Search Documents

By Thomas M. Drown

I DESIRE to communicate to the Institute the results of a few analyses which bear on the condition of carbon in gray and white iron. These analyses were made in the course of an investigation, now in progress, of the chemical composition of "chilling" irons. It will be remembered that Bell says he found no material difference in the amount and condition of carbon in gray and white pig iron made at the Clarence furnace, in England, and he therefore refers the difference in color and appearance in these two varieties of iron to the size of the particles of graphite. I quote from his "Chemical Phenomena of Iron Smelting:" "The inference I would draw from the information afforded by these analyses is, that the condition of iron in respect to its so-called 'richness' is, within certain limits, entirely independent of its chemical constitution.. .. In the fluid state, I conceive the carbon, so taken up, confers upon the iron the property of fusion much below the temperature at which the pure metal melts, and the carbon itself may be regarded as dissolved in the iron. If, during the process of manufacture, the pig metal has been formed at a low temperature, consolidation, I imagine, takes place under such circumstances that the crystals are so minute, and the carbon which is separated assumes the uncombined or graphitic form in particles so minute as to be invisible, and, in consequence, the iron is white. If, on the other hand, the furnace is working at a very high temperature, the intensely heated iron crystallizes with large facets, upon which the extruded carbon assumes the condition of distinct plates or flakes. Should the temperature be less intense, these crystals are of smaller dimensions, and the separated carbon is less conspicuous, and, as the temperature of the furnace declines, the crystals decrease in size, as do the flakes of carbon, until both disappear in white iron.. .. Returning, then, to temperature as the cause of differences in quality of pig iron, the 'chilling' of gray metal, and its conversion into white, may be regarded as the effect of preventing, by rapid cooling, the formation

By Ralph Arnold

THOUGH production began in Canada only a short time after the discovery of oil in the United States, it has never attained large proportions, and if we were to judge entirely by the past the reserves of Canada would be put at a very low figure. There are only two areas from which oil is marketed at the present time; one, the old district around Petrolia in southern Ontario, and the other is the small Sheep Creek field near Calgary in Alberta. The former district has produced between 200,000 and 800,000 bbl. annually for the past 40 years, recent figures being near the minimum amount. Sheep Creek has produced about 12,000 bbl. annually for the past five years. The known reserves in proved territory in each of these fields are exceedingly small, when considered in terms of world reserves. The chief hope of Canada for reserves of considerable magnitude lies in the western provinces. Sedimentary rocks similar to those in the productive fields of the United States occupy thousands of square miles in the western provinces, so that it seems likely that somewhere within this great area the peculiar conditions necessary for the presence of oil pools will be found. Prospecting is being carried on energetically by several large companies, as well as by many independents. The Dominion Government, which controls most of the public lands, is pursuing a .fairly liberal policy toward the prospector, which should stimulate wildcatting; although the province of British Columbia, which controls public lands within that province, is at present unwilling to give adequate encouragement to make wildcatting attractive. As there is really no assurance that any productive pools will be found in western Canada, the estimates of reserves are subject to a wide possibility of error. In making estimates, the various areas within which geologic conditions are more or less uniform are discussed separately; the estimates given for each area are not given with the idea that there is a reasonable probability of their eventually proving to be correct. It is hoped that an average of these estimates, taken together with those made for other undeveloped countries, will give a correct total of reserves

Jan 7, 1922

THE Rocky MountainClub brought into the East the spirit of the West; the impulse to build, to develop, to accept unquestion-ingly the comradeship and help of any straight shooter who had it in him to accom-plish things and a will to work. That this was the spirit of the Club was due to its leaders. It was their spirit and they attracted around them men of the same stamp. Among those who made the Club what it was no one had larger in-low fluence than William Boyce Thompson, the vice-president and chief of financial staff. It was characteristic of him that the same financial genius that was employed in building up Nevada Consolidated, In-spiration, Magma, Texas Gulf, and as director of the Metro-politan Life and the Federal Reserve Bank, was freely placed at the service of the Club. It was equally char- acteristic that the generosity that financed the Red Cross Mission to Russia inspired the use of the Club funds for Belgian and war relief. "W. B.," as he is known to his many friends, was born at Virginia City in Alder Gulch, Mont., on May 13, 1869. His father, William Thompson, born at Cobourg, Ont., had drifted into the old Northwest and, hearing at Yankton of the gold strike at Bannack, crossed the plains on the Oregon trail in the summer of 1863, arriv-ing in Alder Gulch at the inception of a mining boom that lasted several years, during which something like $60,000,000 in gold was yielded by the placer diggings. His mother was a daughter of Maj. James R. Boyce, Sr., from Logan County, Ky., who had served under General Sterling Price of the Confederate Army. Major Boyce's ancestors were early settlers of the Old Dominion, and his grandfather had seen military service in the war for American independence. Major Boyce's mother was a descendant of the Marshall and Smith families of Westmoreland County, Va. When Thompson was eleven years old, the family moved to Butte, then a silver camp. He attended the public schools of Butte, but desiring a better education, entered Phillips Exeter Academy and later the Colum-bia School of Mines. Returning West, for a year or two he ran the Boulder Chief mine near Basin, Mont., which earned him a sobriquet, "Boulder Thompson." While here, some old ore sacks, oil-soaked, introduced him to flotation. He was also the first to leach some of the ore dumps of Butte.

Jan 4, 1928

By P. Niessen, S. J. Bercovici

RECENTLY Aust et al.&apos; proposed a model of non-equilibrium grain boundary segregation based on a vacancy gradient induced uphill diffusion process of solute to grain boundaries. According to their proposal, solute atoms which are attracted to vacancies would, during the cooling of a sample, migrate with vacancies toward grain boundaries (vacancy sinks) and thereby enhance the solute concentration in boundary regions. For solute atoms which are not attracted to vacancies no such boundary solute enrichment would be expected. These concepts were given experimental support by boundary and bulk mi-crohardness measurements of various thermally treated dilute zinc and lead alloys and also doped aluminum oxide. The underlying assumption in their work was that solute enrichment in boundary regions is indicated by higher microhardness values. From thermodynamic considerations1&apos;2 it appears that the solid-liquid solute distribution coefficient (K), defined as the concentration of solute in the solid to the concentration of solute in the liquid at equilibrium, indicates whether attractive or repulsive forces exist between vacancies and solute atoms. K < 1 indicates a solute-vacancy attractions, K > 1 indicates no, or a repulsive, vacancy-solute interaction. This note is to report on observations of different grain boundary etching phenomena in high purity zinc alloys. These phenomena appear to depend on whether a K < 1 or K > 1 solute is present. In experiments designed to measure directly the solute enrichment in grain boundary regions, samples of zone refined zinc with 0.1 at. pct solute additions were cooled from 380°C at a rate of 3°C per min. A surface layer of approximately 50 was then removed from the samples by chemical polishing. The samples&apos; surfaces were then protected by a chromating treatment such that in a subsequent etch only grain boundary regions were dissolved. The dissolved regions were approximately semicircular troughs, 10 µ in width. The grain boundaries were usually in the middle, i.e., at the bottom, of this trough. For zinc containing the K < 1 solutes cadmium and aluminum, the grain boundary was always indicated by a ridge as shown in Fig. 1. For pure zinc, and zinc containing the K > 1 solutes copper and gold, a groove at the bottom of the trough indicated the boundary position, Fig. 2., To test if these different grain boundary etching behaviors were possibly connected with the segregation process discussed above, the Zn-Cd alloy was again heated to 380°C and quenched into brine. After surface protection and etching it was found that this specimen no longer exhibited the grain boundary ridges but rather grain boundary grooves as shown in Fig. 2. It would appear, therefore, that the boundary ridge is a consequence of a process occurring during the slow cooling of the samples. From absorption spectrophotometric analysis it was found that for slowly cooled samples containing K < 1 solutes, the solute/zinc ratios of the material from the boundary trough were consistently considerably higher than the solute/zinc ratios of the bulk alloys. This boundary region solute enrichment was not observed in quenched samples. It is concluded therefore, that the boundary ridge shown in Fig. 1 is directly or indirectly connected with nonequilibrium solute segregation.

Jan 1, 1970

"WELFARE…Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years and both the operators and their employees are deserving of much credit for the efforts put forth to better living, working, educational and receational conditions in most of the mining camps of the state.In the older metal mining camps of Utah, where the towns are incorporated and independent of the mining properties operating in the vicinity, less opportunity is pre¬sented for the companies to exercise efforts looking towards improved welfare conditions than is the case of camps located on company ground and under the full control of operators.Even in such camps, however, as illustrated in Bingham, the companies can do much to better welfare conditions. In this camp the Utah Copper Company has spent $800,000 since 1 920 in the erection of modern brick cottages, apartment houses and the Gemmell Memorial Club. The cottages and apartments have every convenience to be found in up-to-date city homes. The Gemmell Memorial Club, erected and equipped at a cost of $1 75,000, was provided by the company for the benefit of the Utah Copper Company employees living in the canyon and has been made the recreational center for the camp."

Jan 1, 1925

By J. Lindbo, B. Vigeholm

IN transmission electron microscopy, specimen thicknesses quoted are frequently based upon either traditionally familiar values or a few evaluations representing the whole material. Taking aluminum in 100 kv TEM as an example, average and maximum values are widely accepted as being 2000 to 2500 and 6000 to 7OOOÅ, respectively. It is the purpose of this note to revise these figures and to point out the importance of evaluating individual specimens carefully. All evaluations have been based upon slip trace widths and lattice orientations as determined from diffraction patterns. In many cases where two or more slip systems have been operating the geometrical method described by Crocker and Bevis1 has been applied as a check. The foils were usually oriented to within 2 deg from the exact Bragg angle. Kikuchi patterns were used as indications of correct orientations but not applied in the evaluations. The tilt of the foil surface relative to the beam normal may with certain geometrical relations between the tilt axis and the operating slip plane lead to substantial errors.2&apos;3 Where these geometries were inevitable the samples were omitted in the investigations. Various measures were taken in order to overcome ambiguities, e.g., comparison with neighboring grains, tilts, evaluations based upon two or three slip systems,&apos; and comparison with extinction contour evaluations where s = 0 conditions were obtained. Errors caused by misinterpretation of the slip traces on a micrograph are easily avoided by considering the bright-dark sequence on opposite surfaces and by taking into account the tapering of the foil usually leading to a distinguishable divergence of the pair of traces. In the investigations described here the interpretation was further facilitated as the slip trace formation was observed on the microscope screen and sketches taken down. In a few observations slipping was so violent that the distinction of pairs was considered dubious and consequently given up. To assess average values, thickness evaluations carried out in two independent investigations were analyzed: I) 99.998 pct A1 extruded, cold-drawn, and recrys-tallized to grain sizes between 35 and 500 um were deformed in tension at room temperature. In order to determine the dislocation densities as a function of strain,4 specimens prepared by spark machining and electropolishing in a PTFE holder were analyzed in the electron microscope at 100 kv. Thicknesses were evaluated for 569 selected areas. Histogram I in Fig. 1 shows the results, the average thickness being 4900Å. II) Electropolished specimens prepared from 99.9999 pct A1 with magnesium contents from 0.005 to 0.5 pct rolled to foil and annealed were subjected to fission fragment irradiationa2 For volumetric dose and defect concentration determinations thickness evaluations were performed on 123 areas. Histogram II in Fig. 1 shows the thicknesses of these areas averaging 4250Å. Whereas in investigation I no selection related to thickness has been made, some thin as well as thick areas have been omitted from I1 for experimental reasons. This and the application of two different microscopes although of the same type may account for the difference in average thickness. Assuming a mean error of 10 pct for a single evaluation, the error of the average should be negligible. In order to investigate the maximum transmissible foil thickness in aluminum, specimens were prepared from single crystals with (111) and (110) orientations parallel to the beam, and from polycrystalline material. Maximum values of thickness that could be measured were given by the stopping of the dislocations. The visibility often extended far beyond the end of the slip trace, but with no means of knowing the

Jan 1, 1970

Jan 1, 1934

Jan 1, 1947

Jan 1, 1934

Map

Jan 1, 1952

Jan 1, 1902

Jan 1, 1883

New Products Equipment

Jan 8, 1951

Jan 1, 1920

By Jack Washburn, E. R. Parker

Kinking in zinc single-crystal tension specimens was observed under conditions of low stress and high temperature. Kinking is discussed in relation to other plastic bending phenomena on the basis of dislocation theory. Experiments on the stress-induced motion of small angle boundaries are reported. KINKING was first reported by Orowan1 as a new deformation mechanism. He observed the phenomenon in cadmium single crystals loaded in compression. Glide lamellae in a local region of the rod were observed to snap over suddenly to a tilted position, resulting in a sudden shortening of the specimen. Between the tilted portion and the rest of the crystal there were fairly sharp boundaries, with the slip plane assuming approximately mirror image positions on opposite sides of these boundaries. Orowan considered the boundaries to be regions where dislocations had concentrated. Hess and Barrett&apos; observed the formation of kinks in critically oriented zinc compression specimens. It was found that the sudden snapping over of the tilted region was not an essential part of the kinking phenomenon but rather was associated with the method of loading. Kinking was explained on the basis of the accepted mechanisms of slip and flexural glide. It was also suggested that a kink can be considered as a special type of deformation band. During a recent investigation of the effect of surface condition on creep of zinc single crystals," a similar phenomenon was observed in crystals which were loaded in tension. The specimens were 0.4 in. diam cylindrical rods with a free length of 4 in. between end connections. All of the crystals were tested at a constant load. adjusted to give an extension rate of approximately 0.05 pct per hr. Kinking, as shown in Fig. 1, occurred in some of the tests performed at temperatures above 200°C. Kinking was observed in specimens varying widely in initial orientation, scattering about a 45" angle between the slip plane and the specimen axis. The condition leading to kinking in tension appeared to be non-uniform distribution of flow along the gage length combined with the restraint imposed by the tensile load. At low temperatures and fast strain rates, the distribution of strain throughout the midsection of tension specimens was generally quite uniform; therefore, bend planes developed only near the ends as described by Miller.4 However, at high temperatures under creep conditions it was difficult to obtain specimens in which the distribution of flow was uniform. Some of the factors which may have caused differences in flow stress along the length of the crystals are: Nonuniform distribution of impurities, accidents of growth (lineage structure), slight bending or other damage during handling, surface conditions, and strain-aging characteristics due to dissolved nitrogen." Plastic flow, once started in a local region, often continued to a relatively large strain before other parts of the gage length became active. Under these conditions a series of kinks, such as those in Fig. 1, were produced. Fig. 2 illustrates how a nonuniform distribution of slip produces bending moments which- are responsible for kink formation. If no plastic bending were to occur while the rod extended by pure slip in two separate sections of the rod, it would assume a shape such as that in Fig. 2a. A specimen having this shape and being subjected to a tension load would have concentrations of stress at the concave surfaces C and lower than average stress would exist at the convex surfaces D. Therefore a bending moment is superimposed on the average stress in the regions between C and D. The positions of potential bend planes under these conditions are shown as dotted lines. Actually no such shape as Fig. 2a develops because plastic bending in the region C-D occurs simultaneously with pure slip in the intervening regions. The observed structure of a tension kink is indicated by Fig. 2b. Perhaps the best approach to an understanding of kinking as well as other related plastic bending phenomena, such as the bend planes discussed by Miller,&apos; cell formation studied by Wood et al.,6 and polygonization,7 is consideration of the dislocation model of a bent lattice. Current theories of the slip process postulate generation or multiplication of dislocations at certain lattice imperfections. The mechanism proposed by Frank and Read8 results in continuous generation of concentric dislocation loops which spread out

Jan 1, 1953

PRESIDENT. CHARLES F. RAND,1 NEW YORK, N. Y. PAST PRESIDENTS. CHARLES KIRCHHOFF,1 NEW YORK, N. Y. JAMES F. KEMP,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT. BENJAMIN B. THAYER,1 NEW YORK, N. Y. TREASURER. GEORGE C. STONE,&apos; NEW YORK, N. Y. SECRETARY EMERITUS. ROSSITER W. RAYMOND NEW YORK, N. Y. SECRETARY. BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 11, 1913

In preparation for the 118th meeting, New York, Feb. 17 to 20, 1919, the following committees have been appointed: Committee on Arrangements ALLEN H. ROGERS, Chairman. W. S. DICKSON, Secretary. J. E. JOHNSON, JR. F. T. RUBIDGE. H. C. PARMELEE. FOREST RUTHERFORD., P. G. SPILSBURY. Committee on Annual Dinner Committee on Luncheon F. T. RUBIDGE FOREST RUTHERFORD, Chairman. E. B. STURGIS. E. MALTBY SHIPP. Committee on Patriotic Meeting H. C. PARMELEE, Chairman

Jan 9, 1918

Mining headlines in 1952 dealt mainly with expansion as the industry aimed for an ever increasing production to meet the nation&apos;s needs. Huge sums were expended for equipment, research, and development. Headlines told part of the story. Negotiations between San Manuel Copper Co. and the RFC finally resolved in a $94 million loan for the development of low grade Arizona ores. Magma Copper, parent firm was to supply an additional 8 million. Kennecott Copper Co., deepening its Deep Ruth Shaft of its Ruth, Neyy mine, announced that the shaft would be in full production in 1953.

Jan 2, 1953

YEAR OF ELECTION 1913. FRANK DAWSON ADAMS, Montreal, Canada. 1933. KARL EIKERS New York, N. Y. 1922. FEDERICO GIOLITTI Torino, Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1941. DANIEL COWAN JACKLING San Francisco, Calif. 1939. HENRY KRUMB New York, N. Y. 1921. C. McDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1935. ROBERT PEELE New York, N. Y. 1938. A.M. PORTEVIN Paris France 1937. JOHN V.W. REYNDERS, New York, N. Y. 1937. GEORGE S. RICE Washington, D. C. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T.A. RICKARD Victoria, B.C., Canada

Jan 1, 1941