Search Documents

By G E. Smith, G N. Lye

Wall control blasting practices are necessary to reduce the impact of blasting on mine faces but can also have a significant negative impact on mine productivity and operating costs. The conventional practice in deep open pit mines is to use so-called trim blasts adjacent to pit walls. To provide burden relief these trim blasts have fewer rows than full production blasts and are fired to a cleared free-face; hence they are termed æunchokedÆ. This practice leads to scheduling constraints on the pit operations and can cause ore dilution due to excessive muckpile movement. The use of such trim blasts stems from the perception that increased wall damage results from æchokedÆ blasts. These concerns are based on the unproven assumptions that blast vibration levels and explosive gas penetration increase with increased blast burden and face confinement. This paper describes work undertaken as part of a major investigation into wall control blasting at the KCGM Fimiston Mine, Kalgoorlie, Western Australia. It details a study to assess damage effects due to blast burden. Borehole air pressure measurements and borehole video camera inspections were done behind a series of single blastholes drilled with varying burden distances, as well as behind a dedicated trim blast and a full production blast. It was found that the measured damage effects, including visible rock cracking, dilation, and the limited extent of gas penetration behind the blastholes, did not vary significantly with burden or blast type for the cases tested. This result was in complete agreement with detailed vibration measurements conducted by Blair and Armstrong (2001) during the study, which found that vibration was independent of blast burden. As a result of these investigations, changes to the blasting practices at the mine were implemented. Dedicated trim blasts and free-face blasting have been replaced by modified production blasts and the practice of æchokingÆ blasts has been introduced. This has resulted in a significant improvement in productivity and cost savings without compromising pit wall integrity.

Jan 1, 2001

By K Li, C Zhang, i, J Oh, S Saydam, H L. Ram

Rock surface roughness plays an important role in excavation engineering projects and applications related to surface support structures, such as shotcrete and thin-sprayed liner (TSL). The morphology of the substrate affects the mechanical behaviour at the interface significantly. Therefore, it is necessary to quantify the roughness to investigate the relationship between roughness and mechanical properties. The joint roughness coefficient (JRC) proposed by Barton and Choubey (1977) is widely used in practice. It initially estimated the roughness by comparing it to 10 standard profiles visually. However, this method has lots of limitations, it is not only subjective but also a two-dimensional parameter with a small lab scale (Beer, 2002). The subsequent research on JRC, from visual comparison with Barton’s standard profiles to measuring the roughness with a profilometer (Weissbach, 1978; Alameda-Hernández et al, 2014). Then, 2D profiles or 3D surfaces by different technologies with higher resolution and accuracy, such as 3D laser or optical scanners (Fardin, 2004; Jiang, 2020, 2021). These 3D scanners are expensive and only suitable for laboratory scales. LiDAR scanners (Lato, 2009; Aubertin, 2022) have been applied in industrial size, but it is difficult to achieve a millimetre-level accuracy, which is mostly used to detect the thickness of shotcrete in practice. Thus, finding a cost-effective surface roughness measurement method with high accuracy is necessary. Photogrammetry is another method to digitalise the roughness of the surface. Similar to 3D scanners, photogrammetry also generates the point cloud of the objective surface and then reconstructs the 3D model of the objects. 3D reconstruction technology is a trendy technology in recent years. The structure from motion (SfM) algorithm (Westoby, 2012) to rebuild the 3D model with a flexible workflow, aligning photos, building dense point cloud, mesh and texture, which has been proved that can rebuild an accurate model in variable fields.

Nov 29, 2022

By A Taheri, G D. Nguyen, M Karakus, S Akdag

During underground mining operations, rock masses are highly subjected to dynamic disturbance caused by blasting, mechanical drilling and earthquakes resulting in strain burst, slabbing and spalling. The dynamic fracture is a significant manifestation of rock failure in deep underground engineering, and it is of great importance to assess the dynamic fracture behaviour of the rock mass under elevated temperature conditions. The correlation between temperature – and loading rate-dependent dynamic fracture mechanism of strain burst is yet to be established. A good understanding of the dynamic fracture behaviour of brittle rock subjected to high-temperature under dynamic loading is required for the prediction of the damage extent during strain burst, and proper design as well as control of the underground rock structures. In this study, dynamic mode I fracture toughness tests are carried out on cracked chevron notched semicircular (CCNSCB) granite specimens to reveal the dynamic fracture characteristics of the brittle rock. For this purpose, a Split Hopkinson Pressure Bar (SHPB) apparatus is utilised to conduct the dynamic tests with various striker velocities on thermally degraded granite. The dynamic mechanical behaviour of granite after high-temperature treatment is examined and discussed. The dynamic fracture toughness is determined and compared for the specimens exposed to different temperatures at various dynamic impacts. The fracturing processes are recorded by a high-speed camera (HSC), and the crack propagation speeds are estimated by HSC image analysis. In addition, the dynamic fracture process and the coupled effects of temperature and loading rate on the dynamic fracture modes are identified by HSC image analysis. Energy partition characteristics in dynamic fracture of granite are quantitatively investigated.

Nov 29, 2022

By T GRAHAM-TAYLOR

A trend towards mining more complex and economically marginal orebodies, often combined with increasingly tight product specifications, increases the number of variables which need to be considered in production scheduling. Linear programming incorporating integer constraints can be used to create production schedules which are practical as well as mathematically optimum. Factors which can be taken into account include variability in product stockpiles, targets for head or product grades, production of different material types, production from different areas, production targets for loaders, and dependencies between mining blocks. For each schedule an appropriate objective for optimisation must be chosen. Examples of objectives are: to minimise or maximise grade variation; to minimise waste movement; and to minimise movement by front end loaders. A staged approach to the implementation of computer systems based on linear programming optimisation is Proposed.

Jan 1, 1992

By W van der Westhuizen

Mining professionals recognise the need and application for reconciliation and value tracking. It is necessary however to examine our current reality, and evaluate the following. Do our reconciliations really balance correctly, and are we able to track value effectively throughout processes? If we are honest, in most operations the answer is a resounding no. This means that we are surrounded by fluctuation and deviations that we do not account for and do not understand. This is astounding, because given our level of scientific knowledge and the technological tools at our disposal we should have a good understanding of our environments and be able to manage them effectively. How do we manage effectively if we are surrounded by so much uncertainty? The purpose of this paper is to describe, at high level, the principles of reconciliation and value tracking, to highlight some areas where deviations are introduced into the mining process, and to propose a different approach to the apparent reconciliation and value tracking conundrum. The paper also poses several questions that need to be critically addressed at most operations. Instead of making the same mistakes each month in reconciliations, mining professionals need to acknowledge two facts. Firstly there will be uncertainty that we need to accept, since all our estimates are based on sampling, an orebody is not homogeneous and peopleÆs behaviour will influence the process, etc. Variability will always exist and lead to uncertainty. What is the current approach in the reconciliation process when a deviation occurs and how do we use reconciliation and value tracking to manage and improve our business? The second fact is that we need to stop using reconciliation and value tracking to only measure and report. We need to adopt a new approach to manage mining throughput, where reconciliation and value tracking are enablers to the success of the business. In most mining operations, significant effort goes into planning and measurement for the purposes of reconciliation and value tracking. The importance of accurate and effective reconciliation and value tracking should be to ensure the maximum utilisation of the resource, maximising throughput and enabling the business to deliver a product to its client, of the correct quality and in a timely manner.

Jan 1, 2002

By Cerutty L

To those who have been engaged in the construction of mining and metallurgical plants during the war and post-war periods, it is quite unnecessary to point out the large increases and violent fluctuations in prices of basic commodities and the steady and persistent rise in labour costs. It may, however, be of interest to present these facts in graphic form, and survey the relative heights of the various maxima and the lead and lag of individual waves. Since Descartes demonstrated for us moderns the analogy between geometric form and algebraic statements, the two-dimensional graph has found widespread application. Mathematicians have developed for our information, if not for our confusion, the triangular diagram and the solid three-dimensional figures, which have proved so useful, at least in the hands of the metallurgists at Port Pirie. The model (Plate 1.) which is exhibited here does not pretend however, to indicate the connection between any three inter-related variables, and it is not proposed to burden members with any abstruse mathematical expression for the irregular surface of the blocks. While time is an ordinate common to all sections of the model, each illustrates separately the variation in cost of some particular quantity between the years 1914 and 1922. It is an easy matter to record such individual variations, but it would be an impossible task to state any equation describing accurately the dependence ot the prices, say, of hardwood or of galvanized iron upon that of labour at any particular point of time. The cost of living curve, which has attained such prominence, if not notoriety, in the last few years, is the result of an attempt to show the mass-effect of the components. It is the difficulty found in "assigning the correct weight to the separate items which makes the aggregate curve somewhat misleading at times.Turning to the model, it will be noticed that each section consists of half a dozen pegs.. The first in each row,that coloured red, represents the cost of some particular quantity, such as bricks, timber or coal, at Broken Hill in 1914. The next peg, that coloured blue, represents proportionately prices for that quantity in Hobart during...

Jan 1, 1922

By R Millar

A frequent challenge in mine water management and mine design is estimation of precipitation and extreme rainfall given a short record of site meteorological data. For remote mine projects, typically only a few years of rainfall data are available, which is far too short for estimation of design rainfall event, such as the 1-in-100 year storm. A frequency-paired approach is presented for comparing daily precipitation records from a mine site with a long-term regional station and provides the basis to transpose the long-term record to the mine site. This allows a long-term synthetic precipitation record to be developed for the mine site that can be used to undertake site water balance studies, determine pond storage requirements, assess water supply options and address other surface water management issues. Conventional approaches are based on chronologically-paired data and when applied to daily data generally yield poor correlations between stations. In the frequency-pairing approach, statistical distributions (two-parameter gamma distribution) are fit to daily data from two stations and used to calculate daily and extreme precipitation values for the short-term site (which is typically a mine or other project site). The method is demonstrated using data from two meteorological stations located along the south coast of British Columbia, Canada. Use of a fitted two-parameter gamma distribution (or other distribution) provides a sound theoretical approach to comparing precipitation data from two sites and the basis for transposing a long-term record to generate synthetic precipitation series and extreme rainfall values at mine sites.CITATION:Millar, R, 2013. A statistical approach for deriving project design rainfall, in Proceedings Water in Mining 2013 , pp 273-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

Open pit mining at Bingham Canyon commenced in 1904 and about two billion tonnes of ore have been extracted since then. There remain just under one billion tonnes of ore in the pit and this will be mined by 2015. Because the porphyry system extends below the ultimate pit limits, Kennecott Utah Copper Corporation initiated a study in 1997 to determine the viability of underground mining. The study was initiated at that time because the results were to be used to compare the economics of a further pit expansion to that of an underground mine. If a pit expansion was viable then overburden removal would have to start in the near future. This paper is a summary of the work that was carried out for the underground study. Block cave mining was determined to be the most appropriate method to mine the deposit. Two block cave areas have been planned with a total production rate of 72 500 tpd. Additional sources of ore will come from skarn orebodies that are associated with the porphyry deposit. The geology of the deposits is described together with the geotechnical techniques that were used to characterise the rock in the absence of more detailed data that are normally available. A general description of the mine plan is given along with the reasons for selecting the particular methodology used. The study was completed at the end of 1998 and demonstrated the viability of underground mining at Bingham Canyon. Funds have been approved for further drilling and technical studies, which will lead up to a feasibility study in 2004/5.

Jan 1, 2000

The knowledge in the field has been reviewed by literature studies, and using experience from personal research in sublevel caving. There is a lot of material regarding gravity flow of fine grained materials in bins, but the theory of flow for these materials are normally not applicable for coarse blasted rock. This study was therefore concentrated towards coarse rock fragments created after blasting in orebodies. The goal for this study was to make a report of known knowledge, and identify what we have to learn more about. The Bergmark-Roos theory, which was a paradigm shift in the science of gravity flow, is today the best mathematical theory for calculation of the drawbody for a homogenous material or when we wish to simulate the mean drawbody for a large number of draws. The Bergmark-Roos theory must however be improved, so it can take into account the flow pipe effect. When this is done it will be possible to construct a 3D computer model for calculation of ore extraction versus amount of loaded ore and waste. It is also necessary to find the 3D shape of the flow cone to be able to calculate the 3D ore rest that normally develops on footwalls. Calculations should be done for the draw on several sublevels including determination of the ore losses and temporary ore rests. First when this computer model is developed optimisation of ore recovery and waste rock dilution can start for a given orebody. The author points out the importance for international co-operation and standardisation of methods for determination of material properties. More field tests and model blasting tests should also be done. When enough knowledge is gathered, a handbook of the optimisation of sublevel and block caving should be written.

Jan 1, 2000

By D Smith

The Broken Hill deposit is located in Australia in the far western region of New South Wales. The deposit was found in 1883 and has been mined continuously since its discovery. It is considered the largest lead, zinc, silver deposit that has been discovered in the world and originally contained around 340 Mt of ore at a grade of around 12 per cent lead, ten per cent zinc and 150 g/t silver. The material remaining in the deposit represents only a fraction (perhaps ten per cent) of the original resource. Several of the world’s largest mining companies can trace their origins to the Broken Hill Field. The remaining resources on the CML7 consist of two large lower grade resource lodes that have not been subject to mining, some scattered areas of zinc lode material and the pillars and remnants of the main lead lodes.The deposit occurs in metamorphic rocks of the Broken Hill Group a division of the Willyama Super Group contained within the Curnamona Craton. The Broken Hill Group rocks have undergone multiple phases of deformation. Metamorphism is granulite grade with major shears cutting through the deposit having been retrogressed to mica schists. The deposit lies in an antiform associated with the second phase of deformation.The resultant proposed mine is situated on Consolidated Mining Lease 7 (CML 7) which occupies a strike length of 3.6 km in the central part of the 7.8 km long footprint of the orebody. Underground mining on CML7 ceased in 1975 with surface mining of silver chlorides in the weathered zone continuing until 1991. CBH Resources has been continually working to define and evaluate the remaining resource since 2002. This work has included four surface drilling programs, two underground drilling programs, an exploration decline, enormous amounts of compilation of historical data and detailed three- dimensional (3D) modelling of historical mining and the resource lodes. It is currently planned to commence production at the Rasp Mine in late 2011. The operations will produce from previously unmined lodes and from remnants and pillars.This paper primarily aims to encapsulate the processes involved from information acquisition through to resource estimation and also to highlight some of the challenges encountered and the specific techniques and practices used to overcome them. Many of the experiences at Broken Hill are applicable to all brown field sites.

Aug 22, 2011

Remote sensing techniques can be used to map joint sets in a rock mass for the estimation of in situ block size distribution and improved optimisation of blasting. This paper reviews remote sensing using photogrammetry and laser mapping for mapping rock masses and presents elements of the analyses applied to data acquired with these mapping technologies. These techniques enable a user to map areas of hundreds of square metres rapidly with high precision. Using this data computer programs such as Sirojoint can provide estimates of joint position and orientation with orientation measurement accuracies better than one degree. The paper describes the use of remote mapping and provides potential users with a description of some of the advantages and limitations of the mapping techniques and the data they produce. Mapping of lithology and structure of rock masses is an important task required in many areas of mining and construction. It is a complex task routinely performed using established techniques developed to provide consistent results under a wide range of conditions. The techniques for data acquisition and analysis described in this paper enable more accurate mapping to be performed rapidly and enable mapping of inaccessible sections of a rock mass. These techniques will provide geologists and geotechnical engineers with more detailed, accurate data than previously available.

Jan 1, 2001

By D J. Bradshaw, E M. Wightman, B Newcombe

Flash flotation plays an integral role in many of the gold and sulfide mineral concentrators around the world, and yet despite this widespread use, very little information on this unit process is available in the published literature. For operations to maximise the performance of their flash flotation circuits, understanding how these cells operate, the nature of the particles they target and how to predict whether a flash flotation cell should be used on a specific ore type is of vital importance. This paper provides a summary of the key findings of a large flash flotation research project based in the operating environment of a refractory gold concentrator. The influence of key flotation performance criteria including gas dispersion, residence time and particle segregation within the cell will be discussed and recommendations for process improvements will be made throughout. The nature of the particles within the flash cell will be examined, as will the impact on the type of particles that are passed to downstream processes when the flash flotation cell is taken off-line. The development of a laboratory method to determine whether an ore is suitable to undergo the flash flotation process is also presented for its potential to aid in flow sheet development and optimisation for new ores.CITATION:Newcombe, B, Bradshaw, D J and Wightman, E M, 2012. Into the belly of the flash à Insights into the mechanisms at work within a flash flotation cell, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 163-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By C R. Stanley, D Lawie

The measurement of error in assays collected as part of a mineral exploration program or mining operation, including errors introduced during sampling, sample preparation, or geochemical analysis, historically has been undertaken in a variety of ways. Different parameters have been used to describe the magnitude of relative error and each of these parameters is related to the standard measure of relative error, the coefficient of variation. Calculation of the coefficient of variation can be undertaken in a variety of ways; however, only one produces unbiased estimates of measurement error: the root mean square coefficient of variation calculated from the individual coefficients of variation. CITATION:Lawie, D and Stanley, C R, 2012. Average relative error in geochemical determinations - Clarification, calculation and a plea for consistency, in Proceedings Sampling 2012 , pp 181-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By S-C Shim, H-R Lee, Y Kang, H Shin

Since iron oxide and silicon oxide are major gangue components in various types of ore, FeO-SiO2 base slag, ie fayalite slag, has been often encountered in pyrometallurgical processes of non-ferrous metals. During most matte production processes such as the smelting of Cu, Pb, and Ni, the FeOSiO2 based slag is inevitably formed and plays an important role in refining crude metal as well as engineering aspects. Recently, similar pyrometallurgical approaches have been attempted in the recovery of valuable metals (Ni, Co, Cr) from wasted secondary batteries. Thus, the viscosity of the FeO-SiO2 based slag has great significance in properly controlling smelting processes. However, when molten metal or matte does not coexist with the slag during the measurement, there has been a serious difficulty in maintaining Fe valance and consequently, the slag composition. In the present research, the viscosity of molten FeO-SiO2 slag was measured in 1573~1673 K using a rotational viscometer. In order to keep the state of iron oxides, the oxygen partial pressure was controlled using CO/CO2 gas mixture. The optimised ratio of CO/CO2 could be calculated using Fe/Fe2+ and Fe2+/Fe3+ equilibria at each temperature. The composition of the slag, particularly Fe valance, after the measurement was analysed with the aid of an inductively coupled plasma – optical emission spectroscopy (ICP-OES) and an automatic potentiometric titrator. The measurement showed that the FeO-SiO2 slag has considerably low viscosity values in the molten state, and it sharply increases as the temperature decreases. In spite of the careful oxygen partial pressure control, a part of Fe2+ was found to be oxidised to Fe3+, with a maximal case reaching about 20 per cent. The increase in viscosity of FeO-SiO2 at low temperatures can be attributed to the composition change due to an unavoidable Fe2+ oxidation. In addition, the relationship between the change in the viscosity and the liquidus temperature of FeO-SiO2 based slag was discussed to understand the composition dependence of viscosity.

Jun 19, 2024

The key to the successful debt funding of a new mining project, whether in economically established or developing nations, is the submission of a comprehensive feasibility study. The feasibility study forms the basis from which the resource banker can construct financial models which govern the amount of available funds, the conditions which control the supply of such funds and the time period over which the loan may be repaid. The bank will wish to ensure that the feasibility study is the best representation and confirmation of reality possible because this model is the basis of the loan security package. Thus the study will be vigorously interrogated by independent experts in all its elements including the ore reserve, mineability, metallurgy, operating and capital cost profile, environmental factors and management.

Jan 1, 1995

A variety of algorithms and methods are being used by the mining industry today to map mineral resource for reserve estimation. The traditional methods including Polygonal, Sectional and Inverse Distance methods are relatively easy to understand and implement. They have served industry well for several decades and should continue to do so for the large bulk mineable deposits with very regular geometries with relatively small variation in grade.

Jan 1, 1992

By B P. Micke

Central Norseman Gold Corporation was established in 1935 and has been mining on the Norseman field in Western Australia since then. It is Australia’s longest continuously operating gold mining operation at nearly 80 years, although it has had its periodic challenges in the intervening years.Over the last 40 years, a series of open pit mines around the Dundas Goldfield have supplied lower cost mill feed to the Phoenix Mill at Norseman from time to time but this has largely come to an end for the foreseeable future. Now that underground ore sources are once again the principal mill feed, there are several challenges to be met for an ongoing profitable operation.During the last 20 years, there have been three different owners and this has affected the manner in which the operations were managed quite significantly. These differing approaches are contrasted and examined in some detail from both the operational and financial aspects.Planning of a downsized operation to ensure sustainable profitability in the future in a mining environment where there has rarely been more than two to four years of reserves ahead of the mill for planning purposes has been a significant challenge. Several of the options examined are described, including alternatives for future mine development.CITATION:Micke, B P, 2014. Managing the margin at Norseman, Western Australia – a case study, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 119–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By R Stead

So many ceramics look the same, but are they?In the past 20 years, there have been significant changes in the materials available, as well as changes to the supply chain, for ceramics used in wear applications in the hard rock mining industry. The biggest change in supply has been from the Chinese market, with many suppliers promoting their products as æstate of the artÆ. Some of them are state of the art, but are they all? There will be some concluding remarks in this respect.There are still some outstanding new developments coming from the more traditional suppliers and these should not be ignored. However, as an end user, how can one be sure that the product received meets the technical specifications of that material?This paper will address some of the questions on how to differentiate between different materials by giving a technical overview of the current (but not exclusive) range of popular ceramics, plus incorporating how these ceramics are used in process plant products by presenting case studies. The presentation will include technical data coupled with micrographs of various ceramics to illustrate just why they are different.It will also be shown that by careful selection of the wear material, it is possible to gain significant benefit when using superior materials in an ore processing plant. The impact of cost of the products, life, process efficiency, and reduced maintenance costs will be considered using cyclone components as an example.The properties (including the microstructures) of the various ceramics will be compared to the application in order to get some understanding of what is considered good or bad.Misra and Finnie (1982) summarised their paper, æA review of Abrasive Wear of MetalsÆ by saying:à it is difficult to give guidelines for selecting materials for abrasive wear resistance. Each application is a different one, and a design engineer has to take into account various other factors such as impact, fatigue and corrosion which are often coupled with abrasive wear. The same applies to ceramics.CITATION:Stead, R, 2013. Applications of ceramic wear materials in the gold industry, in Proceedings World Gold 2013, pp 325-330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By C J. R Hart, J K. Mortensen

The distribution of mineral deposits within northwestern North America (Alaska, Yukon, and northern British Columbia) allows for an in-depth examination of the metallogenic patterns of a growing continental margin. A more complete understanding of the tectonic evolution of this part of the Pacific Rim, achieved over the last 15 to 20 years, now allows for the placement of ore systems into a well-defined plate tectonic framework. Ore deposits older than about 185 Ma represent hydrothermal systems that were active in the platform/shelf environment of ancestral North AmericaÆs miogeocline or hydrothermal systems developed in oceanic arcs and continental fragments more distal to the craton. These include important SEDEX, VMS, and pre-accretionary porphyry deposits. In contrast, most mineral deposits younger than about 185 Ma were formed within the growing Cordilleran orogen, as terranes were accreted to the continental margin during interactions between the North America and Pacific/Farallon/Kula plates. Such syn- to post-accretionary mineralised systems include many large lode gold and porphyry/skarn systems.

Jan 1, 1999

By Taylor R. K A, Berglin C. I K

The manganese ore deposits at Groote Eylandt are quite variable both in regard to grade and physical cond- ition. In order to treat a wider range of these ores and to increase production a new primary-crusher and' concentrator complex costing $8 million has been installed and commissioned to treat ore at the rate of 12,000 tonnes per day. The initial testwork carried out to determine the method of the ore treatment required, and on which the design of the concentrator was based, is detailed. The flowsheet and equipment used is discussed together with the operation of the plant. The production achieved and product qualities obtained are given.

Jan 1, 1973