Search Documents

A review of all major TBM projects from 1974 to 1990 has been undertaken and the results entered into a database. A similar database was prepared from information obtained from a principal TBM manufacturer covering the period 1952 to 1990. The database includes information such as machine specifications, machine performance data, tunnel specifications and ground characteristics. The database can be used as a guide to gauge potential machine performance in a range of ground conditions and tunnel geometries. The review also indicates that current TBM technology is limited to certain ground strength conditions.

Jan 1, 1993

Bacterial leaching of sulfide minerals are fairly well established in heap, dump and in situ leaching and the primary bacterial treatment of refractory gold concentrate using CSTR have gained industrial prominence in recent years. Three cultures, a mesophile T ferrooxidans (DSM583), a moderate thermophile Sulfobacillus acidophilus (strain YTF1) and a extreme thermophile (Sulfolobus strain BC65) were used for the biooxidation (pre-treatment) of the Porgera gold-bearing pyrite concentrate under optimum O2 and CO2 enriched air (30 per cent O2 and ten per cent CO2) based on volume ratios. The positive effect of using oxygen and carbon dioxide enriched air for the biooxidation of gold-bearing pyrite mineral was clearly demonstrated where an increase in Fe release rate by a factor of 2.8, 1.8 and 1.5 for DSM583, YTF1 and Sulfolobus respectively were observed compared with the shake flask tests. The lag phase observed with the other test conditions such as in shake flask or with air decreased by about 80 per cent for all three cultures. The average observed dissolved oxygen concentrations in the pulp for these tests were 8.7, 5.8 and 5.0 mg/L for DSM583, YTF1 and Sulfolobus respectively, indicating that O2 was not limiting in these tests. The pulp redox potential was observed to increase with time for all tests coincident with the leaching rate and reaching a maximum of 663 mV, however the maximum value differs for each strain, with DSM583 exhibiting the highest followed by YTF1 and Sulfolobus. Biooxidation of pyrite under optimum gas enrichment at different pulp densities showed near total Iron extraction occurred for pulp densities of three, ten and 20 per cent (w/v). At high pulp densities, more so at 40 per cent than 30 per cent (w/v), the leaching rate decreased rapidly for tests with YTF1 and Sulfolobus. Monitoring of dissolved O2 shows that O2 demand increased with increasing pulp density and the average dissolved O2 concentration observed for YTF1 and Sulfolobus at 40 per cent solids concentration was 1.0 mg/L and below, suggesting limiting oxygen and carbon dioxide conditions for these two cultures. The decrease in leaching rate observed at high pulp densities (30 and 40 per cent) under optimum gas enrichment was accompanied by low metal dissolution and low redox potential values which was attributed to shear stress due to attrition of cells by high solids concentration, toxicity of metal ions especially Ag and Fe and the formation of precipitates and jarosites as confirmed from XRD analysis of leach residues hence impeding the leaching process. Limiting conditions due to high pulp density and viscosity were only observed for YTF1 and Sulfolobus. The subsequent cyanide leaching for precious metals from the pre-treated pyrite concentrate in all cases shows the extent of gold and silver recovery increased with the degree of pyrite oxidation and Au and Ag recoveries in excess of 80 per cent were achieved compared with only 18.1 per cent and 35.9 per cent for gold and silver respectively when treated by direct cyanide leaching on the original, untreated concentrate.

Jan 1, 2004

The Iron Prince orebody occurs within the Lower Middleback Jaspilite Horizon of the Middleback Group and consists of hematite within host rocks of jaspilites and schists. The ore was probably the product of leaching of silica from jaspilites and replacement by iron, concentrations occurring in suitable structural traps. The narrowness and the presence of extensive dolerite amphibolite dykes within the orebody make it essential to operate a grade control programme in advance of the faces. Information from drilling is drawn up on bench plans, step plans and impurity overlays, and these serve both in day to day production planning and in long term planning. Mining is done selectively by open-pit methods and blending conducted by keeping at least three faces of different grades of ore open at any one time. No stock piles of ore are kept for blending, but contact ore, contaminated ore and enriched material are dumped for later beneficiation.

Jan 1, 1971

A laminar-flow furnace was used to study the combustion of four flotation concentrates (chalcopyrite, pyrite, galena, and sphalerite) in air at temperatures up to 1400¦C. A special- Iv developed two-colour pyrometer was used to measure the temperature of individual chalco- pvrite and pyrite particles as they underwent combustion. Chalcopyrite and pyrite ignited with very high rates of reaction at air tempera- tures above 480 and 600¦C respectively, forming molten products. Galena and sphalerite required temperatures in excess of 700 and 1200¦ respect- ively to attain equivalent rates of reaction. The high rates of reaction for galena and spha- lerite were caused by vaporization. Temperature measurements for chalcopyrite and pyrite are reported here, together with vaporization measurements for chalcopyrite, galena, and Sphalerito

Jan 1, 1980

By McNabb KE, Ward B, Dyer G

Roof conditions at Southern Colliery, the second longwall mine to be established at German Creek, were found to be much stronger and more massive than at the earlier longwall mine on the lease. Investigations were made to ascertain the level of face support required for longwall extraction under the changed geological conditions. Geotechnical information was provided from drillholes and highwall exposures. Downhole geophysical logs, notably the sonic velocity log, were used to obtain a distribution of the major lithological units over the mine area. A representative type section of the strata and geomechanical properties was compiled to form the basis for numerical modelling. Two-dimensional finite element methods were used to predict strata movements and chock loads under cantilevered roof conditions. The model incorporated a 6.3 in thick roof beam either bonded or detached, with either a 2 in or 5 in overhang. The solid rib, immediate roof, chock support and goaf were modelled as distinct parts, in addition a front abutment stress profile, derived from three-dimensional displacement-discontinuity analysis, was superimposed on the model.

Jan 1, 1992

By M Bouare, C Holland, K N’Diaye

Two adjacent open pits in Mali hosted by deeply weathered saprolitic materials were mined consecutively over the course of approximately 12 months. During excavation, both pits experienced significant displacement and tension cracking as the result of deeper than expected depth of weathering coupled with relatively steep slope angles and significant groundwater. In response, geotechnical and operations teams overcame numerous monitoring challenges with prisms and radar to develop a simple and effective monitoring system coupled to a Trigger Action Response Plan (TARP) which enabled continued safe operations while reducing ore loss. Observations of previous slope performance of these two pits allowed for greater confidence in empirical failure runout calculations that was used to specify the standoff widths for the exclusion zones in the pit. Back analysis of the slope as-built performance after the first indications of slope distress was also conducted. The back analysis was used to confirm rock mass parameters for modelling while being utilised as a reality check for the stability analysis. The stability analysis indicated that leaving a large step-out or buttress would not prevent the displacement, resulting in some ore being sacrificed to ensure the safety of personnel. Key learnings from this experience highlight the importance of: • up-to-date geological interpretation of the depth of weathering • ensuring slope design guidance is reviewed and updated as latest information (ie geology and monitoring) is received • having multiple complementary slope monitoring methods to ensure redundancy • ensuring visual observations and as-built performance are utilised as a reality check to provide greater confidence in stability analysis and design guidance.

Jun 22, 2022

An empirical method of estimating dense rock (D.R.E.) equivalent volumes erupted as airfall tephra, described in a companion paper in this volume, is elaborated, and its accuracy discussed. Estimates obtained from a single eruption can be classified as to whether they show positive, negative, or constant relative dispersion. For positively dispersed tephras (estimated volumes increasing with distance), this procedure improves the accuracy of the method. The technique is applied to selected andesitic tephras erupted from Egmont Volcano, New Zealand, during the last 28 000 years, which are found to range in volume from about 1.5 x 107 m3 up to about 2.4 x 108 m3 D.R.E. With a factor of about 16 between the smallest and largest volumes, this contrasts sharply with the rhyolite volcanoes in New Zealand, where the difference factor is usually of the order of 100. The largest tephra eruptions at Egmont are small compared to the largest debris avalanches, which have exceeded 1010 m3 (10 km3) in volume.The magnitude versus frequency relationship, calculated using a maximum likelihood method, establishes the limits of eruption magnitude at Mt Egmont as 107 to 109 m3 D.R.E. For some volcanoes, the magnitude-frequency relationship changes with time, owing to clustering of eruptions, separated by long dormant intervals. Ngauruhoe Volcano, New Zealand, is an example. Within eruptive episodes, the mean interval between eruptions of >_ 105 m3 is about 0.9 ¦ 0.65 years. The mean interval between eruptive episodes in which >_ 106 m3 is erupted, including episodes in which this volume is erupted gradually, is about 25.8 ¦ 6.6 years, and the mean dormant interval between all episodes is about 5.2 ¦ 3.0 years. At present Ngauruhoe is in an unusually prolonged dormant period, 50% longer than any in the historical record, since 1839.

Jan 1, 1990

By Whiten WJ, Narayanan S

Data from ball mills of a wide range of sizes are analysed using detailed mathematical models and non-linear least squares fitting techniques. This analysis reveals that the relative power inefficiency of large ball mills is due to inefficient grinding of coarse (plus 4 mm) particles in these mills. A qualitative physical hypothesis is proposed to explain this behaviour. The results of the analysis can be used to scale up ball mill behaviour, using the mathematical models and techniques developed. A simpler ball mill scale-up procedure is also proposed, and its limitations stated. Laboratory experiments are being conducted to determine the average size distributions of single particles of different ores after breaKage. These experiments can distinguish between the different ores, and it is hoped to use their results to model and predict the grinding of different ores in ball Mills.

Jan 1, 1978

By Lawrie DC

Finely ground beryl was decomposed by mixing with ground limestone and soda ash andheating at 900¦C for,4-6, hours.The sintered material was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hours. The liquor containing Be, ; Al, . Fe and, other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either' by filtration or by decantation washing.The clarified leach liquor.was first treated to remove Fed}: , by contacting with a primary amine-kerosene solution in2 counter-current stages. The iron free liquor wa,s then passed to a 4-stage counter-current extraction unit where it was con-tacted with 0.5M di-(2 ethyl hexyl), phosphoric acid (EHPA) in kerosene. The'operating conditions were such that at least 99 p'br cent of the Be and only 7' per' cent of the Al- was, extracted The ,B6`= and. Al were ;stripped from the organic phase by sod-ium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipTitated a's Bo(OH)2 by-hoating the alkaline solution to 90C, the Al remaining in solution. After filtra-tion and washing, the Bo(OH)2 could be ignited directly to BeO at about 1000 C or used as a feed to further purification stages aimed at producing "nuclear grade" BeO.A small coaAter-current extraction unit was operated con-tinuously using liquor derived from the sintering and leaching stages. Data obtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precip-itate contained more than'99 per cent BeO.

Jan 1, 1963

By A Cheatle

GoldcorpÆs Musselwhite mine in north-western Ontario, Canada has in recent years become a world-class deposit. Initially discovered in the early 1960s by Alan and Harold Musselwhite, the then marginal mine eventually started production in 1997 and has to date produced 2.6 Moz of gold. Two million ounces of gold are currently classified as Mineral Reserve and a further 1.2 Moz of gold are classified in the Mineral Resource category for a total gold inventory approaching 6 Moz. Growth of the mineral inventory has been achieved through the successful implementation of strategic planning that sought to extend the mine life through discovery of additional economic zones and increased mined tonnages. Accelerated exploration activity commenced in 2001, at a time when gold price was at its lowest in decades. Focus was placed on building, developing and retaining a highly skilled geological team, maintaining purpose, conducting external reviews and developing a new geological model through research partnerships. Ongoing collaborative research between Lakehead University and Musselwhite mine has seen the development of new structural and geological models through post-graduate and academic studies. Research has included lithogeochemical, stable isotope and structural and metamorphic studies and has led to the evolution of a new mineralisation model (for the mine) and the recognition of brittle and ductile deformation regimes within the mineralised horizons. Exploration drilling continues to provide support for the new geologic model. Gold discoveries have extended known mineralisation 2.3 km along strike from mineral reserves and laterally into parallel zones. The exploration potential to further increase production rates, Mineral Reserves and Resources remains very positive and increases in overall gold inventory are likely. Musselwhite mine has significantly exceeded initial projections for a ten year life-of-mine and a marginal existence.

Jan 1, 2009

By Fletcher A. E W

Ever since it made its debut in 1962, in the form of a Robbins 31R, the raiseborer has become an accepted tool in the mining and civil construction industries. The first raiseborer to be used in the Witwatersrand goldfields made its appearance in 1968. This was a Robbins 42R which could raisebore 185m deep holes to 1,22m diameter. From 1968 to 1973 capability increased with the introduction of first the 61R, then the 71R and finally the 83R, which could raisebore 610m deep holes to 3,66m diameter. This created a demand for larger holes but the cost of bigger, more powerful machines requiring larger, stronger drill pipe, cutters and other accessories was prohibitive. To avoid replacing existing models such as the 71R, and in order to increase their capability, the concept of reaming in two stages sequentially was developed jointly by a German drilling equipment manufacturer, Wirth, their South African subsidiary, Transbor, and a local contractor, Rocbor Raiseboring and Mining Contractors. The result, the Sequential Reaming Head, proved most successful and existing machines, normally limited to 2,44m diameter holes, could now ream to 3,66m diameter. This created a demand for even larger holes. In order to maximise the use of the sequential reaming head to meet this demand the HG330, and subsequently the HG330SP raiseborer were developed. Using a 4,26m/6,02m cutting head, these machines have raisebored holes 1000m deep in hard rock. The raise- boring of the first major hole to be excavated by this combination, the 484m deep x 6,02m diameter surface shaft at Premier Mine is described. Reference is also made to six other shafts which have been completed or are under construction.

Jan 1, 1987

This paper aims to address the issue of the public's image of the extractive minerals industry. What is it about the industry that incites such negative feelings and are they justified? Are we really the 'rapists of the land' that many would have us believe? Has the industry really not improved since the old gold boom days?   I believe that the fundamental cause for the public's view is lack of knowledge and understanding of the industry as a result of the dislocation of the end production from its source. There are few people who look at a house, car, record, toilet, tooth-brush, bottle of coke or pair of glasses and see the mine site that supplied the source material. But the mine site and its products should be inseparably linked. This is one area where we should be educating the public û it is all very well being anti-development but the population as a whole is not really prepared to live without its 'mineral'-derived necessities. It is very easy to say that we do not want minerals development in New Zealand but are we prepared to live with the consequences, ie go without its products? We have a duty as a global citizen to develop our own resources rather than expect Third World nations desperate for overseas investment, often with governments who are not prepared to constrain or control their development, to be exploited. New Zealand is not the only 'beautiful' place in the world and we should be aware of the impact that our demands for resources have on the countries who supply us. We have a duty to be a good global citizen.   So how does the industry improve its public image? The key here has to be to educate. This does not have to be high powered or expensive but can be as simple as getting a few local kids' hands dirty panning, and gaining some firsthand knowledge of the industry. The industry also needs to be more pro-active in the public arena. Yes, the industry has skeletons, but the industry should be publicly displaying them û admit that things have gone wrong but let's do it ourselves and not leave it up to the environmental groups to accuse, point the finger and put the industry under public scrutiny. The industry should also be publicising its successes, inviting the local press, councils, etc to view the latest area rehabilitated. But more than anything else we must tell the public what the minerals industry means to New Zealand. Can they really live without us?

Jan 1, 1991

By Simpson JF, Murrie SJ

In determining new areas for slag disposal a foamed slag aggregate has been developed for use as a skid resistant material. The foaming of the slag does not rely on the use of water, but rather on the slag chemistry. Laboratory test results indicated that a product having good skid resistant properties has been prod- uced. A section of road is being assessed for performance of the aggregate in a surface dressing application under heavy load. The results from the test section after seven months have shown that the foamed slag is suitable for this application. Further test sections are now being considered.

Jan 1, 1979

By R Bunduwongse

The oil crisis had repercussions throughout the world and most importantly on mining, where the drive to reduce the use of liquid fossil fuel led directly to the appearance and subsequent growth in the design of mobile crushers in late 1970s early 1980s, which heralded a new era in both quarrying and mining. Even though mobile crushing has now become common, even preferred in the quarrying industry, this has not been the case in mining. This paper looks at why, in spite of the initial optimism, this technology has yet to gain full acceptance in the mining industry. The paper examines some of the problems that have been encountered in the past and offers suggestions as to how they can be avoided by applying the appropriate technology. It then takes a look at the successful application of the semi-mobile in-pit crushing system used by Italian Thai Development Company (ITD), on the Mae Moh Phase 5 contract and examines how the techniques used successfully there could be applied to the industry at large.

Jan 1, 2007

By D Craw

The Hyde Macraes Shear Zone is a mineralised low-angle shear within the Otago Schist traceable for ~30 km with a NW strike. It is been actively mined along 12km of this strike, producing >6 Moz of gold. The shear zone consists of greenschist facies rocks with a mineralogy only subtly different from that of the host schist. Pervasive fluid flow has occurred along grain boundaries and within microshears which have been enhanced by the deposition of hydrothermal graphite. We model the development of these microshears using a threedimensional numerical code. For an inhomogeneous initial rock with lithostatic fluid pressures and a dynamic permeability deformed under dextral non-coaxial flow, deformation is distributed into weak shear bands. Graphite deposition and associated reaction-softening has a dramatic effect on the development of model shear zones. Graphite is deposited into a shear band, weakening it and further localising the deformation into that shear band, producing an anastomosing and interconnected shear zone structure such as observed in the HMSZ. The degree of graphite precipitation and graphitic-induced weakening are varied in the models. More graphite precipitation with a low degree of reaction-softening results in more diffuse shear bands. In contrast less graphite deposition but with a high degree of reaction-softening more leads to the development of more focused shear bands. Graphite deposition has clearly controlled the formation of the HMSZ structure, and is an important indicator of potentially mineralised structures elsewhere.

Jan 1, 2007

By M McCurd, M Lynch, B H. Yin, S Mendoza, C W. Bumby, Y Iwasaki, B Rumsey

Iron and steel production is responsible for approximately 6.3 per cent of global anthropogenic CO2 emissions. Direct reduction of iron with hydrogen is a potential route for decarbonising the iron and steel industry. Extensive small-scale laboratory experiments have been performed to test the feasibility of hydrogen-direct reduction of iron ores sourced from diverse geographical locations. However, test results from the batch reduction of small-sample do not necessarily translate to continuous commercial-scale processes. Establishing a small-scale continuous test reactor for H2- DRI process is challenging, requiring substantial resources and investment. The limited availability of small-scale reactors that enable testing under relevant conditions has become a major obstacle for H2-DRI development, leaving a big gap between laboratory success and proof of commercial feasibility. Here, we report on the recent commissioning of a continuous counter-flow vertical shaft reactor, which has a processing capacity of 6 kg/hr iron ore pellets at up to 100 NL/min H2 flow. We believe this to currently be the largest H2-DRI facility in the Southern Hemisphere. In this talk, we will discuss the design and construction journey for this reactor, starting from the initial system design to the initial demonstration of H2 reduction of titanomagnetite ironsand pellets. This reactor now enables a range of research capacities, including the validation of laboratory results on a larger scale with practical operational variables, feasibility assessment of hydrogen direct reduction of different iron ores on a commercial scale; identification of scalability, sticking, and other potential issues before building a full-scale plant; and a viable solution for producing small-quantity DRIs for downstream melting investigations. Overall, this new research facility offers significant benefits for assisting the transformation of iron and steel production to a more sustainable and green industry.

Sep 18, 2023

By B Menzel, M Wlasenko, J Phillips

Yandicoogina (Yandi) open pit mine is located in the eastern part of the Pilbara region of Western Australia. It hosts pisolitic iron-oxide mineralisation distributed within a meandering paleoriver channel. The deposit is characterised by clays occurring as lenses, accretions, desiccation joint infill and voids in the pisolite ore. The irregular shapes and highly erratic distribution of these clay pods represent a serious challenge for grade control at this mine.The current grade control approach used at the Yandi mine is based on sampling of production blastholes on a 6 m X 6 m spacing. Their good spatial coverage, tight spacing and low cost make blastholes a very convenient media for grade control and ore-waste definition. However the potential downside of this grade control approach is poor sample representivity. An alternative grade control approach is to drill and sample using reverse circulation (RC) holes distributed on a 25 m X 25 m grid. This approach has been tested in Yandi mine and compared with the blasthole sampling approach for sample representivity. The impact of increased drill spacing on mining block predictions has been studied using a conditional simulation technique. Blasthole and RC samples proved to be similarly biased, underestimating Al2O3 and SiO2 grades and overestimating Fe grades, when compared to full cone assays. These results show that using RC drilling for grade control at the Yandi open pit will not necessarily improve the representivity of the grade control samples. However, increasing the grade control spacing to 25 m X 25 m will lead to more than 12 per cent of the selective mining unit (SMU) sized blocks being misclassified. This is approximately a two-fold increase in the number of misclassified SMU blocks in comparison with 5 m X 5 m spacing.

Jan 1, 2007

In 1972 the Marra Mamba Iron Formation in the Lower Proterozoic Hamersley Iron Province of Western Australia was recognised as a stratigraphic horizon with significant potential for high grade iron ore reserves. Within the Newman area the Marra Mamba Iron Formation has been subdivided into four strati- graphic units: Lower BIF member, Middle BIF and shale member, Upper BIF member and Upper shale member - and a standard natural gamma log reference section compiled for the entire formation. The recognition of the Upper shale member as an additional unit contrasts to the previously proposed stratigraphy. Enrichment of the Marra Mamba Iron Formation to ore grade (0)8 percent calcined Fe) in the Newman area is restricted to the Upper BIF member and to a lesser extent to the Middle BIF and shale member. Typical ore from Orebody 29 is friable interbedded martite-ochreous goethite, signifi aptly different both physically and chemically from the Brockman Iron Formation ores of the Tom Price-Whaleback type. Large scale customer acceptance trials (in excess of 4 million tonnes) have shown that Marra Mamba ore crushed to fines and blended with Mt. Whaleback fines in a ratio of up to 15:85 forms an acceptable sinter feed.

Jan 1, 1981

The Peko copper orebody is associated with a body of magnetite rock which it has partly replaced. The primary ore averages about 9 per cent. copper and 4 dwt. gold per ton and locally IS much richer. It consists essentially of chalcopyrite and unreplaced magnetite, with lesser amounts of pyrite, marcasite, pyrrhotite, cobaltite, bismuthinite, native bismuth and native gold. The earliest formed mineral is wolfram, and the latest formed is goethite, so that the temperature of deposition ranged from about 5000 C. to 1650 C. or lower.Oxidation extends to 270 ft., which is 100 ft. below the present water level. The oxidized ore consists of cuprite and native copper, and has replaced more or less massive chalcocite of a former zone of secondary sulphide enrichment. The present zone of secondary sulphide enrichment extends from about 270 ft. to 310 ft. depth.INTRODUCTIONThe Peko mine is about 6 miles south-west of Tennant Creek township in the Northern Territory, adjacent to a small outcrop of hematite rock that projects above an otherwise featureless "bull-dust" fiat.The copper-gold orebody being developed in this mine did not outcrop. It was first detected in 1950 by a surface diamond-drill hole (DDH.1), which intersected primary copper ore at a depth of 400 to 425 ft. This ore contained from 4 to 11 per cent. copper and 1 to 25 dwt. gold per ton. Since then a shaft has been sunk, and crosscuts and development drives have been opened on the 210..ft., 300-ft. and 400-ft. levels, which are also connected by winzes. Two diamond drill holes sunk from the 400-ft. level have intersected theorebody at about 450 to 460 ft., and a winze from the 400-ft. level intersected the lode from 445 to 500 ft. At this point it is 54 ft. wide, and averages 9 per cent. copper. More recently an inclined surface drill hole (Peko No. 1) has cut the lode at 856 ft. to 921 ft., equivalent to a vertical depth...

Jan 1, 1955

By Enever JR

In-situ rock stress measurements conducted in the Phillipines and on Bougainville have revealed stress fields significantly different from expectations based on intraplate experience. The results have potential significance in regard to both engineering practice in the Pacific Rim region as well as in helping to understand the geological processes occuring near subduction Zones.

Jan 1, 1987