Search Documents

By K. M. Weigert

The position of the three-phase field between the alpha and the beta phases was established. The exact location differs from previous assumptions. The extremely high strength and hardness values were found near the phase boundaries of the ternary compositions. IN 1929, UenoL investigated vertical sections of the Ag-Cu-Zn diagram at constant silver and zinc values. From the evaluation of cooling curves and microscopic studies, he concluded that there was no evidence of a three-phase field in the solid state between the a and ,8 fields. The failure to find evidence for this field was due to the fact that it exists only in a very narrow range of compositions and requires special methods of heat treatment to establish phase equilibrium. In a later publication on the same subject Keinert2 rearranged Ueno's diagrams to conform with the basic phase rules. The existence of a three-phase field was postulated in the solid state between the a phases and the homogeneous ,9 phase between the Cu-Zn and the Ag-Zn binary border systems. The approximate location was based on a few microscopic observations of the structure and it was pointed out that the exact position could be determined only by a larger number of experiments. In the twenty years following these investigations alloys of Ag-Cu-Zn have become of general interest due to various technical applications, principally for brazing. In the course of an overall investigation of the physical properties of ternary Ag-Cu-Zn alloys the author found extremely high values of hardness and strength in alloys of compositions between the a and the yS fields. The exact location of the intermediate phase fields was established by the evaluation of more than a hundred cooling curves and microscopic mountings. Experimental Procedures Preparation of Test Samples: At the beginning of the investigation samples were chillcast into Vi in. diameter iron molds to determine hardness, strength, and the mechanism of primary crystallization. These

Jan 1, 1955

By Charles E. Locke

DEPRESSION in all lines of the mineral industry except gold, which began in 1930 and continued, even worse, through 1931, had its effect on ore concentration. Construction was limited to the completion of plants already begun. Every possible economy was adopted. Changes and improvements involving expense were postponed. Research was largely abandoned. Operations became highly efficient and costs were cut down, although this did not necessarily mean a lower cost per ton because of the greatly reduced capacity at which mills were run. Lower metal prices caused the operators to seek the optimum ratio of concentration and grade of concentrates looking toward maximum economic recovery; that is, net profit. In the crushing field no marked changes occurred. The Symons cone crusher for intermediate work is in use almost everywhere. Its manufacturers claim that 900 machines have been installed in 21 countries, replacing two previous steps of crushing and yielding a product sufficiently fine to form a satisfactory feed for rod mills and ball mills. A new Telsmith crusher has appeared which has curved jaws something like the Symons cone and consequently the same advantage as the latter.

Jan 1, 1932

By Gerald Sherman

MINE fires are always dangerous and are frequently accompanied by loss of life during the period of confusion which is apt to follow their discovery. In metal mines, fires may result from the accidental ignition of some combustible material, or they may be of spontaneous origin resulting from the rapid decomposition of sulphide. They occur frequently enough to demonstrate the need of some special equipment and a general plan for controlling them, in addition to measures for their prevention. Nearly all the large copper mines have had fires, and the methods of fighting them have been well described in recent papers, notably-by C. L. Berrien,1 R.. E. Tally,2 and others in discussion. The Copper Queen mine has many shafts, which are connected by underground workings. The deeper parts are ventilated by fans, but in the shallower portions natural ventilation through numerous connecting raises or shafts is sufficient. There have been several fires in the past few years, of which all are extinguished but one, and that is under control. These notes cover particularly the preparations that are being made-to check a new fire, partially or temporarily, and to facilitate the escape of workmen in the interval before a definite plan of fighting it can be established. A fire may occur in a shaft or station, or in some working father away. In case of fire in an upcast shaft, the gas would escape to the surface and the immediate result would probably not be dangerous to workmen, as they could escape by other shafts. In a downcast shaft, however, the gas would be distributed very rapidly throughout a large portion of the mine, and men might easily be trapped and asphyxiated. A fire in mine workings, drift, raise, or stope, would be dangerous in a degree, but the draft there is likely to be less strong than in a shaft and probably a smaller area would be invaded by the fire gases.

Jan 1, 1918

By John T. Norton

FoR many years the copper-bearing steels have been of considerable interest to the metallurgist because of their corrosion-resistant properties. More recently the discovery of their definite age-hardening characteristics has focused attention on them again. In a recent paper, Smith and Palmer(l)† have given an admirable description of the behavior of a considerable number of steels of this type and a study of their results suggests two questions of a more or less fundamental sort. In the first place, it has been plainly shown that the hardening effect of added copper does not increase up to the maximum solubility of copper in iron as given by earlier investigators, but reaches its greatest value considerably below this point. This fact suggests that either the solubility is not so great as previous investigators have stated, or that the age-hardening mechanism is not the simple precipitation phenomenon that has been postulated. In the second place, the nature of the aging mechanism in this particular system should be determined. Recent developments in the study of age-hardening processes have shown that the increase of hardness is often, but not always, accompanied by precipitation and the action of a particular system is not predictable on the basis of its components or type of phase diagram. It would be of considerable interest to study the aging of the iron-rich iron-copper alloys in detail. One would like to know whether the aging mechanism is different at high and low aging temperatures, and whether the extreme sluggishness of the system may perhaps represent some new type of aging process. The experiments to be described were carried out in an endeavor to answer these questions. Obviously, in such experiments it is important to confine the hardening effect to the single element, copper, so that iron and copper of high purity must be used in the preparation of specimens. An observation of lattice changes during the aging process, correlated with the hardness changes, seems to be the best available method of

Jan 1, 1935

By John T. Norton

FoR many years the copper-bearing steels have been of considerable interest to the metallurgist because of their corrosion-resistant properties. More recently the discovery of their definite age-hardening characteristics has focused attention on them again. In a recent paper, Smith and Palmer(l)† have given an admirable description of the behavior of a considerable number of steels of this type and a study of their results suggests two questions of a more or less fundamental sort. In the first place, it has been plainly shown that the hardening effect of added copper does not increase up to the maximum solubility of copper in iron as given by earlier investigators, but reaches its greatest value considerably below this point. This fact suggests that either the solubility is not so great as previous investigators have stated, or that the age-hardening mechanism is not the simple precipitation phenomenon that has been postulated. In the second place, the nature of the aging mechanism in this particular system should be determined. Recent developments in the study of age-hardening processes have shown that the increase of hardness is often, but not always, accompanied by precipitation and the action of a particular system is not predictable on the basis of its components or type of phase diagram. It would be of considerable interest to study the aging of the iron-rich iron-copper alloys in detail. One would like to know whether the aging mechanism is different at high and low aging temperatures, and whether the extreme sluggishness of the system may perhaps represent some new type of aging process. The experiments to be described were carried out in an endeavor to answer these questions. Obviously, in such experiments it is important to confine the hardening effect to the single element, copper, so that iron and copper of high purity must be used in the preparation of specimens. An observation of lattice changes during the aging process, correlated with the hardness changes, seems to be the best available method of

Jan 1, 1935

By R. W. Young, Arthur F. Taggart

The tests herein described are part of an extended series of expel<ments, performed by the authors together with J. F. McClelland and L. W. Bahney, on the reclamation of metallics from foundry and manufacturing-plant scrap. The most obstinate problem encountered was the proper cleaning of the metal. Introduction In the manufacture of brass and brass products the weight of the finished product leaving the plant is much less than the total weight of. copper and zinc entering. A small part of this discrepancy is due to the unavoidable oxidation of the metals in melting, but by far the largest part of the loss is in the form of metallic particles of copper,. zinc, and brass. These losses occur principally at three points in the process: (a) in the casting-shop ashes; (b) in the slags from furnaces melting scrap brass; (c) in material spilled on the floor throughout the manufacturing process. The amount of these products in some plants is nearly 100 tons per 24 hours. Casting-shop ashes contain the metal spilled from the crucibles during melting and pouring, and the metal included in the slags formed in the melting process. The ashes also contain pieces of broken crucibles with adhering metal; 20 to 30 per cent. of unburned coal is also present. The metal in casting-shop ashes contains clean pieces of zinc or copper ingots weighing 1 to 2 lb., jagged pieces of metal of all shapes ranging in size from several inches down to the finest dust, and shot and botryoidal shapes ranging in size from 2 or 3 in. down to 0.01 mm. or less in diameter. Slags from furnaces melting scrap brass contain metal in the form of small shot. Floor sweepings occur in all shapes: spirals, thin shavings, pins and pin-like pieces, wire, rods, and buffing-wheel dust are the commonest.

Jan 1, 1916

By G. Czupryna, S. Natansohn

Electrowinning is the prevalent technique for recovering silver from wastes generated in silver-tungsten electrical contact fabrication. Such scrap is placed in a permeable plastic basket, which constitutes the anode compartment, and is suspended in a larger cell where the cathode is mounted. A silver nitrate solution is used as the electrolyte and, upon application of an electric field, the silver migrates to the cathode where it deposits. At times, there is tungsten migration to the cathode compartment and consequent co-deposition with the silver. This W contamination, which may amount to several thousand mg/L (oz per gal), necessitates additional purification of the deposited Ag and its removal would, therefore, be advantageous. Eliminating the W impurity also extends the operating period of the cell with corresponding increases in the Ag output and savings in labor costs. The solution to this problem lies in the selective removal of the W from the AgNO3 electrolyte either by liquid-liquid or liquid-solid extraction. Although W extraction in the liquid-liquid mode with a quaternary amine or other reagents as extractants appears feasible, particularly in view of the low pH (about 1.5) of the system, this approach was not considered because it is essentially a batch-type process. It is a more elaborate industrial operation than extraction by ion exchange resins. Implementing the latter process consists of passing the electrolyte from the electrowinning cell through an ion exchange column which would extract the tungsten selectively and returning the tungsten-free stream to the cathode compartment. This process continues until the W extraction efficiency decreases (as a result of resin loading) below an acceptable value. The electrolyte is then directed through another, similar column while the W values are eluted off the first one and the resin is regenerated for another cycle. Thus, two columns in a parallel flow pattern provide the means for continuous processing of the electrolyte feedstock.

Jan 1, 1984

By B. B. Zavoico, J. G. H. Crump, P. P. Gregory

West Texas was the scene of greatly increased oil activity during 1937, producing 75,743,000 bb1.l in that year as compared with 61,901,-000 bb1.2 in 1936, an increase of 22.36 per cent. The annual total of wells completed increased from 15863 in 1936 to 28062 in 1937, an increase of 76.92 per cent. Of the total completions in 1937, 2464 were oil wells,2 11 gas wells2 and 331 dry holes.2 The marked increase in the number of oil wells completed in West Texas during 1937 had a substantial effect upon the daily average production per well, which decreased 20.84 per cent from December 1936, when a total of 5310 wells3 produced 5,236,467 bbl.3 for an average of 31.81 bbl. per well per day to December 1937, when 7571 wells2 with a total production of 5,910,257 bb1.2 averaged 25.18 bbl. per well per day. Drilling blocks and checkerboard acreage were being acquired following geophysical work in the northern end of the Permian Basin area, composed of Bailey, Cochran, Hockley, Yoakum and Terry Counties, presaging extension of active development northward. During 1937, at one time 30 geophysical crews were working in West Texas, and an average of 15 to 20 crews was active in this area throughout the year. Discoveries Wasson-Denver Field.—Wasson-Denver field in Gaines and Yoakum Counties was the outstanding field discovery of the year. Production is from porous limestone found at about 5000 ft., and an average well is good for from 300 to 500 bbl. of crude oil per day through 3/4-in. choke. The discovery well was drilled by A. G. Carter and others on the Wasson Ranch, Gaines County, and the field has since been extended into Yoakum County. At the year&apos;s end 21 wells had been completed, producing

Jan 1, 1938

By Gerald Sherman

Mine fires are always dangerous and are frequently accompanied by loss of life during the period of confusion which is apt to follow their discovery. In metal mines, fires may result from the accidental ignition of combustible material, or they may be of spontaneous origin resulting from the rapid decomposition of sulphide. They occur frequently enough to demonstrate the need of some special equipment and a general plan for controlling them, in addition to measures for their prevention. Nearly all the large copper mines have had fires, and the methods of fighting them have been well described in recent papers, notably by C. L. Berrien,1 R. E. Tally,2 and others in discussion. The Copper Queen mine has many shafts, which are connected by underground workings. The deeper parts are ventilated by fans, but in the shallower portions natural ventilation through numerous connecting raises or shafts is sufficient. There have been several fires in the past few years, of which all are extinguished but one, which is under control. These notes cover particularly the preparations that are being made to check a new fire, partially or temporarily, and to facilitate the escape of workmen in the interval before a definite plan of fighting it can be established. A fire may occur in a shaft or station, or in some working farther away. In case of fire in an upcast shaft, the gas would escape to the surface and the immediate result would probably not be dangerous to workmen, as they could escape by other shafts. In a downcast shaft, however, the gas would be distributed very rapidly throughout a large portion of the mine, and men might easily be trapped and asphyxiated. A fire in mine workings, drift, raise, or stope, would be dangerous in a degree, but the draft there is likely to be less strong than in a shaft and probably a smaller area would be invaded by the fire gases. At the Copper Queen mine, in all drifts connecting with individual

Jan 1, 1918

By Sam Harlan

At intervals during the past several years the oil industry has been confronted with the problem of forestalling crises in its affairs. These crises have been reduced to periods of depression which, fortunately, the industry has been able to survive. Under the existing competitive practices which control the producing division of the industry it apparently has been proved that the best efforts logically to curtail development and producing operations are inadequate for effecting a true production balance and the consequent stabilization of prices. The industry is awakening to the fact that the situation warrants revolutionary thought and at this time it is looking for a permanent solution of its problem in a general plan for unit development and operation such as the one first proposed by Henry L. Doherty. Mr. Doherty&apos;s proposal was designed not only as a means for stabilizing the industry as a whole, but its principles involve very definite potential benefits for the average individual operator and royalty owner as participants in pooled projects. The benefits to these individuals would be derived from maximum recovery, the maximum utilization of natural energies, the minimization of development and operating costs, enhanced values of leases and royalties through improved efficiencies and ultimate yields, improved earnings through stabilized crude oil prices, etc. This plan was revolutionary to the industry&apos;s practices and at the time was rejected, but it now appears that the development and operating policies for new properties are continually approaching the ideal of the original plan. Oil companies are constantly extending their efforts to improve all factors that have a bearing on the costs and efficiencies of their operations. These efforts may, in some degree, be a normal outgrowth of the industry&apos;s progress, but the forced consideration of market conditions, the growing appreciation of the importance of regulating operations for maximum ultimate economies and the depreciation of the old principle of maximum flush at any cost, come from a new school of thought which has been stimulated by the immediate pressure of overproduction and

Jan 1, 1930

By R. C. Ku, R. G. Davies

The stress-strain behavior of Fe-C and Fe-Ni solid-solution alloys has been investigated at 25°C. It is found that the rate of solid-solution strengthening is dependent upon the strain at which the yield stress is measured, the macroyield stress being much more concentration-dependent than the microyield stress. In fact the addition of nickel does not lead to any increase in the microyield stress of iron. The primary effect of increasing the carbon or nickel content is to increase the slope of the stress-strain curve in the microyield region; this effect has been correlated, by means of transmission electron microscopy, with a decreased ability of the dislocations to cross-slip. It is concluded that the Mott-Nabarro theory is a good description of true solid-solution hardening in these and other iron-base alloys. A.LL theories of the solid-solution strengthening1-4 indicate that the flow stress of an alloy increases both with solute concentration and "misfit" between the solvent and solute atoms. The functional relationship between strength, solute concentration, C, and misfit depends upon the particular theory. Mott and Nabarro1,2 and Schoeck and Seeger3 both predict a linear increase in strength with concentration, while Fleischer4 indicates that the strength should be proportional to C1/2; there are in the literature experimental observations to support both these compositional dependencies.1&apos;8 The experimental evidence used to support the theories is the change in macroscopic yield stress (strain, e, = 10-3) with composition. However, recent investigations have revealed that solid-solution strengthening in a Cu-Al single crystals7 and in Fe-V polycrystal-line" alloys depends upon the strain at which the flow stress is measured; a flow stress in the microplastic range (e = 10-6 to 10-5) is much less concentration-dependent than the macroyield stress. Since the theories of solid-solution strengthening are concerned in particular with the stress to move a dislocation in a dislocation-free matrix, they should only be compared with microyield-stress data; it will be shown that in a material deforming homogeneously the microyield stress (e = 10-6) is approximately the stress to move through the matrix those dislocations which have been nucleated by stress concentrations such as particles or grain boundary ledges.9-11 In contrast, the macro-yield stress is more complex in that it is affected by several phenomena: dislocation multiplication, dislocation interactions, and the ease of propagating slip across grain boundaries. For example, it is experimentally observed that when long-range order12&apos;13 or solute effects10 restrict cross alip the grain boundary

Jan 1, 1967

By Pei-Yung Huang, C. R. Hayward

In order to understand more fully the actual state of copper lost in copper reverberatory slags, a systematic study on the various reactions between certain metallurgically important copper compounds and synthetic copper reverberatory slags was undertaken by the authors in the Massachusetts Institute of Technology from 1942 to 1945.1 This paper, being only a part of the work completed, is published first because it furnishes the first experimental evidence of the formation of copper ferrite from reactions between cuprous oxide and copper reverberatory slags. Choice of Slag Composition The choice of the composition of the synthetic reverberatory slags to be used was much deliberated. Commercial copper reverberatory slags, neglecting minor constituents, avcrage :2,3 45 to 47 pct FeO; 38 to 42 pct SiO2; 5 to 6 pct CaO; 5 to 6 pct A12O3. Since the ternary system CaO-FeO-SiO2 has been much more thoroughly studied4 and is much simpler than the quaternary system CaO-FeO-SiO2-Al2O3, it was decided to use calcium oxide only instead of calcium oxide and alumina in the synthesis of the slags. Fortunately the composition of the average copper reverberatory slag with calcium oxide substituted for alumina lies in the region of the phase diagram clarified by the investigators. A survey of the phase diagram (Fig I) suggested two compositions: (I) the composition near the invariant point S, which is made up of 46 pct ferrous oxide, 37 pct silica and 17 pct calcium oxide; (2) the composition near the invariant point K with 45.5 pct ferrous oxide, 43 pct silica and 11.5 pct calcium oxide. Composition S has the advantage that the percentages of ferrous oxide and of silica almost exactly coincide with those of the average reverberatory slags, and that of the lowest melting point (1093º ± 3ºC) in the whole ternary system. The calcium oxide content, however, obviously is high. Since we have already substituted calcium oxide for alumina, and since calcium oxide is more basic than alumina, the fulfil- slag is decidedly too basic. Composition K has a slightly higher melting point (1150O + 3OC) and a higher silica content, but this is preferred because the slag is saturated with respect to tri-dymite and thus should not corrode siliceous refractories. Besides, it is less basic than composition S. The filial slag composition, therefore, was chosen to

Jan 1, 1949

By T. E. Leontis

The importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication, attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne. The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Znt alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-~Zn,f Mg-jZn, Mg-4.4211, Mg-6Zn, and Mg-roZn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. Literature The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison. Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,&apos; Dumas and Rockaert, Haugh-ton and Prytherch,6 and by Spitaler, the last being reported by Beck.&apos; A slight superiority in the tensile strength of chill-cent Mg + 8 es alloy Over the sand-cast alloy was noted by Maybrey.8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1949

By Ian J. Smalley

"Quickclay is an extreme case, it is by far the most mobile of all the common solid materials on the earth&apos;s surface. It has both a high water content and a mineral texture that allows it to flow with the utmost ease. A mass of quickclay that has lain undisturbed for thousands of years can be jarred into motion by any sudden shock." The quotation is from the paper by Kerr called, "Quickclay," which was published in Scientific American in 1963. This was probably the most widely read paper on quickclay ever published. It was reprinted by Fred Betz in his Benchmark collection on Environmental Geology (BM 25), A quickclay is an extremely sensitive soil. The sensitivity parameter is produced by dividing the undisturbed shear strength by the remoulded shear strength. If a value greater than 50 is obtained, then the soil can be classified as a quickclay. True quickclays are characterized by a very low remoulded strength of the order of 0.5 kPa. The classic quickclays are found in Scandinavia and Eastern Canada, but the 1964 Alaska earthquake revealed a considerable quick¬clay deposit underlying the town of Anchorage. This was discussed in a classic paper by Kerr and Drew in Engineering Geology in 1967. The Kerr views on quickclays were perhaps most clearly expressed in the paper with Liebling in Geol. Soc. Amer. Bull. in 1965. They suggested that the major critical conditions which contribute to quickclay movement are: substantial quantities of layer lattice silicates of colloidal size (about 40% or more by dry weight), sub¬stantial pore water (44%), a reduction in electrolyte concentration below 5 g/l of salt, and addition of a dispersant. There is still discussion and disagreement about the nature of quickclays and the mechanisms of quickclay slides; the "clay mineral"-based views favored by Kerr still find support, although an alternative "primary mineral" view suggests that it is the finely ground primary minerals

Jan 1, 1985

By J. S. Kasper, R. M. Waterstrat

IN view of the recent findings of a pronounced ordering of atoms in s phase alloys containing elements of the first long row of the periodic table (and including molybdenum),l it is of interest to resolve the question of ordering for s phases containing second and third-row elements. Examples of the latter have been provided recently by Greenfield and Beck2 and two of them, Re-Cr and Ru-Cr, would appear to be favorable for a study of ordering by X-ray diffraction methods because of the considerable differences in the scattering factors concerned. In addition, s phase is found to occur in the Os-Cr system, where the difference in scattering factors is even larger. Accordingly, X-ray powder intensities have been measured in an attempt to learn the nature of the ordering, if any, in these three v alloys. Since there is no reported work on intermediate phases in the Os-Cr system, an exploratory investigation was made in this system, and it was found that, in addition to the s phase, the phase with the A-15 or ß-W structure also occurs. Specimen Preparation—The alloys were prepared by compressing mixed powders of —200 mesh size and sintering in an atmosphere of pure dry hydrogen. All alloys were rapidly cooled from the annealing temperature to room temperature in a stream of cold dry hydrogen in a water-cooled chamber. Table I lists the sources and purities of the starting materials, as well as the details of processing for each of the alloys investigated. Intermediate Phases in the Os-Cr System—In the absence of information on intermediate phases in the Os-Cr system, it was suspected that this system would resemble that of Ru-Cr, where a s phase, RuCr2,2 and a phase with the A-15 structure, RuCr3,3,4 have been identified. Both these phases were found in the Os-Cr system and at compositions

Jan 1, 1958

By J. T. Burwell

The crystal orientation in silicon iron that has been given a particular treatment described by Goss,l has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualitative. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200. It is now generally agreed that Goss&apos;s original conclusion1 that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom. X-ray Data A strip of the material containing 3.1 per cent Si, prepared by Goss,† 1.2 by 0.0125 in., was etched rapidly in warm dilute hydrochloric acid until it was 0.005 in. thick, in order to eliminate the effect of the two surface layers. The specimen was then mounted in an integrating camera similar to one described in the literature.4 The purpose of this camera is to translate the specimen during exposure, so that a statistically large number of grains contribute to the pattern photographed. The camera also allows the plane of the specimen to make various angles with the X-ray beam. An area 5 by 1.2 in. was scanned by a beam of unfiltered radiation from a molybdenum target tube operating at 37 kv., and the measurements were made principally on the peak of the white radiation. X-ray photographs were taken at intervals of 15" in a plane

Jan 1, 1940

By M. Van Siclen

THE outstanding fact in connection with dust disease in the United States at present is the growing recognition of its seriousness by state officials and by the more progressive operators of mining, metallurgical and allied industrial plants. The same may perhaps be said of labor in some of its better organized centers, but the average independent non-union workman continues, as of yore, to suffer the toll of disability and even of death from dust inhalation without realization of the source of his ill-being. Progress in the betterment of the handling of sufferers from dust disease and of the conditions creating dust hazards in mining and allied industries is pursuing a course similar to that of the now widespread campaign against accidents, in which the risk is more obvious, more severe, and was naturally recognized sooner. The coming on of dust disease is generally relatively slow and its immediate effects not infre-quently masked by or attributed to other diseases. Marked exceptions to this general rule have occurred in districts where the dust is particularly pernicious, such as the Rand and Joplin; yet such exceptions, unhappy in themselves, opened the eyes of medical men, and of those in other localities charged with the responsibility for the welfare of industry, to the much more widespread if less spectacular hazard existing from the inhalation of dust in all rock-excavating operations and all industrial operations creating inorganic dust, whether it be crushing and grinding, sand-blast-ing, granite-cutting, or what not. Advancement to date in the United States in prevention and treat-ment has been slow, yet the record shows that quantitative methods for determining the degree of hazard and means for decreasing it were being developed as far back as 25 years ago; and that more rapid progress may be looked for from now on. In 1908, in this country, F. L Hoffman?(1) discussed the mortality from consumption in dusty trades, especially brass foundries; and in 1913 E. R. Hayhurst(2) described the effects of inhalation

Jan 1, 1933

By J. T. Burwell

The crystal orientation in silicon iron that has been given a particular treatment described by Goss,l has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualitative. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200. It is now generally agreed that Goss&apos;s original conclusion1 that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom. X-ray Data A strip of the material containing 3.1 per cent Si, prepared by Goss,† 1.2 by 0.0125 in., was etched rapidly in warm dilute hydrochloric acid until it was 0.005 in. thick, in order to eliminate the effect of the two surface layers. The specimen was then mounted in an integrating camera similar to one described in the literature.4 The purpose of this camera is to translate the specimen during exposure, so that a statistically large number of grains contribute to the pattern photographed. The camera also allows the plane of the specimen to make various angles with the X-ray beam. An area 5 by 1.2 in. was scanned by a beam of unfiltered radiation from a molybdenum target tube operating at 37 kv., and the measurements were made principally on the peak of the white radiation. X-ray photographs were taken at intervals of 15" in a plane

Jan 1, 1940

By C. A. Eligwe, F. W. DeVries, A. E. Torma

This study is an investigation on using hydrogen peroxide for tank-leaching of uranium with sulfuric acid. The optimum sulfuric acid concentration was found to be 0.03 mole 11 -&apos;for a 25% pulp density suspension. The order of reaction with respect to sulfuric acid concentration was found to be ns0.75. The best results vith hydrogen peroxide were obtained at a 4.64 molar ratio of 6202 to U in the ore. The order of reaction was found to be zero with respect to hydrogen peroxide concentration. The theoretical maximum rate effect of Hz02 on uranium extraction was derived as Vm = 8.15 x mole &-&apos;min-&apos;. The highest rate experimentally attained was 8.09 x mole kL&apos;min-&apos;. It was found that the uranium extrac- tion was not affected by the pulp density up to the 50% used in this study. However, the final yieldswere significantly higher (over 90%) for leaches carried out in the presence of Hz02 than (less than 90%) for leaches carried out in the absence of H202. The reaction was found to follow a first order course with respect to substrate concentration (pulp density) regardless of the presence of H202. The effect of temperature was more explicit at moderate tempetatures (30 to 55 C) than at lower (10 C) or at higher (70 C) temperatures. At this latter temperature an almost complete extraction was realized even without H202. The apparent activation energies were found to be AEa = 2.68 kJ mole-&apos; in the absence of H202, 0.5 kJ mole-&apos;with Hz02 at 40 C to 70 C. and 4.72 kJ mole-&apos; with Hz02 at 10 C to 40 C. All these activation energy values suggested that the uranium extraction process is diffusion controlled regardless of the presence of H202. Further, the change in activation energy in the presence of Hz02 indicates the possibility of change in the reaction mechanisms at lower and higher temperatures.

Jan 1, 1980

By W. R. Finlay, W. R. Jr. Hibbard

The key feature of the lattice coherency theory of precipitation hardening1 is the forced coherence between matrix and precipitate which elastically strains both lattices and is believed to be the major source of strengthening in precipitation hardening. In systems exhibiting age hardening, the atom movements leading to precipitation are not at all extensive and are such as to require the minimum amount of energy to produce the interface; that is, the new lattice forms in such a way as to be as nearly as possible a continuation of the old with a matched, coherent plane at the interface at least during the initiation of the precipitation. The crystallographic sequence whereby regions of the matrix change to the precipitate lattice usually can be resolved into a set of shearing operations.6&apos;6 Conversely, the perhaps novel speculation is made that solution of a second phase is accompanied by shearing movements which are possibly the reverse of the precipitation shearing movements. A basic premise of the investigation reported in this paper is that precipitation and solution shearing movements constitute structural weaknesses which might cooperate with applied stresses to facilitate plastic deformation. Another basic premise of the investigation is that the application of hydrostatic pressure to a precipitation hardening system will significantly alter the degree of disregistry across the matrix-precipitate interface and thereby significantly affect the course of age hardening. Two binary precipitation hardening systems were investigated: rz pct zinc in aluminum which undergoes transformations, both precipitation and solution, by a simple crystallographic mechanism; and 4 pet copper in aluminum which undergoes a complex transformation in precipitating and dissolving a second phase. The effects of the application of uniaxial tensile creep stress during elevated temperature aging of both systems and of hydrostatic pressure during the elevated temperature aging of 12 pct aluminum-zinc were then investigated. Previous Investigations Van Wert in 1935,~ studied the effect of hydrostatic pressure on the room temperature age hardening of a few precipitation hardening systems. The latter were rather unfortunately selected since none is known to exhibit any marked volume change on aging and the majority were complex commercial alloys the precipitation mechanisms of which are not known. Jenkins, Bucknall and Jenkins~n,~ in 1944, applied tensile creep stresses to a complex copper. nickel-silicon alloy at various temperatures. The complexity of the alloy and the industrial objective of the work did not permit an appreciable addition to the theoretical understanding of either deformation or precipitation hardening.

Jan 1, 1949