Search Documents

By F. L. Wolf, A. A. Grubb

The tests here described were rrlade to obtain information regarding costs, efficiency, etc. of baking cores in an oil-fired oven and two electric ovens, which were installed, early in 1920, in the core room of The Ohio Brass Co. and were used almost continuously during the rest of that year. Operating costs were rather high so a complete test was undertaken early in 1921. The ovens will be referred to as Nos. 1, 2, and 3. Nos. 1 and 2 are electric ovens of different makes while No. 3 is an oil-fired oven made by the firm that made No. 2. The three arc. equipped with similar ventilating devices. They have full-height doors at front and rear. The cores are placed on iron racks, which arc lifted by Cowan trucks and rolled into the ovens through the front doors. When baked, they are removed through the rear doors. Fig. 1 shows the general plan of the elecric ovens while Fig. 2 shows the plan of the oil-fired oven. Oven No. 1 is 91 in. (231 em.) wide, 83 in. (210 em.) high. and 79 in. (200 cm.) deep, inside measurements. The walls are constructed ill panels about 18 in. (46 cm.) wide and 43/16 in. (10.6 em.) thick, packed with blocks of insulating material and covered with sheet iron. Thc concrete floor oil which the owns set is 13 in. (33 cm.) thick. 4 recess about 5 in. (13 cm.) deep was cut in the floor to provide room for the heating units. Channels and plates supported on I beams serve as supports for the trucks and racks. The ventilating system consists of a Sirroco No. 11/2 fan, connected so as to draw air from the top of the oven or from the room, through damper C, and to deliver it either to the bottom of the oven or to the floor; the delivery is controlled by the vane A. The fan 2nd pipes are covered with 1/4-in. (6.3 mm.) asbestos-cement lagging. The heating units have a capacity of 91.4 kw. and arc located along

Jan 1, 1923

By E. S. Machlin, S. Weing

GRAIN boundary stress relaxation has been the subject of several investigations in recent years, but as yet the phenomenon is not well understood. One of the major difficulties has been the lack of a sufficient amount of data with which to evaluate any proposed mechanism. Little information is available on the effect of small amounts of substitutional solutes on grain boundary stress relaxation. It is with this important phase of the problem that this investigation is concerned. The influence of substitutional solutes on grain boundary stress relaxation has been recently investigated in copper by Pearson: and in aluminum by Dorn et al.' Pearson studied the effect of zinc, gallium, germanium, and arsenic on the relaxation peak of OFHC copper.* The pure OFHC copper decreased the peak intensity and a second peak appeared at a higher temperature. This latter peak was termed the alloy grain boundary peak. At the lowest binary concentration studied, approximately 1 atomic pct, the primary peak was almost completely obliterated. Pearson found that the activation energy calculated from the alloy grain boundary peak for all solutes, irrespective of the concentration, was 44,000 cal per mol. Pearson concluded that the increase in activation energy from 33 to 44 kcal per mol is not continuous but abruptly changes from the lower to the higher value. As no attempt was made to investigate the intermediate range of concentration and hence calculate the possible variation of the activation energy for the initial grain boundary peak, this conclusion is hardly valid. In contrast to these results, Dorn et al. studied the effect of zinc, silver, copper, germanium, and magnesium on the grain boundary stress relaxation of aluminum. No change in the energy of activation was observed for binary alloys of the flrst four solutes, but a linear increase was found for increasing concentration of magnesium. Saturation was not found up to the maximum of 1.6 atomic pct. The energies of activation were obtained by plotting the horizontal displacement of the dynamic modulus curve vs temperature for two vibrational frequencies. As the modulus is proportional to the square of the frequency, this requires the measurement of the torsional frequency over a range of temperature. However, the technique does not lead to an unambiguous interpretation of the grain boundary

Jan 1, 1958

By T. D. Murphy

The element silicon, with its usual partner, oxygen, plays the same role on this planet relative to inorganic materials as carbon and hydrogen play with respect to living organisms. The crystallographic structure of silicon dioxide (SiO,) consists of one atom of silicon well-nigh inseparably bonded to four contiguous atoms of oxygen, a gas of but slightly more than half its atomic weight, forming a three-dimensional network of SiO, tetrahedra (Dietz, 1968). This wispy arrangement is the fabric of the mineral quartz which is one of the harder, more abrasive, and chemically stable raw materials to be found in Mother Nature's cupboard. Most of us are vaguely familiar with the observation that nearly 60% of the lithosphere to an approximate depth of 10 miles is composed of these two elements, which proportion actually rises to about 75% if the atmosphere, hydrosphere, and biosphere are included (Parker, 1967). Elemental silicon is a brittle steel-gray metalloid with a density of 2.42 and does not occur in nature. In its limited commercial form, which is still brittle and metallic in appearance, its density drops to 2.33. It combines with oxygen to form the gaseous oxide SiO, or the solid dioxide SiO, (analogous to its congener carbon in CO and CO,); a tetrachloride SiCl, (analogous to CC1,); or, combining with oxygen and one or more metal ions, forms the largest rock-making family of all, the silicates. Further, next to the feldspars, quartz is the most abundant known mineral and, in some form or another, accounts for roughly 12% of surficial terrestrial rock. It is this so-called "free silica" to which your attention is chiefly directed in this chapter. In any such consideration of silica, its several crystalline phases with their attendant differing physical properties appear worthy of delineation. Alpha quartz is the only one of this interesting polymorphic family that is thermodynamically stable at normal pressures and temperatures up to about 573°C. The low phases of tridymite and cristobalite can exist in the so-called metastable state below 117°- 200°C but seldom occur in nature in these two different crystal forms (Sosman, 1965). Opaline silica, now considered by most researchers to be a variety of cristobalite, occurs in abundance and is the only exception. The three remaining polymorphs, keatite, coesite, and stishovite, also are metastable under ambient conditions. Keatite, however, is not known to occur naturally and has only been synthesized in the laboratory. The other two have been identified in submicron sizes and in microscopic amounts, occurring naturally as a result of high order shock-wave pressures generating quite elevated temperatures-such as might accompany the impact of a large meteorite on a hard sandstone terrain (Chao, et al., 1962). An intriguing characteristic of these silica minerals, and one which has very practical applications, is their extremely variable densities. The classic 2.65 specific gravity of alpha quartz drops to 2.20 in tridymite, cristobalite, and lechatelierite (natural silica glass), as well as in many man-made glasses of commerce which are merely noncrystalline or amorphous solids in the form of super-cooled liquids which can no longer change their shapes (Pauling, 1950). It rises again to 2.50 and 2.93 for keatite and coesite, respectively, and finally becomes a reported 4.35 for stishovite-nearly a 50% range in density for the known physical combinations that silica naturally assumes (Frondel, 1962; Konnert, et al., 1973; Pecora, 1960).

Jan 1, 1975

By C. K. Gupta, P. K. Jena

Niobium (columbium) metal in the form of a button has been produced by calciothermic reduction of niobium pentoxide using sulfur as the heat booster. In these experiments with 50 g of niobium pentoxide per batch, the influence of percentage of calcium in excess of the stoichiometric, the percentage of sulfur by weight of the niobium oxide, and the outer-wall temperature of the bomb on the quality and yield of the metal has been studied. The maximum yield on this scale was 78 pct using 50 pct excess Ca and 20 pct of S and at a bomb-wall temperature of 600°C. In experiments conducted on 500 g of niobium pentoxide, reduction with 40 pct excess Ca and 20 pct of S, and at a bomb-wall temperature of 500°C, the.yield of the metal improved to 82 to 84 pct. Some of the reduced-metal samples have been electron-beam melted and the button melts thus obtained have been observed to be extremely ductile and capable of cold reduction to 98 pct without intermediate annealing. NIOBIUM, because of its high melting point (2468oC), its ductility, its resistance to corrosion especially in liquid metals, its high-temperature mechanical properties, and its relatively low capture cross section (1.1 barns) for thermal neutrons, has potentialities as a structural material in the field of nuclear engineering. Niobium and its alloys are also gaining importance in high-temperature technology as components in aircrafts, jet engines, and missiles, electronics, chemical engineering, and surgery. In 1904 Weiss and Aichel 1 produced niobium by reduction of its pentoxide by misch-metal. Since then a large number of investigations have been carried out for the extraction of niobium from its compounds. The various routes through which the metal niobium has been extracted from its compounds can broadely be classified into the following groups: a) reduction of its halides, oxides, and fluo-salts with metals like calcium, magnesium, sodium, and aluminum;2-10 b) reduction of its halides with hydrogen and oxides with carbon or carbides;11-18 c) electrolytic winning from its halides and fluo salts;19-25 and d) thermal decomposition and disproportion ion of its halides26-30 Among the processes in commercial use at present are sodium reduction or fused-salt electrolysis of potassium niobium fluoride, carbide or carbon reduction of the oxide, and hydrogen or metallothermic reduction of the chlorides. In 1907 Von Bolton2 prepared niobium by reducing niobium pentoxide with aluminum. Dennis and Adam-sona attempted reducing the oxide with magnesium powder in argon atmosphere and the resulting metal contained as much as 5 pct O. Mondolfo8 claimed a method for the reduction of the oxides with aluminum. In the case of both magnesium and aluminum reduction, it has been stated31 that by-product oxides such as MgO or A12O3 would involve a major separation problem. Further, in the case of alumino-thermic reduction, the solubility of aluminum in niobium and intermetallic formation have to be reckoned with. In 1922 Bridge3 produced niobium by calcium reduction of niobium pentoxide. Dennis and pdamson' obtained the metal by a similar method with an oxygen content of 0.2 pct. In most of the cases of metallothermic reduction of niobium oxides mentioned above, the metal niobium is obtained in the form of powder. In an attempt to produce massive niobium metal, lock' used iodine as the thermal booster in the bomb reduction of niobium pentoxide by calcium. Massive niobium metal was obtained with a maximum yield of 75 pct containing 0.1 pct 0. Joly32 carried out experiments on calcium reduction of niobium pentoxide on a 2-kg scale using sulfur as the heat booster in a sealed bomb filled with argon. In his experiments, the reaction was initiated by passing a current through niobium spiral wire embedded in the charge. In a typical run consisting of 2000 g of niobium pentoxide, 3100 g of calcium, and 800 g of sulfur (S/Nb2O5 = 3.3), he obtained massive metal in the form of a very uneven mass with a yield of -57 pct. With lower amounts of sulfur and calcium, powder niobium mixed with small metal globules was obtained and the yield was also poor. From these experiments he concluded that this method is not a suitable one for industrial development considering the quality and yield of metal obtainable and the possible hazards with higher ratios of sulfur to niobium pentoxide in the -~charere. In the present work, a detailed investigation on the calciothermic reduction of niobium pentoxide in a stainless-steel bomb in presence of sulfur as the heat booster was undertaken on a laboratory scale.

Jan 1, 1964

By D. T. MacRoberts

This paper embodies the results of theoretical studies concerning gas reservoirs, especially the effect of drilling programs of various intensities upon pressure depletion and ultimate recoveries. The primary objective has been to determine the net quantity of recoverable gas that could be obtained as a result of each additional well, in comparison with the gas . that might be secured from a single well ideally placed with respect to both acreage and geological structure. No method is yet known whereby the relative merits of intensive and sparse drilling can be compared experimentally; a reservoir must either be drilled closely or developed with wide spacing, but both programs cannot be conducted simultaneously. Hence, the analytical method seems to be the only approach to the problem. While the present state of our theoretical knowledge does not offer a precise solution to the problem of gas flow in sand bodies, it takes such appropriate cognizance of the limitations of the methods used as to restrict any answer obtained to the realm of engineering accuracy. In solving the problem for the average gas field, it was found that practically the same answers resulted as to pressure distribution, regardless of the size of the drainage radius, even though the latter was assumed to vary from a few feet as a minimum to that of the entire reservoir as a maximum. Such limits represent extreme possibilities; therefore, the practical conditions that are associated with normal development programs, in which wells are placed in the center of tracts varying in size from 40 to 640 acres, will of necessity result in less extreme variations than those indicated in the tables accompanying this paper. Stated more concisely, the amount of gas unrecovered at abandonment (of the particular field used for illustrative purposes) will lie somewhere between 4.6 and 6 per cent of the total original content, no matter how intensively the field is drilled. Gas reservoirs may be divided into two general types, those in which the energy is intrinsic, and those of which the energy is extrinsic. † The first type contains energy in the form of a compressed gas, which expands

Jan 1, 1938

By Ben L. Seegmiller

Roof, pillar and floor stability is a most important requirement in underground coal mines because it represents the leading cause of fatalities. In future coal mine planning the geotechnical aspects must often be minimized owing to unavailability of data. It is, therefore, very important to include a geotechnical investigation as part of the coal exploration program. Data which should be collected basically include the geological discontinuity characteristics, the rock strength characteristics and the groundwater aspects. Many times the only source of such data is the exploration boreholes. Therefore, an emphasis must be made to extract the maximum information from the core and the borehole. Data collection methods can include the preparation of detailed geotechnical logs for the roof, coal and floor. Laboratory strength testing will provide estimates of the mechanical properties of the various lithologic types. Slaking and swelling tests provide an insight into the stability characteristics of the rock materials immediately enclosing the coal seam. The boreholes may be used to provide permeability and pressurization data. Having developed a suitable geotechnical data base allows various stability prediction methods to be used. These include a geotechnical appraisal of the roof and floor units, depositional environment methods, multiple overlay techniques, hazard analysis techniques and classification/rating systems for roof and floor. The basic geotechnical data and the stability prediction methods form a basis upon which preliminary rock mechanics designs may be developed. Of particular importance to future coal mining are those designs relating to longwall mining because most companies are thinking in terms of the greater safety and greater productivity offered by longwalls. Items which should be ad- dressed when considering a longwall system include the panel layout in terms of a total mining plan, strata mechanics, roof/floor bearing capacities, face support requirements, face length, entry and pillar

Jan 1, 1983

By M. Van Siclen

THE outstanding fact in connection with dust disease in the United States at present is the growing recognition of its seriousness by state officials and by the more progressive operators of mining, metallurgical and allied industrial plants. The same may perhaps be said of labor in some of its better organized centers, but the average independent non-union workman continues, as of yore, to suffer the toll of disability and even of death from dust inhalation without realization of the source of his ill-being. Progress in the betterment of the handling of sufferers from dust disease and of the conditions creating dust hazards in mining and allied industries is pursuing a course similar to that of the now widespread campaign against accidents, in which the risk is more obvious, more severe, and was naturally recognized sooner. The coming on of dust disease is generally relatively slow and its immediate effects not infre¬quently masked by or attributed to other diseases. Marked exceptions to this general rule have occurred in districts where the dust is particularly pernicious, such as the Rand and Joplin; yet such exceptions, unhappy in themselves, opened the eyes of medical men, and of those in other localities charged with the responsibility for the welfare of industry, to the much more widespread if less spectacular hazard. existing from the inhalation of dust in all rock-excavating operations and all industrial operations creating inorganic dust, whether it be crushing and grinding, sand-blasting, granite-cutting, or what not. Advancement to date in the United States in prevention and treatment has been slow, yet the record shows that quantitative methods for determining the degree of hazard and means for decreasing it were being developed as far back as 25 years ago; and that more rapid progress may be looked for from now on. In 1908, in this country; F. L Hoffman?(1) discussed the mortality from consumption in dusty trades, especially brass foundries; and in 1913 E. R. Hayhurst(2) described the effects of inhalation

Jan 1, 1933

By John C. Draper

The principal object of an underground coal mine transportation system is to move coal from the face where it is produced to the outside of the mine where it is prepared for market. In addition to the movement of coal, a transportation system must also move supply materials to the inside; it must move men in and out of the mine; and it must move rock and other debris out of the mine for disposal. Usually, mine haulage is divided into three categories named for the various areas of the mine served : 1) Face Haulage. This is used at face from the mining machine to the intermediate transport system. 2) Intermediate or Secondary Haulage. Generally this is used between face haulage and main haulage. Sometimes this is merely an extension of the main haulage. 3) Main Haulage. This extends from the secondary haulage to the outside and is usually either a track or conveyor system, sometimes a combination of both. Transportation modes of coal in the various areas pose different problems, but the whole system must be synchronized. For instance, at the face the coal should be removed quickly from the various places to facilitate the movement of machines, whereas the intermediate system just passes the same coal on to the main transportation system. Selection of the transportation system must be based on the seam height, mining methods used to extract the coal, capacity required, ease of coal handling, and haulage efficiency. When driving rooms, mine cars can be used. They often simplify supply haulage and rock handling because they can also handle these items. Conveyors could be used and would have a greater haulage capacity but they cannot handle supplies easily or segregate the rock. When using a different mining method, such as longwall, mine cars cannot be used because there is not sufficient space to move the cars at the face nor can the cars haul the coal without delays which would cause excessive losses in production. As for ease of handling

Jan 1, 1981

By James D. Reilly

13.1-1. Introduction. COAL RESERVES OF THE UNITED STATES. Bituminous coal is the most abundant fossil fuel in America. With reserves of 1,660 billion tons and assumed recovery of 5070, there is more than 830 billion tons of recoverable coal--enough to assure ample supplies of energy for centuries. Looking at Fig. 13.1-1, coal is found in a majority of the states, including [ ]

Jan 1, 1968

By W. H. Newhouse

During the past few years the writer has been impressed by the close relation of many epigenetic orebodies with anticlinal structures. In the literature on ore deposits there is occasional mention that an oreshoot or district is on an anticline, but in most of the descriptions no weight or significance is attached to the relation, and usually the fact is concealed in a mass of structural detail. A few writers have stressed the relationship in a few districts or on a certain type of deposit. Church, Spurr, Butler, Stahl and Schuette have called attention to certain features, but the general extent of such a correlation has not been made known in any publication that the author has seen. A recent article1 on the localization of ore deposits, by well-known geologists, does not consider this common association. The author has seen in the field a number of the structural features described, and in addition has made a fairly complete review of the literature. This paper presents enough of the examples found to show the frequency of the relation to anticlines, and since only a few deposits on synclines are known, all of these of any importance of which the writer knows are mentioned. With certain qualifications which are discussed later, epigenetic ore deposits of replacement or vein type are mostly found where local upwarps of the earth's crust have taken place. Where formations antedating the ore deposits are present in the proper attitude to demonstrate vertical warping (i. e., more or less horizontal beds) the structural feature on which a mineral district, or mineralized area is located is almost always anticlinal, or domelike in nature. Some or even most of the ore deposits in a given district may be on the flanks of the upwarp, but few major districts are located definitely on downwarped areas. Synclinal basins within certain limits of size appear to be unfavorable to the type of fracturing that admits ore-bearing solutions. Replacement orebodies frequently are localized in small anticlines or domes, the size of the anticline or roll often being more or less commensurate with that of the enclosed oreshoot. This feature certainly ranks

Jan 1, 1931

By R. Maddin, S. K. Tung

SUCCESS of the dislocation theory in formulating the transitional lattice theory proposed by Har-greaves and Hill in 1929' is well established for low angle grain boundaries. The theoretical work of Burgersa and Read and Shockley,3 together with the experimental observations of Aust and Chalmers4 and Parker and colleagues,6 leaves little doubt as to the structure of grain boundaries with differences of orientations up to between 15" and 20". Beyond these angles, the structure of the boundary is not so clear, and is still a matter for conjecture. There have been notable experiments devised from which the data could be used to calculate energetics for possible arrangements of atoms in forming a large angle boundary.6 Most of these experiments deal with diffusion through and along the grain boundary. The recent work of Rhines and Cochart7 and Rhines, Bond, and Kissel18 was concerned with the relative movement of grains in aluminum bicrystals under constant tensile loads with their boundaries aligned at 45 " to the tension axis. The gliding along the grain boundary was cyclic and began after an incubation period. The velocity of gliding increased with the sum of the angular difference, 8, between the operative slip direction in the conjugate crystals and the angular difference between the active slip planes as measured between their traces upon the grain boundary. The initial gliding rate varied with temperature, and the logarithm of the average gliding taken over a considerable period was a linear function of the reciprocal of the absolute temperature: the slope gave an activation energy of 11,000 ±1,000 cal per mole. Since the rate of grain boundary shear is sensitive to the misorientation of the grains themselves, as shown by several workers,7,8 it is suggested that further work of this type might be fruitful in adding information regarding the behavior of boundaries under stress. The techniques devised by Chalmers" added impetus to the facility for observing grain boundary behavior, in that they provided a simple means for producing bicrystals of predetermined orientation so that the angle of the boundary could be controlled,

Jan 1, 1958

By R. K. Datta

Eluropium -activated yttrium vanadate, excited by short- and long-wavelength ultraviolet radiations, shows enzission lines near 6100A, the principal ones correspondirzg to transitions of EU+3 ions from 5Do to the F2 energy level. The ~neclmlallistns of absorption and etnissiorz of this phosphor have been empirically studied. The absorption is caused by two separate processes in the matrix. The phosphor YVO4:Eu and tlie matrix YVO, haue essentially the same resectance spectra in the region 2500 to 4000if. There are two broat ah~o?~ption bands: natnely, around 2600 and 3600A regions. Whet? compared with the reflectance spectra of the constituent oxides, namely, Y2O3, V205, Eu2 03, the absorption bands of the tnatvix and the phosphor in the short- and long-wavelength ultraviolet regions can be interpreted as due to charge-transfer processes involving i) Y-O and ii) 17-0, respecti~~ely. The excitation spectrum' of the phosphor has two broad bands with peaks at about 2600 and 3600A regions. U can be postulated that enevgy absorbed under short- crud long-wavelength ultraziolet excitatzon, respectzcely, by Y-0 and V-O parts of the niatrix is transferred by radcatio~zless process to EU+3 ions. Thzs postulate can empirically be proved on the basis of the spectra of the systems (YVO4,-YPO4,):Eu. PO? ~ons do not have' any appreciable absorption in the short or long uv regions. When P0't3 ions are substitlited for v0i3 ions in YVO,:Eu phosphors, the absorption and excitation in the lo~zg uv region are gradually reduced. Ailoreover, the £«+3 emission under 3650A excitation is decreased zuitlz increase in PO^ content, lt~lzereas the emission under 253711 excitation remains esserztially constant with as IILUCIL as 60 mole pct of YPO, in YVO,:En. EUROPIUM-activated yttrium vanadate (YV04:Eu) is a well-known phosptor.'-3 When excited by cathode rays, 2537, or 3650A radiations, YV04:Eu emits typical narrow-band spectrum of EU'3 fluorescence in the region of 5900 to 7100A, a very strong maximum occurring at about 6190A. This emission is considered to be due to 5Do — 7F2 transition of excite: EU*3 in 4f state. Moreover, the emission under 3650A excitation increases with temperature markedly. Because of these properties, YV04:Eu phosphor finds wide application in industries, namely, in color television tube, laser, and high-pressure mercury-vapor lamps. It is the purpose of this paper 1) to present the empirical study of the mechanism of absorption and excitation of YV04:Eu phosphor by ultraviolet radiation, and 2) to offer an explanation for the process of emission. It should be mentioned that a theoretical discussion on the mechanism of absorption in terms of the crystal or ligand field theory is beyond the scope of this paper. Empirical studies presented here are based primarily on spectroscopic and crystal-chemical investigations. EXPERIMENTAL i) Preparation of Materials. The synthesis of vanadate phosphorinvolves preparation of (Yi-.tEuj^Oj, blending the mixed oxide with an oxidic compound of vanadium, such as V205 or NH4V03, and firing the mixture at about 1000°C for several hours when YVO4:Eu forms as a primary phase. (Y1-xEux)203 compositions are prepared by coprecipitation of oxalates, and igniting them at about 1000°C. The vanadium compound is added in excess of the stoichiometric proportion for fluxing purposes. The charge is cooled, ground, and the excess of vanadium is removed by a hot wash (-80°C) of alkali or ammonia. Y(VP)04:Eu samples are prepared by mixing (Yi-xEux)203 with stoichio-metric proportions of (NH4)2HP04 and the vanadium compound. The mixtures are prefired at 700" to 800°C for 1 or 2 hr, then ground and refired at 1150°C. The firings of the phosphors are done in silica crucibles, and the homogeneity of the final products checked by X-ray diffraction analysis. ii) Spectroscopic Measurements. Diffuse reflectance sqectra of the samples within the range 2500 to 7000A are obtained by using CaF2 as standard in Cary Recording Spectrophotometer, Model No. 14. The emission spectra from phosphor plaques, excited under different ultraviolet sources, are obtained by a direct-recording spectroradiometer4 adapted with a grating monochromator with nearly constant dispersion. Maximym sensitivity in the spectral region from 2500 to 7000A is obtained with a quartz-windowed, S-20 response p$otomultiplier. The total' band pass is kept about 30A. The spectra are calibrated against the light from a standard tungsten filament lamp reflected from a magnesium-oxide plaque. Brightness data given throughout this report $re measured from the height of the main peak (6190A) of the emission spectra. The excitation spectra are measured using sodium salicy-late as standard. RESULTS AND DISCUSSION The diffuse reflectance spectra of both pure and activated YV04, along with their constituent components, are shown in Fig. 1. YVO4 shows two broad absorption bands, namely, around 2500 and 3600A, respectively. Since there is little difference between the reflectance spectraoof YVO4 and YVO,:Eu in the uv region (2500 to 4000A), it can be postulated that excitation of the phosphor is mainly due to absorption by the matrix, i.e., YVO4. The question, now, is whether the matrix (Yv04) is excited as a whole, or different components are responsible for the two absorption bands. The characteristic absorption spectra of molecular ions involving transition metal ions, both in aqueous solutions and in crystals, are due to electronic transi-

Jan 1, 1968

By Wilhelm Borchers

In all special branches of the chemical and metallurgical industries, in which large electric furnaces became necessary for carrying out new processes or for the improvement of old ones, the development of the electric furnaces took place on much the same lines. The endeavors to make a success of a new idea brought forth many ingenious designs, which, however, almost without exception, furnished the proof that the safest and shortest way to practical success is the utmost simplicity of construction of the necessary apparatus. Our knowledge of the qualities of materials for building electric furnaces and of the constituents of the furnace-charges, especially their electric conductivity and their chemical affinity towards one another at high temperatures, is still far from being complete, and from this fact we must conclude that the smaller the number of elements in the construction of a furnace, the fewer the number of unreliable factors both in the construction and in the operation of the electric furnace. This conclusion deserves special attention when an electric furnace for making steel has to be chosen from the constantly-growing number of inventions, inasmuch as the chief constituent of steel, the element iron, is a substance which in its liquid phase has so great an affinity for those elemen'ts which are to be removed from the charge, that it is very difficult to comply with the following conditions: 1, to heat the refining-slag to the highest point of its chemical activity ; 2, to prevent the iron from entering the slag, or, where this cannot be done, to make it enter so that it finally appears in the end-product

Jan 1, 1911

By G. H. Kesler, C. E. Dryden, J. H. Oxley

Rates of heat- and mass-transfer from rods to recirculating air were determined within a one-quarter-scale model of a metals deposition bulb. The dependence of local and averaged rates of transfer upon outlet geometry, number of rods, position upon a rod, and airflow rate was established for flow patterns created by radial and tangential air inlets. The results are given a qualitative interpretation in terms of rates and distribution of metal deposition in a prototype deposition bulb. IT is well known that a number of metals can be prepared from volatile compounds containing them by causing dissociation of their compounds to occur at heated surfaces. Examples of such metals include silicon, titanium, zirconium, and aluminum, which can be prepared from their halides. While the ability to prepare high-purity metals by this technique is of importance in itself, the rate of deposition of metal also is important in considering the commercial potential of such a process. If the over-all process of deposition is broken down into separate steps of transport of materials to and from the heated deposition surface and establishment of chemical equilibrium at the surface, as was described in a recent paper,1 then since surface temperatures are usually high and surface equilibrium is attained very rapidly, the rate-controlling step can be considered as either that of transport of reactants to the surface or of transport of products other than deposited metal away from the surface. These two transport steps are related through the reaction stoichiometry. It can be shown1 that the rate and distribution of metal in such a transport-controlled process are determined by the over-all and local mass-transfer coefficients in conjunction with the equilibrium conversions at the hot surfaces. The rate relationship is: w = [KA(y a-y s)] B.E where the bracketed group is the rate of arrival of the reactant at the surface of area A as determined by the mole fraction driving force (y a - y s) and the convective transport constant K. The factor B is the weight fraction of metal in the reactant, and E is the equilibrium fractional conversion to metal. Numerical values of y, and y, are fixed by the vapor composition and the equilibrium compositim of reactant at the surface; and E can be determined by thermodynamic calculations or by experiment. However, values for the convective coefficient K are available generally only for systems of simple geometry, such as cross-flow past a rod or sphere or parallel flow past a flat plate or through a tube. Often it is necessary to work with systems of more complex geometry and in which the vapor flow may not be uniform or exactly parallel or perpendicular to the surface. It is possible, of course, to establish working correlations for these more complex systems by direct experiment; but the experiments usually are costly in both time and money. To circumvent this objection and to aid in arriving at an understanding of the relationships and interactions of the process variables, it is helpful to construct a model of the flow system in which air, water, or other convenient fluids can be substituted for the process vapors and with which mass-transfer measurements or analogous he at-transfer measurements can be made upon a simulated deposition surface. By this means, a large number of measurements can be made in a reasonable time, and the correlation of these results can be applied to the prototype system. Examples of the application of these techniques are to be found in the literature (e.g., Ref. 2). It is the purpose of this paper to illustrate these techniques by description of a model study which was done at Battelle Memorial Institute. The work to be described was of a preliminary nature; the investigation subsequently was extended to develop quantitative relationships among the significant dimensionless transport, geometric, and flow parameters. This more detailed study will be the subject of a future paper.

Jan 1, 1962

By F. E. Buch

THE Smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The Smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter ,aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pct moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pct oxide copper. The predominating minerals are chalcocite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating k bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. GENERAL DESCRIPTION Flotation concentrate, containing to pct moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1947

By Alan Morris

SEASON cracking of brass has received wide attention and there is a wealth of technical literature on the subject. Its causes are fairly well understood and means for its prevention are inexpensive and effective, .so that the frequency of failures from this source has diminished of recent years. But its sister phenomenon, the failure of annealed brass by reason of applied tensile stress plus a certain type of corrosion, has received less attention, though it has been responsible for occasional more or less troublesome cases of cracking of brass in service. The work described in the following pages was undertaken about two years ago to determine the relative resistance of various commercial brass mixtures to stress-corrosion cracking, and to learn something of the controlling factors. By stress-corrosion cracking we mean the cracking of brass free- from internal stresses by reason of applied tensile stress and simultaneous attack by certain corrosive agents. Rogers,1 in discussing a paper by Hatfield and Thirkell, says : "He had also applied a solution of mercuric salt to tensile test pieces of brass whilst they were under stress in the testing machine. At very moderate stresses such test pieces cracked, and very readily broke." Moore, Beckinsale and Mallinson2 subjected test pieces to simultane-us corrosion and tensile stress. In order to determine the minimum stress detectable in brass by the mercurous nitrate test, tensile samples were placed under stress and treated with mercurous nitrate solution. They found that brass stressed below a minimum did not crack.

Jan 1, 1930

By R. W. Raymond

Under the names of Conservation, Social Justice, the New Nationalism, and Progressive Democracy, many earnest reformers are calling for a new system of Federal government to replace the one which they ascribe to our fathers, and declare to have been outgrown. They are proposing the lease by the United States of certain natural resources on the public domain, for the profit of the U. S. Treasury, instead of the sale of such resources to private citizens or associations of citizens. In the present paper, I shall try to show that this notion is neither new nor good. It is clear that the United States is owner, as well as sovereign, of public lands acquired through conquest or purchase from other nations, as it was owner of the public lands expressly ceded to it by the original thirteen States. Its policy with regard to such lands involves, therefore, two entirely distinct questions: What shall it do as owner ? and, What shall it do as sovereign ? The latter question, it must be confessed, has played but a small part in our history. All the prerogatives of sovereignty which were not explicitly conferred upon the Federal government by the original States were retained by them. The ownership or control of precious or other metals or minerals in the earth, for instance, was thus reserved to the several sovereign States. New York, South Carolina, and other States have passed laws on this subject, without regard to Federal authority. As new States have been successively admitted to the Union, the tacitly accepted theory has been, that they thereby acquired all the reserved rights of the original States. These newer States largely outnumber the first thirteen; and it is inconceivable that they would submit to any deprivation of sovereignty based on historical grounds. One of them—Texas—came into the Union by its own voluntary

Jan 1, 1913

By Paul A. Flinn, Jean-Marie Robert Genin

The MCssbauer effect was used to study the distribution of carbon in Fe-C alloys of high carbon content during room-temperature aging. In freshly formed rnartensite the carbon distribution is approximately random; carbon clustering occurs dun'ng aging. In the retained austete the carbon atoms are isolated, suggesting an efiective repulsion; and no rearrangement during room-temperature aging is evident. The kinetics of the carbon clustering in martensite has been studied in detail at 0" . 10". and 20°C. The time and temperature dependence observed is sinzilar to that reported for a variety of other aging effects, such as resistance change, hardness increase, and recovery of internal friction. The stabilization of the martensite kransformation also appears to be related to the clustering effect. DESPITE extensive efforts since the early days of Reaumur, the mechanism which provides the strengthening of steel remains controversial in many cases for several reasons: 1) The structure of as-quenched martensite is not well-determined. 2) Experimental methods capable of distinguishing between various hardening mechanisms are not well-developed. 3) The temperature of formation of many low-alloy martensites is so high that the martensite formed during quenching may be already tempered to some extent before any observation. Among all the hardening phenomena, the most puzzling one occurs at room temperature, where no structural changes have been detected by the usual methods of X-ray diffraction or electron microscopy. However, a new and more sensitive technique became available with the discovery of the MBssbauer effect. This effect makes possible the detection of changes in the local environment of iron atoms in solid solution. It has been extensively used in the study of substitutional alloy systems, for example, Fe-Al,1 Fe-Si,2,3 Fe-Rh,4 and Fe-Ni.5 Making use of the possibility of obtaining new structural information, we undertook an investigation of the aging of high-carbon Fe-C martensite to follow the structural changes involved in the aging at room temperature. Preliminary results6 showed that a clustering of the carbon atoms occurs with time. A systematic study of the kinetics of the process showed a striking similarity to the kinetics of stabilization of the marten-sitic transformation, thus suggesting further investigation of the relationship. EXPERIMENTAL TECHNIQUE To eliminate difficulties with the aging of martensite prior to the first experimental measurements, we needed an alloy with an M, temperature not above room temperature. Other investigators7 were misled by results obtained on alloys which transformed above room temperature and underwent structural changes prior to the first Mossbauer measurements. Winchell and cohen8 dealt with this difficulty by using a third element, nickel, to depress the MS below room temperature. The presence of nickel did not seriously interfere with hardness or resistivity measurements, but it would complicate the interpretation of the Mossbauer data by increasing the variety of iron environments. We chose, therefore, to obtain the necessary lowering of the M, simply by increasing the carbon content. After the first quench to room temperature, our specimens are retained austenite, which we later quench into liquid nitrogen. The martensitic transformation takes place suddenly, so that the as-quenched condition of the samples is retained, since the temperature is low enough to prevent any carbon diffusion. A Massbauer spectrum at 77°K can be taken and analyzed; after an appropriate up-quenching to the aging temperature, a new Mossbauer measurement at 77°K can be made. Fig. 1 shows a typical cycle of experiments. The samples were foils 25 p thick of high-purity

Jan 1, 1969

By C. Harries

The mechanism of blasting and the effect that blasting has on rock properties including the generation of new cracks and the opening of existing joints is discussed and compared with changes in seismic velocities. .Knowing the extent of blast induced damage and the overall stable slope angle it is shown that it is possible to design blasting so as not to induce any damage behind the toe of the blast area. Practical methods of blasting to meet this criterion and the results of these blasts are then discussed.

Jan 1, 1983

Jan 10, 1951