Search Documents

By Lane D. P, Malone J. G

The slag fuming furnaces are the major bottleneck in the BHAS zinc production flowsheet. Intensification of the fuming process could significantly reduce this production restriction. Oxygen enrichment was proven to be a means of intensifying the fuming process. This procedure resulted in higher slag bath temperatures, and development work was undertaken towards obtaining accurate slag bath temperature measurement and control. Slag bath temperature measurement techniques were evaluated, with infra red optical pyrometry established as the system with the most potential for continuous temperature measurement and control. Oxygen enrichment resulted in a zinc production capacity increase of 1 000 tonnes per year. An oxygen enrichment technique was developed which both minimized the risk of furnace damage and made the most efficient use of the enrichment oxygen.

Jan 1, 1989

By M Devia, J Rapkoch

This paper is intended to help design engineers, operating staff and plant managers understand the principles of metallurgical gas handling systems design. It also explains operating, safety and energy savings issues that the designer should take into consideration in the design of process off-gas systems for sulfide smelters. Primary smelting reactors, converters, and other off-gas sources impose challenging duty requirements on the various components of the gas handling systems. This paper reviews the design of common system components including the hood for gas capture at the system inlet, gas conditioning, gas cleaning, ductwork, dampers, hot gas fans, and the appropriate use of instrumentation and controls. The engineer must also be aware of how ductwork system effects and heat losses influence system performance. Also, the analysis of a recently-designed gas handling system will be reviewed, which includes high-strength SO2 gas from a smelting reactor, asymmetrically located Peirce-Smith converters, and a gas mixing chamber to mix the gases before they are sent to two acid plants of different sizes.

Jan 1, 2005

By Lumley G. I, Duffy W. J

The risk involved with incorporating new/unfamiliar technology into mines has, in the past, largely been evaluated by the supplier of the technology. The implications on safety and productivity has been accepted as part of the process of `getting up and running'.This has changed. As companies see the lost productivity and accidents actually costing significant dollars, risk assessment is becoming an important part of the implementation of new equipment. Regulatory authorities are also seeing the preventable incidents and in some cases are now requiring a risk assessment to be undertaken on new equipment at a Mine.

Jan 1, 1992

By Pollard D. M

The removal of nickel from lead by sulfur drossing was investigated using a technique which models industrial batch decoppering practice. Successful denickeling to 0.005% (Ni)pb was consistently obtained in the absence of silver, well below the experimental equilibrium value of 0.015% but still above levels obtained in industrial practice. Silver appeared to have little effect upon denickeling. The final nickel content was dependent upon the initial nickel content, the total sulfur addition and the stirring time. The presence of nickel was found to give no assistance to successful decoppering. Simul- taneous removal of nickel and copper was observed at silver contents in excess of 0.02%. Extended stirring resulted in a further lowering of the nickel content but reversion of copper to the bullion was observed. Experimental work has shown that nickel can be removed by a standard decoppering operation; a procedure which is used in secondary lead re- fining. Alternatively nickel can be removed during initial decoppering in primary lead re- fining operations.

Jan 1, 1987

By E Villaescusa

This paper describes a methodology for the design of mine pillars at the McArthur River Mine. The pillar strength is calculated using a method that accounts for confinement, pillar geometry and intact rock properties. The average pillar stress was calculated using in situ measurements of vertical stresses at shallow depth and the tributary area method in conjunction with numerical modelling. Observations of pillar behaviour indicate that an existing pillar stability graph may be slightly conservative and further adjustments for the local rockmass conditions are needed. The results to-date indicate that all mine pillars are stable for a range of mining geometries at McArthur River Mine.

Jan 1, 1998

By Jimbo I, Ogawa O

A series of experiments was carried out to investigate the solubilities of copper, arsenic, antimony and bismuth in silica-saturated iron silicate slags under controlled oxygen partial pressures at 1200 and 1250¦C. Molten copper containing each of the above elements was kept in contact with a slag in a silica crucible for 24 or 48 hours to attain equilibrium. No me- chanical entrapment of metal into the slag was observed. The appearance of the magnetite phase in the slag was avoided by holding oxygen potentials at substantially lower values than that evaluated from available data on iron silicate slags. Solubilities of copper, arsenic, antimony and bismuth in slags were plotted against oxy- gen potentials and both oxidic and atomic types of dissolution were found, except in the case of arsenic, from the dependencies of the solubili- ties on the oxygen potential and from positive intercepts of regression lines when extra- polated to zero oxygen potential. The dissolu- tion of arsenic seemed mostly oxidic. Distri- bution coefficients of arseò,ic, antimony and bismuth between copper and slag are also Discussed.

Jan 1, 1980

By A Weeks an, R Bertinshaw, S Khosrowshahi

Good mining is central to any approach to value tracking. Good mining occurs where the ore is correctly delineated, measured and fed to the mill. This process is usually referred to as grade control, ore control or quality control. There are now ways to measure the efficiency of this process, such as by using conditional simulation, and a brief synopsis is presented. Resource estimation is the foundation of ore reserve estimation, which should enable useful prediction of the expected metal to be recovered from mining and milling. Significant improvements have resulted from applying new techniques such as the Chain of Mining (CoM) method, which models the mining process. Again, a brief synopsis is presented. Tracking value from the mine through the mill implies a linear sequence of processes that can be modelled. Reality is more complex and there are error components, feedback loops and breaks in the Chain of Value. Modelling the total production process in a number of operations is considered, including the various impacts on producing reconciliations. Procedures are also discussed for handling a number of difficult issues such as: different data supports, stockpiling strategies, blending from multiple ore sources, blast movement and underground ore extraction.

Jan 1, 2002

By M Scoble, R A. Hall

The mining industry has aggressively sought competitiveness through increased productivity and return on investment. A primary strategy has been the pursuit of economies of scale. This has also been dependent upon the implementation of new technology and systems integration. System integration has been accomplished through the implementation of mine dispatch, global positioning and mine wide communication technologies. These technologies have tended to advance at different rates of development and implementation. The result has been that across the industry, and even within companies, mines are at various stages of operational system re-engineering in these areas, driven by improvements in productivity and operational efficiency. Although this strategy has been successful, little effort has been made to analyse change in operational performance in order to understand and model the effects of scale in a quantitative manner. This paper considers the particular impact of equipment scale, together with potential future trends. It then presents and demonstrates a preliminary method to quantify through simulation the anticipated benefits of economies of scale.

Jan 1, 2003

By S Pfaff, R Rajic

In the case when the number of independent variables is greater, a careful design for carrying out tests has to be made in order to obtain, with the smallest possible number of tests, as much as possible neutral information about the influence of independent variables on the dependent ones. Only on the basis of such design and its statistical analysis it is possible to come to right conclusions about the function of the whole system. The influence of pressure, temperature, humidity and granulation of the coal upon the resistance to pressure and the water absorption of the briquettes has been tested, with the aim to examine how each of the two dependent variables changes depending on the values assumed by any of the four independent variables and which of the mentioned independent variables significantly influences the dependent ones. The full factorial design with 16 experiments and the central composite design with 27 experiments have been applied. The influence of the independent variables upon the dependent ones has been examined by applying the analysis of variance. The influence values of individual factors and their interaction upon the dependent variables have been stated as well as coefficients of curvilinear equation.

Jan 1, 2003

By H Park, V Sahajwalla

"Due to the increasing amount of gangues in iron ores, a beneficiation process is required more as a preliminary step for ironmaking process. However, mechanical grinding and washing of iron ore needs tremendous effort that increases operating cost. Therefore, there is a necessity of a novel approach to ironmaking which can tolerate considerable amounts of silica or alumina. In the present study, a high alumina-carbon composite pellet was examined for an ironmaking process. The effect of compositional changes in the CaO-FexOy-Al2O3-SiO2 oxide system on the reduction of carbon composite pellets was investigated in a purpose built thermo-gravimetric analyser (TGA) at 1473K (1200¦C). As a result, alumina increased the reaction rate of carbon composite pellets by increasing surface area, while silica decreased the reaction rate by lowering surface area of samples. Infrared gas analysis assisted with the reaction kinetics of carbon composite pellets through measurement of CO and CO2 in off-gases. This study will assist with establishing the new pelletising method which differs from the conventional fluxed pellets.CITATION:Park, H and Sahajwalla, V, 2013. Effect of CaO-FexOy-Al2O3-SiO2 oxide system on the reduction of carbon composite pellets, in Proceedings Iron Ore 2013, pp 467-472 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By P Bourke, S Ronkainen

Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technicianÆs job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always other problems to attend to. A considerable amount of work has thus been done to develop a æsystemÆ that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterÖ instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability. Three FrothMasterÖ units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:to control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other; control of the concentrate grade (per cent copper) from the first rougher; reduction in the frother consumption in the rougher circuit by monitoring the froth speed. A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions: Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint. Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time by the OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore. The results from a 21-day trial have shown the following:The ratio of concentrate mass-recovery between two cells in series on the same level has been successfully balanced, thereby overcoming problems due to differences in hydrostatic heads. It is possible to control the speed of the froth, in mm/s, to within five per cent of its setpoint using the aforementioned manipulated variables. It has also been shown that, for reliable control, it is necessary to control more than just one variable (eg level or air). The grade of the first rougher concentrate has been controlled to within 0.3 per cent of the grade setpoint for long periods of time, which has important implications for the circuit recovery. The frother consumption has been reduced significantly. This paper will thus show that substantial progress has been made to demonstrate the value of using on-line froth speed measurements in flotation plant control to obtain real financial benefits.

Jan 1, 2000

By Donald D

A number of standard tests are conventionally carried out to characterise strength properties of rock. The values of the parameters obtained are often affected by planes of weakness or defects in rock structure. For the purpose of mine design, the range in values or the class of the strength (obtained from a number of tests) is generally more important than a precise value (obtained from a single or limited number of tests). Research has been conducted to establish a relationship between an indentation index and the strength of the intact rock material from the Eastern Goldfields of Western Australia. The Tamrock Raise Boring Index (RB-i) test, which is quick and easy to perform, was selected as the indentation test. The results show that, for heterogeneous, strong to very strong rock, there is a good correlation between the indentation index and the uniaxial compressive strength and tensile strength.

Jan 1, 1996

The word "optimization", refers to the search of an economic optimum, or, more precisely, to the choice of technical parameters which will define the more profitable mining project, knowing the values of the economic parameters. In fact, there is no direct way to perform this optimization, because the extremely large number of technical factors involved, from the type of working and its selectivity to the characteristics of the mill and its flexibility, makes it impossible to make a comprehensive survey of all possible projects. Beside, it would be meaningless to engage in such a task as the deposits themselves are not really known, but only estimated, with sometimes a high level of imprecision. Not to mention the numerical instability which would affect such a computation! In addition, the "best" project is not necessarily the one which strictly maximizes a given profit formula. There also exist human factors which have to be complied with, when choosing the cutoff grades for instance. Finally, there are other non-numerical factors which interfere with the choice between several projects: the shape of the bottom of a pit of the layout of the access road for instance.

Jan 1, 1986

Throughout the Kalgoorlie Field the dominant factors influencing all planned exploratory work are: firstly, the general geology of the district, and, secondly, the lode fracture pattern. Superimposed on these, there are innumerable faulting problems which tend to complicate the search for ore.In this paper it is proposed to deal primarily with the lode fracture pattern and to touch on the general geology only insofar as it affects ore distribution. So much has been written on Kalgoorlie geology that it would be impossible to review the literature adequately in a brief paper such as this. The basic facts of rock types and rock distribution are well established and the broad structure of the field is known in the central portion, though it is less well established towards the northern and southern ends.The latest descriptions of the general geology are those of Stillwell (1), and Gustafson (2), -and these represent the basis of current knowledge.GENERAL GEOLOGY.The field is six miles long and about one mile wide, the long axis trending north-west. The "Golden Mile," or heart of the mining 'area, covers a length of three miles in the southern section, and consists of a central core of quartz dolerite greenstone which merges into uralitic quartz 'dolerite on its western margin. The uralitic quartz dolerite is derived from an original quartz dolerite by a low grade...

Jan 1, 1948

By J B. Farrow

The AJ Parker Cooperative Research Centre for Hydrometallurgy carries out research on behalf of, and in collaboration with, the Australian mining industry. As might be expected, much of its research is directed towards improving the efficiency of alumina and gold processing plants. However, the Centre also carries out research of relevance to base and other metal producers. A key element in its work is the successful transfer of its technology to the companies with which it is working. In general, this is achieved in the following five steps:definition of the problem through discussions with the company commissioning the research; execution of the research; assessment of the research findings; testing of the research findings by pilot plant or on-site trials; and implementation of the results on the full-scale. This pattern is exemplified by the work carried out by the Centre to improve the performance of gravity thickeners which are used throughout the minerals industry for solid-liquid separation. The research has focussed mainly on ways to optimise the use of flocculants (long chain polymers) to enhance thickener performance. It has been shown that the way the flocculant is mixed with the slurry is of profound importance. Computational fluid dynamics modelling of the feedwell region of thickeners and laboratory and plant flocculation studies have been used to determine better ways to contact the flocculant with the feed slurry. Implementation of these and other findings on the full-scale confirmed that improvements in thickener performance were indeed possible. As a result of this AMIRA funded thickener technology work, there have been considerable savings to a number of Australian mineral processing companies, through improved operation, higher throughputs and flocculant savings.

Jan 1, 2000

Two significant TBM boreability predic- tion models are outlined. Predicted advance rates are compared with actual advance rates taken from twenty case histories. The results show that a simple low cost method that uses one machine parameter and one rock parameter compares very favourably with a high cost sophisticated method which also includes information regarding discontinuities in the rock mass. The effect of rock texture on drillability is also examined. A method of quantifying rock texture has been developed and is outlined. Experimental results show that the developed TEXTURE COEFFICIENT returns highly statisti- cally significant correlations with drilla- bility data in a wide range of rock types.

Jan 1, 1987

With the use of 36 rock drills of the jackhammer type at the West Lyell Open Cuts of the Mt Lyell Mining & Railway Co, it is of importance to determine the economic as well as the physical life of these machines. With this purpose in mind records have been kept of the footage bored and the cost of new parts placed in each machine, and the following procedure adopted.A graph is plotted for each machine showing the footage bored as a horizontal line and at each 5000 feet of boring the total cost of new parts is noted on this line (see Figure 1). Thus at a glance it is possible to see the amount of work done by each machine and the money spent on it in new parts. However, it is difficult to visualise from this graph the increase in the cost of new parts for each machine as its life advances. To obviate this clifficulty a curve is plotted with the cost of new parts as the vertical component and the distance bored as the horizontal component.As before the cost of new parts are taken at each 5000 feet bored (see Figure 2).

Jan 1, 1994

With the post-war expansion of mmmg activities on its Western group of mines, the management of Lake View and Star Limited has commenced a project for the improvement of underground ventilation.The major part of this project is to provide adequate return airways for the ventilation of the deep levels. To this end, the Ivanhoe South Extended shaft is being enlarged, and ultimately an exhaust fan with a capacity of 180,000 cu. ft. of air per minute will be installed at the shaft collar.Prior to 1932, the shaft was used exclusively for baling water from the 800 and 2,000 ft. levels. These two levels are the only ones connected to workings from the Horseshoe lease. After the installation of pumping plant at the Horseshoe Main Shaft, baling was discontinued, and the water was graVitated from dams to the pumps on the 1,000 and 2,000 ft. levels.Water makes into the shaft, through a series of fault planes, between the 600 and 1,500 ft. horizons. The total flow is 16 gal. per minute, of which approximately 7 gal. per minute graVitates to the 800 ft. level. As a big proportion of the water dropped uncontrolled through the shaft, a downcast current of air approximating 20,000 c.f.m. was induced. This air ventilated a limited area of workings in the Horseshoe lease, between the 2,000 and 2,360 ft. levels.In 1938, it was decided to reverse the direction of the airflow in the shaft. Work was carried out to pipe the...

Jan 1, 1948

The techniques used by the State Electricity Commis- sion of Victoria to handle and store brown coal in the both the raw coal and boiler bunkers are outlined. These tech- niques were adopted in agreement with the science of modern bulk solids handling. By successful balance between practical requirements and bulk solid handling system design require- ments the Commission expects to confidently attain reliable coal flow even for the most adverse of coal flow properties. Attainment of this goal demanded full attention to channel detail selection. An outcome of this attention has been the development of a novel bunker and discharge arrangement for handling extremely difficult to handle coals. Due to the novel features of this slot bunker outlet arrangement it's ad- vantages and disadvantages are discussed.

Jan 1, 1987

By Fengyan D

Removing the interference of latter events, the data of geophysical (such as gravity and aeromagnetic) anomalies may indicate whether the mobile belt exist and whether the adjacent terrains of the mobile belt originally belong to one single unit. The petrotectonic assemblage can provide informations about the tectonic setting where it was generated from. The structural style can exhibit the kinetic and kinematic processes. The form of ancient isogeotherm may reflect the ancient geothermal regime which is related to the tectonic mechanism. In general, the early Precambrian terrains suffered polymetamorphism and multiple structural deformation. The researches must be carried out for the distribution of paleogeotharm and m.tamo'phic facies and zones on the basis of recovering the early structural style with structural analysis method; then a relatively correct conclusion may be geined on the ancient geothermal regime. This method can be known as "Ancient Thermotectonic Analysis". Through the sythetical research, a real knowlege about the tectonic setting of early Precambrian mobile belt can be obtained.

Jan 1, 1990