is a promising application of this innovative hybrid process of flotation and microfiltration, further to solid/liquid separation. In this study, ceramic flat-sheet membrane modules were inserted inside a typical flotation cell in the laboratory tests, using multichannel geometry, combining flotation with microfiltration by submerged membranes; the latter requiring periodic backflushing. The specific objective was to apply this process for the efficient separation of effluents containing metal cations (here, zinc). The main examined parameters were: the initial metal concentration, flotation surfactant applied and air flowrate. The successful contribution of precipitate flotation was highlighted, while the observed metal removals were of the order of ~100 per cent.

Jan 1, 2005

Geosynclines have been well studied for many years, but very little has been written about the concepts of sedimentary basins in spite of the vast amount of data available. They have been regarded, perhaps, as well- understood intuitively, and therefore not worthy of study. Many of the fundamental concepts of geology were developed during the 19th Century with the construction of coal mines, canals and railways. It was a happy chance that led railway engineers in the early days to think that trains could not climb any but the smallest gradient, so, in Britain at -least, numerous railway cuttings and tunnels were made. These exposed to view and study, in a better form than Nature usually provides, a great deal of interesting geology. Because of the lack of literature about the concepts of sedimentary basins, it is not possible to be sure what the early geologists thought. It seems that sedimentary basins were regarded as recording a history of subsidence during the early stages, when a transgressive sequence accumulated; and a history of uplift during the later stages, when a regressive sequence accumulated. It seemed axiomatic that the age of folding and faulting was younger than the rocks folded or Faulted.

Jan 1, 1987

By Whitehead A. B

INTRODUCTIONDuring the past few years there has been considerable interest in developing the so-called direct reduction processes for treating iron oxides. The various methods proposed were recently reviewed by Scortecci and Palazzi (1960).In particular the application of fluidized bed techniques received considerable attention and, on first examination, this seems to be the ideal method 'of dealing with fine iron oxides. Several difficulties (e.g. product agglomeration) require the method to be investigated further before its potentialities can be fully assessed.PROPOSED FLUIDIZED BED REDUCTION PROCESSESBrassert and De Jahn (1951) were among the earliest to suggest the use of fluidized beds for the reduction of iron ore to metallic iron. Their patent was followed by many others proposing similar concepts, mainly from Lewis (1955), Ogorzaly (19.56), Shipley (1956), Agarwal (1960'), Osborn (1958), Texaco Development Corporation (1956) and Stelling (1957).The H-iron process (Squires and J ohnson, 1957; Lubker and Bruland, 1960) is the only scheme that has been an economic success. This process, mentioned later, manufactures a 'premium quality product in the form of sized iron powder.AIM OF THE PRESENT WORKThe work reported here was performed to assist in the formulation of a comprehensive pl'ogramme of research into fluidized bed reduction processes to be undertaken at the...

Jan 1, 1962

By P Lilly

Blasting is the primary comminution process in most mining operations. This process involves the highly complex and dynamic interaction between two main components. The first is the detonating explosive and the second is the rock mass into which the explosive is loaded. The mechanical properties of the rock material (such as dynamic strength, tensile strength, dynamic modulus and fracture toughness) are important considerations in understanding the blasting process. However, it is the characteristics of the geological defects (joints, foliation planes, bedding planes) within the rock mass that ultimately determine how effectively a blast performs in terms of fragmentation, all else being equal. The defect characteristics include, but are not limited to, their orientation, spacing, and mechanical properties. During the blasting process, some of the geotechnical characteristics of the rock mass are substantially changed. From the blasting outcome point of view, the most notable and important is the change in fragment size distribution that the rock mass undergoes. The pre-blast in situ defect-bounded block size distribution is transformed into the post-blast muckpile fragment size distribution. Consequently, it is fundamental to our understanding of and ability to predict the blasting process that both the blastability of a rock mass and its transformation into the fragment size distribution can be appropriately quantified.

Jan 1, 2001