Search Documents

By Rynn J. M W, Paynter A

Recent studies by the authors have concerned themselves with assessing the earthquake risk to north-eastern Australia, based on available historical earthquake data for the area. There have been several significant earthquakes (Richter local magnitudes of the order of 6) concentrated in the Wide Bay - Burnett region in central eastern Queensland, although none of these has occurred close to a significant centre of population or development. Using derived average acceleration attenuation relations and world-wide data on earthquake-induced damage as a basis, conditions under which earthquake-induced liquefaction may occur have been investigated and presented in graphical form. Historical earthquake data for north-eastern Australia have been overlain on this graphical presentation and it has been demonstrated that the Wide Bay - Burnett region, in particular, may in the past have been on the verge of earthquake-induced liquefaction, where ground conditions are susceptible. When this is viewed in the context of the rapid growth in population and development in this area over recent years, the risk can no longer be ignored with impunity.

Jan 1, 1990

By Borsaru M, Wylie AW

A neutron irradiation technique has been developed which is suitable for the determinat- ion of the iron and aluminium content of iron ore fines (-6 mm particle size) on a moving rubber conveyor belt. The determination of iron entails measure- ment with a NaI(Tl) gamma ray detector of the characteristic prompt gamma rays (7.64 MeV) due to thermal neutron capture in iron, while the determination of aluminium is based on thermal neutron activation analysis. For the latter a second detector must be placed down- stream to monitor the 1.78 MeV gamma radiation emitted after activation of aluminium. Although conveyor speed has no effect on the Fe measurement, it has an adverse influence on the aluminium signal, and the belt speed should not exceed 0.1 m/s if good accuracy is required. Static trials on a 460 mm rubber conveyor belt with constant ore geometry indicate that for iron an accuracy of ¦ 1.2% Fe (2a) can be achieved for crushed run-of-mine ore at

Jan 1, 1978

The effects of changes in sintering bed height, coke fuel, suction and basicity on sinter productivity, physical strength and mineralogy were determined. It was found that, for a given iron ore, there is a narrow -coke range which maximises sinter strength, irrespective of bed height (in the range 300 to 500 mm) or basicity (in the range 1.2 to 2.2). Increases in bed height, at a constant coke level, improved the physical strength of the sinter. Productivity increases were obtained by increasing the sintering suction but, at coke levels other than the optimum, these *ere somewhat offset by the decrease in sinter physical strength. At basicities higher than 1.2 (i.e. 1.6, 1.8 and 2.2) there was a narrowing of'the size range of product sinter, with a decrease in the percentage of top size material, and a decrease in the amount of fines produced. Changes in coke, bed height and basicity exert major effects on sinter mineralogy, while the Nagoya index was mainly influenced by cote and bed height Changes.

Jan 1, 1975

By Choulaj D

Mining and petroleum continue to be the two most vita components of our nation's development, says Sir Julius Char in the Australian Journal of Mining (Nov-Dec 1996). In fact the} account for 71.6% of export earnings, and 21.2% of Gros; Domestic Product in Papua New Guinea. The Misima and Porger, Mines, along with the Kutubu oil project, have essentially rescues PNG's economic viability since the loss of income from Panguna Though the industry cannot create employment in the manner o. intensive industries such as agriculture, it does provid( opportunities to local communities in terms of jobs, financia compensation, and infrastructure. Many ventures take many years and enormous capital investment to set up. There are three phases: exploration, feasibility, an( operations. The operations phase sees a massive development o infrastructure, or the actual `building' of the mine. For mining companies to commit to such lengthy time frames and high level: of investment, without returns, requires confidence and a degree of commitment from government on a number of levels - legislative stability, monitoring social development, and the provision o social infrastructure.

Jan 1, 1997

By Rais SA

In June, 1986, Freeport Indonesia, Inc., in conjunction with Out- okumpu USA, laboratory tested the Flash flotation concept on Primary ball mill underflow. These laboratory results indicated a possible 10% increase in precious metal recovery and 0.6% increase in copper recov- ery were available over conventional methods. By October of the same year two Outokumpu Skim Air SK-240 units were operational on one mill circuit and were achieving 5 to 10% increased recovery in precious metals with equal copper recovery at one percent higher final concentrate grade. Two more cells were purchased and installed on the remaining grinding circuit in July, 1987. As part of the installation of the Skim Air cells, an existing cluster of six 508mm Krebs cyclones were replaced by four 660mm Krebs cyclones. To reduce high circulating loads, these new cyclones were made horizontal at 45 degrees. This arrangement succeeded in reducing the mill circulat- ing load by 100% and has allowed for a 10% increase in throughput at the same grind.

Jan 1, 1988

By A Purvee, M F. Lee, L J. Mollison

Oyu Tolgoi is a large Cu-Au porphyry deposit in the south Gobi desert, Mongolia. The first of several deep, large-diameter, concrete-lined shafts, Shaft 1, is nearing completion. It will have a finished depth of 1380 m at a diameter of 6.7 m. These shafts will provide access to and hoisting capacity for block caving of deep underground ore. Geotechnical site investigations, and associated predictions of stability and ground support requirements, are compared against actual construction performance. Routine mapping is essential, along with checks against predictions and informing the contractor of ground conditions and variances.Advance rates are compared against predicted rock mass quality. A reasonable correlation exists between Qwall and advance rate. Overbreak and concrete liner thickness is related to the blockiness quotient, RQD/Jn.A ætool-bagÆ of just a few support elements (chain-link mesh, fibrecrete and 2.4 m long friction anchors and resin grouted re-bar bolts) was able to cope with the ground conditions encountered. QA/QC procedures are essential from the factory, through site storage to installation.

Jan 1, 2008

By Lennox A

In an attempt to increase underground productivity Coal and Allied has introduced a continuous haulage unit into it's Moonee colliery. A second unit is planned for Nallarah colliery in the near future. Both systems will be roof mounted or monorail type and manufactured by Joy Manufacturing Pty Ltd. The introduction of these machines is seen as a logical step in improving the efficiency of mining with continuous miners. This could be in conjunction with longwall mining in the rapid development of gate roads or, as in the case with these machines, as conventional development and extraction units. The advantages of the continuous haulage system are; Relatively low cost. 2 Ability to obtain high productivity in irregular or disturbed coal reserves not suitable for longwall mining. 3 Increased worker safety with the elimination of shuttle cars and the majority of trailing cables. 4 Increased productivity independent of soft or difficult floor conditions. At the time of writing the Moonee installation is 6 months old. The Nallarah machine is due for delivery March 1988.

Jan 1, 1988

This paper deals briefly with productivity-enhancing advances in shaft sinking technology in South Africa post-World War II in general and the developments and application of long rounds since the 1980s in particular and is amply illustrated.It touches on the conversion to circular section, concrete lined shafts, the introduction of tungsten carbide drill bit inserts and grab lashing; expounds the rationale driving the development of longer rounds; and then describes the evolution of long rounds using hand-held and mechanically mounted rockdrills in South Africa and Canada by both local and foreign contractors. The recent experience gained on the sinking of the South Deep Main Shaft follows. Results obtained from this experiment are tabulated and commented upon. The paper concludes with the postulation of æwhat nextÆ and æwhere toÆ scenarios. Addenda include a list of shaft rounds in excess of three metres in length blasted in the Main Shaft at South Deep and their results, typical round design, manufacturerÆs specifications for the 6 m shaft jumbo and rock drills.

Jan 1, 2002

Alcoa of Australia's Del Park mining op eration is centred 9 km. east of the Pinjarra alumina refinery, and is centrally locatedwith- in the 10, 000 sq. km. lease which the Company holds for bauxite in the Darling Ranges. An- other mining operation is situated near the township of Jarrahdale, and supplies bauxite to the Kwinana refinery. Definition of the bauxite ore, development works and mining to the ore haulage stage, are identical for both mining operations. Exper- ience, and production cost figures, obtained from the Jarrahdale mine, where 100 tonne trucks are used to haul ore to a fixed crushing plant, led to the development of the Del Park mining concept with increased mobility of op- erations. The crushing-conveying-stockpiling arrangement at Del Park consists of a 1200 t. p. h. mobile crusher feeding bauxite to an overland conveyor system which transports the ore approximately 6. 66 km. to the stockpile area in the refinery. In the refinery raw mat- erials area the bauxite is distributed into 200, 000 tonne stockpiles by means of a travel- ling boom stacker.

Jan 1, 1973

The Curragh coal mining operation was designed and constructed to produce two coals initially at a rate of 4.3Mtpa. These are a high thermal energy steam coal primarily for domestic electricity generation and a low ash high quality coking product for the export market. Treatment of coals from four seams to achieve this requires a large and complex preparation plant and blending facilities incorporating state of the art technology. This facility was constructed during 1982/83. It has been designed for expansion to 6.8Mtpa capacity. The preparation and handling facilities were built at a cost of approximately A$80 million. Equipment includes 500 plus electric drives with a total capacity of 20 000kw. Commissioning was carried out in three phases : Staging - of the control system Coal Handling Facilities - conveyors, stackers and reclaimers for raw and product coals The Coal Preparation Plant - heavy media cyclones and froth flotation. A period of three months was devoted to the commissioning of the plant before requiring product coal to contract specification. This paper will describe the planning, implementation and results achieved.

Jan 1, 1986

The economic future of the Palmer Goldfield lies with both the gold mining and the tourist industries. An equitable solution to the competition between the two involves putting a dollar value on the historical evidence there for our Australian heritage.On 23 October 1986 the Queensland Government gazetted the Palmer River Reserves R16 of 16 200 hectares, in recognition of the competing land uses emerging in the region. The intention is that historically significant gold mining sites and relics will be preserved in situ with provision for continued gold exploration and mining.This paper explores and explains the administrative process of achieving a set of Management Guidelines for Rl6 within the Queensland political milieu. The result of that process is the achievement of some of the highest preservation standards in Australia, prohibiting surface disturbance of defined Category 1 sites, and no mining proposal has yet been refused approval.The Palmer Goldfield R16 experience is a major step in achieving a co-ordinated approach to both current mining and preservation of Queensland's mining heritage.

Jan 1, 1990

By Lai KF

The Hellyer orebody is a fine grained, massive sulphide Pb-Zn-Ag- Cu-Au deposit located in western Tasmania. Initial testwork showed that the orebody would be difficult but not impossible to treat by conven- tional flotation. A staged programme-of work was commenced to demon- strate that marketable concentrates could be produced with satisfactory recoveries. Following laboratory testing of drill core to define two flowsheets, bulk samples of Hellyer totalling 20,000 tonnes were trialled at 6 tph in the Cleveland concentrator over six months. The high through- put and extended duration of the trials ensured maximum confidence in the results and that scale-up to subsequent plants would be with a mini- mum of risk. The milling trials were successful and the Cleveland concentrator was expanded in early 1987 to treat 250,000 tpa of Hellyer ore to produce 85,000 tpa of bulk concentrates. Late in 1987 construction commenced on a 1 mtpa concentrator at Hellyer to produce separate copper/silver, lead, zinc and bulk concentrates.

Jan 1, 1988

Consolidated Rutile Limited (CRL) was one of the best performing mining stocks of the turbulent 1980s, having a very high payout of franked dividends. In contrast to some other mining groups, it was not highly involved in the speculative lead-up to the 1987 sharemarket crash. Its base was firmly laid through a succession of decisions that were taken in the period 1982-1985. These decisions and the rationale behind them are outlined in this paper. CRL began the 1980s in a highly favourable position. It had successfully pioneered the transition to high-throughput mining of the high dunes on North Stradbroke Island (NSI), commissioning its 2100 tph cutter suction dredge at the Bayside reserves in 1978 at the time of rising prices, such that it was able to pay off its modest bank loan within 18 months. The June 1980 results showed a record after-tax profit of $5.6M, from total assets fo $26.5M and sales tonnages of rutile and zircon of around 50,000 tonnes each.

Jan 1, 1991

The precious metallogenic belt and its geoloqical-tectonic location in eastern China.The precious metallogenic belt of eastern China is located in the western part of the Pacific gold metallogenic belt, and occurs in the upper levels of the continent cut by a deep fault structure tending NNE and NE, and active during the Mesozoic. The precious metallogenic period ranges mainly from Late Jurassic to Early Cretaceous (160 Ma-110 Ma); subordinate mineralisation occurred during the Hercynian period, and was rare in the proterozoic.Seven precious metallogenic belts are recognised from east to west, i.e. from continent to the margin active belts, as follows:1. Au-Ag-Te metallogenic belt of East Shandong Province2. Au-Ag-Pb-Zn metallogenic belt of west Liaoning-Miyun area3. Au-Os-Ir-Cr-Cu Mo metallogenic belt of Chengde Pingquan area4. Au-Ag-Pb-Zn metallogenic belt of Zhang Xuan area5. Au-Ag-Pb-Zn metallogenic belt of Zhejiang province6. Au-Ag-Se metallogenic belt of East Qinling area7. Au-Pd-Cu-Mo metallogenic belt of Wansu area

Jan 1, 1990

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

By B Clements, R Dunne, J Dioses, S Hart

In April 2003 plant upgrades in the æLow GradeÆ Cadia Hill circuit were undertaken in order to improve concentrate quality and metal recoveries from the flotation circuit. The major changes involved: circuit reconfiguration to allow all concentrates to be reground to less than 38 ¦m prior to final cleaning; increasing ball charge in the regrind mill to fully utilise all of the installed power; desliming of the cleaner scavenger concentrate to improve the circuit water balance; and the inclusion of a gravity concentrator in the regrind circuit to recover more free gold to bullion.Once the flotation circuit had stabilised under the new operating conditions concentrate launder modifications and increased froth crowding on the scavenger flotation cells permitted the introduction of stronger collectors without compromising concentrate quality or circuit stability.Twelve months on, the copper concentrate grade has increased by two per cent and metal recoveries increased by three per cent and seven per cent for copper and gold respectively. The project capital outlay of approximately $2.0 million has been repaid in less than three months. This paper will review the project from the design, construction and commissioning perspective as well as the subsequent debottlenecking exercise that was required to eventually yield the full benefits of this upgrade.

Jan 1, 2005

By J S. J van Deventer, D C. Shallcross

New developments are taking place in the recovery of gold from leached pulps that are based upon the adsorption of the metal cyanide species onto ion exchange resins. Despite the success of several resin-in-pulp pilot plant operations in the Western World and large-scale plants in the former Soviet Union, the process is yet to gain recognition as a viable alternative to the carbon-in-pulp process. An experimental research program has investigated the use of a variety of different types of resins for the recovery of gold, but to-date no resin studied has the desired properties of high selective loading capacity for gold cyanide and a simple inexpensive elution procedure. In addition very little is known concerning the physical strength of resins and their ability to resist shattering due to osmotic shock during cycles of adsorption and elution. The ability of ion exchange resins to enhance the leaching of refractory and re-adsorbing ores has not been investigated. This paper highlights the necessary factors that need to be addressed before commercialisation of ion exchange technology for gold extraction is feasible.

Jan 1, 1998

By Muir DM

In recent years, significant improvements have been made in the design and operation of carbon-in-pulp plants. Some of the major developments in plant operation and technology are reviewed together with an outline of the research being undertaken in Western Australia. The main problems facing operators include the understanding and control of carbon fouling and regeneration, and the recovery of gold from the carbon. It is shown that carbon fouling by a variety of agents, particularly cyanide, calcium carbonate and silica, cause a significant loss of kinetic activity which in turn leads to poor plant performance. The importance of acid washing and adequate thermal reactivation is discussed. Although the Anglo elution procedure is commonly used in South Africa its use in Australia in preference to the conventional Zadra elution procedure is likely to be re- stricted because of its demand for high quality water. Solvent elution by the recently developed Micron procedure using refluxing methanol, ethanol or acetonitrile vapours is an attractive alternative. This elutes gold in 4-6 hours and provides concentrated gold solutions suitable for simplified gold recovery steps.

Jan 1, 1984

By D Connelly

The initial results for the cyanide leach gold recoveries were very poor on a high-grade primary sulphide ore of 6.2 g/t Au with no silver. Subsequent mineralogy showed the ore to be a characteristic pyrite, carbonaceous refractory gold ore (double refractory). This was a very disappointing finding. A small scale gravity and flotation test programme was developed to produce a concentrate with the majority of the gold. This also failed with most of the gold remaining in the tailings. An ICP scan also showed variable levels of antimony. A Desktop Study was undertaken with minimal laboratory test work looking at Pressure Oxidation (POX), roasting, ultra-fine grinding, graphite passivation and consideration of any new technologies that might be applicable to this type of ore. The subsequent Study highlighted how difficult these double refractory gold ores are to process and highlighted some recent technology developments may be applicable. CITATION: Connelly, D, 2018. Technology options for processing complex and double refractory gold ore, in Proceedings Complex Orebodies Conference 2018, p 94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By C Catania

Mining companies and operations across the globe typically target best practice financial management, along with a focus on economically driven mine plans. Not only is this inherent in running a successful mining business, but also critical in addressing investor scrutiny. The standards for social and environmental practices is less consistent than this, with most companies adopting standards that are driven through legislative and compliance requirements of the nations in which they operate. Although there is still room for improvement, Australian is a country that stands at the forefront of social and environmental legislation, driving more sustainable planning practices for mining operations, with an ever-increasing focus on mine closure considerations. Of the many nations yet to reach such a legislative position, Kazakhstan is a place where some companies are driving towards world class standards beyond what is government mandated. CITATION:Catania, C, 2018. World-class mine planning for a sustainable future in Kazakhstan Mining, in Proceedings Life-of-Mine 2018, pp 6–7 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018