Search Documents

By J. E. House, J. L. Drobnick, R. R. Swanson, D. W. Agers

Since the commercial acceptance of the liquid ion exchange process in the mineral processing industry, it has been predicted that eventually the hydrometallurgist would have a wide selection of commercially available chemical reagents to make separations efficiently and economically of virtually all metals in solution under a wide range of conditions. Several years ago, General Mills began a research and development program to determine if it were possible to develop a reagent to extract a specific metallic ion from solution at a cost that would allow large scale commercial application. A giant step toward reaching this objective was announced in late 1963, when development quantities of LIX®-63 reagent, a highly selective reagent for the extraction of copper, were first offered to industry. The properties of this reagent were de- scribed in a previous paper.1

Jan 12, 1965

By Hobart M. Kraner

THE mineralogy of blast furnace sinter is of interest because its mineral content is one of the important factors contributing to its character. There are so many other factors affecting the properties of the sinter, however, that it is well to mention them here. The proportion and character of the raw materials, that is, raw ores, concentrates, returns, and fuel, as well as the mixing and the water content, all have a marked effect on the physical properties of the product and the degree to which sintering action can be carried on. The process of sintering is a relatively fast operation. In as much as appreciable time is required to carry on processes of fusion in such masses of low thermal conductivity, large lumps of hematite ore frequently remain unfused and partly unchanged in state of oxidation in the sintering process. The kind, the grain size, and the amount of fuel used affect both the completeness of the fluxing reaction and the prevailing atmosphere. The rate of reduction in laboratory tests is not only dependent upon the state of oxidation of the sinter but also upon the sizing and porosity.

Jan 11, 1953

By R. B. Tippin

Laboratory and pilot plant studies showed that supergrade iron ore concentrates (containing less than 2% SiO2) can be made from standard grade magnetic iron ore products by cationic silica flotation. Continuous tests were run using various flowsheet arrangements. whereby (1) super and standard grade products were made simultaneously or (2) only a superconcentrate was produced. After a caustic scrub and desliming pretreatment, the silica in a magnetic taconite concentrate was reduced to 1.8% SiO2 by amine flotation. Approximately 75% of the iron was recovered in the single flotation stage, and by additional beneficiation 95% of the total iron was ultimately recovered,

Jan 1, 1973

By Peter J. Szabo

INTRODUCTION The time period from the detailed feasibility study to the post investment audity usually ranges from three to eight years depending upon the nature of the mining project considered. It is the only after the post investment audit that we know the adequacy of the assumptions made concerning operational risk assessment in the detailed feasibility or acquisition economics. The post investment audit results from numerous mining projects can best be described by a verse by John Greenleaf Whittier's Maaud Muller. It reads "For all sad words of tongue or pen the saddest are these 'It might have been!"' Dissecting the negative results of numerous mining projects we find faulty assumptions concerning markets, geology, capital investment and operational risk assessment. Although in hindsight many of these assumptions could have been considered impossible or impracticle to have forecast with any degree of certainty, we find that refined assumptions concerning operational risk assessment could have been made with only a modicum of additional "Due Diligence". Anyone who invests in a mining property should employ a much higher discount rate of future cash flow, (usually in the minimum range of 25%-30%), than he would expect from such safe investments as Treasury Bills or high grade Utility Bonds. The nature of this steep discount translates to a large uncertainty concerning the timing and actualization of assumptions contained in the detailed feasibility study. We must remember that when a project gets beyond 20 years, any contribution to the value of the project of cash flow is minimal due to the nature of the discounting process. Thus for each full or partial day lost in the development or early operation stage of a project, the financial impact will be greater than similar lost days later on in the project. Adequate operational risk assissment is particularly critical when bidding on competitive tenders for coal deposists in remote locations such as the Bowen Basin in Queensland, Australia. Because of the market attractiveness of these coal deposits for supplying end users in the Far East, Middle East and Europe, state governments require competitive tender biddings via the Authority to Prospect process. Front end bonuses and super royalty payments must be commited before the actual mining conditions are known. Time to submit firm offers from the actual request for proposal vary from 90 to 120 days. Thus any operational risk assessment must be detailed, realistic and reflective of the actual project. When one searches the literature, one finds limited qualitative data on operational risk assessment in valuation papers. Usually this facet of valuation takes a secondary role to such areas as reserves, markets, and environmental considerations. When one comes to the question of operational risk assessment more often than not one finds the use of "rules-of-thumb", such as tons per man shift, average production, average seam height, etc., are used to forecast results on which banks and other financial institutions are required to make investment decisions. Because of the extremely competitive environment of the 1970's and 1980's numerous financial institutions approved loans without adequate "Due Diligence", and are currently paying a steep price in terms of non performing loans and charge offs. One must always remember that each operation is unique with its own characteristic

Jan 1, 1985

By B. L. Thane

Within the past few years, the mining industry has taken a new impetus in all its branches. New mines are being opened every day, while old ones, which have been either working at a loss, or have been compelled to shut down, are now gradually being reopened and placed on a paying basis. This growth and new life is due, in a measure, to the discovery of new mining districts, but the most important cause of the progress is the wonderful advance that has been made in all branches of mine-engineering. By means of the important inventions and discoveries that have been made in mechanics, chemistry, and electricity, we are now able to work ores which, only a short time ago, would have been regarded as worthless. We find, for instance, the electrician eliminating two of our greatest difficulties, those of distance and superior elevation, while the mechanic has brought to the highest degree of perfection, not only ore-crushing and hoisting machinery, but all such devices as pertain to the mechanical handling of ores, and, at the same time, the metallurgist, with his combined chemical and mechanical skill, has helped us to extract the precious metals from the most refractory of ores. But when we turn to examine methods in actual use for

Jan 1, 1900

By K. V. Hoover, D. M. Lapham

In Pennsylvania, 310 sampled sites of clay and shale have been studied with regard to potential use, lithology, physical properties, fired properties, major-element chemical analyses, and quantitative five-component X-ray mineralogy. Approximately 80% of the samples are of some potential use. Binary correlations of test data vs. potential use indicate that certain empirically determined parameters may be critical. These are: lithology, particularly for medium to superduty refractories and lightweight aggregate; kaolinite content for refractories vs. low-temperature fired product sources; quartz analyses with an apparent necessary minimum quantity for brick; quartz content, which is low in high grades of lightweight aggregate; mica content, which is low for refractories and possibly high for lightweight aggregate; total iron, which is low for refractories and shows a 4.0% minimum for lightweight aggregate; carbon dioxide, which is low for refractories, beneficial in lightweight aggregate, and probably restrictive for some tiles; chlorite-vermicalite, which is low for refractories and possibly beneficial in lightweight aggregate. In Pennsylvania, clay and shale materials constitute one of the state's major economic mineral resources. To date, the testing program indicates considerable development potential in brick, tile, and lightweight aggregate industries and perhaps a future potential for aluminum from shales that exceed 20% AID..

Jan 1, 1972

By Edward Sayre

IN shaft sinking for coal mines, the cost item greatly influences the method adopted. This holds true especially when soft material must be traversed. The average life of a coal mine is short. This is clue either to the limited area of the coal basin or to the great expense of maintenance and haulage underground when the entries are extended a considerable distance from the hoisting shaft. Therefore, the engineer in opening a coal mine is confronted with the fact that the cost must be kept within certain bounds else the venture will prove unprofitable. For this reason he may be prohibited from adopting certain safe, but expensive, methods that are used in sinking caissons for foundations, driving transportation tunnels, or other work of permanent construction. A common method of sinking through difficult ground employs the aid of a steel shoe pushed ahead of the shaft timbers. Another is the drop-shaft method. These two methods were used in sinking the main shaft and the air shaft of the Eagle No. 3 mine, at Des Moines, Ia., and the following data show the relative success and cost of the two methods of sinking under the same conditions. A drill log of the material to be penetrated was as follows (see Plate 1, Fig. .1)

Jan 9, 1916

By Robert A. Cummings, Francis S. Kendorski

The behavior of the rock mass during block caving affects the production of the mine and dictates the loads and deformations placed on required drifts. Traditionally, the drifts used are massively reinforced and buttressed against very high and erratic mining- induced abutment loads or swell muck loads, resulting from undercut- ting. Extensive field investigations in numerous block caving mines in the porphyry intrusive environment, coupled with models developed for tunneling and longwall coal mining, have allowed the development of a unified hypothesis for ore bodies of various degrees of competence. In general, the hypothesis incorporates several sequential steps in the driftlrock mass deformation history, each with characteristic magnitudes, duration, and areal extents depending on ore body competence. 1. Prior to initiating caving, but subsequent to drift development, the rock mass and drift are in a state of near-equilibrium. Zones of stress concentration have stabilized, as for a tunnel. 2. For a newly undercut panel, the rock mass and drifts directly beneath the undercut respond by dilating towards the void created, and undergo a release of compressive strain that manifests itself as tensile failures. 3. For adjacent areas, the rock mass is compressed as the load is shed from the undercut level.

Jan 1, 1983

By Jacques B. Wertz

Both the San Andreas fault complex and the Murray fracture zone are apparently found to be contemporaneous with the Laramide mineralization period. Their compounding effects certainly have disturbed the Texas lineament belt and its components with serious lateral offsets and most probably have been instrumental in allowing intrusives to be emplaced as well as mineralization to accompany these intrusions at some of the fracture intersections. While the main fracture centers can be almost accepted as being structurally linked together, the Texas lineament trend definitely predominates, exerting a prevailing direction to graben (Silver Bell) and to elongated depressions (Bisbee). That this lineament belt also influenced the concomitant mineralization seems a logical inference. The orebodies are generally found at intersections near the most centrally-located intrusive with a distance varying from contiguity to one or two miles. The Southeast Arizona copper province owes its existence primarily to a particularly favorable structural setting of broad semi-continental scope. Thus, various regional structural elements are to be considered as possibly direct or remote cause for the widespread mineralization, although the one or the ones really responsible may never be singled out. There arc three basic regional elements: (1) The north-northwest-trending anticlinorium that diagonally crosses Arizona is quite obvious because many mountain ranges follow this direction. This anti- clinorium, which merges northward into the Wasatch-Jerome Belt, marks a broad zone of weakness where tension seems to prevail. Mineralized trends such as Jerome-San Manuel-Bisbee may give some weight to the economic value of this structural element. (2) Northeast-trending fractures, parallel to the Colorado Mineral Belt (Landwehr, 1967), appear troincident with mineralization as evidenced by the Questa-Grants-Morenci and the Lordsburg- Tyrone-Santa Rita alignments. This structural direction is accepted as one of the most economically significant in the Southwestern United States. (3) The Texas Lineament.

Jan 1, 1970

By Thomas Fraser

"AIR-SAND" is the term which has been given to a process of separating refuse material from coal by means of a body of dry sand artificially fluidized and maintained in that condition by a continuous stream of air bubbles flowing through the sand body. By proper regulation of the rate of air flow, this fluid air-sand body may be maintained at such a density that coal will float near the surface and the refuse, which is heavier, will sink through the sand to the bottom of the container. This separation is a float-and-sink operation similar to the separation of wood chips and stones in water; the one floats and the other sinks, irrespective of size of pieces. This was the objective sought in the development of this method of cleaning coal-a dry process which requires no preliminary sizing of the coal. METHOD OF PRODUCING THE AIR-SAND MEDIUM Figure 1 shows the cast-iron cell used for testing at the Central District Experiment Station of the Bureau of Mines, Urbana, Ill. This consisted of two castings: a. rectangular box 12 in. square in cross section and 18 in. tall, open at both ends and flanged on the bottom; and a cubical box also 12 in. square inside, with a closed bottom and flanged top. A porous diaphragm is bolted between the flanged ends of the two castings. The upper part of the cell above the diaphragm is filled with river sand screened through 20 mesh without removing the dust. Air under suitable pressure is admitted to the lower part of the cell below the diaphragm. The air passes through the diaphragm and bubbles up through the sand, distending the mass and throwing the sand particles into motion.

Jan 2, 1926

By Richard Moldenke

ONE of the gravest problems of the iron foundry today is the accumulation of sulfur in commercial scrap and its effect on the castings made therewith. The ordinary jobbing castings today show a sulfur content of 0.18 per cent., and occasionally as high as 0.22 per cent. The product of the foundry during the war is undoubtedly .to blame for this rapid increase and conditions will become worse as the millions of tons of gray-iron castings of the war period return to the foundry in the form of commercial scrap. In the ordinary cupola remelting of pig and scrap, at least 0.02 per cent. sulfur is taken up; often double that amount. The high cost and difficulty of obtaining pig iron during the war period compelled the use of considerable scrap in the mixtures; frequently charges containing. 90. per cent. of bought scrap were melted. Naturally the sulfur content of the castings increased. Until the advent of the basic-hearth electric furnace, the only method of holding the sulfur within reasonable limits was to use high percentages of pig in the foundry mixtures. Pig iron seldom contains over 0.05 per cent. sulfur, if well made. With pig iron forming 60 percent. of the .charge and the gates, runners, rejections, and bought scrap the other 40 per cent., the sulfur content of the castings can easily be held down to 0.10 per cent. Pig iron, however, costs more than scrap even when melting loss differences are considered, hence as small a percentage as possible will be used.

Jan 2, 1921

By Richard B. Reese, George R. St. Pierre, Robert A. Rapp

The vapor pressures of pure iron and pure chromium have been measured using a Knudsen cell coupled with a mass spectrometer. The experimental results agree well with some previously reported data; heats of sublimation and vaporization have been calculated. From vapor pressure rr~easurernents, the activities of iron and chromium in their binary alloys have been determined for NcY = 0.10 to 0.65 over a 1400" to 1700~ temperature range. The activity of chromium in the liquid alloys was found to exhibit positive deviation from ideal behavior when referred to solid chromium as the standard state; however, for the activity of chromium referred to nonequilibrium undercooled liquid chromium as standard state, the activity behavior is almost ideal. ALTHOUGH the Fe-Cr system is important as the basic system of alloy steels, the thermodynamic properties of this system have not been thoroughly investigated at elevated temperatures. In view of the potential practical applications of such data as well as their contribution to alloy theory, further study of the Fe-Cr system was undertaken. In addition, further development of experimental techniques for equilibrium measurements at high temperature is required. The present research involved an application of the Knudsen effusion method in conjunction with a time-of-flight mass spectrometer. Belton and ~ruehan' have measured the activities in Fe-Ni and Fe-Co alloys by a similar method. Speiser, Johnston, and lackbburn' have determined the vapor pressure of pure solid chromium between 1283" and 1561°K by a Langmuir free evaporation technique. The vapor pressure of chromium was described by the expression: over the temperature range 1283" to 1561°K. McCabe, Hudson, and paxton3 have measured the vapor pressures of pure iron and pure chromium by the Knudsen cell technique around 1500°K. The vapor pressure and heat of sublimation at O°K, AH,", for pure chromium agreed within experimental error with the measurements of Speiser et al. at 1200°C. Kubaschewski and HeYmer~ determined the vapor pressure of pure solid chromium in the temperature range 1170" to 1400°C by the Knudsen effusion technique combined with a radioactive tracer analysis of crS1. Their results agreed with the work of previous investigators. Edwards, Johnston, and Ditmars5 have measured the vapor pressure of pure solid iron by the Langmuir technique between 1356" and 1519°K. The vapor pressure of solid iron in the temperature range studied was given by: The data of McCabe, Hudson, and paxton3 on the vapor pressure of pure iron around 1500°K by the Knudsen effusion technique were in good agreement with those obtained by Edwards et a~.~ Hultgren, Orr, Anderson, and Kelley give the selected values for the AH: of pure iron and pure chromium as 98,990 *200 and 94,340 * 500 cal per mole, respectively. These values are the average values determined in the several investigations by different methods. The Fe-Cr phase diagram7 is shown in Fig. 1. Previous determinations of activities in this system have been carried out by several investigators, but most of the work has been done on solid alloys. Using a Knudsen effusion method with cr5', Kubaschewski and Heymer4 reported that the Fe-Cr system exhibits positive deviation from the ideal behavior for compositions ranging from NCr = 0.0398 to 0.699 at 1170"

Jan 1, 1969

By O. N. Carlson, S. A. Bradford

Discontinuous yielding in tensile tests was observed in V-O alloys in the temperature ranges of 150° to 175°C and also 350° to 400°C. The magnitude and intensity of the serrations were found to vary considerably with oxygen content. Maxima were observed in tensile and yield strengths and in the strain-hardening coefficient at the higher temperature only. The strain rate sensitivity was observed to be negative between 150° and 400°C. THIS investigation was undertaken to study the effect of oxygen on the tensile properties of iodide vanadium in the temperature range of 25o to 450°C. Brown1 observed an increase in strength between room temperature and 400°C in vanadium metal, and found that oxygen and nitrogen had a rather pronounced effect on the strength and ductility. A maximum in the tensile strength was observed by Rostoker et al.2 near 300oC and by Pugh3 around 450°C for calcium-reduced vanadium. Pugh also found a maximum in the yield strength and in the strain-hardening exponent, and minima in the elongation and strain rate sensitivity at the same temperature. Eustice and Carlson4 reported the appearance of serrations in the stress-strain curves between 140° and 180°C in iodide vanadium containing 600 ppm O. These anomalies in the mechanical properties indicate that strain aging occurs in vanadium, but the impurity or impurities responsible for the above-mentioned effects have not been identified. The phenomenon of strain aging is usually characterized by the return of the yield point after interruption of a strength test. In the temperature range where strain aging occurs, the yield and tensile strengths attain maximum values, elongation and strain rate sensitivity exhibit minima, and discontinuous yielding is generally observed in the stress-strain curve. Cottrell5, 6 has postulated that strain aging is due to the migration of solute atoms to dislocation sites to produce locking after the dislocations have broken free from their impurity atmospheres during the initial yielding. At the strain-aging temperature the process is a dynamic one in which the solute impurity atoms diffuse to the vicinity of the moving disloca- tion producing "locking" which gives rise to maxima in the tensile strength and serrations in the elongation curves. Cottrel17 has noted that discontinuous yielding in iron occurs when the diffusion coefficient of nitrogen, D, and the strain rate, i, are related by D = 10-9 €. EXPERTMENTAL PROCEDURE The vanadium metal employed in this study was prepared by the iodide refining process as described by Carlson and owen.8 A representative analysis of the vanadium used in this investigation was: 150 ppm O, <5 ppm N, <1 ppm H, 150 ppm C, 150 ppm Fe, 70 ppm Cr, <50 ppm Si, 30ppm Cu, 20 ppm Ni, <20 ppm Ca, <20 ppm Mg and <20 ppm Ti. Alloys containing from 200 to 1800 ppm O, all of which lie in the solid solution range of the V-O system, were prepared by arc melting vanadium together with portions of a high-oxygen master alloy. The master alloy was prepared by tamping pure V2O5 into holes drilled in a vanadium ingot and arc melting this five or six times in an inert gas atmosphere, inverting the button between each melting step. The oxygen content of the master alloy was then determined by vacuum fusion analysis. Vanadium containing less than 150 ppm O was prepared in the following manner. A bar of iodide vanadium was deoxidized by sealing it in a tantalum crucible with a few grams of high-purity calcium. This was held at 1100°C for 4 days to allow time for the oxygen to diffuse to the surface and to react with the calcium vapors. The calcium oxide product was later dissolved from the surface of the bar with dilute acetic acid. In this way vanadium containing from 20 to 50 ppm O was prepared. Sample Preparation. The are-melted ingots were cold swaged into 3/16-in. diam rods and these were machined into cylindrical tensile specimens with a reduced section of 1.00-in. length and 0.120-in. diam. The test specimens were annealed for 4 hr at 900°C in a dynamic vacuum of mm of Hg to remove hydrogen from the metal. This recrystal-lization treatment produced a uniformly fine-grained structure with a mean grain size of approximately 0.06-mm diam. The oxygen contents reported in this paper were determined by a vacuum fusion analysis of the tensile specimens after testing. Analyses for other interstitial or metallic impurities showed no significant changes from that of the original material. Tension Tests. Tension tests were performed on a screw-driven tensile machine at a constant cross-head speed of 0.01 in. per min. Tests at elevated temperatures were carried out by heating the

Jan 1, 1962

By Charles Willis

THE time is no longer when a man can act as an independent unit; the appreciation of the interdependence of one man upon another has emphasized the importance of the social unit. Epidemics have made us recognize that even a man&apos;s health is not distinctly his own to control as he pleases. The physical examination of workmen previous to employment started with an effort to prevent the spread of tuberculosis, for tuberculosis may be .detected in its early stages and cured. But it was soon found that many other diseases were detected and the saving of lives made possible. The physical examination does not mean the elimination of the unfit-on that basis it would utterly fail- but rather the measuring of a man&apos;s physical fitness and placing the man where he can do the best for himself, his fellow worker, and the company. Industry as a whole cannot expect to live up to the standard of physical examination set for the army, nor should it expect to do so, for in all branches of industry there are types of work that do not require -the same amount of endurance as does army work, and the placing of men with physical limitations in the work for which they are&apos; capable permits a higher average of physical fitness for the work requiring physical excellence.

Jan 7, 1919

By William G. Gates

INTRODUCTION The Heath Steele mine is located in the Bathurst-Newcastle area of northern New Brunswick. It is jointly owned by American Metal Climax, Inc. and the International Nickel Company of Canada who hold a 75% and 25% interest, respectively. The ore deposits of lead, zinc and copper sulphide occur in very fine grained pyrite and/or pyrrhotite masses. A consistent spatial relationship with a quartz feldspar porphyry is characteristic of these deposits and the many other similar sulphide deposits in the district. The two principal mineral assemblages of pyrite-sphalerite-galena, and pyrrhotite-chalcopyrite-pyrite, occupy characteristic positions relative to the enclosing rocks. This feature and the nature of the sulphide mineralization are described and the variations in metal content are noted .with special emphasis on the lead-zinc ore zones. The mine product ion rate is 3,000 tons per day of a mixed lead- zinc and copper ore which is extracted from the B-1 zone. The complex nature of the ores presents many metallurgical problems. Optimum metal recoveries are achieved when milll feed grades are relatively consistent and proportions of the contained metals are with in acceptable limits. Ore outlines and stoping blocks are delimited by close spaced diamond drilling. From this information it is possible to forecast the grade of any portion of a stoping block. Production from the various stopes may then be scheduled so as to achieve an acceptable mill feed grade.

Jan 1, 1970

By Henry Wurtz

Jan 1, 1880

By L. Dudley Stamp

On April 1, 1937, Burma, formerly a province of the Indian Empire, was formally separated from India and became an independent unit of the British Commonwealth. In future, therefore, statistics of oil production in India will exclude Burma and those for Burma will be separately published. The last few years have been marked by noteworthy, almost spectacular, developments in the oil fields of Burma and the Punjab. In Burma these developments have been the proving of unexpected extensions of the existing fields and not the discovery of entirely new fields. The new extensions are important not only to Burma in giving a new lease of life to her fields, but also in general as stressing some interesting geological aspects hitherto neglected. Production The production of crude oil in Imperial gallons has been: Burma India 1934 254,760,070 67,265,210 1935 251,338,974 . 71,323,362 1936 265,656,393 69,241,504 1937 (eat.) 270,000,000 70,000,000 The Chindwin Fields.—The small field at Indaw continues to produce steadily about 3,000,000 gal. a year, but no really deep test has yet been successfully carried out and resources are thus not yet fully known. The remote location of the field, inaccessible except by river and situated 22 miles from the Chindwin 270 miles up that river from its junction with the Irrawaddy, has not encouraged active exploitation. The field is worked exclusively by the Indo-Burma Petroleum Co., Ltd. (I.B.P.), using now an automatic gas-lift system, and the company formerly refined the oil at a small refinery at Pantha on the river near by. The chief market was for kerosene in upper Burma. The refinery has now been closed. The oil is stored on the field during the low-water season

Jan 1, 1938

By J. W. Turrentine

SECONDARY fertilizer minerals include borax, gypsum and sulphur and such compounds as the sulphates of copper, magnesium, manganese and zinc; also the carbonate and oxide of magnesium. Potash, phosphates and nitrogen are generally considered to be primary fertilizer materials. The growing plant, under the average conditions of growth, is able to get from the soil the mineral elements required for the completion of its life cycle. The elements taken up are numerous and the vital functions of some of them yet remain to be determined. However, in the commercial growing of the plant (farming) something much more than the mere completion of a life cycle is required. There the maxi- mum possible growth of plant or yield of seed or fruit are the objective and for that objective the average soil is deficient in some elements, and additions from artificial sources are desirable. Commercial fertilizers (15,000,000 tons in 1946) are designed to supply those deficiencies. Long experience has taught that nitrogen, phosphorus, and potassium are the elements most apt to be required and in a greater degree, and to supply them is the-basic function of the fertilizer industry. Thus nitrogen, phosphate, and potash are designated as the major plant-food materials. But other mineral crop nutrients may likewise be deficient in varying degrees as determined by diagnostic techniques, soil tests, plant analysis and foliar symptoms,3 calling for their addition from artificial sources if maximum crop yields are to be obtained. Because used in lesser amounts and frequently in relatively minute amounts as compared with the major three, they are designated either as "minor elements," or, if used in larger amounts, as "secondary elements." Thus, included under the two designations, in alphabetical order, are: borax; copper sulphate; magnesium carbonate, oxide and sulphate; manganese sulphate, and zinc sulphate. Obviously, the sulphates of the metals copper, manganese, and zinc cannot be considered as "industrial rocks," but they are given brief mention for whatever interest may pertain there to.

Jan 1, 1949

By JAMES J. PURDY

The great majority of stokers used in residential heating installations are of the clinkering type. Because of inherent characteristics of the under- feed combustion process as it occurs in these small stokers, and because of the wide range of operating conditions encountered in residential heating schedules, not all bituminous coals can be used successfully in residential underfeed units. The problem of providing consumer satisfaction has been attacked by the joint efforts of the stoker manufacturers and the coal industry; the stoker manufacturers have been concerned with improving their product to permit the use of a wider range of coals, and coal operators have made every effort to market selected and better prepared coals. In view of the wide range of physical characteristics and chemical properties of bituminous coals, the problems are real and are receiving increased attention.

Jan 1, 1949

By Ralph Sweetser

IN these days of the almost exclusive use of byproduct coke as the blast-furnace fuel in this country, it may seem out of place, and smacking too much of reminiscing, to say anything about the use of anthracite coal for blast-furnace fuel. Viewed in the light of present day research and of developments in alloy steel, some observations seem appropri-ate regarding this raw material that played such an important part in the development of the iron and steel industry during 50 years of the past century. The research work of that period, in which the whole iron and steel industry was revolutionized, passing from wrought iron to steel and from charcoal to three new mineral fuels for blast furnaces, was done chiefly in the full-sized plants of that day; and it was done largely by the ironmasters themselves. The laboratory had not become a part of the ironworks, and scientific instruments were lacking around the blast fur-naces; "rule o&apos; thumb" and erroneous theories prevailed-and have not yet all been eliminated. The recent interest in meteoric iron in connec-tion with nickel steels and other alloys proves that it is worth while to search for the reasons for excellence and the causes for failures in the metallurgy of bygone days. Turner1 gives the reasons why the blast furnace of Dr. F. W. Geissen-hainer on Silver Creek, Schuylkill County, Pennsylvania, about 10 miles northeast of Pottsville, was operated successfully with anthracite2 in August and September, 1836, and why several other attempts failed. It has taken a long time for us to find out that there are great differences in the behavior of anthracites from the several parts of the anthracite region, as well as differences in coking coals from the bituminous fields.

Jan 1, 1935