Search Documents

By R L. Koenig

Previous papers at Metplant conferences have covered the options for crushing and grinding circuit selection. High Pressure Grinding Rolls (HPGR) may have considerable advantages over autogenous milling circuits but test work and evaluating different grinding circuits must be done to establish which circuit provides the best option. The Hawsons low grade magnetite project provides a specific example in using thorough test work, careful simulations and detail in design to allow the evaluation of grinding circuit performance. Fortunately tools are available for this evaluation and the test work for the Hawsons iron ore is detailed in this paper. The results of the test work and simulation indicates that although the Hawsons iron ore is competent in terms of autogenous milling given the medium hardness of the ore in the Drop Tests, the HPGR testing indicates that the use of HPGR is likely to use half the energy requirement. This is a characteristic of the Hawsons iron ore and is likely to be valid for other iron ores in the Braemer Iron Formation which stretches from the Hawsons lease in New South Wales to Razor Back and South Dam in South Australia. The Hawsons magnetite iron ore resource has been known from the early 1960s when CRA explored the area. However, the Pilbara region was discovered in this era and this led to development of high grade direct shipping grade hematite ores. Carpentaria Exploration (Capex) rediscovered the magnetite whilst undertaking multi-commodity exploration in the Broken Hill district during 2009. The magnetite grade was found to be low at around 16% Davis Tube mass recovery (DTR) but despite this, the project provides a positive business case as a result of the following key factors:• The mineralisation is particularly soft for crushing and grinding with a Bond Work Index of 6.3.• The mineralised rock fractures easily preferentially along grain boundaries.• The location is close to mining infrastructure and a skilled workforce in Broken Hill, 60km to the North East.• It is close to road and rail infrastructure for access to the resource.• The only contaminant in concentrate is silica.• The resource contains many billions of tonnes of magnetite mineralisation.The low Bond Work index is a key characteristic of the Hawsons iron ore and the use of autogenous milling and HPGR circuits is compared to other iron ores indicating why the plant energy requirement may be just as important as iron ore grades.

Aug 8, 2011

By S Goff

The Northern Sewerage Project (NSP) is a $650 M infrastructure project that will increase the capacity of the sewerage system for Melbourne’s growing northern suburbs while also helping to protect the Merri and Moonee Ponds creeks by significantly reducing the number of sewage overflows that can occur after heavy rainfall. The NSP consists of two stages: Stage 1 (NSP1) will be owned and operated by Melbourne Water Corporation, and Stage 2 (NSP2) will be owned by Yarra Valley Water and operated by Melbourne Water Corporation.Glass-fibre reinforced plastic (GRP) was used on both NSP stages, however, since Stage 1’s schedule for installation of GRP was slightly ahead of Stage 2’s, this paper will only focus on Stage 1’s use of GRP.NSP1 involves the construction of 7.9 km of new sewer tunnel ranging in diameter from 1.6 to 2.5 m, five main access shafts at depths of up to 65 m, and connections to the existing sewerage system including several access manholes. Construction began in 2007, and project completion is expected in 2012.The original design for NSP1 specified the use of high-density polyethylene (HDPE-) line precast concrete pipes as the final tunnel lining and HDPE-lined reinforced concrete for the access shafts and manholes. During construction, the rising cost of precast concrete pipes and the introduction of an additional GRP pipe supplier in the market justified a review of the tunnel final lining material. The contractor-proposed GRP pipe alternative was accepted for the final tunnel lining based on time and cost savings that were possible without compromising the design intent. After gaining experience with GRP through this design change, Melbourne Water Corporation reviewed and accepted GRP as the final lining for five smaller connection manholes. The use of GRP for the manholes was particularly inventive as the redesign made use of the approved tunnel GRP pipes as both a structural and corrosion-resistant lining.This paper discusses the use of GRP on NSP1; how the change in material, from concrete to GRP, affected the design philosophies assumed during detailed design; and how construction methods were modified to handle the less rigid GRP material. Details on the structural, hydraulic and durability considerations for the design are included, as are details about the time and cost savings and the quality and safety improvements that were achieved during construction.

Mar 8, 2011

By Neville Rockhouse

This paper examines the interrelationship of conducting full risk assessments in the context of the coal mining industry and under the framework of the Health's Safety in Employment Act 1992. In the context of Occupational Health's Safety, Risk Management is a holistic management process that can be used by individuals working in all organisations and from all industries. The Australian New Zealand Standard 4360: 2004 defines a Risk as being; The chance of something happening that will have an impact on objectives. This definition is followed by several notes that include: a risk is often specified in terms of an event or circumstance and the consequences that may flow from it, risk is measured in terms of a combination of the consequences of an event and their likelihood, and risk may have a positive or negative impact. For the purposes of this paper, the above definition will be adopted. This paper examines the newly expanded approach of the fully documented risk management process in the New Zealand coal mining industry. This is done in the context of the coal mining regulations but more importantly by using the framework of the Health & Safety in Employment Act 1992. This legislation under Section 6 requires all employers to, Take all Practicable Steps to prevent harm coming to employees while at work and to others who might be at or in the vicinity of a workplace. When the term 'all practicable steps' is studied, one can clearly see that such steps should be the same steps taken that a prudent and reasonable person would have taken given the same type of circumstance. Due to the fact that in New Zealand parliament made statutes is administered by a Government Department, means that their breaches will be heard before a judge in the District Court. Under the Westminster System of Justice, a basic dictum of that court in matters relating the occupational health and safety is that a breach needs to be satisfied to a specific standard. That standard is, 'Beyond a reasonable Doubt'. One of the primary benefits of adopting a proactive approach to risk management is that if the industry were to adopt similar approaches, then this mythology could be seen as an industry standard. As such, the approach carries the same status in a court of law, as that of an Approved Code of Practice.

Jan 1, 2007

WaihiÆs Cornish Pumphouse is located on the edge of town in a dynamic and changeable area where history affects the future. As in any successful project, ingenuity and team work have been significant factors in the planning and implementation of the buildingÆs relocation.   Work around the Pumphouse site commenced circa 1900 with preparation to sink the No 5 shaft. Construction of the pumphouse and the steam driven C pump was completed by 1904 with hints of what was to come evident in 1905 as the No5 Shaft collar had sunk 350mm in four years. By 1907 surface cracking developed over the Milking Cow cave area and in 1913 200 mm was cut off the main pumping rod as the ground was sinking at a rate of 25 mm per year.   In 1913 ground around No 6 shaft had subsided 600 mm.It was also the end of an era as steam gave way to hydroelectricity and electric pumps replaced the C Pump. C Pump was maintained as a backup from 1913 to 1929 and then finally scrapped. 25 years of underground caving operations removed approximately 400 000 cubic metres of ore leaving a 7 ha collapse crater that eventually became known as the mine lake.   On the edge of town a tension zone over the Royal Lode began to develop 50 m diameter chimney collapses as large scale blocks relaxed into unfilled stopes in the old Martha underground mine. After the 1999 collapse part of the main street was closed and after the 2001 collapse Hazard Zones were declared, more streets closed and areas evacuated and retired from residential use.   By 1984 the Pumphouse has approximately one degree of tilt and in 2002 tilt on the Pumphouse accelerated briefly and then settled down. Tilt accelerated again late in 2004 and a scoping study was initiated to define protection options for the pumphouse. The Martha Mining Licence requires Newmont to 'Take whatever precautions are necessary to protect the old Cornish Pumphouse adjacent to No5 shaft' and viable solutions needed to found.   Any work on the Pumphouse comes standard with a wide range of stakeholders, governing agencies and legal framework to consider. Land Information New Zealand (LINZ) is owner and administrator of the pumphouse.

Jan 1, 2006

By K Watters

API Management Pty Ltd (API) is currently developing the West Pilbara Iron Project (the ‘Project’). The Project is a substantial greenfi elds mining and infrastructure development proposed for the west Pilbara region of Western Australia. The Project will establish API as a new and independent supplier of direct shipped iron ore. API manages the Australian Premium Iron Joint Venture (APIJV) on behalf of joint venture participants Aquila Resources Ltd and American Metals and Coal International Inc. The APIJV was formed in February 2005 with the objective of developing a long-term iron ore export operation in the west Pilbara region.Development of Stage 1 comprises a 30 million tonne per annum (Mt/a) channel iron deposit (CID) operation scheduled to commence in the second half of 2014 subject to approvals. JORC compliant CID resources total nearly 700 million tonnes and the Stage 1 mining area comprises eight iron ore deposits located between 30 km and 85 km south of Pannawonica. Run-of-mine ore from the eight deposits is transported to a central processing facility for crushing, screening and blending into a sinter fines product, which API has named West Pilbara Fines or WPF. Construction of a 282 km main line heavy haulage railway from the Stage 1 mining area to the proposed greenfields multi-user port at Anketell Point near Wickham, is capable of accommodating large Capesize bulk carriers and providing export facilities for other third parties. Capital investment in the order of $A6 billion includes essential support infrastructure including power, water, accommodation, roads and an airport at the mine.A feasibility study for the development of the Stage 1 mine, rail and port infrastructure has been completed along with environmental surveys of the mine, rail and port areas with Public Environmental Reviews (PERs) for each submitted for public review by end 2010. Consultation and cooperation with various stakeholders of the Project areas, and early engagement with traditional owners of the respective areas has commenced. Various sampling and metallurgical characterisation programs combined with independent institute and steel mill based testing have confirmed the positive sintering characteristics of WPF ore, which is higher in alumina (3.37 per cent) than typical Pilbara ores. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

The Malvern Hills coal project is now in an advanced stage of development with the stripping of overburden from above former underground workings in which a 3 m seam of subbituminous C coal with very low ash and sulphur was previously mined. The main seam dips at 45¦ to the south-east, along with other adjacent potentially recoverable thinner seams, and the strike extent of past coal mining in the Malvern Hills approaches 10 km with most extraction by underground methods. Overburden and interburden is predominantly weak mudstone, with only very minor sandstone, whilst a 1 - 2 m thick veneer of Last Glaciation loess covers the area. The coal product from the present mine site will supply the local industrial market, with production planned to peak at about 20 000 tpa. Settling pond design has been based on several different approaches, including an estimate of likely inflows from the contributing catchment of about 5 ha under predicted storms having a ten year recurrence interval. A pond of about 1000 m2 in area has been constructed with its invert in mudstone bedrock, and soil slopes have been lined with lime-stabilised clayey loess silt incorporating a gravel armour layer. The pond outflow takes place via a 2 m high 1.8 m diameter concrete dewatering tower, with a skimmer arrangement to lower the pond by approximately 500 mm between storm events. The overflow water discharges to the main stream above a natural wetland, which will act as a secondary polishing pond, and this is to be enhanced in conjunction with the neighbouring forestry company. Discharge consents specify turbidity and pH as the controlling criteria, and both will be monitored at the settling pond discharge point as well as at the entry to the main stream. Investigations to date indicate that the pH of water exiting from previous underground workings is in the range 6.8 to 7.2, and that acidic drainage will not be an issue with this mine site. No dispersive clays have been identified in assessing the overburden and batter materials, although erosion during storm events is expected and all drains will ultimately be routed through the main settling pond to ensure adequate control of runoff-generated sediment. Reestablishment of vegetation on cut and fill batters remains a priority, and ongoing monitoring will ensure satisfactory long-term performance of the pond system.

Jan 1, 2003

This paper will examine the prospects for Queensland's non-fuel mineral industries as we approach the 21st century. The opportunity for growth is unprecedented. Exploitation of recent discoveries, proposals and developments in downstream processing are predicted to contribute to a doubling of the State's mineral exports to around $10 billion by the year 2000. In 1995 - 96 the value of Queensland's mineral production was $6 billion, comprising $1892 million metallic minerals, $127 million non-metallic minerals and $4 025 million total fuel minerals. For many years Queensland has been among the world's major producers of copper, silver, lead, zinc, bauxite and mineral sands. Recently Queensland has become an important producer of magnesia. Queensland's ability to compete results from its location close to rapidly developing Asian markets, the diversity of its major minerals and an increasing ability to add value to the resources base using competitively priced energy. Northwest Queensland is one of the richest base metal provinces on earth following the recent discovery of five world-class orebodies. Of these deposits, Osborne (copper-gold) has commenced production and Cannington (silver-lead-zinc) and Ernest Henry (copper-gold) are scheduled to be developed by 1997. Century Zinc Limited and the Queensland Government are negotiating with native title claimants on the development of Century (zinc-lead-silver). Expansion is in progress at the Mount Isa copper mine (renamed the Enterprise) and copper smelter and a high analysis fertiliser project may be developed based on Phosphate Hill. Korea Zinc Company Limited has reached agreement to construct and operate a 350 000 Mtpa zinc smelter/refinery near Townsville. There are future expansion prospects for the vertically integrated major industrial mineral operations based on Weipa bauxite and Kunwarara magnesite. Upgrading of the Boyne Island aluminium smelter will require a doubling of alumina consumption. Downstream processing options for Kunwarara magnesite are being investigated and are expected to lead to increases in production and the manufacture of a range of value-added products. At the Yabulu refinery near Townsville, nickel and cobalt production using imported ore is to be increased and a commercial cobalt plant is to be built. Additional opportunities for further processing and manufacturing are associated with proposed new mines at Ely (bauxite), Skardon River (kaolin) and Goondicum (ilmenite). Recently discovered resources of zeolite and perlite also offer exciting development possibilities. Other manufacturing opportunities such as glass and ceramics based on local and plentiful clay and silica sand could replace imports. Silica sand at Cape Flattery is currently exported and production is expected to double.

Jan 1, 1997

By D V. Bright

Oroya Mining LimitedÆs Mt Gibson Gold Project, 280 km north east of Perth, is one of Western AustraliaÆs more recent discoveries of a major gold resource. Modern gold mining commenced in 1986, on a shallow laterite reserve of 6.62 million tonnes averaging 1.50 g/t gold. By the end of 1998, mining had progressed from an initial three shallow laterite pits to a series of 14 open pits with maximum depth of 100 m, on three separate trends with a combined strike length of over 10 km. The Project has yielded 868 400 ounces of gold from 16.5 million tonnes of ore at an average recovered grade of 1.64 g/t gold, from near surface laterite, supergene and primary sulfide ores. This includes a 160 m deep underground decline operation which mined 120 000 tonnes at an average grade of 9.1 g/t gold and a four million tonne Dump Leach on a synthetic base which yielded 68 900 ounces. The Project was placed on Care and Maintenance in 1999 pending drilling to refresh reserves. Hosted by strongly tectonised and altered Archaean volcanic rocks within and adjacent to a major regional shear, primary gold mineralisation occurs as structurally emplaced sulfide and quartz lodes. On the main Gibson Trend, multiple zones of mineralisation occur within a zone up to 600 m in overall width. The overall footprint of known mineralisation exceeds 20 km2 and the potentially mineralised domain exceeds 100 km2. The current estimate of a combined resource of 9.4 million tonnes averaging 2.47 g/t gold (749 500 ounces) is derived from a database of 10 500 drill holes, of which only four per cent test below 100 m vertical depth. Ore envelopes which remain open at depth and major gaps in the drilling pattern beyond the currently defined resources promise straightforward potential to define additional resources. Oroya Mining Limited and its joint venture partner Barrick Australia are targeting a major gold mining operation from this potentially world-class mineralised system. Oroya has the exclusive right to produce up to 500 000 ounces and is working toward the completion of a feasibility study into a resumption of mining using the existing 1986-built 1 Mtpa processing plant. The joint venture is in the early stages of testing the depth and lateral potential of the Mt Gibson mineralised system. Mining options currently under review include progressive open pit extension and amalgamation leading to one or more large open pits, and underground operations. It is too early in the development of the Project to offer definitive economic models of potential large-scale mining operations.

Jan 1, 2003

By M Nagarajan, S Esen

This paper presents three case studies from three surface coalmines. The first case study is from a coalmine where a dragline operates in 60 m wide and 1 km long strips. Typical overburden height ranges from 30 m to 50 m. The base case blast was modelled using an advanced blasting model (Distinct Motion Code – DMC) to establish the baseline using the blasting parameters in use before optimisation. DMC was used to model the alternative blasting scenarios to obtain the following key objectives:the post-blast muck pile profile was required to have an optimum height of ~28 moptimise cast percentageachieve a well-fragmented muck pile for the draglinethe muck pile profile should be appropriate for the dragline entry into the strip.Achieving these objectives would optimise the dragline performance through reducing rehandle and improving advance along the strip. DMC modelling resulted in the following outcomes:the required muck pile profile could be achievedthe cast percentage increased from 21.1 to 25.1 – a four per cent increaserehandle volumes were reduced.Establishing a good quality assurance / quality control (QA/QC) process was essential to delivering a blast that could achieve these outcomes. The blast was fired successfully and the dragline completed the strip approximately two weeks ahead of the time taken for the previous strip.The second case study is from a coalmine where D11 dozers are used to move the blasted material to the spoil. An optimum profile was required for the dozers for this low-cost mining operation. To achieve this, an electronic blasting system (uni tronicTM 600) was introduced to optimise the muck pile profiles being delivered. The new muck pile profiles showed improved cast percentage from 10.6 per cent to 17.8 per cent. The changes in the muck pile centre of mass displacement improved dozer efficiency as a result of pushing material shorter distances to its final position. Dozer productivity (bcm/h) statistically did not change but coal was being exposed at a faster rate.The third case study summarises the results from a site where dozers are used to minimise the total mining cost. Traditionally, excavators had been used on-site with conventional blast designs. After firing the first cast shot, the blasted material was found reasonably well-fragmented. Although dozing productivity hasn’t been quantified on-site, operators were providing positive feedback (easier push) due to the reasonably good muck pile profile suiting to the dozers. This site also realised significant savings with the dozing as compared to their truck/shovel operation.CITATION:Esen, S and Nagarajan, M, 2015. Muck pile shaping for draglines and dozers at surface coalmines, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 409–416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J K. Claflin, S R. La Brooy, A M. Claflin

Rotary kilns have been in service in the gold industry to regenerate carbon for 65 years. At the time oxide ores with gold head grades of 8 to 10 g/t were being treated. Carbon could be regenerated adequately at 650°C and solution losses were less than 1%. Forty years ago, research indicated that heavily fouled carbon from flotation circuits had to be held at 750 to 850°C for ten to twenty minutes for full reactivation (Avraamides and La Brooy, 1987), gold head grades were typically 5 g/t and solution losses typically 0.02 ppm – still less than 1%. In 2017 it was determined (Claflin et al., 2017) that a residence time of less than 1 minute at 750°C can be adequate to reactivate carbon fouled with organics sufficiently to achieve 0.005 ppm solution losses in a flotation tailings leach plant.With the potential for discovery head grades to drop below 0.6 g/t, solution losses of 0.02 ppm represent over 3% loss. Tight operation of the whole carbon circuit is required to keep gold solution losses below 1% going forward.There are alternatives to a rotary carbon kiln, e.g. vertical kilns of which the Minfurn, Rintoul and Combustion Air kilns are examples. The alternative kilns can be heated using electrical heating elements, induction, and microwave. These kilns can operate successfully under the right conditions, however, they are almost exclusively for small carbon throughputs and are not suitable for the large carbon advance rates that are required to process low head grade ore deposits. Large throughput carbon kilns are are almost exclusively fossil fuel fired rotary kilns and the subject of this paper. In the view of the principal author, a fossil fuel fired vertical carbon kiln is preferred to a rotary kiln, however, it is not currently used in the industry.Thermal regeneration of activated carbon has a major impact on gold recovery in the carbon circuit. The carbon kiln and associated equipment constitute 3 to 5% of the capital cost for an oxide processing plant and up to 10% of the capital cost if flotation tails are leached. Despite the capital cost and impact on recovery, the carbon kiln is often poorly selected, operated and maintained.Six years ago Ausenco embarked on the Carbon Kiln Initiative to reduce solution gold losses. This body of knowledge has been published in a series of papers culminating in this paper on how to:1. Select a kiln appropriate for the flowsheet;2. Maintain the kiln to achieve design operation; and3. Operate the kiln to minimise costs and maximise reactivation.CITATION:Claflin, J K, La Brooy, S R and Claflin, A M, 2018. Carbon kiln selection, operation and maintenance, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 251–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D Judkins N OÆLoughlin

"Basin Minerals Limited commenced exploring for conventional strandline hosted mineral sands (rutile, ilmenite and zircon) deposits in the Murray Basin in April 1997. This has resulted in the discovery of a major mineral sands field in the Douglas Project area, located southwest of Horsham in the Wimmera Region of Western Victoria. After the successful completion of a pre-feasibility study on these deposits in September 2000, the Douglas Project has advanced to bankable final feasibility study. This study should be completed by mid-2002 to allow a decision to commence production in 2003 at an expected rate of in excess of 500 000 tonnes of combined mineral sands products per annum. The field comprises several mineralised strandlines. The main ones of economic interest are from west to east, the four strandlines, Acapulco, Bondi, Bondi East and Echo. These strandlines at August, 2000 contain total Inferred Resources of 443 million tonnes at 4.7 per cent HM at a one per cent HM cut-off; ie 20.8 million tonnes of heavy mineral concentrate which in turn contains 11.3 million tonnes of ilmenite and leucoxene, 1.3 million tonnes of rutile and 1.6 million tonnes of zircon. The heavy mineral concentrate is coarse-grained with mean diameter grain size of the strandline deposits ranging from 130 to 160 microns in size. Major controls on the formation of mineral sands deposits in the Murray Basin are discussed with reference to the main mineral sand bearing, strand plain domains; the Central Strand Plain, the New South Wales Strand Plain and the West Wimmera Strand Plain. The Douglas Project deposits on the West Wimmera Strand Plain domain are characterised by wide zones of mineralisation with high-grade cores (>10 per cent HM), low stripping ratios, and a valuable economic heavy mineral suite comprising 60 to 80 per cent of heavy mineral concentrate. Constituent mineralogy of the heavy mineral concentrate of the overall deposits is; ilmenite (40 to 58 per cent), leucoxene (five to seven per cent), rutile (four to ten per cent) and zircon (four to 14 per cent). The Douglas Project Area appears to be endowed with significantly enhanced levels of heavy minerals compared to other areas of the Murray Basin due to its unique palaeo-geographical position. Long shore drift to the south of the basin has caused large quantities of heavy mineral to be trapped against the palaeo-cliffs and headlands of a rugged palaeo-coastline which includes in a major embayment, the Grampian Mountains, the Black Range and the Glenelg Complex. To the east, major faulting and uplift has brought the fine-grained WIM offshore deposits close to the surface and has resulted in erosional stripping of mineralised strandline deposits. This mineralisation has been recycled and reconcentrated within the younger strandlines to the west within the adjacent Douglas Project Area. These strandlines are thought to be younger than other mineralised strandlines discovered to-date in the Murray Basin. The Project Area strandlines are described; ie their morphology, geology and patterns of mineral distribution. The mineralogy of each of the strandlines is distinctive and variations are noted along strike and section."

Jan 1, 2001

By L Richards, R L. Brathwaite, C Mazenga

Underground mining of gold-silver bearing quartz lodes was carried out in the great mines at Martha Hill, Waihi over 70 years from 1882 until 1952. Shafts and stopes reached a total depth of 600 m on 16 levels, with workings extending laterally some 1.6 km, and as new reefs were discovered the workings extended beneath parts of the township. Over their long life the mines produced 1217 tonnes of gold-silver bullion from processing 12.2 million tonnes of mined ore. In the early-1980s drilling proved large reserves of gold and silver ore remaining in stock-work zones between the previously mined lodes. This led to a new era of mining at Waihi with the opening of the Martha Hill open pit in 1988. A series of three sink holes have formed above unfilled stopes of the Royal lode. In 1999 a sudden collapse crater 40 m in diameter occurred near an occupied part of Waihi, placing in danger several houses and a busy street. This crater formed close to a similar crater that occurred in 1961. The 1999 collapse resulted in subsurface investigations and risk assessment studies being commissioned by the local Hauraki District Council. However, a further 50 m diameter collapse crater in December 2001 formed in a residential area, swallowing and wrecking an occupied house, fortunately without injuring its five occupants. Two other houses were perched on the crater rim. The 2001 collapse led to an acceleration of the work being carried out by the Institute of Geological and Nuclear Sciences Ltd. (GNS) to identify the extent of the old underground workings at Waihi. For the risk assessment detailed rock mechanics analyses were made to consider the stability of the underground mine stopes, in terms of the stope back, hangingwall, footwall and crown pillar failure mechanisms, as well as void migration. The collapse crater areas were analysed using using several methods, including analysis to simulate the probability of void migration from unfilled stopes to the surface using the @Risk program. The analyses show that in the cases of the actual collapse craters, the voids have a high probability of migrating to the surface, thus providing a method of testing the void migration modelling. Modelling analysis applied to the remaining stopes of the old underground mines show there are further areas where void migration from unfilled stopes has a high, medium and low probability of reaching the surface as a collapse crater. The locations of these probabilistic hazard zones were outlined using the @Risk modelling and deterministically by using the dimensions of the historical collapses applied along the length of the stopes. Consideration of the æincubation periodÆ (the time interval between the cessation of mining and the occurrence of collapse) and comparisons with mine subsidence histories overseas, indicates that further collapses are likely to occur over the next 50 years. Risk assessment estimates made using property values and occupancy levels within the three hazard zones, were compared with Societal and Individual Risk criteria. Results indicate that safety within the high and medium zones may be unacceptable.

Jan 1, 2003

By A Madera, R Watt

The Tampakan deposit is a strongly telescoped high-sulphidation-epithermal/ porphyry deposit pair which is hosted by a sequence of probable Pliocene age subaerial andesite flows. These host units lie on the western flank of a deeply dissected andesitic stratovolcano within the northernmost portion of the Sangihe Arc in southern Mindanao. The deposit was discovered by WMC geologists in 1992 and is currently undergoing resource evaluation. Preliminary resource estimations indicate a total inferred metal content of 12 million tonnes of copper metal and 16 million ounces of gold. Using a 0.2 per cent Cu cut-off grade, the deposit has a current mineral resource of approximately 2.5 billion tonnes with an estimated grade of 0.48 per cent copper. At a higher cut-off grade of 0.5 per cent Cu, the mineral resource is approximately 900 million tonnes with an estimated grade of 0.75 per cent copper. Mineralisation is open both to the west and at depth. The Tampakan district is centrally located with respect to a 100 km wide zone of left-lateral strike-slip deformation represented by the trans-Mindanao Cotabato Fault Zone. The district is transected by several WNW-striking wrench faults which represent strands of the regional Cotabato Fault Zone. High-sulphidation epithermal mineralisation within the Tampakan deposit is strongly controlled by NNE-trending faults which lie along a dilational orientation within the Pliocene stress field associated with the Cotabato strike-slip fault zone. The mineralisation is broadly hosted by a gently-dipping, tabular zone of partial to massive silicification which displays multi-phase brecciation, acid-leaching, related vuggy porosity and which is developed within a district-scale advanced-argillic and argillic lithocap exceeding 90 km 2 in area. High-sulphidation epithermal mineralisation is associated with a silica-pyrophyllite-dickite-alunite-diaspore¦sericite alteration assemblage which is transitional downward to sericite-chlorite alteration and relict potassic biotite-chlorite-magnetite-anhydrite alteration associated with pervasively developed but weakly mineralised porphyry quartz stockwork veins. The high-sulphidation mineralisation is dominated by disseminated, vein and vug-filling enargite-bornite-digenite-chalcocite-covellite ¦ molybdenite which has overprinted an earlier phase of porphyry copper stockwork veins associated with high-level porphyritic hornblende diorite stocks. The distribution of high-sulphidation alteration and mineralisation reflects strong stratigraphic and structural controls. The high-sulphidation mineralisation covers a surface area of approximately 1.6 km by 2.0 km and forms a tabular, flat-lying to gently-dipping body between 200 and 500 metres thick. It is intersected at RL-1200 m ASL (at surface) in the northern portion of the deposit and extends down to RL-600 m ASL at the southern end. The deposit has been diamond-drill tested to a depth of 400 - 500 metres where low-grade chalcopyrite-bornite-pyrite mineralisation is hosted by pervasive quartz stockwork veins. This deep-level mineralisation represents the outer portion of a porphyry Cu system hosted by both andesite flows and the uppermost portions of high-level hornblende diorite stocks. Deep drilling to test for higher tenor porphyry Cu mineralisation is planned.

Jan 1, 1999

The fluorspar deposits at Okorusu, Namibia are closely related to an alkaline igneous ring complex of late Cretaceous age (125¦7 Ma). The fluorite ores consist of relatively fine-grained purple replacement fluorite and subsequent coarser-grained purple and green vug-filling fluorite crystals. Homogenisation temperature measurements for 38 primary fluid inclusions shows that main stage purple to green fluorite crystals were deposited over a temperature range from 166¦C to 144¦C, and minor late yellow fluorite was deposited at lower temperatures from 132¦C to 128¦C. Homogenisation and freezing temperatures measured for 18 primary fluid inclusions shows that the fluorite-depositing fluids were less saline than Mississippi Valley-Type (MVT) ore fluids and overlap the lower temperature range of fluids that deposited epithermal ore deposits. Mining in three open pits (A, B and C) at Okorusu has gradually provided exposures which reveal that the fluorite orebodies have been emplaced primarily by the preferential replacement of carbonatites. Evidence for the replacement of carbonatite includes: replacement remnants of carbonatite within the fluorite ores; goethite pseudomorphs after the carbonatite minerals, pyroxene, pyrrhotite and magnetite, which are disseminated in the fluorite ores; andpartial replacement by fluorite of a large sill-like carbonatite body in the A pit. Electron microprobe analyses of minerals in unreplaced portions of the carbonatites show that their mineralogy consists of titaniferous magnetite, diopside pyroxene, apatite, biotite and calcite. Magnetite contains 6.97 per cent to 10.46 per cent TiO2, averages 8.44 per cent TiO2, and has an average V2O3 content of 0.35 per cent. At high magnifications under the scanning electron microscope (SEM), the magnetite shows abundant fine ulv÷spinel exsolution lamellae arranged in a cloth texture. Apatite contains moderately high fluorine contents that range from 3.21 to 5.0 per cent and average 4.2 per cent, and apatite crystals range in total rare earth oxides from 1.7 per cent to 2.61 per cent. Pyroxenes in the carbonatites are iron-rich diopside, and they contrast to pyroxenes in the fenites that are aegirine-augite. All of the microprobe analyses for mica crystals in the carbonatites give biotite compositions. Microscopic examination of fluorite concentrates from Okorusu provides mineralogical information important to the resolution of beneficiation problems. Fluorite ores that are related to carbonatites are typically accompanied by phosphorus benefication problems. The cause for the presence of phosphate in some of the Okorusu fluorite concentrates is a function of the presence of binary locked fluorite-apatite particles. The fluorite ores have also replaced marble locally in the A pit, especially along the A band in the B pit, and dominantly in the orebody proposed for the new C pit. Those ores are characterised by fine grain sizes, faint remnant bedding, lack of carbonatite mineral pseudomorphs and local presence of remnants of unreplaced marble. Concentrates derived from those fluorite ores are devoid of phosphorus, but commonly have elevated silica contents due the presence of free quartz. Carbonatite and marble were preferentially replaced by fluorite because the calcite was readily soluble in the presence of the fluorite-depositing fluids and the dissolution of calcite provided calcium for the formation of fluorite. 

Jan 1, 2008

By J M. F Clout

The low-grade clay-rich -1.0 mm fraction of fine iron ores have often proved difficult to upgrade and capital intensive to process when using traditional wet beneficiation technology including single or two stage hydrocyclone desliming, wet high intensity magnetic separation (WHIMS), spirals and final dewatering using fine screens. Very fine (<0.010 mm) clay-rich slimes simply follow the water split to the hydrocyclone underflow where it often impedes the subsequent processing performance of any downstream spirals and can result in troublesome direct dewatering of hydrocyclone underflow. The -1.0 mm fraction in goethitic iron ores is typically considered as waste. A new two-stage wet gravity separation flow sheet, referred to as the ædesandÆ process, has been designed to overcome these issues for the upgrading of low-grade clay-rich goethitic or hematite-quartz fine iron ores. The desand process is designed to treat the -1.0 mm range from -8.0 mm natural fines, to recover a -1.0 +0.038 mm higher-grade fraction by rejecting to tailings any low-grade clay-rich ultrafines and low density sand-size fine chert/quartz gangue and shale.The desand process consists of wet screens with a nominal 0.7-1.0 mm cut point which direct the undersize to hydrocyclones. The hydrocyclone underflow is then fed to upcurrent classifiers where the classifier middlings is sent to spirals and classifier and spirals concentrates are then dewatered using vacuum belt filters or fine screens. The three product upcurrent classifier is employed to further deslime the hydrocyclone underflow, producing firstly a coarse final concentrate, and then a deslimed middlings for feeding to spirals as well as a 0.100 mm clay and fine quartz or banded iron formation (BIF) sand in final overflow for feeding to the residue thickener. The upcurrent classifier middlings provides the spirals with a significantly cleaner feed material than traditional methods, with the end result that the spirals do not silt up with slimes and therefore can continue to run at their optimum. The upcurrent classifier and spirals form a complimentary pair, with the upcurrent classifier better able to send coarser, acceptable grade particles to concentrate and fine slimes to tailings whilst allowing the spiral to better reject coarser, subgrade low specific gravity particles. Test results for the Mayoko-Moussondji iron project, Republic of Congo, using upcurrent classifier-Wilfley Table (simulating spirals) gave acceptable mass recovery from run-of-mine (ROM) and Fe recovery from hydrocyclone underflow for HEMCOL (6.2 per cent mass recovery from ROM/43.1 per cent Fe recovery) and HEMBIF2 (5.1 per cent mass recovery from ROM/22.3 per cent Fe recovery) mineralisation types. The desand process also enables improved dewatering of -1.0 +0.038 mm product from a clay-rich plant feed.A number of new wet plants in the Pilbara use the desand flow sheet including FMGÆs Cloudbreak and their two Christmas Creek plants. Many potential new applications are being explored, with new iron ore plants in India as well as those being proposed for West Africa. Operational experience has highlighted the importance of providing clean process water to the upcurrent classifiers as well as ongoing design improvements including increased wear life, reduced maintenance and enabling a more steady feed rate to spirals.CITATION:Clout, J M F, 2013. Beneficiation of fine iron ores using the desand process, in Proceedings Iron Ore 2013 , pp 337-348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

In order to understand the technique, basic theoretical principles of radiation emission and in- strumentation theory are reviewed. Methods of surveying, reduction of data and interpretation are outlined. Other applications of the technique (e.g. in airborne geological mapping), as well as its specific use in uranium exploration, are discussed. By means of case history-type examples the successful applicant of gamma-ray spectrometry, as a tool in Australian mineral search, is demonstrated.

Jan 1, 1969

By Misra A

After review of the status of research on optirnisation of retreat longwall faces it is argued that an acceptable optimisation model must be based upon realistic cost data that take into account not only the face costs, but the total panel costs. These include the cost of development, face cost, removal and installation cost. The determined optimum length of a retreat longwall face is based upon a realistic model and actual costs.Parameters that influence the optimum face length have been varied over wide limits to allow determination of the sensitivity of the model and the effect of the parameters on the optimum face length. It is concluded that for medium production rates and medium system availability, the optimum face length of a retreat longwall face under Australian conditions lies between 180 and 220 metres.

Jan 1, 1995

By Neill A, O&apos

The City of Kalgoorlie/Boulder is situated approximately 600 kilometres to the east of Perth (Fig. 1), and is the major regional centre of the Eastern Goldfields, supporting a population of approximately 25,000. The formation of Kalgoorlie Consolidated Gold Mines in 1989 brought the existing operat- ing entities adjacent to the city under common ownership and management. The Joint Venturers forming the management company are Homestake Gold of Australia and Gold Mines of Kalgoorlie (a Normandy/Poseidon com- pany). This traditional underground mining centre has been worked since 1893, yielding 40.8 million ounces of gold from ore with an average head grade of 10 grams per tonne. Historically the heart of the operation has been the famous Golden Mile located on the Eastern perimeter of the city, in the area known as Fimiston. The other significant operations that form KCGM are the Mt Percy Open Pit and the Mt Charlotte Underground Operation. KCGM's current production is 520,000 ounces per year, with the com- bined Fimiston operations (open cut and underground) contributing 400,000 ounces. The current expansion will increase production levels by a further 150,000 ounces. Traditionally 98 per cent of gold has been sourced from underground areas, however the recent upsurge of open cut operations is rapidly overturning this historical relationship.

Jan 1, 1991

By Munive L

As a result of commissioning No.5 B F, 2670m3 inner volume, in March 1972, the largest B F in Australia; new expertise in maintenance, furnace operating practices and design have been obtained. This experience has also been extended to the other furnaces. A series of operating problems were con- fronted; all parts of the furnace, including the hearth side walls and bottom,were adversely affected. In December 1977, serious hearth wall wear was detected at No.5 B F, and a potential hearth breakout was averted. Hearth wear in No.4 B F was discovered in March 1979, and emer- gency underhearth cooling was installed to reverse an extremely advanced hearth bottom erosion. Hearth behaviour of No.5 B F oampaign 1972-1978 and`No.4 B F campaign commencing 1972, has been studied and discussions on the causes, effects and measures undertaken to protect the hearths are presented in this paper.

Jan 1, 1981

Coal washing practice can be improved not only by critical examination of the plant being operated but also by studying plants operated in other areas. The developments at the Australian Iron & Steel Pty. Ltd. plants are discussed in relation to experiences there as well as developments which have taken place in Queensland in recent years. Early A.I.S. problems involved small coal cleaning in heavy medium cyclones and flotation. A proposed future plant flowsheet for A.I.S. is considered in the light of these experiences. Reference is made to plants operated by the Thiess, Peabody, Mitsui Coal Company Pty. Ltd. at Moura and the Utah Development Company's plants at Blackwater and Goonyella in the development of coal washing prac- tice in Australia.

Jan 1, 1975