Search Documents

By Wood P. D, Pettifer G. R

In the upper coal surface in the Latrobe Valley, craters known locally as fireholes have developed due to prehistoric coal fires. They can be several hundred metres across and up to fifty metres deep, and are now filled with overburden materials varying from hard baked clays to very soft lacustrine clays. In addition to reducing coal reserves, continuous mining operations are seriously affected by fireholes. Large undulations in the upper coal surface result in a mixture of coal and overburden on the upper mining levels. The very soft lacustrine clays are unstable in the mine batters and the overburden dump, are difficult to handle on the bucket wheel excavator/conveyer system, and have insufficient bearing capacity for the large bucket wheel excavators. Early identification is essen- tial and both drilling and dynamic core penetrometer have been exten- sively used. However, this has not proved adequate in locating and defining the extent of all fireholes, due largely to their irregular shape. To overcome this a range of geophysical techniques has been trialled with very promising results. A trial area has been covered on a twenty metre grid using gravity and Geonics EM34 conductivity measurements and the same area has been covered at a closer spacing with high resolution magnetics. Image processing of contoured magnetic, EM34 conductivity and residual gravity data has resulted in very good correlation with drilling data.

Jan 1, 1989

By A B. Richards

Effective control of blast vibration and flyrock requires that significant factors be identified and quantified, that the blast be designed to ensure both blasting efficiency and compliance with applicable limits, and that the blast design be effectively implemented by field personnel. Significant factors contributing to ground vibration and airblast are: charge mass; distance and direction relative to the blast; drilling design: burden, spacing; stemming height and material type; hole diameter and depth; and initiation sequence and direction.In addition, airblast may be strongly influenced by shielding and meteorological conditions. Ground vibration is also influenced by the transmission characteristics of the ground and soil. Flyrock throw is determined by charge mass, burden, stemming height, blasthole diameter and depth. The contribution of each of the factors has been quantified and models developed to enable the environmental outcomes of blast design to be predicted. Environmental blast design is necessary to ensure compliance with regulatory limits and the implementation of æsafeÆ exclusion zones for flyrock clearance. This paper discusses the models used for environmental blast design and demonstrates the often significant effects that lapse during implementation of the design can have on predicted outcomes. In practice, drillers and shotfirers are sometimes confronted with situations that require modifications to the blast design to cope with the real site situation. Methods are presented that may be used by drillers and shotfirers to evaluate the effect of these modifications, the tolerances that must be reached during their work practice and checking procedures, and the consequences of their actions.

Jan 1, 2004

Renison Limited produces high and low grade tin concentrates at an annual rate of 5000 tonnes of contained tin metal. In spite of the fine average cassiterite grain size, emphasis is placed on gravity concentration methods to produce a high grade final product. Cassiterite flotation is considered and operated as a gravity circuit scavenger responsible for approximately 15 percent of recovered tin metal as a fine grained low grade concentrate. Metallurgical problems mainly result from ore-type variations which may be aggravated by a number of circulating loads. The rationalisation of circuitry is being studied to provide more effective control by operators and to allow exploitation of current control and modelling techniques.

Jan 1, 1977

The Ramu chromite deposit occurs in the Marum Ophiolite complex and is the most economically attractive chrom-ite deposit in Papua New Guinea. Its lateritic nickel, chromite and cobalt potential has attracted several compan-ies to prospect the deposit.In the present work, the compositions of chromite in the Ramu lateritic deposit and coexisting olivine-chromite pairs in Marum Ophiolite dunite were analysed with the electron microprobe for Fe, Mg, Cr and Al. The results were used to determine the relationship between the cations in the tetrahedral and octahedral structures of the chromite. In addition, the Fe, Mg, Cr and Al cations of the coexisting olivine-chromite pairs were used to calculate the equilibrated temperatures of crystallisation of the chromite. The variation of Fe", Mg and Cr cation values of the chromite in relation to the calculated temperatures was studied by regression analysis.

Jan 1, 1994

By Aspinall T. O, Bell L. C

Increased awareness and stricter enforcement of regulatory requirements for adequate rehabilitation of surface mining sites has made environmental planning an essential part of strip mine planning. Rehabilitation is site specific and should be based on data which relate to that site. Cost-effective spoil pile design to minimise erosion is an important part of rehabilitation. Spoil pile design is an integral part of strip mine design. QCT Resources Limited has provided a postgraduate scholarship toward research in this area. The controlling factors of spoil pile design are post-mining land use, drainage requirements and degree and rate of erosion. The extent to which mine design is controlled by these factors is determined by regulatory requirements. To plan acceptable rehabilitation programs, erosion processes must be accurately modelled, and a range of erosion prediction models are available. Useful prediction models can be placed in two categories with the first category containing soil loss prediction models which can be used to predict the amount of soil lost from an area over a short or long term basis. Models in this category include the Universal Soil Loss Equation (USLE), Water Erosion Prediction Project (WEPP), Griffith University Erosion and Sedimentation System (GUESS) and Chemical, Runoff and Erosion from Agricultural Management Systems (CREAMS). The second category contains topographic evolution models which give an indication of the long term morphological development of a formed surface subjected to erosion processes. Models in this category include "Topog", Willgoose's Physically Based Catchment Evolution Model and Areal Nonpoint Source Watershed Environment Response Simulation (ANSWERS). The USLE has been used in the agricultural field for soil loss prediction. To apply the equation to mine sites in Central Queensland, it is necessary to understand the factors affecting erosion at the sites. This understanding should allow the variables of the equation to be quantified. The rainfall factor applied in the USLE is independent of engineering design or soil management techniques. The factor of spoil erodibility is dependent on the material's physical and chemical properties and can vary from site to site. In the equation, the topographic factor, cover and management factor and conservation practices factor can be varied by design to reduce erosion on rehabilitated areas.

Jan 1, 1991

The late 1960's and 1970's saw the initial development of the coal resources of the Bowen Basin of Queensland. The projects developed relied on large scale, open-cut operations using draglines for overburden removal and, in the majority of cases, project viability could be established based solely on those open-cut operations. Many of the mines developed in the 1980's have the same characteristics.Unlike these mines, the German Creek Mine has limited open-cut reserves at low overburden to coal ratios, and planning of the complex involved a large open-cut mine capable of developing early cash flow, with phased introduction of underground mining to replace open-cut capacity as the strip ratio increased.

Jan 1, 1985

By Real F, Carvalho P

During the development of the Neves-Corvo Underground Copper Mine, since 1981, inflow of water has been encountered in the mine workings, which consist of a ramp from surface 5 km long, a shaft 575 m deep and access crosscuts through the massive sulphide orebodies of Neves, Corvo and Graga, which are three of the four known deposits up today. Mine-hydrological studies have established the main characteristics of the hydrological system and its evolution in space and time. In a geological setting of low permeability rocks of Paleozoic age, tectonically affected by thrusts and faults, this has involved consideration of the relation with surface and ground water as a result of mine dewatering processes. The hydrological systems are described and summarized in this paper together with the techniques employed to study their origin and evolution, namely hydrochemistry, thermometry, piezometry and isotopic tracers.

Jan 1, 1988

By Galecki G

The investigations conducted in the High Pressure Lab at the University of Missouri-Rolla demonstrated the ability of high pressure waterjets to excavate coal and minerals, disintegrate materials and as well as to comminute coal and minerals. Additional progress in comminution can be achieved if the compressive crushing principle commonly used at present is changed to one where particles are fragmented by the tensile growth of preexisting internal flaws or cracks, under internal waterjet pressure. This idea was studied in a number of tests. It covers tests with different jets imposed on coal and rock samples during compressive load as well as without any loading.

Jan 1, 1993

By Alford R. A

The causes of the loss of heavy mineral from mineral sands wet concentrators were identified through detailed surveys of two such concentrators. It was found that tray and spiral sluices preferentially lost elongated panicles, but panicle size had little effect on loss. Recovery was shown to increase with panicle density. The major influences on the recovery efficiency of individual concentrating devices (stans) were feed rate and feed grade, recovery increasing with decreased feed rate and with increased grade. Uneven distribution of total solids and heavy mineral to individual stans contributed to losses through the corresponding effects in feed tonnage and grade. Computer simulation demonstrated that significant recovery improvements could be obtained by appropriate adjustment of splitters to optimise the characteristics of internal plant flows.

Jan 1, 1991

By Kazis JV

The beneficiation of fine coal has been the major problem facing the coal preparation engineer in recent years. The influence of clay slime, particle size and reagent type are but a few of the many factors that affect the recovery of fine coal. Laboratory test work has indicated that substantial increases in recovery could be achieved by improvements in technology in all these areas. Unfortunately, in most cases this technology has not carried through to the operating plants.

Jan 1, 1984

By Williams D. J

The boundary element method is one of a number of tools that have found wide application in geomechanics for mine design and stress analysis. Two examples are presented in this paper, illustrating the use of the boundary element method to find potential problem regions in large-scale excavations. These examples are from a Papua New Guinea open cut mine and an Australian sub-level caving operation. Because of the scale of the mines and the complexity of the excavations, the boundary element method is the only practical numerical modelling technique to account for the major influences. Although the boundary element method uses only linear elastic models of the rock mass, the paper illustrates techniques for dealing with non-homogenous and anisotropic rock masses, as well as clasto-plastic effects associated with an excavation.

Jan 1, 1995

The Mt Todd Project is located 42 km northwest of Katherine in the Northern Territory. The identified mineral resource estimate for the Batman gold deposit is 66.7 million tonnes (Mt) grading 1.4 grams/tonne (g/t). Proved and Probable Ore Reserves total 42.3 Mt grading 1.5 g/t. Orebody definition and reserve estimation is based on extensive percussion and diamond drilling. Exhaustive bias analysis comparing grades produced from different drilling techniques has been undertaken. Similarly, detailed check assaying programs have been run to validate grade data produced by commercial laboratories used during the exploratory drilling phase. Significant biases were established from both studies and appropriate 'corrections' were made to drillhole databases prior to final resource and reserve estimation. 3D geostatistical modelling has been utilised for resource and reserve estimation, with specialist consultants contracted for this work. At all times, interpreted geological controls on mineralisation, provided by

Jan 1, 1994

By Wong KY, Woodcock JT

Previous results have shown how con- trolled-potential sulphidization (CPS) can give improved metallurgy during rougher flo- tation of mixed oxide-sulphide copper ores. Results in this paper, using different samples and different equipment, confirm the previous results and extend the application of CPS to cleaner flotation. By using CPS, faster flotation of copper minerals (chalcocite and malachite) from clay was obtained in roughing and cleaning, and improved concentrate grades and recoveries were achieved over those by conventional manual control. The optimum sulphidizing potential (i.e. the potential of a sulphide ion-selective electrode versus a saturated calomel electrode) was -500 mV, and could be controlled to ¦5 mV, during four rougher- scavenger and three cleaner-re cleaner stages. This optimum gives the best balance between copper recovery, concentrate grade, and sodium sulphide consumption. Five cleaning circuits and five ore com- posites of different composition (0.55-1.50 per cent Cu) were examined as well as the effect of feed size and pulp density. Better results were obtained at 20 per cent solids in a Denver cell than at 33 per cent solids in an Agitair cell; this may have been related to the high clay content of the ore. Commercial equipment for pilot plant or full-scale plant application of CPS is cur- rently being developed.

Jan 1, 1986

By Bassett N

The Eneabba deposit, located 280 km north of Perth, Western Australia, and 30 km inland (Fig. 1) is one of the most recently developed deposits of mineral sands in the world. The area has been in production since 1974, while the Associated Minerals Consolidated Limited (AMA) operation commenced production in 1976. Total ore reserves of close to 400 million tonnes contain about 40 million tonnes of heavy minerals (proved and probable).

Jan 1, 1979

The development of present methods of pillar extraction has evolved from the very earliest of hand mining operations which were limited in scope by venti- lation and transport considerations. Conservation and safety considerations also have led to the current shortwall operations with conventional equipment and powered supports. The shortwall methods have had significant effects on safety, costs, con- servation, flexibility, and other aspects of pillar extraction. The present stage falls short of the ideal but is some guide to prediction in what direction may lie the ideal methods for the future.

Jan 1, 1974

Cyanide-extractable gold is far more meaningful in the definition of ore, and control of extraction, than fire- assayable or aqua regia digestible gold. The use of cyanide- extractable gold addresses the significant problems of over- as well as under-assaying by fire and aqua regia digests. The problems of conventional control or diagnostic cyanidation extractions: lengthy extraction, and masking by pregrobbing in cyanidation extractions for assay purposes; are surmounted with a novel activator - Leach WELL. Full extraction of liberated gold, insignificantly affected by preg-robbers, can now be achieved within 30 minutes. This can assist in reducing common gold losses presently often hidden by inappropriate mine call factors, and/or high grade cut values. This paper includes a discussion of fundamental mechanisms of cyanidation, preg- and assay-robbing, which underlie the phenomena Involved.

Jan 1, 1992

Methane predrainage from coal seams in the Western Area of the U.K. has been practiced over the past decade. The differing reasons for the practice include the controlling of gas emission rates in coal headings required to win out coal faces and also the need to control the gas emission rates in the roadways of retreat faces in order to comply with the statutory requirements. There are some similarities with predrainage experience in the Bulli Seam NSW. The several case studies highlight the varying conditions in the Western Area coalfield where the use of predrainage was Required.

Jan 1, 1982

By Rowley M, Bradford P

Plutonic Resources Limited (formerly known as Pioneer Mineral Exploration Limited) delineated, developed and operates the Plutonic Gold Mine located 180 kms northeast of Meekatharra, Western Australia. Gold mineralisation was discovered in the Marymia greenstone belt by Great Central Mines NL (GCM) in 1988. There was no previous, recorded gold mining activity in the area. In May 1989, Plutonic Resources Limited (PRL) entered into an agreement to acquire a 51 per cent interest in the three Mining Leases containing the Plutonic deposit from GCM. Subsequently in December 1989, PRL acquired the remaining 49 per cent interest in the Mining Leases. PRL and GCM are also involved in a 51:49 regional joint venture on extensive Exploration Licences in the vicinity of the Mining Leases. Following due diligence validation, reserve delineation and testwork, a feasibility study was undertaken in conjunction with JR Engineering Services, which led to the financing and development of the project for operation in August 1990.

Jan 1, 1991

Formed in 1965 to investigate the bauxite deposits on the Gove Peninsula, in the Northern Territory of Australia, Nabalco Pty. Limited undertook to determine the feasibility of establishing a mining operation and alumina plant of at least 500 000 tonne/year capacity. The drilling programme undertaken and the analytical methods, assumptions and criteria used to define practicably extractable bauxite are described. The ore characteristics and the interpretation of results used to evaluate the reserves are detailed. The operating techniques developed in mining ten per cent of the reserves and variations experienced between indicated and actual mining are examined and discussed.

Jan 1, 1979

By Toro HCH, Von Borries GH

A brief description of the semi-autogenous grinding (SAG;) facilities of Compania Minera Disputada de Las Condes is given. A data-logging and computer system was connected to the plant inter facing the existing analog control system in a supervisory s, control philosophy. The development of a control straiov,v t,) maintain maximum power of the SAG mill atsubjected to process restrictions is shownThe present control scheme is discussed inalgorithm was designed based on correlations onLween vartaoles. Associated with this, a direct level of control was developed be, on classical control algorithms, process inter-active tuning has been included. Also, an algorithm to prevent overloading of the is discussed. Control scheme tests are presented in comparison t manual operator control under the same conditions. It is shown t the control strategy gives a more stable operation and a higher plant throughput.

Jan 1, 1985