Search Documents

By R. L. Robinson, P. DeFrank, R. F. Hatfield

Production equal to or greater than open-hole completions is possible through perforated completions if the flow paths throughout the perforations are free of obstructions.' Previous investigations have indicated that, in some cases, maximum productivity is not obtained due to plugging of the perforations with debris from the wellbore fluid and/or debris from the perforating process. Control of wellbore fluid and proper well completion techniques are very important in the elimination of perforation plugging.' Selection of properly designed perforating equipment also is quite important for maximum well productivity. Studies made with the use of the perforation flow laboratory, in which perforating tests are run under simulated well conditions, have shown that perforation plugging occasionally occurs. Plugs in perforations result from various causes. One of the contributors to plugging that can be controlled by the perforating device is the slug or carrot resulting from jet perforating. This condition has undergone extensive study, and previous developments have resulted in a decrease in carrot size—but not in complete elimination. It was felt that, if a method of completely eliminating the carrot could be found (with charge performance equal or better than previously obtained), a significant contribution would have been made. Such a charge has been developed and is reviewed in this paper. THEORETICAL CONSIDERATIONS OF CARROT ELIMINATION There are several popular theories of how a shaped charge jet is formed."," One of these is the hydrodynamic theory, wherein the liner is treated as a fluid under the impact of the explosive forces. Another is the spalling theory, where the interaction of shock waves in the liner causes small particles to be torn from the inner surface of the liner and projected at high velocity toward a common focal line to form the jet. It is not unreasonable to assume that both of these theories may be partially correct. For purposes of our discussion, it is simpler to use the second theory. Generally speaking, when a plate of metal is attacked by an explosive shock pulse, the pulse is transmitted through the metal at high velocity, as shown in Fig. 1(A). Pressures at the shock front may be 6 X 10' psi or higher. This shock wave (a compression wave) upon striking a free surface, Fig. 1(B), is partially reflected back as a tension wave. The interaction of the tension wave with the decaying compression wave causes a stress concentration in the metal; when this stress becomes great enough, a failure occurs and a small particle flies off and is projected away from the metal surface, as shown in Fig. 1(C). A new free surface is then presented to the shocks; the process repeats itself until there is no longer enough energy to cause failure, leaving a portion of the metal relativcly untouched. See Fig. 1(D). To apply this theory to a perforating shaped charge, consider the flat plate to be folded into a somewhat conical shape, with a column of explosive placed in intimate contact with the cone (Fig. 2). An explosive initiator detonates the charge, creating a shock wave

By Robert E. Green, Kenneth Reifsnider

A microscopic X-ray diffraction technique was employed for the simultaneous study of the behavior of several families of lattice planes, whose local orientatiotz changes are manufestations of internal distortions resulting from specimen deformation. Photographs taken using aluminum were single crystals 1/64 in. In diam are presented which illustrate the appearance of various types of deformation- or growth- induced structural variations. Slip and lattice bending were detected in tensile tests for strains as small as 0.1 pct. Evidence of deformation bands, lineage structure, and void formation wns also shown. AmONG the most important methods of studying internal stresses in metals is the utilization of various X-ray techniques. The general subject of X-ray metallography has been treated in a most excellent manner by Taylor,1 and the use of X-rays for the direct observation of imperfections in crystals has recently been reviewed in an article by Newkirk2 and in the book edited by Newkirk and Wernick.3 Since the inception of metallographic X-ray analysis, there have been numerous technological developments and refinements, each with its particular advantages and disadvantages and, acrording to these, its particular applications. X-ray diffraction techniques can be divided into two general categories, that of X-ray diffraction microscopy and that of X-ray diffraction macroscopy. In the former are included such methods as those of Berg-Barrett, Lang, and Schultz2,3 which are concerned with microscopic imperfections such as dislocations. The second category includes all work concerned with the study of the condition of a crystal lattice structure as indicated by the marroscopic detail in its diffraction patterns. An example of this is the study of the diffraction manifestations of inhomogeneous plastic deformation as manifested by formation of deformation bands and inhomogeneous lattice rotations. The method used in the present investigation was an X-ray diffraction macroscopy technique. The geometry and analytical aspects of the method were similar to those of Julien and Cullity.4,5 The source was collimated with a single slit in a manner simi- lar to the "parallel beam'' method of Barth and Hosemann6 except that a continuous spectrum of radiation was employed. The apparatus produced large-beam transmission Laue patterns of thin cylindrical aluminum-wire crystals, which were deformed either in tension or torsion. Although the conventional X-ray target and interposed slit were not capable of the high resolution obtainable with a fine-focus X-ray source as employed in a microfocus apparatus, resolution was a secondary consideration in our technique, and was sacrificed to obtain sufficient intensity along a sizable length of the specimen. By using a grid indexing technique similar to that of Barth,7 we were able to study several diffraction lines from various planes simultaneously. The results of these tests give additional information with regard to the inhomogeneous deformation of single crystals, and the indexing procedure used provides a correlation between portions of the test specimen and portions of a diffracted beam. EXPERIMENTAL TECHNIQUE The experimental arrangement used is shown schematically in Fig. 1. A source of continuous X radiation from a vertically mounted Machlett X-ray tube possessing a copper target and operated at 20 kv and 10 ma was passed down a horizontal lead tube 80 cm long which terminated in an adjustable vertical brass slit. The slit opening was adjusted to correspond with the diameter of the test specimen. In front of the brass slit it was possible to place a screen wire mesh, one horizontal strand of which was a lead wire which served as a fiduciary mark, the screen itself serving as an indexing system as will be described later. Behind the screen was the test specimen which consisted of an aluminum single crystal wire 1/64 in. in diameter and 3 in. long. These 3-in.-long crystals were cut from

Jan 1, 1965

By R. F. Steigerwald

The effects of heat transfer on the corrosion behavior of type 304 stainless steel in boiling water have been studied. Heat transfer conditions increase the tendencies of the stainless steel toward stress-corrosion mucking when the water is contaminated with Cl-. Surface preparation is the most important variable in determining the severity of the stress-corrosion problem in water with a given Cl- content. Heat treatment, chemical cleaning, and degree of wet film boiling also affect the corrosion of stainless steels used as heat transfer surfaces in boiling water. An up-paratus for corrosion testing under controlled heat transfer conditions is described. THE principal objective of this investigation was to study the corrosion behavior of AISI Type 304 stainless steel in boiling high-purity water under conditions of heat transfer. The principal variables in the study were: a) boiling conditions: limited boil, agitated boil; b) metallurgical structure: annealed or sensitized; c) surface condition: rolled, pickled, or ground. The results of the study should elucidate the role of heat transfer in the corrosion of stainless steel in boiling high-purity water and provide a base line from which to assess the severity of this type of corrosion. Although there has been an investigation of the effect of heat transfer on the corrosion behavior of stainless steels in alkaline waters,' work on the corrosion of stainless steels under heat transfer has been largely confined to various acid solutions.'-4 Furthermore, the study of the corrosion of stainless steels in high-purity water has been generally restricted to auto-clave and instream testing in superheated (e.g., 300°C) water and steam.5'6 Cooling water problems led to this study of the corrosion behavior of type 304 stainless steel in high-purity water at its atmospheric boiling point. In addition to the effects of heat transfer, this study also considered the influences of the type of boiling,7 metallurgical structure, and surface condition on the corrosion behavior of stainless steel in high-purity water. Two boiling conditions were investigated in this study: a) limiting boiling, i.e., when the heat-transfer surface had just reached the boiling point and boiling nucleated randomly over the specimen surface and b) agitated boiling, i.e., when a mild degree of superheat had been achieved on the specimen surface and boiling occurred generally over the specimen surface. Both boiling conditions are broadly classified as wet-film boiling. Originally, this program included the study of a third type of boiling, dry-film conditions. At dry-film boiling the temperature of the heat transfer surface is high enough so that it is covered with a continuous film of steam. Experimental difficulties made it impossible to study this kind of boiling with the available apparatus. Since surface condition affects heat transfer rates, three typical surfaces were chosen for study: a) as-rolled, the 2B finish received from the supplier, b) as-pickled, 30 min in 8 pct HNO3-1 pct HF, and c) as-ground on 120 grit paper. In order to evaluate the effect of improper heat treatment or welding on hot wall corrosion, both annealed and sensitized mi-crostructure were included in this study. EXPERIMENTAL Test Apparatus. The particular problems of interest in this investigation required a knowledge of the thermal gradient through the test specimen. From this gradient, the heat flux to the surface and the surface temperature could be determined. In order to satisfy this need, an apparatus similar to the boiling-disk apparatus of Fisher and whitney2 was designed. The solution is contained in a thermally-insulated, steel pipe lined with TEFLON resin. A stainless steel _______;________________________________________

Jan 1, 1970

• A new curriculum for combined liberal arts-engineering education has been announced by 6 middle western colleges. The plan involves three years of ;study at one of the 5 liberal arts colleges and two years and a summer of 'engineering work at Case; graduates receive both the A.B. and B.S. degrees. * A new kind of mining is being pioneered by a pest Virginia coal operator which enables four men to produce 800 tons of coal a day. The machine that makes this possible is a giant auger, 5 ft in diam and 100 ft long. Together with the carriage in which it is moved about, it weighs 60 tons. A mobile, but separate power plant of 1000 hp drives it. ' * The Sorel smelter, which will reduce Allard Lake titanium ores, will utilize five 6-electrode rectangular electric furnaces. Furnace hearth size will be about 18x50 ft, and the furnace will smelt about 300 tons of ore per day, producing 100 tons of iron and 130 tons of 70 pct Ti02 slag. The furnaces will be fed continuously by gravity from charge bins, and tap at intervals of 4 hr or more. Slag will be transferred to a high speed casting machine, using cast iron molds, then crushed for shipment to pigment producers. The iron will be treated to reduce its sulphur content to 0.03 to 0.05 pct, and then cast into small pigs or ingots for shipment to steel mills. • Flying of North Africa's first airborne mangetometer survey was completed this month, covering approximately 20,000 sq km in north central Tunisia for Gulf Exploration Co.'s program there. Mapping was completed in less than 30 days. •Yore than 9000 employees of 11 electric companies are enrolled in a 6-hr program that successfully informs workers on the principles of the American economic system. The course is given by the Middle West Service Co. which claims that before and after employee opinion polls show that the course instilled a better understanding of free enterprise and consequently a favorable response to it. •According to a report issued by the American Geological Institute there will be 2865 graduates in geology, including advanced degrees from U.S. colleges in 1950. This supply of geologists compares with requirements for 1278 at the professional and subprofessional levels. The report contains a detailed statistical study of the supply and demand situation for geologists in the 1949-50 period. •The dark cloud of over-production in the bituminous coal industry has a silver lining, according to Natural Resources Notes. Closing marginal mines, mostly strip and truck mines, will result in lower average costs and higher quality of the coal still produced. The producers that will then constitute the industry will be properly equipped and adequately financed to carry forward an intensive campaign to holdd and increase the markets for bituminous coal. •A light, compact, highly reliable blasting machine which does not rely for its effectiveness on the operator's skill is being tested by the Army Engineers. Operating under all climatic conditions from -65 to 125F, the 50-cap machine consists of a springwound do generator and is waterproof.

Jan 8, 1950

By J. C. Allen, E. V. Herring

CHILE EXPLORATION CO's. oxide plant at Chuquicamata, the largest of its kind, started in 1915 with initial operations at the rate of 10,000 tons of ore per day. Anaconda Copper Mining Co. acquired the controlling interest in 1923 and in the next few years modernized the plant and mine, extending operations to a nominal capacity of 490 million lb of electrolytic copper yearly by 1942. Plant production averaging 495.7 million lb of copper per year was maintained for the eight-year period extending from 1941 to 1948 inclusive. During the World War II production reached its highest level when in 1944 the output was 531.8 million lb. The maximum production for any one month was 49.6 million lb, achieved in May 1947. E. A. Cappelen Smith, consulting metallurgist for M. Guggenheim's Sons, worked out the first process for the treatment of Chuquicamata copper oxide ore about 1913, and directed a staff of 20 young engineers operating a pilot plant at Perth Amboy, N. J., on three shifts for an entire year. The copper is extracted from the oxide ore by a hydro-metallurgical treatment described in detail by T. A. Campbell in AIME Transactions, Vol. 106, Copper Metallurgy, 1933. The Oxide Plant is divided into five main operations as follows: (1) Crushing, (2) Leaching, including dechloridizing and sulphur dioxide treatment, (3) Tailing disposal, (4) Electrolytic precipitation, (5) Smelting and melting. Crushing The present Primary Crushing Plant has been in operation 25 years, during which time 4,342,112 cars of 70 tons net capacity have passed through the dumpers. The ore as received from the mine is frequently blocky and up to 5 feet in section. It is reduced to 9-in. size by two 60-in. gyratory crushers, and transported to the east and west ore bins by 60-in. conveyors. In the secondary crushing operation the ore is first reduced to 2 to 3-in. size by five standard 7-ft cone crushers and two No. 10 gyratories. This product is then reduced to 3/8-in. size by fifty-two 48-in. vertical Symons disc crushers and is transported by belt conveyors to the loading bridges from which it is charged° into the leaching vats. Conveyor belt No. 14 which serves the eight vats in the east section of the leaching plant has transported over 125 million tons of ore, which is a record for any type of conveyor. This 60-in. belt travels at a speed of 600 fpm and carries loads up to 5500 tons per hr. Leaching The ore is leached in 14 vats, averaging 13,500 short tons net capacity each. These vats are lined with a natural mastic which adequately resists the sulphuric acid leaching solutions. The leaching process as presently conducted comprises soaking the ore with successive volumes of leaching solution and spent electrolyte and withdrawing successive volumes of enriched solution from the vat to a total of approximately 3.2 million gal. The first 1.6 million gal of this volume withdrawn is called strong solution and contains about 35 parts of copper per 1000. The balance of 1.6 million gal subsequently withdrawn is stored in a

Jan 1, 1952

By Julian M. Avery

IN its dual role of pig-lion smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary purpose During the past 10 years or more, improvements in blast-furnace technique and economy have, n fact, been directed primarily to increasing efficiency n the use of the reducing power of the gases produced by combustion of coke at the tuyeres, to reduce iron ore within the furnace The net over-all result is a decrease n the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently amore than offset n value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements The purpose of the present paper is to suggest that, while progress has been made n this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all economy of a different order of magnitude than results thus far obtained by the use of other expedients The present argument is based in large part upon the hypothesis that the efficiency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss can be successfully attacked by increasing the over-all pressure, i e , the "top pressure" under which the furnace is operated It is indicated that pressure operation may also be expected to result n concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity In a broad sense, the suggestion of pressure operation of the pig-iron blast furnace is not new, for operation under moderately increased over-all pressure was suggested as early as 1871, by no less an authority than

Jan 1, 1938

By Sir Robert A. Hadfield

The Hadfield method of producing sound steel ingots has been the subject of a paper read before the Iron and Steel Institute, so that it will be unnecessary to describe it fully here. The object of the method is to make poseible the production of steel ingots in which the pipe is almost entirely obliterated, and it is applicable particularly to the production of sound ingots, from which good rails could be rolled. The method in brief consists in casting the ingots on cars, usually with the small end down. Each ingot mold is provided with a sand top, rammed up in the well-known manner. After the mold is filled to the desired height with steel, a layer of slag about 0.5 in. thick is placed upon it and the balance of the mold is then filled with charcoal. Then, through suitable piping, an air blast is directed in numerous jets upon the charcoal, which is burned thereby, the combustion supplying addi, tional heat to the top of the ingot, which helps to keep the top fluid and to retard its solidification, while the lower parts are rapidly losing heat by its transfer to the mold. By one plan the ingots are cast in molds placed upon bogies, movable trucks, or platforms, in the position A, Fig. 1. The ingots are cast vertically on bogies, say four or more ingots on each bogie, as may be found most convenient, and the upper surface of the steel is maintained in a molten condition during the transit of the ingots from the casting pit to the stripper. This is effected by a series of air pipes, for example, three in number, with jets or holes on the under surface of such pipes, placed preferably horizontally, arranged in such a manner as to cause jets of air to impinge on the upper surface of the ingots. These holes or jets are made throughout the entire length of the overhead pipes, the length of such pipes being

Jan 1, 1914

By H. H. Einstein

Swelling ground is one of the most feared problems in tunneling. Although usually not causing sudden failures during construction, the very large and longlasting deformations give contractors and designers the impression of facing an inevitable phenomenon against which there is no technical defense. Examples are concrete liners up to 1 m (3 ft) thickness that have been cracked or crushed, tunnel inverts that are heaving at 0.1 m (0.3 ft) per week during construction and continue to heave during decades. This paper summarizes essential components of design construction procedures where tunnels in swelling rock can be built to perform satisfactorily. It is important to point out that design and construction cannot and should not be separated. The way the tunnel will be built has to be an integral part of the design. Swelling can be defined as time dependent volume increase and is distinguished from squeezing, another time dependent phenomenon occurring in tunneling. Squeezing involves exceeding the shearing resistance while swelling usually does not. Swelling of rock masses can occur as swelling of the intact rock, swelling of wall rock, of gouge and of filler in the discontinuities of a rock mass, and as a combination of the above. Swelling mechanisms have been discussed elsewhere (ISRM 1983).

Jan 1, 1984

By Ian Campbell

THE year 1952 was marked by several new alltime highs in industrial mineral production; by an easing of the critical situation with respect such minerals as fluorspar and sulphur; by important production of asbestos, lithium, and rare earths; by the perfecting of new products which will place new demands upon industrial mineral supplies, such as "Fiberfrax", and the finding of new uses for old minerals, such as wollastonite; by continuation of basic and applied research; and publication of a notable study of the national mineral economy, viz., the "Paley Report".

Jan 2, 1953

By W. H. Emmons

A DIATREME is a hole blown through a rock by gases, presumably of volcanic origin. Not all pipes of ore have formed by deposition of metals in such openings, but a considerable number have so formed. In this paper are described peculiar vein patterns that are believed to be incipient diatremes or "perforation pipes." Grading into this group is one showing thorough brecciation without rotation of fragments and into the latter a group of ore pipes showing brecciation with rotation of fragments-many of them with well rounded fragments. Also, volcanic craters or volcanic necks are explosion pipes. These may carry ore deposits along their contacts and some carry deposits within the pipes. As new data appear this group becomes increasingly impressive. It has been shown that veins are concentrated in and about cupolas of batholiths and that such veins commonly lienearly parallel to the long axes of cupolas as these are shown on plans. It would be supposed that conical cupolas would have radial patterns, but few vein systems exhibit radial patterns. It is probable that explosion pipes also may form in areas above conical cupolas. From these the gases escape more violently because the loads above them are less than above an elongated cupola where larger bodies of rock are affected. The hypothesis is sound mechanically, for the top of an elongated cupola is a line whereas the top of a conical cupola is a point.

Jan 1, 1938

By M. R. Geer, Franklin T. Davis, H. F. Yancey

COKE with low phosphorus content is required by some of the electrometallurgical and chemical plants recently attracted to the Pacific Northwest by the hydroelectric power available from Bonneville and Grand Coulee dams. Shipping such coke into the area from eastern points involves a high freight charge, and during wartime consumes precious rail and ship-bottom space, so it is highly desirable to produce coke from the coking coals of Washington to meet the requirements of these industries. Although coke has been made from Washington coals since 1884, little has been known about their phosphorus contents or about the extent to which phosphorus could be reduced by cleaning. An investigation was undertaken, therefore, to determine the manner in which phosphorus occurs in the coking coals of Washington and its amenability to removal by ordinary coal-washing methods. PREVIOUS WORK Phosphorus is a deleterious element in coke used for numerous metallurgical processes, including the production of pig iron, yet comparatively little published information is available on the occurrence and elimination of phosphorus in any of the coals of this country. A variation from 0.009 to 0.062 per cent phosphorus in various horizons of the Pittsburgh bed in the Connellsville region of Pennsylania has been reported,1 and a reduction in phosphorus content from 0.020 per cent in the raw coal to 0.018 per cent in the washed coal was obtained in washing coal from the same bed in the Pittsburgh area;2 the latter figures represent average analyses for a year's operation of the washery on about 800,000 tons of coal. A reduction in phosphorus content from 0.018 to 0.011 per cent in washing coal from the Pittsburgh bed at another washery was observed, and the same report provides data on the phosphorus reduction obtained by separating 10 other coals on a bath of 1.35 specific gravity.3 European investigators have been especially active in correlating phosphorus content with petrographic analysis; fusain and durain generally contain the highest percentage of phosphorus, but this relationship is not universal.4 Some of these investigators have found that phosphorus is removed in the coal-washing process,5 but others have observed that the clean coal contained as much or even more phosphorus than the raw coal.6

Jan 1, 1944

By W. D. Robertson

A considerable quantity of experimental data is available on the effect of time, temperature, work-hardening and composition on the mechanical properties and corrosion resistance of aluminum alloys. There is, however, little unity of purpose or generality in most of the studies and, because the number of variables is large, the results often are not applicable to the problems that arise in practice. Furthermore, the customary expression of the effect of different variables as separate curves or as three-dimensional diagrams with time, temperature and the dependent variables as coordinates, renders the task of selecting the optimum time and temperature of precipitation treatment, with respect to their simultaneous but unequal effect on the various properties, exceedingly difficult. The introduction of precipitation treatments to raise the yield strength of 24S-type alloys has created a need for a method of correlating and summarizing the effect of time and temperature on the mechanical properties and susceptibility to intercrystalline corrosion. Correlation is particularly desirable because the choice of time and temperature is of necessity a compromise to achieve the best possible combination of properties, and the optimum conditions cannot be accurately specified unless the data are in a form in which the alternatives can be readily compared. Therefore, the work described here was undertaken to find a common relationship that would be capable of expressing the effect of precipitation time and temperature on the various properties and by means of which the relative effects could be correlated and their interpretation facilitated. REVIEW OF PREVIOUS WORK In connection with an investigation of the interrelation of age-hardening and creep performance of nickel-silicon-copper alloys, Jenkins and Bucknall1 demonstrated that the time required to attain maximum hardness and tensile strength could be expressed by a relationship of the form: t = K. 10m/T (I) where t is the time in hours and T the temperature of aging, expressed in degrees absolute, and m and K are constants. They also pointed out that this expression is analogous to that which describes the change of the diffusion coefficient D with temperature; namely, D = Ae-Q/RT (2) Later, Cohen used this relationship in studies of the mechanism of age-hardening of a silver- rich copper alloy2 and of duralumin. 3

Jan 1, 1945

By H. T. Matson, G. Allan Wallis

In the Northern Rhodesia copper fields the size of the orebodies and the exceptionally consistent values over great distances made it possible to outline the ore with drill holes spaced at 1000-ft. intervals; in some cases, 2000-ft. intervals. Owing to the fact that the size of the deposits made it very evident that much outside capital would have to be called in to develop them and, owing to the wide spacing of the holes, it was essential that the sampling of drill holes be as accurate as possible, so that outside examining engineers could adopt the results as trustworthy within the limits of accuracy of the drilling method. With this object in view, the field staffs of the Selection Trust group of companies have studied for the past three years, and are still studying, drill sampling in a very thorough manner, and for this reason it is felt that these notes may be of interest to engineers or students who are, or in the future may be, in charge of drilling operations. The orebodies in this field lie in shales and sandstones, more or less indurated, in the lower strata of the Roan series, and the copper mineralization is in the form of sulfides predominantly, with some oxidized copper minerals. These interested in the geology and history of the area can find full details in a recent paper by Anton Gray and Russell J. Parker.' In some formations core recovery was good—between 90 and 100 per cent.—and where any difficulty occurred in recovering sludge, as in fissured ground, this was not insisted upon; but the samplers' difficulties, both practical and theoretical, do not commence until core recovery drops and sludge recovery becomes important, for if core is being ground up it is recoverable only as sludge, and naturally the sludge sample, which theoretically should contain only the material cut from the annular ring around the core, is being salted, in a sense, by the ground-up core. In the perfect core, where 100 per cent. core is recovered as well as 100 per cent. sludge, the two samples can be treated separately, as in the case

Jan 1, 1931

By L. A. Willey

IN 1953, a method for filtering a liquid phase from solid phases while in equilibrium at elevated temperatures was devised at the Alcoa Aluminum Research Laboratories. Since then, it has been applied to the investigation of liquid-solid equilibrium in metallic systems. In application, the method simplifies the centrifuge filt.ration procedure as developed by Scheil and described by Gebhardt Fig. 1 shows a sketch of the filtering apparatus located within a thermal analysis furnace. It consists of a stainless steel filter crucible A, into the bottom of which a porous carbon filter disk B, 1 3/4 in. diam by 1/4 in. thick, is sealed to the shoulder and rim with carbonaceous cement. The base of the filter crucible, machined to an angle, fits into a tapered seat at the mouth of a stainless steel vacuum chamber C. A connecting tube from the vacuum chamber to a vacuum line also serves as a means for supporting the apparatus from the base of the furnace. An alundum crucible D of 25 ml capacity is placed with- in the vacuum chamber below the filter for collecting the filtrate. Two thermocouples E, in stainless steel protection tubes, which extend from 1/16 to in. above the center of the filter, are mounted on the rim of the filter crucible. One thermocouple is used in differential connection with the furnace control thermocouple to regulate rates of heating and cooling. The other serves as a means for recording the temperature of the alloy prior to filtering. A suitable mold coating is used on exposed surfaces of stainless steel parts to guard against attack upon these parts as well as to avoid contamination of the alloy samples. A mold wash prepared from precipitated CaCO, is suitable for aluminum alloys. The porous carbon for the filter disks and the carbonaceous cement, grade 200 (graphite base), were obtained from the National Carbon Co. Porous car-bon, grade Nos. 10 to 60, has been employed. Grade No. 40, however, appeared to give the optimum advantages in operation. In operation, an alloy sample is remelted and heated to about 50°C above its liquidus temperature. At the same time, the filter apparatus is preheated to about the same temperature. The alloy then is cast into the filter crucible.

Jan 1, 1957

By E. R. Kaiser

COAL research during 1942 was directed in an important degree toward the solution of problems of wartime importance. A wider selection of coals for carbonization to meet the increased demand for coke, and the improved utilization of lower-grade coals for boiler fuel were made possible by fundamental studies on cod and ash behavior that had been started several years ago. The coal industry's interest in the work of the various laboratories brightened significantly as results were demonstrated on smokeless combustion in stoves, on stokers without coke trees, and on pulverized firing of forge furnaces. Despite the limitations of priorities and scarcity of materials, the mineral industries building of the West Virginia University was completed and equipped with facilities for research on coal min

Jan 1, 1943

By Luis A. Fierino, M. Ashraf Mahtab

This paper reviews the background of, and solution techniques for, the major geomechanics problems affecting caving operations, including prediction of cavability, defining size distribution of or fragments, stability and support of production openings, and control of rock bursts and subsidence. Further research is also suggested in the solution of the various geomechanics problems.

Jan 1, 1984

By P. C. Upadhyay, J. G. Singh

Reissner's thick plate bending theory has been recast for rocks which exhibit the property of double elasticity: different Young's modulus and Poisson's ratio in compression and tension. The governing differential equation and other relevent expressions have been presented in a form compatible to the applied mechanics results so that they can readily be used. Effect of the ratio of Young's modulii in compression and tension, (Ec/Et), on the maximum plate deflection and the maximum bending moments has been evaluated over a wide range. It has been found that the inclusion of bi-modulus property through a parameter (ß = Ec/Et), changes the sheer deformation of the plate to such an extent that the bi-modular effect of rock cannot be overlooked in the thick plate analysis, especially when ß is expected to be greater than 2.

Jan 1, 1982

By L. E. Wilsey, W. G. Bearden

This paper presents results of analysis of the effect of fracturing on initial flow rates and on ultimate recoveries from low capacity oil formations. This analysis shows that even in formations of permeability as low as 0.1 md, large fracture treatments can yield oil recoveries and production rates approaching those of high permeability formations. Field production information is shown which supports the analytical work. INTRODUCTION Often hydrocarbon bearing formations are discovered which, while they are known to contain large quantities of oil, will not produce at commercially attractive rates without special well stimulation. Attempts to solve this problem led to the development of such techniques as underreaming, shooting, acidizing, and recently hydraulic fracturing. These methods of stimulation have been highly successful in many fields. All of these treatments, however, affect only the pay section near the well bore and therefore owe their success to circumventing and overcoming local permeability reduction about the well bore. It has been the belief that in treating wells to stimulate production in which there is no permeability reduction near the well, the maximum possible production rate increase would be of the order of two or fourfold. Hence, it has been concluded that fracture treatment of uniformly low capacity (permeability times thickness) formations could meet with but limited success. It is the purpose of this paper to show that the use of fracture treatments much larger than usually used can yield commercially attractive producing rates and high recoveries even in formations of permeability less than 0.1 of a md. PROCEDURE In order to illustrate the effects of fracturing, an analytical study of some hypothetical systems was made in which one factor at a time was varied to show what is important in recovering oil from fractured wells. It was assumed that a horizontal fracture of relatively high fluid-carrying capacity extended from a well bore. The presence of such a fracture will cause a marked influence on the flow pattern and pressure distribution in the formations, with the net effect being to reduce tremendously the resistance to flow into the well bore. A diagram of the resulting flow pattern and pressure distribution is illustrated in Fig. 1. Immediately after production commences, the principal flow of fluid is vertically from the formation flanking the fracture, into the fracture, and then into the well. After sufficient oil and gas have been produced to lower the pressure in the formation adjacent the fracture, oil and gas will begin to flow in a radial manner into the fracture from the formations beyond the end of the fracture. In calculating the performance under such conditions. the material balance or conservation of matter equation and equations of flow were solved simultaneously by a stepwise method of calculation. Flow rates were found by determining the pressure distribution, as illustrated

Jan 1, 1955

By Brison Robertson, W. P. Fishel

THE carbide-forming tendencies of the various steel-alloying elements, or their affinities for carbon, is a subject that has received considerable attention, but little more than a probable arrangement of the elements as to their carbide-forming tendencies has been proposed. The physical properties of alloy steels depend upon the relative proportions of the elements present and their combinations. One important phase of this subject is the distribution of carbon between the various elements present. The distribution of carbon between iron and other elements evidently will depend upon: (I) the affinity of each for carbon; (2) the relative atomic masses of the elements present; and (3) the possible formation of compounds between the alloying elements and iron and between the elements themselves. In ternary steels the case is simplified, especially in systems in which the element and iron form no compounds. In such systems iron and the alloying element are competing for the carbon present. In this work the distribution of carbon between titanium and iron has been studied by measuring the relative amounts of iron carbide and titanium carbide present in a series of annealed steels in which the ratio of titanium to carbon extended from 0.527 to 4.61. EXPERIMENTAL PROCEDURE Ten Fe-Ti-C alloys, weighing about 250 grams each, were prepared by melting under a vacuum, in an induction furnace, Armco iron, carbon-free ferrotitanium (25 per cent Ti), and pure carbon. Vacuum melting prevented the formation of titanium oxides and nitrides, which would complicate the problem. The melts were made in graphite crucibles lined with sintered magnesium oxide. The ingots were cooled in the furnace under a vacuum and were then completely annealed at 950°C. The determination of the amount of titanium carbide present was based upon the established insolubility of titanium carbide in boiling dilute (I :4) sulphuric acid, and the complete solubility of free titanium and titanium-iron compounds in this acid. High-carbon ferrotitanium, which had been treated to remove free Ti and Fe, was found to be completely insoluble in the acid; and the carbon-free ferrotitanium used in making the alloys was found to be completely soluble. Others 1,2 have reported the insolubility of titanium carbide in sulphuric and hydrochloric acids. Turnings from the ingots were digested with boiling sulphuric acid (1:4) until all action had ceased. The carbide residue was filtered off and analyzed for titanium, and in some cases for carbon. This represents the titanium that was united with carbon. The filtrate from the carbide residue contains the portion of the titanium that wasin solid solution in the ferrite. Titanium

Jan 1, 1944

By F. S. McNicholas

IN the first big blast at Climax, a "loop back" (three-wire system) was used (Fig. I), with the idea of securing a wiring system that would give to all series the same amount of current. Single-phase, 60-cycle, 13,800-volt [ ] power was furnished to the blasting transformers, each of which has a rated capacity of 600 amp. at 480 volts. Two blasting leads were taken from these transformers, giving a blasting current of single phase, 60 cycle, 480 volts, with an instantaneous capacity of more than 600 amp. The blasting switch was on the secondary leads from the transformers, to avoid lag in energizing them.

Jan 1, 1938