Search Documents

By D. W. Lillie

It has been demonstrated that considerable bend ductility exists in bulk specimens of polycrystalline high-purity silicon. The possibility of hot-forming at 1200°C is suggested. EXCELLENT corrosion resistance in many media and low cross section for absorption of thermal neutrons (0.13 barn) would make silicon of interest to nuclear engineers were it not for extreme brittle-ness and the difficulty of fabrication by any reasonable means. The use of silicon for structural purposes also has been considered in view of its light weight and oxidation resistance. Johnson and Han-sen' have investigated the properties of silicon-base alloys and concluded that there was no way of making pure silicon or silicon-rich alloys ductile at room temperature. In view of reports of appreciable ductility in germanium single crystals above 550°C'." and some plastic deformation in single-crystal silicon above 900oC,' the present investigation was undertaken to define more precisely the limits of high-temperature ductility in pure silicon. After this investigation was begun torsion ductility in both germanium and silicon was reported by Greiner." Through the courtesy of F. H. Horn, a small bar of cast extra high-purity silicon was obtained and small bend specimens were made from it by careful machining and grinding. All of the reported tests results were obtained from samples from this bar (bar No. 1) and one other of similar source (bar No. 2). No complete analysis was obtained but, based on analysis of similar semi-conductor grade material, metallic impurities were under 0.01 pct total. Vacuum-fusion analysis for oxygen showed a value of 0.0018 2 0.0003 pct for the first bar tested and metallographic analysis showed no evidence of a second phase. Bend tests were carried out on an Instron tensile machine using a bend fixture with a 1 -in. span loaded at the center. Supporting and loading bars were 0.250 in. round and the load was applied by downward motion of the pulling crosshead of the machine. Specimen thickness and width were approximately 0.10 in. and % in. respectively. Loading rate was controlled by holding crosshead motion constant at 0.02 ipm. In some cases a smaller specimen was used on a 5/8-in. span with a 0.129-in.-diam loading bar. The entire bend fixture was surrounded by a hinged furnace and all heating was done in air atmosphere. Temperature measurement was made with thermocouples fastened directly to the bend fixture within less than 1 in. from the specimen. Autographic stress-strain curves were recorded during each test, and breaking load, total deflection, and plastic strain could be obtained from these curves. Stress was calculated from the beam formula S = 3PL/2bh2, where P is the load in pounds, L the span in inches, b the specimen width in inches, and h the specimen thickness in inches. This formula is strictly correct only in the elastic range but has been used to calculate a nominal stress for convenience in the plastic range. The stress given is the maximum stress in the specimen. Results The results of the complete series of tests are shown in Table I. The first group of tests (specimens Nos. 1-6) showed the beginning of plastic flow at a test temperature of 900°C, so two additional tests (Nos. 8 and 9) were made at 950°C on small-size specimens from bar No. 2. Specimen No. 8 was tested in the as-machined condition, and No. 9 was heat-treated in hydrogen at 1300°C for 2 hr, cooled to 1200°C and held 1 hr, cooled to 1000°C and held 1 hr, cooled to 900°C and held 1 hr, and finally cooled to a low temperature before removal from the hydrogen. It is apparent that the heat-treatment had a significant effect on yield strength and ductility. In addition, the magnitude of the yield point was conslderably reduced in the heat-treated specimen as is shown m Fig. 1 by tracings of the stress-strain curves. After obtaining a furnace capable of reaching higher temperatures specimens Nos. 10 to 13 were tested at 1100 and 1200°C. Strain rate was increased by up to a factor of 10 to see whether the ductility observed was excessively strain sensitive. Specimen NO. 10, strained at 0.02 ipm and 1100oC, was still bending at a deflection of 0.322 in. when the load rate was increased to 0.2 ipm, resulting in immediate

Jan 1, 1959

By Richard Hunt

BINGHAM has produced 6 per cent. of this country's copper. In total production, it ranks fourth among the copper camps of North America, the order being Butte, Michigan, Bisbee, and Bingham. In its annual production, it held that same rank until 1919, when its production was exceeded by the combined production of the Globe-Miami district of Arizona. Bingham has also been a lead camp of the first order. Utah ranks third among the lead-producing states, and its production comes largely from three camps which, in the order of their productivity, are: Bingham, Tintic, Park City. Bingham's silver production is important, but it does not rank high as a silver producer. Utah owes its rank as first among the silver-producing states to Tintic, a camp 40 miles due south of Bingham. The United States Mineral Resources reports a total production from Bingham for the period 1865-1920 having a gross value of $528,043,432. Bingham is on the eastern flank of the Oquirrh range 30 miles south-west of Salt Lake City, from which it can be reached in an hour by auto, or by the Denver & Rio Grande or the Bingham & Garfield railroads.. The automobile route is a paved road across the floor of Great Salt Lake Valley, through farming country. The Bingham & Garfield railway leaves the level of Great Salt Lake at the northern end of the Oquirrh range, and in 20 miles it climbs 2100 ft., and deposits the traveler upon a shelf cut in the side of Bingham Canyon below most of the mines, which are farther up Bingham Canyon and its tributary Carr Fork. Below lies the town, a narrow ribbon running for a couple of miles along the bottom of a canyon 2000 ft. deep-an almost impossible site for a community numbering, in prosperous times, 5000 to 7000 inhabitants drawn from all quarters of the globe. Up the canyon and down, and beneath the steep slopes nearby, and beneath the town itself, are the mining operations of over half a century.

Jan 3, 1924

By Paul M. Tyler, Herbert R. Mosley

Strategically situated in almost the heart of the leading fertilizer-consuming area of the United States, Tennessee long has ranked second only to Florida as a phosphate-producing state. Since 1932 its share of the national output of phosphate rock has increased steadily, and in 1937 its production mounted to an all-time record. More significant even than the increase in tonnage are the forward strides in technology. The Tennessee Valley Authority's research program has led to quasicommer-cia1 operations using hydroelectric power to manufacture concentrated phosphatic fertilizer that is used to further the farmer education program designed to streamline the fertilizer business and halt the appalling waste of farm land by soil erosion. Even more stimulating to chemically minded imaginations is the production of elemental phosphorus by a private company that not only has succeeded in extracting it from the phosphate rock in electric furnaces but actually has contrived to capture it and to transport it safely in tank cars. New values have been created for low-grade phosphate deposits, and the economic life of reserves has been lengthened while the waste of former years goes back into the mills for recovery of its values by modernized methods. Tennessee's phosphate-mining industry dates from the discovery of blue rock in Lewis County in December 1893. Its known reserves are of the order of 101,500,000 tons, which compares with the production of 825,099 tons in 1937; that is, 21 per cent of the phosphate-rock output of the whole nation. The total output reported from 1894 until July 1. 1938, was approximately 19,000,000 tons. Offcial estimates of reserves are overly conservative and evidence submitted before a joint Congressional committee in November 1938 places "probable" reserves at more than 6,000,000,000 tons.

Jan 1, 1942

By Herbert R. Mosley, Paul M. Tyler

Strategically situated in almost the heart of the leading fertilizer-consuming area of the United States, Tennessee long has ranked second only to Florida as a phosphate-producing state. Since 1932 its share of the national output of phosphate rock has increased steadily, and in 1937 its production mounted to an all-time record. More significant even than the increase in tonnage are the forward strides in technology. The Tennessee Valley Authority's research program has led to quasicommer-cia1 operations using hydroelectric power to manufacture concentrated phosphatic fertilizer that is used to further the farmer education program designed to streamline the fertilizer business and halt the appalling waste of farm land by soil erosion. Even more stimulating to chemically minded imaginations is the production of elemental phosphorus by a private company that not only has succeeded in extracting it from the phosphate rock in electric furnaces but actually has contrived to capture it and to transport it safely in tank cars. New values have been created for low-grade phosphate deposits, and the economic life of reserves has been lengthened while the waste of former years goes back into the mills for recovery of its values by modernized methods. Tennessee's phosphate-mining industry dates from the discovery of blue rock in Lewis County in December 1893. Its known reserves are of the order of 101,500,000 tons, which compares with the production of 825,099 tons in 1937; that is, 21 per cent of the phosphate-rock output of the whole nation. The total output reported from 1894 until July 1. 1938, was approximately 19,000,000 tons. Offcial estimates of reserves are overly conservative and evidence submitted before a joint Congressional committee in November 1938 places "probable" reserves at more than 6,000,000,000 tons.

Jan 1, 1942

By E. E. Malouf

Rapid depletion of the world's mineral deposits combined with the expanding demand for metals places great pressure on our ability to provide technologically and economically feasible processes to recover greater amounts of metals from progressively lower grade sources. Chemical mining is one area in which expanding research and development can provide new processes or refinements to existing ones. These new techniques could result in increased production of metals from materials now considered uneconomic to process by current technology. To mine by chemicals requires the interaction of such disciplines as hydrometallurgy, microbiology, chemistry (both organic and inorganic), fluid flow, mineralogy, geology, and of course, economics. One of the least understood areas but one which may end up being an essential part of any chemical mining process is microbiology, i.e., the role of microorganisms in altering minerals and metals in solution.

Jan 1, 1971

After a three-year period characterized by inflation, recession, depressed metal prices, lack of demand, enormous world inventories, and rapidly escalating costs, the Canadian mining industry is showing welcome signs of recovery. A rise in world metal prices and particularly strong demand for gold, uranium, and coal have stimulated the industry in early 1979. In this atmosphere of growing optimism, over 3000 mineral industry executives, economists, geologists, and mining and metallurgical engineers convened in Montreal, April 26-29, for Canada's largest mining convention, the Annual General Meeting of the Canadian Institute of Mining and Metallurgy.

Jan 6, 1979

By P. C. J. Gallagher

A number of recmt determinations for the ratio of extrinsic to intrinsic stacking fault energy in fcc solid solutions are examined. Some of these arise from incomplete analyses which can yield only approxi?nate values for the ratio. Reliable results, on the other hand, obtained using extrinsic-intrinsic fault pairs, show that the extrinsic and intrinsic fault energies are essentially equal in several materials. There is some reason to believe that this finding is of general applicability to fcc elements and alloys. A wide range of values has been obtained for the relative magnitudes of the extrinsic and intrinsic stacking fault energies (yext and yint, respectively) in recently published studies in a variety of materials. In contrast, Hirth and Lothe' using a central force model have shown that out to tenth nearest-neighbor interactions the perturbation in energy caused by both types of fault is the same. Although the model used is not completely valid in metals, there is nevertheless some indication that marked variations of yext/nnt should not be observed from one material to another. In early work in Cu-A1, Cu-Ge, Ni-Co, and stainless steel all the deformation faults observed in the electron microscope were found to be intrinsic in nature, which led to an attitude that the extrinsic fault energy must be considerably greater than the intrinsic. Extrinsic faulting arising from deformation has, however, more recently been directly observed in Au-4.8 at. pct n;~ Ag-6 at. pct Sn and Ag-8 at. pct sn; Ag-7.5 at. pct In and Ag-11.8 at. pct 1n;"' pure silwer and Ag-0.5 at. pct ~n;' and Cu-22 at. pct Zn, Cu-30 at. pct Zn, and Cu-7.5 at. pct ~1.l' Multilayer loops containing extrinsic faulting have also been observed in quenched aluminum." While peak asymmetries in X-ray faulting probability studies were generally attributed to the presence of twins,Lelel2 has recently reinterpreted earlier X-ray data in Ag-Sb alloysU in terms of the presence of extrinsic faulting. The determinations of yeXt/yint made from the above studies are shown in Table I, with a brief description of the techniques employed. A number of the methods utilized are deficient in one or more respects, and the reliability of the values listed will be discussed. ~ele'~ recognizes that his approximate determinations of yext/yint assumes equal numbers of extrin-sically and intrinsically faulted dislocations. It is well-known, however, that such an assumption is not at all justified since extrinsic faulting has but rarely been observed in samples studied in the electron microscope. The only conclusion that should be drawn from the X-ray results at present is that the total intrinsic scattering cross section (i.e., the product of the width of the intrinsically faulted dislocations with their density) is approximately ten times greater than for extrinsic faulting in these particular samples. An important point is that the relative magnitudes of the energies cannot be inferred from results of this type, unless the intrinsic and extrinsic faults form with equal ease. One must recognize that, although a formation barrier may restrict the amount of extrinsic faulting which occurs, this in no way implies that the extrinsic and intrinsic energies should be different. It is unlikely that a worthwhile estimate of the relative densities of extrinsically and intrinsically faulted dislocations can be made at the high deformations present in X-ray samples. ~oretto,'~ from a statistical argument applied to the nonobservation of extrinsically faulted tetrahedra out of a large sample, concluded that yeXt/yint could not be less than -4.5. However, the present author feels that a high-energy formation barrier as just supposed also explains this finding satisfactorily and that no conclusion can possibly be drawn concerning the actual extrinsic stacking fault energy. The same argument also serves to explain the fact that extrinsic faulting has been relatively little observed in the electron microscope. Extrinsic-intrinsic node pairs and isolated extrinsic nodes were first reported by Loretto~ and subsequently by Ives and Ruff,' Gallaher,' and Gallagher and Wash-burn.' Ives and Ruff' found a wide spread in the ratio of extrinsically to intrinsically faulted area in the node pairs they observed, and drew the very tentative conclusion that yeXt/yint 2 2. They recognized that a straightforward comparison of the size of the faulted areas could provide no more than a qualitative result without a theoretical analysis of the dislocation geometry associated with extrinsic faulting. A theoretical

Jan 1, 1969

By H. C. Gatos, J. T. A. Pollock

It is well known that the superconducting critical current densities of many alloy superconductors may be increased by cold working and in some cases further enhanced by a short heat treatment. This latter enhancement has been attributed to the redistribution of dislocations into cell-like networks' and to the precipitation of second phase particles,2'3 which act as flux pinning centers. In a manner analogous to dislocation pinning in precipitation hardening alloys,4 it is expected that here also a critical distribution of the pinning centers should result in maximum pinning effect. Concentration inhomogeneities exist in most or all commercial alloys yet there have been only a few attempts made to determine their effect on critical current capacity in the absence of cold working. Sutton and Baker,5 and Kramer and Rhodes6 have found that the complex precipitation processes occurring during the aging of Ti-Nb alloys can result in critical current density enhancement. Livingston7-10 has clearly shown, for lead and indium based alloys, that the distribution of precipitated second phase particles is of critical importance in determining magnetization characteristics. However, these '(soft" alloys age at room temperature and the time involved in specimen preparation prevents metallographic examination in the state in which the superconducting measurements are made. Thus results with such alloys are expected to be biased towards larger precipitates and interpar-ticle spacing. The present study of Ta-Zr alloys was undertaken to examine the influence of second phase precipitation, as controlled by heat treatment, on the critical current capacity of well annealed polycrystalline material. A study of the published phase diagram11 indicated that annealing supersaturated samples containing up to 9 at. pct Zr at suitable temperatures would result in the precipitation of a zirconium-rich second phase. It was MATERIALS AND PROCEDURE The alloys were prepared from spectrochemically pure tantalum and zirconium. Analysis was carried out by the supplier. Major impurities in the tantalum were: 12 pprn of 02, 17 pprn of N2, 19 pprn of C, and less than 10 ppm each of Mo, Nb, Al, Cr, Ni, Si, Ti. The crystal bar zirconium was pure except for the following concentrations: 15 pprn of 02, 17 ppm of C, 23 ppm of Fe, 11 ppm of Cu, and less than 10 pprn each of Al, Ca, N2, Ti, and Sn. Samples were prepared in the form of 8 to 10 g but-tons by arc melting using a nonconsumable electrode on a water-cooled copper hearth in a high purity ar-gon atmosphere. Each button was inverted and re-melted three times to ensure an even distribution of the component elements. The samples were then homogenized at temperatures close to their melting points for 3 days in a vacuum furnace maintained at 5 x 10-7 mm Hg. After this treatment the buttons were cold rolled to sheets approximately 0.020 in. thick from which specimens were cut, 0.040 in, wide and 1 in. long suitable for critical current density (J,) and critical temperature (T,) measurements. These strips were then recrystallized and further grain growth was allowed by an additional vacuum heat treatment at 1800°C for 60 hr. Some second phase precipitation occurred during cooling of the furnace and a solution treatment was necessary to produce single phase supersaturated samples. This treatment was successfully carried out by sealing the samples together with some zirconium chips in quartz tubes under a vacuum of 5 x 10-7 mm Hg, heating at 1000°C for 5 hr and then quenching into water or liquid nitrogen. The samples were then heat treated at either 350" or 550°C and quenched into water or liquid nitrogen. All samples which were heat treated at 350°C were quenched in both cases by cracking the capsules in liquid nitrogen. The samples treated at 550°C were quenched by dropping the capsules into water. Analysis for oxygen in randomly selected samples indicated that the oxygen content was in the range of 175 to 225 ppm. Values of Tc were determined by employing a self-inductance technique. Jc measurements were made at 4.2oK by increasing the direct current through the wire in a perpendicularly applied field until a voltage of 1 pv was detected with a null meter. The risk of resistive heating at the soldered joints during these latter measurements was reduced by first plating the ends of the wires with indium and then soldering to the copper current leads using tin. Metallographic examinations were performed after mechanical polishing of the same samples and etching in a 4H20:3HN03 (conc):lHF(conc) solution.

Jan 1, 1970

By R. M. Hays

At the present time, oxidized taconite and semitaconite are not processed on the Mesabi Range except in vely limited tonnages. However, it is estimated that by 1990 shipments from the Range will approach 75 million tons of iron ore per year. To achieve this and future production, either additional magnetic taconite reserves must be proven or oxidized taconite and semitaconite must be processed. One beneficiation process which uses high-intensity magnetic separation and flotation for concentrating oxidized taconite and semitaconite is described. Detailed metallurgical results are given and an economic evaluation of the process is presented with comparison to other processes. The results of the present study indicate that the high-intensity magnetic separation and flotation process appears nearer commercialization for the processing of Mesabi Range semitaconite. The disadvantages of the process are nearer solution and are being solved by well-defined programs. During the twentieth century, the Mesabi Range in northeastern Minnesota has been the main source of iron ore for American steel mills. The Mesabi Range, which is about 120 miles long and up to 3 miles wide, is the pre-glacial outcrop of a group of sedimentary iron-bearing rocks known as the Biwabik formation. The formation, which is 200 to 650 ft thick and dips 50 to 10° to the southeast, is divided into four stratigraphic units. From top to bottom, these are the Upper Slaty, Upper Cherty, Lower Slaty, and Lower Cherty. Since its deposition in Precambrian time, most of the original Biwabik formation has been subject to alteration. Thus, although the iron content of the original formation was quite uniform, major variations in mineral composition now occur both laterally along the length of the formation and vertically within its units. Details of the mineralogical variations in the Biwabik formation have been described by Wolff,' Gruner, 2 and White.3 The unaltered portion of the Biwabik formation includes the magnetite taconites which are being commercially processed by Reserve Mining, Erie Mining, Eveleth Taconite, National Steel, Butler Taconite, and U.S. Steel. These six operations have a capacity of 32 million tons of iron ore pellets per year and have produced approximately 170milion tons of pellets since 1956. Capacity for another 30 million tons of pellets per year is being considered by the industry for the next ten years. This increase will be obtained by constructing new plants and by expanding present operations. Thus, by ! 978, it is estimated that approximately 60 million tons of iron ore vellets will be produced each vear from the magnetite taconites of the Biwabik formation. The portions of the Biwabik formation subjected to intense alteration resulted in direct shipping, wash, and heavy-media ores. Since 1892, 1.8 billion tons of direct shipping ore have been shipped from the Mesabi Range. This ore has been the major source of iron ore for American steel mills. In 1967, about 11 million tons of direct shipping ore and 13 million tons of wash, jig, heavy-media, and other gravity concentrates were shipped from the Mesabi Range.4 These products generally have poorer physical and chemical properties than the iron pellets produced from magnetic taconite. It is predicted that the shipment of these materials will decrease from 24 million tons in 1967 to 6 to 8 million tons in 1975.' This decrease will

Jan 1, 1970

There is mitigation for the sorrow of friends and the tragedy of sudden death when that death comes at the height of a successful career. It is not everyone's privilege to die, as has been the wish of many, in the harness—toiling, accomplishing, still necessary to the scheme of things. Nor is it everyone's privilege to leave a monument to his work. Dr. Fred Walter McNair died thus—in the midst of his work of educating, leaving along the path down the quarter century of his presidency of the Michigan College of Mines hundreds of men who, having come under his influence, have been successful in life.

Jan 1, 1924

By R. S. Shoemaker, F. W. McQuiston

In this Monograph are presented operating data, operating costs, plant descriptions, and detailed flowsheets of twenty seven different cyanidation plants around the world. Twenty three of these are gold producers and four are primarily silver producers. With one exception, (Pueblo Viejo scheduled to start up in late 1974), all of the plants are operating at the time of this writing. Selection of operations was based on metallurgy and were grouped into free milling lode ores, other free milling ores, ores requiring sulfide flotation in addition to cyanidation, ores requiring roasting, telluride ores, South African ores, and silver ores. Each of the plants described illustrates some unique form of cyanidation metallurgy. It is the hope of the authors that publication of this Monograph will be an aid to metallurgists in bringing new and successful cyanidation ventures into operation.

Jan 1, 1975

By Carl J. Christensen

This paper presents the development of diamond coring of the Weber sand section in the Rangely Field, Colorado. The description and operation of the diamond-coring equipment is included as well as the economics and results obtained by its use. Diamond coring is compared with the other methods used for drilling the Weber sand. Two types of diamond coring are discussed. The first and the one used most extensively is the regular 6 ?x 3¾-in. diamond bit and bottom hole 50-ft barrel. The second type, which has also been used successfully by Stanolind, consists of a 4 13/16 x 2 11/32-in. cutting bit and reverse circulation coring equipment. The first type will be referred to as regular or conventional diamond coring while the latter type will be referred to as reverse circulation diamond coring. Introduction Diamond coring has been used for many years in mines, quarries, surface coring at dam sites, laboratory work, and so on, but, until recently, had never been used very extensively in coring oil sands and other oil-bearing strata. It was demonstrated early in its development that hard forma-tions could be cut rapidly and that core recoveries far exceeded those obtained with conventional hard rock bits and quite often 100 pet recovery was obtained. However, the poorly constructed diamond-coring equipment and resulting high costs of early diamond coring slowed down its progress. Early in the development Of the Rangely Weber field, Rio Blanco County, Colorado, the Rangely Engineering Committee selected key wells that were to core the Weber section in its entirety. These cores were to be analyzed and various sections tested to gather sufficient information so that accurate reservoir studies could be made. The number of wells selected were kept at a minimum inasmuch as the productive Weber section, which is found at an approximate depth of 6000 ft, is thick, being as much as 600 to 700 ft on top of the structure. The Weber section is also comparatively hard to drill. For instance, one well took 60 days to core 490 ft of Weber sand with conventional coring equipment. It was noticed, however, that Core Labora-verse diamond plug cutter could quickly cut a plug from. one of these hard cores. This fact led to the serious consideration of diamond coring the Weber sand. The first diamond coring at Randy was performed by Stanolind in August 1946 andl although we experienced some difficulties, the results definitely indicated that diamond coring would be successful at Rangely for .coring the Weber sand. As more wells were cored and the equipment improved somewhat, diamond coring became less expensive than drilling the Weber sand with the conventional rock bit. In less than one Year diamond coring has definitely Proved its usefulness in oil-field drilling operations in the Rocky Mountain area where formations quite often drill very hard. The practice of spot coring in hard oil-bearing formations with conventional coring equipment is giving way diaimond coring of the entire sections, thus givng an operator the complete picture.

Jan 1, 1948

By Carl J. Christensen

This paper presents the development of diamond coring of the Weber sand section in the Rangely Field, Colorado. The description and operation of the diamond-coring equipment is included as well as the economics and results obtained by its use. Diamond coring is compared with the other methods used for drilling the Weber sand. Two types of diamond coring are discussed. The first and the one used most extensively is the regular 6 ?x 3¾-in. diamond bit and bottom hole 50-ft barrel. The second type, which has also been used successfully by Stanolind, consists of a 4 13/16 x 2 11/32-in. cutting bit and reverse circulation coring equipment. The first type will be referred to as regular or conventional diamond coring while the latter type will be referred to as reverse circulation diamond coring. Introduction Diamond coring has been used for many years in mines, quarries, surface coring at dam sites, laboratory work, and so on, but, until recently, had never been used very extensively in coring oil sands and other oil-bearing strata. It was demonstrated early in its development that hard forma-tions could be cut rapidly and that core recoveries far exceeded those obtained with conventional hard rock bits and quite often 100 pet recovery was obtained. However, the poorly constructed diamond-coring equipment and resulting high costs of early diamond coring slowed down its progress. Early in the development Of the Rangely Weber field, Rio Blanco County, Colorado, the Rangely Engineering Committee selected key wells that were to core the Weber section in its entirety. These cores were to be analyzed and various sections tested to gather sufficient information so that accurate reservoir studies could be made. The number of wells selected were kept at a minimum inasmuch as the productive Weber section, which is found at an approximate depth of 6000 ft, is thick, being as much as 600 to 700 ft on top of the structure. The Weber section is also comparatively hard to drill. For instance, one well took 60 days to core 490 ft of Weber sand with conventional coring equipment. It was noticed, however, that Core Labora-verse diamond plug cutter could quickly cut a plug from. one of these hard cores. This fact led to the serious consideration of diamond coring the Weber sand. The first diamond coring at Randy was performed by Stanolind in August 1946 andl although we experienced some difficulties, the results definitely indicated that diamond coring would be successful at Rangely for .coring the Weber sand. As more wells were cored and the equipment improved somewhat, diamond coring became less expensive than drilling the Weber sand with the conventional rock bit. In less than one Year diamond coring has definitely Proved its usefulness in oil-field drilling operations in the Rocky Mountain area where formations quite often drill very hard. The practice of spot coring in hard oil-bearing formations with conventional coring equipment is giving way diaimond coring of the entire sections, thus givng an operator the complete picture.

Jan 1, 1948

By D. P. Koistinen, K. E. Beu

THE application of the integrated intensity X-ray diffraction method to the measurement of retained austenite concentrations in hardened steels has been fully described.'-' In developing this particular method, the assumption was made that the samples used would have flat surfaces which were free from voids and in which austenite was homogeneously distributed. The original calculation procedure' was modified to include the constant factor G which relates the intensity of a given diffraction line to the concentration of the component giving rise to that line. In order to include A (0) in the constant factor G, it was further assumed that the geometrical conditions relating the X-ray beam, camera cylinder, and sample surface were precisely met.V has been demonstrated that these geometrical conditions can be met experimentally without difficulty in many cases;' however, for those samples which have irregular surfaces or where it is impossible to locate the sample in the proper position with respect to the X-ray beam and film cylinder, it is desirable to evaluate experimentally what effect these nonideal conditions have on the reliability of the austenite determination. This note decribes the results of such experiments. SAE 1095 bar stock was used throughout and all samples were heat-treated as follows: 1600°F for 1 hr in a neutral atmosphere, brine quench, and 300°F temper for 30 min. To control heat-treatment conditions as closely as possible, all samples were plated with 0.002 in. copper to protect the immediate surface from the heat-treating atmosphere. After heat treating, the samples were deplated electroly-tically so that only the copper was removed. The heat-treated surfaces thus obtained were nearly as bright and polished as the original surfaces before copper plating although no mechanical work was done on the samples after heat treating.

Jan 1, 1954

By M. E. Tyrrell, Alan H. Goode

The application of a simple, two-dimensional computer technique for evaluating rock burst potential in cut-and-fill stopes was investigated. The principal purpose of the study was to compare the effectiveness of high-modulus fill and destressing as aids in the control of rock bursts. Two conclusions that are probably of general applicability are drawn. First, high-modulus fill is ineffective as a means of increasing the mine stiffness and acts to control rock bursts only if it supports enough load to reduce substantially the stresses on the unmined vein material. Second, destressing is most effective if it is performed when the vein material is near the point of failure.

Jan 1, 1975

By S. Tandanand, Powell. L. R.

The US Bureau of Mines assessed the geological effects on the ratio of maximum subsidence and extraction thickness, known as the subsidence factor, to develop a simple method for predicting the maximum subsidence. The study is restricted to the Northern Appalachian Coal Basin where data were collected from 13 coal mines. A model previously developed to relate the subsidence factor with the lithology and with the width and depth of working panels was used in the assessment. The result shows the possibility of determining maximum subsidence without resorting to a rigorous method.

Jan 1, 1985

By H. S. Strouth

JAMAICA-bauxite and gypsum-but what else? J Does the Caribbean island have anything more to offer in the form of mineral wealth? One answer may be iron ore deposits which show enough promise to warrant exploitation in the near future by a company associated with Standard Ore & Alloys Corp. In addition, Jamaica is reported to have gold, silver, platinum, copper, lead, zinc, manganese, cobalt, and a great many nonmetallic minerals. Of these, only platinum has not been produced commercially in the past. Right now, Jamaican bauxite is getting most of the publicity, but not too long ago other mining operations were in progress. Lack of proper interest, insufficient roads, and scarcity of venture capital forced those mining properties to suspend production.

Jan 7, 1954

By Byron S. Gottfried, Guan Qi Zhao, John W. Tierney

Equations for predicting the performance of vacuum filters and centrifuges used for coal dewatering are presented. These equations are the basis for a dewatering module which has recently been added to the Coal Preparation Plant Simulator developed at the University of Pittsburgh under the sponsorship of the Department of Energy. The module provides for mechanical degradation in the centrifuge; loss of fines to centrate or filtrate; changes in size and gravity distribution; changes in ash and sulfur content; as well as final moisture content of the dewatered product. Inputs to the module are the flow rate of the coal to be dewatered, a washability analysis of the coal, and parameters describing the operation of the vacuum filter or centrifuge. Typical results obtained using the module are presented. There are adjustable parameters which can be varied to match plant operation or experimental data if desired.

Jan 1, 1983

By Rixford A. Beals

It has been observed with considerable accuracy that if the major U. S. mines were moved to Mexico tomorrow, many of them would be losing money. But the companies would continue to operate, losses or not, because they would have to. And some of the newest and most promising low grade ore projects in the U. S. would never have "gotten off the ground" had they faced the equivalent of the mining taxes now in effect in Mexico. No one of the various mining taxes in Mexico seems prohibitive by itself. Taken together, on the balance sheet, however, the picture changes. Production and export taxes alone take from 20 to 40 pct of the gross product value for base and precious metals.

Jan 2, 1955

By A. B. Young

In the original design of the flue system, the flues from the roasters delivered their gases to a large brick dust chamber which discharged into another flue with stack connection, as shown in Fig. 1. The treater is so situated that the gases are taken by it directly from the chamber and discharged again into the flue. The complete installation comprises two treater units, only one of which has been installed at present. The treater is essentially a flue 1.0 ft. high, 12 ft. wide, and 61 ft. long. (3 by 3.6 by 18.5 m.). Suspended inside, vertically and running lengthwise, are four banks of No. 20 corrugated iron plates; each bank is 10 ft. long, making an effective treater length of 40 ft. The spacing from center to center of the rows of plat,es is 9 1/8 in. (23 cm.) giving six-

Jan 1, 1921