Search Documents

By B R. Castley

Consumable materials used in mines are often transported to the working areas down shallow angle decline shafts, typically at anywhere between 10¦ and 30¦ to the horizontal. The winding equipment is usually a relatively small single-drum winder and the material is transported in one or more cars, running on rails in the decline. The winding rope is attached directly to the cars, which are mechanically coupled together. For small rock hoisting declines, the cars are replaced with hoppers or skips. The winder is normally of basic design, fitted with only the minimum required safety devices and very elementary brake control. Since these winders are not ælicensedÆ and are usually located in remote areas, the standard of maintenance on the installations is often poor, leading to frequent accidents, resulting in runaways, derailments and broken ropes. These problems can be overcome easily with the application of the rope haulage principle. When large volumes of ore have to be transported to surface, belt conveyors are used on shallow angle inclines, or high-capacity friction winders are used in vertical shafts. Conveyors are limited to inclines no steeper than 14¦ and vertical shafts with large friction or drum type winders are extremely capital-intensive. Rope haulage systems can be used on decline shafts where the inclination is too steep for belt conveyors and too shallow for conventional drum winders. Rope haulage systems also offer a variety of safety, technical and cost advantages over other winding and transport systems. This paper describes the adaptation of the rope haulage principle to modern requirements and, combined with 21st century electronic technology, explains how the principle can be used as an efficient, safe and practical solution to some problems associated with the transport of materials, personnel and ore in mines. The authors describe the designs, methods of operation, safety aspects, automated control, loading and unloading facilities of modern rope haulage systems used for transporting personnel, material and ore. This paper considers a variety of systems already designed for different applications, from small material-only installations to multi-purpose and large rock-hoisting systems with payloads as much as 180 t. It also describes in more detail, a material transporting system recently commissioned in South Africa.

Jan 1, 2005

By V S. T Ciminelli

This work aimed at evaluating the acid rock drainage (ARD) potential of five samples of a Brazilian gold sulfide mine in a decommissioning process. Three of the most traditional ARD prediction techniques, Standard Acid Base Accounting (Std ABA), Modified Acid Base Accounting (Modified ABA), as static methods, and humidity cells as a kinetic method were tested. Both the Std ABA and the Modified ABA results indicated an acid generation potential for some of the studied samples. In the other cases the results were inconclusive. The five samples were then submitted to humidity cell tests during 27 to 30 weeks. At the end of the period, the leachate pH was stabilised in a range from 3.4 - 4.1 (four samples) to 5 (one sample). The presence of relatively high levels of sulfate and dissolved metals was detected throughout the operation, specifically, Ni and Zn, and less frequently, As. These findings are discussed with the help of the samples mineralogy and Eh-pH diagrams. The results obtained in this investigation indicated potential environmental risks of this mining area. In this particular case, the kinetic tests were shown to be essential to the identification of the samples ARD potential.

Jan 1, 2003

By King RP, Kientzler P

In recent years, ultrasonic comminution technology has been developed at the Utah Comminution Center. An ultrasonic grinding device was assembled and investigated. An ultrasonic transducer system has been significantly improved by using a special type of piezoelectric ceramic and preloading to 4.1 x le kPa to obtain maximum strength. The improved system provides constant and rapid vibratory promotion of fatigue fracture resulting in more effective breakage. The design principles for an ultrasonic mill are developed in this paper. Size reduction was successfully achieved in the ultrasonic nip-roll device for a variety of materials. Ultrasonic comminution has repeatedly demonstrated the capability of producing fine particles from a variety of materials. A comparison between ultrasonic grinding and dry ball milling of limestone showed that the ultrasonic device produced much narrower size distributions than the ball mill. This trend is especially obvious in the coarse size range where few particles remain, and in the fine size range where overgrinding is prevented. This behavior might have some interesting applications in areas other than mineral processing like powder metallurgy or material science where narrow and controlled product sizes are required for the successful elaboration of high-technology ceramics and glasses. Ultrasonic comminution has a significant advantage in the accurate control of the product size.

Jan 1, 1993

Block caving is the lowest cost underground mining method but it has relatively high risks and a high up-front capital and development cost. It has application to large, often lower-grade orebodies where high production rates can provide good returns on the investment. However, it has a range of technical risks that are peculiar to block caving and the usual financial, political and environmental risks that may be exacerbated by the long lead-in times associated with the development of a block cave operation. With initial development costs that may be $100 M to $1000 M when the building of a treatment plant is also required, it is obviously important to minimise and manage the risks. In a greenfield project, commitment to a substantial proportion of the capital expenditure may be required to gain access to the deposit, and the decision to proceed at this stage would be based very largely on interpretations of drill hole data. In established mines the data may be supplemented by geological mapping and past experience, etc. The quality of this data is critical and yet it is frequently degraded through poor techniques and avoidable omissions. The final decision to proceed would be assessed on projected commodity prices, mining capital and operating costs, dilution and run of mine ore grades. The latter will vary over the life of the project and these can be estimated with drawdown or draw control modelling techniques. In this modelling, there are further risks in the assumed modelling parameters or that the modelling technique may not be applicable or appropriate. The paper addresses the most critical technical and operational risk areas and provides some practical precautions that can be taken to reduce these and improve the reliability of the geological and geotechnical models.

Jan 1, 2000

By A G. Sheard

Fire safety requirements inside tunnels have become more demanding as tunnel designers consider the impact of potentially larger fires. Tunnel ventilation equipment is required to clear hot gases in the event of a fire. This is vital to maintain smoke free escape routes for people trapped in the tunnel and to facilitate safe access for emergency services. As the fire becomes larger, the temperature of clearing hot gases increases. Traditionally, engineers have taken into consideration gas temperatures of 250°C when designing tunnels. Because of larger fires, engineers must now design equipment to clear hot gas up to 400°C.Increasing the temperature of hot gases to 400°C requires tunnel ventilation equipment that goes beyond historic limits. As temperature rises, material strength reduces, consequently mechanically constraining fan aerodynamic performance. Developing tunnel ventilation equipment suitable for clearing hot gases at 400°C requires a fan technology that is more typical of industrial turbomachinery. The standards EN 12101-3:2002 and ISO 21927-3:2006 defi ne the necessary design criteria and testing methodologies to verify that a range of tunnel ventilation equipment is capable of extracting hot gases.This paper describes the process by which the authors certified in accordance with EN 12101-3 and International Organization for Standardization (ISO) 21927-3 a range of powered ventilators suitable for clearing smoke and hot gases at 400°C for two hours. Proving the high temperature capability of the new range provided a challenge as a consequence of the large physical sizes and high motor powers involved. Additionally, the need to install vertically, as well as horizontally, imposed high thrust loads on motor bearings, further complicating both mechanical design and testing. The paper presents the methods by which the authors overcame these challenges.

Mar 8, 2011

By J St George

Much of AucklandÆs transport infrastructure has been developed on surface with little or no consideration of underground options. Current and planned transportation routes are now facing high costs due to land values and increasing environmental resistance to surface development. The option of utilising underground space becomes a feasible investment decision for these links as well as being the only option to develop the rail network within the inner city area. Transportation tunnels offer a quieter, more energy efficient means of getting around with minimal impacts on the surface environment. One of the major impediments to tunnelling is the high construction cost, which is partly related to the risks of encountering unexpected ground conditions and/or the possibility of causing surface ground deformations which could damage structures. The geology of Auckland has had substantial investigation through various studies and projects. The sediments of the East Coast Bays Formation (ECBF) underlie most of the Auckland urban area. It is classified as a soft rock and is a suitable material to tunnel through using either a tunnel boring machine or a roadheader. This paper reviews the limited amount of tunnelling completed in the urban Auckland area, together with the international advancements that have been made in the tunnelling industry. From the known features of the local geology and the problems encountered historically, the likely risks of tunnelling in Auckland are presented and ways in which those risks could be reduced and managed, are discussed. In addition, contractual arrangements between client and contractor are assessed with respect to complicated projects (such as tunnelling), so that the risks can be managed to create efficient infrastructure routes with reduced costs.

Jan 1, 2008

By R C. Morris

The channel iron deposits (CID) (Ramanaidou, Horwitz and Morris, 1991; Morris, Ramanaidou and Horwitz, 1993; Ramanaidou, Morris and Horwitz, 2003; Morris and Ramanaidou, 2007) are one of the two major iron ore types mined in the Hamersley Province. The CID provided around 41 per cent of the total of 268 Mt of iron ore mined from the Hamersley Province in 2006. The current CID resource is around seven billion tonnes. The CID deposits occupy numerous meandering palaeochannels in a mature surface that includes Precambrian rocks and ferruginous palaeogene valley fill. These palaeochannels are generally less than a kilometre but can range to several kilometres in width and from one metre to more than 100 m thick. The two currently mined CID areas are located:in the western Hamersley Province in the Robe palaeochannel, and in the east in the Yandi palaeochannel. These two major CID channels extend over 100 km to 150 km, with the Robe system up to 5 km wide. The granular ore facies typically contains ooids and lesser pisoids with haematite nuclei and goethite cortices, with abundant goethitised wood/charcoal fragments and goethitic peloids, minor clay and generally minimal porous goethitic matrix. Post deposition weathering is common and produced secondary facies.Ooids and pisoids were mostly derived from the stripping of a well- vegetated deep ferruginous surface. The peloids were derived both intraformationally from fragmentation and reworking of desiccated goethite-rich mud. Minute wood/charcoal fragments in the soil that were initially replaced by goethite and then dehydrated to haematite, formed nuclei for many ooids and pisoids. In addition, abundant, generally small (in situ by goethite within the consolidating CID. This profusion of fossil wood, both as ooids and pisoids nuclei and as discrete fragments as well as the local presence of kenomagnetite suggests major episodic wild fires in heavily vegetated catchments. The goethitic matrix was the result of chemically precipitated iron hydroxyoxides, resulting from leaching of iron-rich soils in an organic environment.

Jan 1, 2007

ADDRESS BY THE PRESIDENT OF THE INSTITUTE (MR. C. H. MARTIN) IN PRESENTING THE CERTIFICATE TO SIR MAURICE MAWBY, C.B.E.Members of The Institute, distinguished guests of which there are many, ladies and gentlemen, you are welcome. And might I add a special welcome to Lady Mawby and Lady Fisher and to Sir George's only son, Peter, who with his wife, Betty and one of Sir George's three daughters, Helen, are present this evening, and also to Sir Maurice's son, Colin, and Colin's wife, Jay, also in our company.The family presence must surely be a great source of pleasure and satisfaction to all those so intimately concerned.It is hardly necessary for me to state the sole and only reason for our presence here tonight, which is to confer on Sir George Fisher and Sir Maurice Mawby Honorary Membership of The Australasian Institute of Mining and Metallurgy, and at the same time to acknowledge two people who have rendered great service to the mining industry, albeit tinged with sadness to all of us in the knowledge that from now on their influence may diminish. It is now my pleasure to introduce, although that is hardly necessary, Sir Maurice Mawby, the second member of the duo we honour here this evening, and whose contribution to the mining industry is also beyond assessment.

Jan 1, 1976

We often read and hear, especially in the United States, that we are running out of critical metals. These are vague forebodings of stagna- tion or winding down of our civilization. Our technological progress has been rapid in the last 50 years and is still advancing at an accelerated rate, and predictions of its long-term impact on consumption and production of metals are more hazardous than ever in the light of the great economic and political shifts that are bound to continue. There are many factors that will have a hardly predictable but profound effect on pro- duction and consumption of metals over a time span of, say, 25 years. Among such factors are recycling, substitution, availability of capital, direct involvement of governments in financing and production, and the capability of producing much lower grade ores at possibly much higher prices relative to costs in the event of scarcity. I must state at the outset that my discussion of this topic does not take into account the role that deep-sea nodules containing copper, nickel, cobalt, and manganese may play, because I don't believe production from these deposits will be of much significance within the 25 year span I will be discussing.

Jan 1, 1978

My closest personal connection with the problems of rehabilitation comes from two years spent on a project at Weipa. At the beginning I am fairly certain that the engineers did not understand the mental processes of the ecologist they were dealing with. I am absolutely certain that the ecologist did not understand the minds of the engineers. This form of the two cultures problem is the root of some of the matters that lie behind this lecture. It is possible to establish a stabilising cover of vegetation on virtually any land surface, short of a cliff. While the biologist knows this he also knows that the physical and chemical nature of a given acre of land combines with climate to define quite sharply just what plants can be grown there. In the case of land after mining the range of plants may be quite limited. The engineer, and his masters in the accounting section, seem (in my experience) to expect that rehabilitation can be carried on with equal speed and facility in any location. This belief commonly leads to a situation where rehabilitation is not considered until mining is well under way. True, the mine must be proved as an assured profit- earner before money can be justified for the non-productive (to the miner) expense of rehabilitation. But when the miner finally starts rehabilitation he does not always get a convincing and speedy result. Furthermore, the failure may not be easy to overcome. This is even more likely to be the sequence of events if the miner wants, or is obliged, to specify the exact type of vegetation to be produced, e. g. commercial forest, pasture,' or the original native vegetation.

Jan 1, 1971

By Z Chang, S A. Mrozek, S Windle

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. It is important to understand skarn-porphyry transitions in order to use exposed skarns to look for associated and potentially larger porphyries. For such purposes, a good start is to understand the transition between porphyry and skarn in known deposits. In this contribution, we report the transition at Antamina, Peru, where skarns occur in and around a Miocene complex comprised of more than seven porphyritic intrusions. There are three types of skarn-porphyry relationships. The earliest intrusive phase, P1A, contains both endoskarn and porphyry-style quartz veins with secondary biotite halos. The porphyry quartz veins and endoskarns formed at the same time. Locally, the intrusion contains only endoskarn without porphyry quartz veins and is surrounded by exoskarns in carbonate wall rocks. In the third scenario, later porphyry (P2) intruding into P1A porphyry and skarns related to P1A contains abundant granular quartz veins and secondary biotite alteration but does not have significant endoskarn. The granular quartz veins also extend into earlier P1A skarns. The scarcity of endoskarn associated with P2 is related to the supply of Ca. The earliest P1A intrusion intruded into carbonates that supplied abundant Ca, therefore both endoskarns and exoskarns formed. In contrast, where the wall rocks of the later P2 intrusion are P1A or skarn related to P1A, there was little free Ca, therefore only porphyry-style quartz veins formed.CITATION:Chang, Z, Mrozek, S A, Meinert, L D and Windle, S, 2015. Skarn-porphyry transition – an example from the Antamina skarn, Peru, in Proceedings PACRIM 2015 Congress, pp 409–414 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Australia has a high level of research and development capabilities in government, industry and tertiary institutions. In the- remote sensing fields, we have developed a range of applications in geology, agriculture, infrastructure and environmental monitoring which are very cost effective and applicable to projects in the Asian and Pacific region. Support by the Department of Science through the Scientific Industries Steering Committee has enabled rapid penetration of this technological capability into projects with significant economic and financial benefits. It has also led to the opportunity for development of new sensors and processing systems, through collaborative projects with regional countries, which. will have applications in cloud covered, rainforest, and coastal tropical regions for geological and resource applications.

Jan 1, 1987

The Australian Mineral Industry's growth in the last two decades is directly related to the skill and experience of its consultants in mining, metallurgy, geology, finance, management, marketing, and engineering. The role of mining consultants needs to be re-examined, so that the quality of the service they deliver will continue to be adequate for the 1990's. One means of this evaluation is by examining Case Studies in the strategies and difficulties of developing contract and entrepreneurial research.

Jan 1, 1986

By Falbo A, Quarestima S, Cozza C, Barbaro M

A new synthetic reagent of the mercaptobenzoxazole class, 5- methyl-2-mercaptobenzoxazole, has been studied. This reagent exhibits powerful selective collecting action towards copper sulphides present in several complex ores, as demonstrated both by laboratory and pilot plant tests. Industrial production is expected to start in the near future. The way this reagent reacts with pure chalcocite has been studied utilising in situ FTIR techniques, adsorption tests, electrokinetic potential measurements and Hallimond cell flotation tests. The FTIR studies have indicated the nature of the surface phase. Adsorption isotherms obtained by the rest method have revealed the quantitative evolution of surface products, permitting the determination of surface coverage at various reagent concentrations. The electrokinetic potential has been utilised to verify the stability of individual species in diverse concentration ranges. Correlation of the results obtained has provided indications on the chemical interaction of this reagent with the surface and on the surface Arrangement.

Jan 1, 1993

By J E. Everett

An essential requirement of product quality control in the mining industry is to be able to reliably predict key quality properties of finished product from the data available before the extraction of the ore. From a production viewpoint, the unit of data collection is generally the input and output data set for each shift of crusher production, but could be any period where mine precrusher data can be reliably matched with product data.This paper demonstrates that linear regression models can be used to predict crush grades from blast grades, even where the crush material is blended from multiple sources or pits for each of which differing regression models might apply. The advantage of using increasingly complex regressions models to match the available data to give increasingly more powerful models is examined. The best model for any application will be a balance between required predictability, available data and the business’ tolerance for complex models.The regression modelling approach has several advantages over the more classic method of run-of-mine (ROM) crusher trials, which will be discussed.The models can use any predictor variable such as grade, geotype and in situ density provided the preextraction data set can be reliably matched with post-crusher data and is significant as a predictor. The models have been used extensively in the generation of the daily crusher plan with the aim of maintaining finished product grade. This approach has also been used associated with exploration drilling and long-term planning.It is acknowledged that there are inherent problems in fitting lump and fines grade to a linear model. However, these problems are minor when they are used for interpolation within the window spanned by the shift blend records used to produce the model. This paper discusses some of the issues limiting linear regression models in this application, and suggests methods enabling consistent models to be formulated

Sep 5, 2011

By D La Rosa, W Valery, A Jankovic, S Ese

Metso Minerals Process Technology Asia-Pacific (MMPT-AP) has been working with many mining companies worldwide performing æMine to MillÆ or Process Integration and Optimisation (PIO) studies. MMPT-AP has developed a proven methodology to improve the efficiency of the mine-mill interface and gain maximum benefit. The PIO methodology involves rock characterisation, mathematical modelling and simulation to generate a list of operational and control changes for both the mine and concentrator. Following the methodology, the list of recommendations is developed relatively easily; the more challenging part depends on the company. Success of a PIO project relies on the ability of an organisation to implement change û both operationally and culturally: the human element. When a PIO project is started, there is initial interest and commitment from the company. But how can this be maintained? How does an operation know if the benefit continues? MMPT-AP is now developing long-term relationships with clients to ensure that the increased production and improved efficiency continues. Direct and indirect measurements are used to determine the key factors involved and to understand the cause/effect relationships. Simulation tools also can be used to compare current with recommended practices û so when material properties vary over time, the benefits can still be quantified. PIO is about empowerment: by measuring and understanding what parameters affect concentrator performance, the site personnel now have the knowledge to make a difference. Rather than simply reporting variable or poor concentrator performance, operations can predict when production will be affected and put controls in place to prevent it from happening. This requires support and commitment from the company or æbuy inÆ. Ensuring this buy in continues is the challenge facing every company involved in PIO work û but the benefits are well worth it. This paper will review MMPT-APÆs experiences in implementing PIO projects in the long term: from both the consulting and operational viewpoints. MMPT-APÆs involvement with a number of companies will be discussed as examples of what works and what does not.

Jan 1, 2007

By S Watson, L Martinez

Mine projects are complex opportunities that demand a constant assessment of uncertainty, ie risk and upside potential. This is because the value of a mine project is typically influenced by many underlying economic and physical uncertainties, such as metal/mineral prices, metal/mineral grades, costs, schedules, quantities, and environmental issues, amongst others, which are not known with much certainty at the beginning of the project. But, is uncertainty an enemy or an ally of the mine planner/analyst? To answer this question, this paper first assesses and elaborates upon the general concept of uncertainty. It then looks at the different sources of uncertainty in a mining project, such as the orebody, costs and product price uncertainties, and their effect on the final project value. Next, a general?review?of current mine evaluation techniques highlighting their limitations when dealing with uncertainty is made. Finally, an extended evaluation and risk management framework that addresses the existing uncertainty in the (greenfield/brownfield) mine evaluation process is proposed. One important characteristic of this framework is that it uses and manages uncertainty in order to generate additional value to the project; this is done through operational and managerial flexibility, which allow mine planners to minimise/maximise project risk/upside-potential giving a more realistic estimate of the projectÆs market value - this is shown in practical and simple examples occurring at different stages of a mine project, such as exploration and operation. Final conclusions are provided at the end.CITATION:Martinez, L and Watson, S, 2012. Uncertainty - An important source of (additional) value for mine projects, in Proceedings Project Evaluation 2012 , pp 131-140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By Le V, Nguyen Ngoc Quynh, R H. Murfitt

The Truong Son Fold belt in Indochina hosts the significant Sepon gold-copper district (Laos) and the similar gold-basemetal districts of Phuoc Son and Bong Mieu (Vietnam). With over seven years of exploration, Toronto-listed Olympus Pacific Minerals Inc, is one of few foreign companies that have to date made a substantial investment in mineral exploration in Vietnam.Much of this work has been conducted along the Phuoc Son û Tam Ky Suture, on the south-eastern limb of the Truong Son Fold belt on the Vietnamese side of the border with Laos. These programs have produced a significant number of gold prospects at varying stages of exploration development. The Phuoc Son û Tam Ky Suture is a major Paleozoic subduction zone that extends from northern Laos, through Central Vietnam and out into the South China Sea.It represents a Lower Mesozoic collision zone between the Paleozoic-age Truong Son fold-belt terrain to the north, with the crystalline terrain of the Pre-Cambrian Kontum Block to the south. Since its formation, it has been a locus of deep faulting, continental accretion, intensive intrusive activity and mineralisation. This paper briefly discusses the geological setting, structure, metamorphism, mineralisation, exploration history, and proposed mining development of the Olympus Phuoc Son Gold Project, with particular reference to the Phuoc Son û Tam Ky suture.

Jan 1, 2004

I am honoured and very pleased to have been given the opportunity this evening to say a few words of thanks not only on behalf of all the guests but especially for the delegates and accompanying persons attending the 13th Congress of the Council of Mining and Metallurgical Institutions. Firstly, I would like to congratulate Sir Hamilton Whyte,KCMG for his most interesting address. In his far ranging talk, when he showed knowledge of widely diverse subjects, I had a brief fear that he was going to be talking about the details of support methods in deep level mines, or how to avoid flotation problems in multi-metal mines. Although he did not go that far, he touched on subjects which have arisen this week - long term planning and secure supply of minerals at acceptable prices. The dire predictions of the Club of Rome have been debunked with a far more elastic supply of minerals having been proved. Combined with the importance of a falling birthrate in some parts of the world, this will lead to many changes in the future, when hopefully governments will take the long term view rather than look at the next budget or the next election. Maybe some of them are not too lazy to do this for all of us. However as a fellow Ukranian, I feel that he might have been called something different if he had been in Australia. Sir Hamilton, thank you for your talk. Once upon a time - and this is not a fairy story - there was a cobbler who had two sons; one very bright who became a professor of mathematics; the other, dim, who became a millionaire shoemaker. Asked for the secret of his success, the millionaire attributed it to a vital piece of economics which his father had imparted, "Be content with small margins on a large turnover." "So", said the millionaire, "I make my shoes for $2 a pair and sell them for $5. I am very happy with the three per cent profit."

Jan 1, 1986

A new test coke oven of seven cubic foot capacity is described. The oven was designed to simulate conditions in a central section of a battery oven and a special feature is the achievement of unidirectional heating from the flues on either side of the charge. The method of charging permits close control of charge conditions'such as bulk density and moisture content. These conditions, as well as coking conditions (e.g. flue temper- atures., coking time) must be varied to simulate conditions in different batteries, The effects of several variables on coke quality are discussed. Using test oven conditions corresponding to those of Newcastle steelworks batteries, good agreement was obtained between strength indices of test oven and battery cokes; for 17 tests, the average A.S.T.M. stability and hardness indices for the test oven coke were 38,5% and 69.7%, while those for the battery coke were 37.1.% and 67.6%.

Jan 1, 1969