Search Documents

By F I. Cox, D Peeler, T Bodisco

"Diesel particulate matter (DPM), in particular, has been likened in a somewhat inflammatory manner to be the ‘next asbestos’.From the business change perspective, there are three areas holding the industry back from fully engaging with the issue:There is no real feedback loop in any operational sense to assess the impact of investment or application of controls to manage diesel emissions.DPM are getting ever smaller and more numerous, but there is no practical way of measuring them to regulate them in the field. Mass, the current basis of regulation, is becoming less and less relevant.Diesel emissions management is generally wholly viewed as a cost, yet there are significant areas of benefit available from good management.This paper discusses a feedback approach to address these three areas to move the industry forward. The six main areas of benefit from providing a feedback loop by continuously monitoring diesel emissions have been identified: Condition-based maintenance. Emissions change instantaneously if engine condition changes. Operator performance. An operator can use a lot more fuel for little incremental work output through poor technique or discipline. Vehicle utilisation. Operating hours achieved and ratios of idling to under power affect the proportion of emissions produced with no economic value. Fuel efficiency. This allows visibility into other contributing configuration and environmental factors for the vehicle. Emission rates. This allows scope to directly address the required ratio of ventilation to diesel emissions. Total carbon emissions. For National Greenhouse Emissions Reporting (NGER)-type reporting requirements, calculating the emissions individually from each vehicle rather than just reporting on fuel delivered to a site.CITATION:Cox, F I, Bodisco, T and Peeler, D, 2014. Continuous remote emissions monitoring – the lynchpin for air quality management, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 137–142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By D Kent, R Paine

"Automated mining systems are increasingly being seen as a key requirement for a productive mining operation in the future. The importance of an integrated communication network infrastructure to support such systems is growing.This paper outlines the introduction of automated mining systems in large conventional mines as well as their growing role in block cave mines currently operating or being developed. The paper will then focus on a case study of how the communication infrastructure is fundamental to the operation of such systems and explain why the resultant communication networks require much more than just increased bandwidth (data capacity) to properly support the automation system within the overall mine operation.Mining operations already embarking down this road are discovering that the required network must be based on a true enterprise level architecture to not only enable the mine’s current plans for remote and automated mining, but also provide a scalable and integrated platform for future developments and requirements. The emerging issues for the communication network to truly support automation systems include: increased complexities of operating and maintaining multiple networks integration issues with disparate systems problems with reporting particularly as demands for corporate reporting and compatibility with enterprise systems become the norm ongoing management challenges, which will only increase with the proliferation of new technologies.The paper will explore how certain mining operations are addressing this by adopting a long-term strategy for automation deployment, which includes laying the necessary foundation architecture to meet their current requirements, while supporting their future visions for the fully automated mine.CITATION:Paine, R and Kent, D, 2014. Developing the foundation communication infrastructure to support remote and automated mining initiatives in underground mines, in Proceedings 12th AusIMM Underground Operators’ Conference 2014, pp 151–158 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 24, 2014

By P de Caritat, A Davidson, A Mann

Top outlet sediments from the National Geochemical Survey of Australia have been extracted by a partial extraction method for over 50 elements including gold. The partial extraction results from this low-density survey show discrete coherent anomalies for Au in the vicinity of many of AustraliaÆs known goldfields, and in the vicinity of some minor gold occurrences. In several instances catchment outlet anomalies for Au have been recorded from areas not known to contain significant economic gold. Several large economic goldfields are shown to not produce anomalies in catchment outlet samples. A survey of overbank samples in the Swan Avon catchment of Western Australia at double the sampling density shows that low level anomalies (>1 ppb) can be traced back to source using overbank sediments. Follow-up of one of the Au anomalies at Kent River in previously regarded non-auriferous terrain (western Albany-Fraser Belt) indicates a non-economic, but perhaps geochemically significant, Au anomaly with associated pathfinders including palladium. This may indicate that further exploration of the western part of Albany Fraser Belt for Au is warranted. The combination of catchment overbank samples and partial analysis technique has been shown to be effective at locating the source of gold anomalies from initial low-density continental and regional surveys.CITATION:Mann, A, Davidson, A and de Caritat, P, 2013. High resolution soil geochemistry for gold exploration at the continental, regional and prospect scale, in Proceedings World Gold 2013 , pp 167-174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By F Weir, B Estrada

The impact of seismic loading on open pit slope stability in Australia is often only considered where the slopes are located adjacent to tailings facilities or other major infrastructure. The debate regarding application of seismic loading in open pit design in Australia is usually founded on limited reporting on significant damage of open pit operations during earthquakes, the common perception that earthquakes do not occur in Australia or that they are unlikely to occur during the mine life of the mine. It is frequently overlooked that pit slopes that have withstood strong earthquakes in highly active seismic regions are often designed under strict seismic guidelines. This paper discusses the factors that impact earthquake performance of open mine slopes. These factors include topography, slope geometry, rock material and mass properties, water management and intrinsic pit design. Further, the paper presents insights into the characteristics of earthquake activity in Australia such as magnitude distribution, earthquake depths, areas prone of earthquake activity and general seismic hazard that are relevant to pit design. Guidelines are provided on the conditions and circumstances under which earthquake design in open pit mining should be considered. In addition, this paper provides recommendation on the applicable methods for assessment of the impacts of earthquake loading on pit slope stability.

Jun 22, 2022

By A D. Campbell

The Homer Tunnel is located in a remote area of the South Island of New Zealand and carries large numbers of tourists to Milford Sound through an avalanche prone area. The tunnel is 1280 m long with a steep ten per cent unidirectional grade descending to the west. Construction of the tunnel began in the 1930s and was completed to a nominal 6 m width in 1954. In 1996, two passing bays were stripped-out to accommodate bi-directional flow of tourist coaches. During all phases of construction and widening there have been episodes of strain bursting.The condition of the tunnel and standard of internal services is below current international practice, principally in terms of; in-tunnel air quality, fire life safety, ground support, and road safety. A number of near-miss events have occurred involving coach fires on the approaches and inside the tunnel. The national road authority, NZTA, is considering a substantial investment to improve amenity and safety of the tunnel.This paper describes the rationale for the proposed upgrade works and the investigations undertaken to enable that design. A holistic approach to road tunnel safety has been adopted that balances the key interrelated safety drivers, namely; tunnel lining, traffic operations, ventilation, power supply and egress while ensuring continuity of safe access to Milford Sound.

Mar 8, 2011

By A Stasi, B Brice

Water is a limited and precious resource in Australia. Because of the increasing demand for water from all sectors of the economy and the variability in supply, efficient management of water resources is of vital importance. The national water reform agenda has provided a strong impetus to all states and territories to progressively move towards more efficient and sustainable water management. The Queensland Water Act 2000 is the legislative framework for providing water for the environment and for planning for the security of supply to water users. The comprehensive water planning process prescribed in the Act results in new tradeable water allocations that are separate from land. These water allocations are well specified and can be traded on a permanent or temporary basis. Trading of water allows it to move to its highest value use, thereby encouraging the most efficient distribution of this limited resource. In addition to transferring ownership of water allocations, it is also possible to change the attributes of the allocation, such as the location from which water may be taken. Changes to water allocations are subject to approval from the resource manager. Pre-testing allows for certain changes to be approved very quickly, making the trading process more streamlined and cost effective. Temporary trades, or seasonal water assignments, currently account for the majority of water trades in Queensland. However, permanent trading activity is expanding steadily as old water entitlements are converted to tradeable water allocations and as the market matures. The permanent trading market provides significant opportunities to the mining sector. It allows mining companies to buy water allocations at market prices without compromising environmental outcomes or causing third party impacts.

Jan 1, 2006

By W Midgley, M Torok, I Canbulat, J Katupitiya, S Saydam, S Akdag

The green energy transition is expected to require a range of valuable minerals, which could be supplied through deep-sea polymetallic nodule mining. Deep-sea polymetallic nodules are mineral deposits with a composition well suited to produce lithium batteries, which are expected to be a necessary energy storage solution (Diouf and Pode, 2015; Paulikas et al, 2020) for the energy transition. By 2050 the annual demand for both cobalt and lithium is estimated to increase by around 450 per cent from 2018 levels (Hund et al, 2023), with the annual demand for nickel being greater than 2 million tons, and copper greater than 1 million tons. Polymetallic nodule mining is well positioned to provide these minerals in the near future. An intricate and comparatively unexplored ecosystem thrives within and surrounding the nodule fields (Smith et al, 2008). Deep-sea mining operations have the potential to disrupt and permanently damage this ecosystem through introduced pollution, artificial noise and light, and habitat destruction. Hence, there is a pressing need for new engineering and scientific endeavours to focus on developing new technologies to reduce any environmental impact from mining.

Sep 1, 2024

By N McKay, J Vann, W Ware, P Hodkiewicz, C Morley

"Geometallurgy is now recognised within the mining industry as an approach that can both maximise value and reduce the risks associated with resource development. The process of spatial ore variability testing for metallurgical response and the use of quick, inexpensive metallurgical proxies has been well developed in the past decade in industry and the literature, and via various collaborative research programs and laboratories. Technology continues to advance with new techniques such as hand-held analytical tools and automated hyperspectral core scanning, allowing for even faster, less expensive in situ geometallurgical testing.In the current mining industry downturn, a critical frontier of geometallurgy is in its application in short-term geological modelling (ore control) and mine planning, and the associated decision-making. This is the end game at which the hard-won knowledge of orebody variability can be exploited to add near-term value. In order for spatial block models to be fit-for-purpose for such tactical uses, they must be populated with key geometallurgical information and then have workflows that use this richer model as a basis of material allocation to destinations so that the true value of the resource is realised.We envision geometallurgy (geomet) programs designed to add and sustain value at two levels:‘Strategic geomet’ has a long-term strategic focus that actively uses all relevant data that helps predict processing performance such as bench-scale metallurgical tests, mineralogy, geochemistry, ore texture etc (‘the geometallurgical database’) to model spatial ore variability and metallurgical response throughout the life-of-mine (LOM). This will enable better resource definition, more optimal mine planning and scheduling, improved process design and sustaining capital strategy over the LOM. The value-realisation is gained by basing all these strategic decisions on spatial models that better reflect the actual value of blocks (or aggregates of blocks) in the model.‘Tactical geomet’ has a short- to medium-term tactical focus that, again, actively uses the geometallurgical database, but also includes new data derived during ore control activities (such as drilling and sampling) to inform allocation-to-destination decisions via the ore control process. This will enable improved efficiency (ie less error) in allocation of mining blocks as direct feed, stockpile or waste. Importantly, this efficiency will be measured in terms of value and not grade, which is an incomplete – and typically biased – proxy for value. The key benefit is that ore control will then be planned and executed on the basis of realised value.We therefore propose a twofold systematic and holistic, value-based geometallurgical process. This process needs to be planned and implemented in an integrated manner, noting that strategic and tactical geometallurgy can be worked on by the same professionals, sharing data, methodologies and potentially models. What differs between the two levels is the required granularity, the business context and (critically) the decision-making time horizons.CITATION:McKay, N, Vann, J, Ware, W, Morley, C, Hodkiewicz, P, 2016. Strategic and Tactical Geometallurgy – a Systematic Process to Add and Sustain Resource Value, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 29–36 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D Reid

Characterisation of non-plastic segregating tailings presents a number of challenges: the material cannot typically be sampled in an undisturbed state, remoulded samples exhibit different behaviour to undisturbed samples, penetration test interpretation methods suffer from uncertainty in their application to many tailings and the tailings gradation changes considerably over relatively small lateral distances and depth. In addition, the process liquor of many Western Australian tailings contains large quantities of salt and other dissolved solids, which can further complicate laboratory test programs. To provide an insight into the variability at a typical gold tailings facility, four gradations of the material were tested to obtain critical state parameters. Historic surficial tube samples were collated and organised by gradation to establish the range of densities typical after settling and air drying. These were then compared to laboratory-accessible densities. Finally, tube samples were tested in the laboratory to observe if the large-strain material behaviour was consistent with the inferred critical state parameters for similar gradations. Site pore fluid was used in the testing of the tube samples in an attempt to assess if the pore fluid modified the critical state conditions of the material.The tube samples tested all exhibited strongly dilative behaviour in undrained shear. Of the four samples tested, only one exhibited behaviour consistent with the inferred location of the critical state line relevant to the material’s gradation. The reasons for the unexpected behaviour of the other three samples include layering within the samples, the potential influence of large quantities of salt in the pore fluid and likely differences in the gradation of the fines components of samples taken from mid-beach and the decant area.CITATION:Reid, D, 2015. Observations on the behaviour of a gold tailings with hypersaline pore fluid, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 191–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S Maritsa, E K. Chiw, S M. Masuka, ika, T Chisahwira

The challenges facing the iron and steel industry on a global scale include depletion of resources, excessive energy consumption and CO2 emissions. The demand for iron products in Zimbabwe is increasing due to massive infrastructural development like the expansion and improvement of mines, transportation systems and water reticulation systems. In Zimbabwe, cast iron is mainly produced from recycling scrap metals. However, there is currently a shortage of scrap, which has resulted in the vandalism of state-owned properties such as bus terminals and railway wagons and lines. Nevertheless, Zimbabwe is rich in limonite ores, which are idle, and it is the aim of this research that this ore be effectively used to produce feed for the blast furnace. The Blast furnace is still the dominant route for producing cast iron where sintering and coking processes are the main routes for preparing the Blast furnace feed. Sintering limonite ore fines produce a product of poor grade because of the high value of loss on ignition that has a negative impact on Blast furnace efficiency. Furthermore, the sinter plant and the coke making plant are a source of huge environmental pollutants. Since low-grade Zimbabwean coal fines are also available in abundance, they were used in the preparation of the composite materials ensuring maximum utilisation of this resource. Results showed that the limonite ore-carbon composite pellets sample with the binary basicity ratio (CaO/SiO2) of about 0.27 and coal addition of 2.5 wt per cent achieved above the minimum physical quality requirements for pellet of drop number of at least 4, a dry compression strength greater than 2.2 kg/pellet and an indurated compression strength greater than 250 kg/pellet. Limestone was used as the binder avoiding the addition of more impurities from bentonite since the limonite ore has a high SiO2 content of about 8.78 wt per cent.

Sep 18, 2023

By P G. Bourke, A Yáñez, G J. Jameson, N M. L Kupka

The kinetics of fine and ultrafine particles in conventional mechanical flotation cells are limited (Feng and Aldrich, 1999; Trahar, 1981; Wang et al, 2016). Accordingly, even limited recoveries with such machines require long residence times. Theoretical investigations into the rate of capture of fine particles by flotation, have indicated that a key parameter is the rate of shear in the fluid surrounding the bubbles and the particles. Achieving fast flotation rates of ultrafines requires a new method of bringing the particles and bubbles into contact, utilising the beneficial properties of highly dissipative flows to break through the water boundary layer. In 2010, a new type of flotation cell known as the Concorde Cell was described, in which bubbles and particles are brought together in a sonic shock wave (Jameson, 2010). Earlier research had shown that when a dispersion of fine bubbles in liquid passed through a converging nozzle at the local speed of sound, the resulting shock wave downstream generates a mass of even finer bubbles in the flow as it passes through the shock wave. The fluid within the shock wave is highly turbulent, and an environment is created that is very favourable to particle-bubble collision and capture. In this paper, we briefly describe the Concorde Flotation Cell and give examples of its use.

Aug 24, 2022

By K G. Harding, A Osman, A du Toit, F K. Crundwell, C M. Sheridan

"Most mineral processing plants have high water requirements for their operational activities. These plants often function in an environment where water is becoming increasingly scarce. An increase in population will result in an increased demand for water; potentially beyond the limits of supply and hence increased competition for the resource. In South Africa, Gauteng and the North West Province are likely to be first to experience a shortage of potable water.In order to avoid a water crisis, efforts must be made to ensure the effective management of water resources and the minimisation of wastage. Hydrometallurgical plants have a responsibility to society and the environment to operate in a sustainable manner - reducing their water requirements will certainly assist towards developing a sustainable footprint.This project improved site water management by: surveying the potable water and storm water systems with a view to assessing the current water accountability and determining methods to improve accountability determining the monthly and yearly water balance for the site and presenting it in the form of a water balance sheet drawing up an input-output and operational model in accordance with the Minerals Council of AustraliaÆs æWater Accounting Framework for the Minerals IndustryÆ calculating the water footprints of the refinery identifying ways in which water savings could be achieved recommending management systems for water usage monitoring.This work was conducted in South Africa. The value of this work lies in that it established the current baseline and assisted in developing management systems that can reduce water usage sustainably.CITATION:Osman, A, Crundwell, F K, Harding, K G, Sheridan, C M and du Toit, A, 2013. Water accountability and efficiency at a base metals refinery, in Proceedings Water in Mining 2013, pp 277-286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By T N. Little

The aim of any rock breaking activity is to achieve success by developing designs that are blasting objective-specific and geology-specific, and then implementing such designs. This paper targets mining geologists with the aim of extending their knowledge of the rock fragmentation processes and providing insights to the significant relationships between geology and blasting. There are two main relationships, and if mining geologists appreciate both these relationships, then they can play a key role in optimising production. The business risk continuum is introduced to support this understanding. The first relationship is between geology and potential blasting hazards, and the operational complexity required to manage those risks. The risks associated with eight different ground types are discussed in terms of ground conditions, hazards and controls. These types are: reactive ground, hot ground, geothermal ground, fibrous ground, cavernous ground, combustible ground, pyritic ground and conductive ground.The second relationship is between the bench geology and blasting results. The blasting results discussed include: muckpile characteristics, remaining rock faces and blasting emissions. In this regard, some detailed insights and graphical examples are given for the influence of geology on blasting emissions, in particular, vibration, airblast and flyrock.A detailed description of the geological materials themselves can convey much useful information for blasting operators provided they are able to utilise this knowledge. Geologists are ideally suited to provide this description more effectively if they are familiar with the blasting process and the rock mass properties that influence blasting hazards and blasting results. It is also important to have clear statements of blasting objectives and associated operational targets, and this will maximise the likelihood of achieving the desired outcomes. The main aim of the paper is to highlight that geology is currently not fully utilised in the blasting process. In this regard, geologists are often not entirely aware of the blasting process and how they can contribute. The two significant relationships discussed above are integral parts of this process, and thus they are discussed as separate issues in the main body of this investigation.

Aug 22, 2011

By G Corder

Even though most major operating companies in the minerals industry have Board-level endorsed sustainability principles and objectives, design engineers typically have no mechanism that allows them to implement those objectives in their work. In addition, the existing project management systems do not readily deliver the innovative solutions needed to address key sustainability issues, such as those related to significantly reduced carbon emissions, minimal environmental impacts, and maintaining the societal ‘licence to operate’. SUSOP® (SUStainable OPerations) is an approach for the integration of sustainable development principles into the design of mineral processes, which has been developed through the Co-operative Research Centre for Sustainable Resource Processing (CSRP). Somewhat analogous to the well entrenched HAZOP (Hazard and Operability) studies, SUSOP® is a holistic, systematic and rigorous mechanism for identifying and assessing sustainability opportunities and risks at each stage of project development - from corporate planning, through design and operation, to decommissioning and rehabilitation – without compromising financial rigour. SUSOP® was developed, tested and enhanced through its application to real case studies in the minerals industry. This development path provided significant insights into the process of identifying and evaluating opportunities for improving an operation’s contribution to sustainability and its long-term business case.This paper will discuss the need for a methodical approach for integrating sustainability principles into mineral processing plant design, present the key elements of SUSOP®, and outline its development path through real case studies. In addition, the reasons why such an approach will have growing importance into the future will be raised.

Aug 8, 2011

By T Baumgartl, D Bradshaw, B Forsyth, M Edraki

In a tailings storage facility, the chemistry of pore water is a function of oxidation and dissolution of sulfide minerals, containing metals and metalloids, the neutralising effect of gangue minerals and the geochemical processes controlling solute equilibria such as pH, redox potential, precipitation, ion exchange and adsorption. On the other hand, the changes in geochemical composition of tailings feed over time is a function of spatial variability within the orebody and modifications in processing method. Tailings properties such as pyrite content, pH, concentration of deleterious elements, surface chemistry, pore water chemistry and particle size are already shaped in the dynamic environment of a process plant.To engineer desired environmental outcomes, a new research framework is needed. The new approach should follow the physical and geochemical processes of tailings feed and construct models that can be used for the prediction of seepage water quality and dust propagation and evaluate the potential re-processing of tailings or production of tailings with desirable surface chemistry, particle size and internal structure. The challenge of developing tailings engineering model is not in laboratory techniques, but more of the overall communication of results and establishing the link between disciplines. It requires investigating geochemistry across mining and processing for improved environmental outcomes at tailings storage facilities.The paper reviews the current tailings management practices by comparing the geochemistry and mineralogy of tailings and the chemistry of seepage water from three Australian case studies in the context of geology, mineral processing and climate. Some alternative methods of tailings management are also reviewed and it is concluded that a proactive multi-disciplinary approach is needed with respect to tailings management, based on a novel integrated research framework.CITATION:Edraki, M, Forsyth, B, Baumgartl, T and Bradshaw, D, 2012. Geochemistry of tailings and seepage from three tailings storage facilities in Australia - Uncapped, capped and active tailings, in Proceedings Life-of-Mine 2012 , pp 269-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By A D. Campbell

Sublevel caving (SLC) is a mining method adopted in a wide range of mining depths and ground conditions with various layouts adopted to suit orebody geometry. Sublevel caving offers more flexibility and versatility compared to other cave mining methods and is a low cost alternative to open stoping. SLC also has the advantage that stopes are not required to remain stable during production, and no backfill is required. This flexibility combined with increasing pressure on mines to target deeper and lower grade mineralisation has led to increased uptake of the method. The implementation of SLC mining methods across a wide range of mining depths and rock mass conditions has led to ground control practices which vary globally from mine to mine. To date, there has been limited documentation of ground control practices in SLC mining and few benchmarks available in the literature. This paper describes the main findings from a global benchmark of sublevel cave mines conducted over three years as part of the Caving 2040 research consortium. The purpose of the project was to document and compare operational practices, technical aspects and hazard management techniques across SLC mines around the world. The review included 21 mines spread over four continents and 17 different mining companies. This paper provides an overview of geotechnical conditions, challenges and ground control practices at each of the benchmarked SLC mines. Mine design and sequencing practices adopted for ground control purposes and hazard mitigation are provided with case studies. The impact of depth and rock mass conditions on mining productivity and development rates is also described.

Nov 29, 2022

By S Johnston, L Howe, S Stevens

Regulators have an important role to play in fostering and enabling reliable, effective, environmental management. Given this, it is perhaps surprising that there has been relatively little debate on exactly how regulators can enhance their own approaches, in order to promote improved outcomes overall. The authors argue that applying research on High Reliability Organisations, as well as the University of Pennsylvania’s Penn Program Framework for Regulatory Excellence, to regulators has the potential to facilitate positive environmental results across the mine life cycle.

Aug 2, 2023

By J MacDiarmid

Atlas Copco is a leading provider of industrial productivity solutions (Atlas Copco, 2007) and one of the worldÆs largest suppliers of rock drilling equipment. The business division of Atlas Copco Construction and Mining Technique is based in +rebro, Sweden with the majority of their equipment produced in a number of facilities within the area. As part of the 2006 AusIMM/Atlas Copco Scholarship I was fortunate enough to visit these facilities to experience first hand this truly unique global company. Through numerous presentations on the various divisions and products manufactured by the company, I saw the broad range of products and services offered by the company and came to realise it is much more than just selling drills. Other highlights included a brief love affair, a tour of EuropeÆs largest underground mine (or factory depending who you ask), a drink at the ice bar at the ice hotel in JukkasjSrvi, and a number of dinners of reindeer. Overall this it was a truly amazing experience with all involved with the program going out of their way to ensure I got the most out of the trip. More importantly, through no effort at all, everyone naturally conveyed their passion for the industry and the company which is a great credit to the æAtlas Copco WayÆ thereby creating a company æcommitted to your superior productivity through interaction and innovationÆ.

Jan 1, 2007

By M Fishwick Tapia

This paper was prepared and translated from the final report of the investigation into the Codelco Chile Salvador DivisionÆs air blast which occurred in the Inca-West area. In this section of the block cave mine, a stable arch formed covering an area of approximately 15 000 m2 . This zone subsequently collapsed producing a massive air blast. The collapse followed a series of planned extraction activities and occurred on 5 December 1999. This paper discusses the cave back arching event and the measures that were taken in order to induce the controlled collapse. This was to minimise risk to personnel, equipment and installations. The results obtained to date are presented.

Jan 1, 2000

By B N. Noller, J C. Ng, S L. Bruce

Mining activities can result in the transfer of harmful elements, including arsenic and lead, into the environment. In Australia, one of the potential future uses of rehabilitated mine land is to stock grazing animals. Elemental uptake is dependent on bioavailable fraction for adsorption upon exposure. Bioavailability data are generally lacking in order to provide realistic health risk assessments relating to harmful elements from mine tailings in Australian conditions. Another key component of risk assessment is the ability to estimate a realistic exposure, or dose rate, of the tailings to the grazing cattle over a set period of time. Hence, we aimed to conduct grazing trials directly on rehabilitated tailings facilities in order to provide valuable in situ information on heavy metal dose rates and associated accumulation. For the laboratory-based evaluation of comparative bioavailability, groups of cattle were fed five days a week on a normal diet spiked with mine tailings or soluble pure salts of target elements (eg sodium arsenate, sodium arsenite and lead acetate) for about eight months. For the field validation, cattle were allowed to graze directly on rehabilitated tailings facilities over a similar length of time. Blood and a biopsy of the muscle and liver were periodically collected to monitor arsenic accumulation. At necropsy, blood, muscle, liver, kidney and other saleable tissues were measured for arsenic concentrations. Although this study was focused on arsenic, lead and other metals were also measured. Predictive models for arsenic and other metals have been established to calculate the maximum grazing duration without the risk of exceeding specific food safety guidelines. The outcome of this study is a predictive model for maximum beneficial use of certain rehabilitated tailings for cattle grazing where grazing activities do not impact on the integrity of the tailings dams.CITATION:Ng, J C, Noller, B N and Bruce, S L, 2014. A predictive model for beneficial use of rehabilitated mine tailings for grazing cattle after mine closure, in Proceedings Life-of-Mine 2014 , pp 563–572 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014