Search Documents

By D. A. Thomas, E. S. Meieran

Tungsten wires were examined by transmission electron microscopy after drawing and after high-temperature annealing. Drawn wire consists of highly elongated grains called fibers, whose long axis is parallel to [110]. Each fiber is ribbon-shaped, with the wide dimension of the ribbon parallel to (001) and the narrow dimension parallel to (110). Furthermore, most fibers are bent about [I10] and twisted along their length. The fibers are divided into cells, which in some cases contain a platelet substructure lying on (110) planes. The misorien-tations of these platelets accumulate to allow the macroscopic twist of the fibers. During annealing, several competing reactions occur, starting at different temperatures and progressing at different rates. Among these processes are fiber-boz~ndary migration, polygonization, dislocation rearrangement, and possibly impurity segregation. The fiber-boundary migration accompanied by the formation of transverse boundaries during polygonization leads to an equiaxed grain structure although recrystal-lization does not occur. There is a relationship between the flow stress of the wires and their average subgrain width in the form sy = s0 + kyd-1/2 . Also, there appears to be a relatio'nship between wire ductility and the formation of transverse boundaries during annealing at about 800°C. THERE have been many investigations of the structures and properties of tungsten wires1-4 due to their commercial importance for use as lamp filaments. The structural studies have so far been limited to optical microscope and replica electron-microscope studies. due to the difficulty of .-me- paring from wires thin foils which can be examined by transmission electron microscopy. However, this difficulty has been recently overcome,5 and it is now possible to examine tungsten wires by transmission electron microscopy as well as by other techniques. In this paper, the structure of drawn tungsten wire is described, as are the changes in the structure during high-temperature annealing. Some discussion of the relationship between structures and properties is also given. EXPERIMENTAL MATERIALS AND PROCEDURES Commercial 0.030-in.-diam doped tungsten wires drawn at progressively decreasing temperatures between about 1400° and about 800°C were examined. The composition, mechanical properties, and optical microstructures are described in detail elsewhere.' All experimental materials were vacuum-annealed for 10 ot 30 min at temperatures at 100°C intervals between 700° and 2000°C. Specimens were thinned for examination in the Siemens Elmiskop I electron microscope by the method of Meieran and Thomas.5 STRUCTURE OF AS-DRAWN WIRE The optical microstructure of as-drawn tungsten wire has been described by Peck and Thomas.7 They observed that wire in longitudinal section consists of highly elongated grains called fibers whose width varies between 1 and 10 µ, while in transverse section the fibers appear to be elliptical in cross section and bent about their common [110] wire axis. They explained this unusual appearance as being due to the drawing of a bcc material with a [110] texture, and predicted that the wide and narrow planes of the fiber cross section would be parallel to (001) and (110), respectively. The fibers apparently bend about the [110] axis during drawing to maintain grain boundary continuity during drawing. Transmission electron microscopy offers a way of checking these predictions as well as providing a more detailed picture of the wire structure. Figs. 1, 2, and 3 are typical electron micrographs of

Jan 1, 1965

John Duer Irving, who left his post as Professor of Economic Geology at the Sheffield Scientific School, New Haven, Conn., to join the Eleventh Regiment of Engineers shortly after the declaration of war, died in France, July 26, 1918, from an attack of pneumonia. Through the initiative of Mr. Benjamin B. Lawrence, a memorial service to Captain Irving was held at St. Paul's Chapel, Columbia University, on Sunday afternoon, August 4, which was' attended by members of Captain Irving's family, and about four hundred of his friends from Columbia, Yale, the American Institute of Mining Engineers and the Association of the 11th Regiment of Engineers. Professor James F. Kemp delivered the memorial address, and has prepared for the Institute the following account of Captain Irving's life, Professor Kemp and Captain Irving having been associated on the most intimate terms for a number of years. , The war has brought home to friends and kin in the western shores of thc Atlantic many losses whose suddenness has the shock of a blow. Many more will follow, but none can leave a sharper sense of regret than the news that the keen and productive mind; the inspiring teacher; the successful and considerate editor, the fine, true man and friend had all passed away when John Duer Irving made the final great gift to the service of his country, in the cause of decency and right. In the closing days of July, the cable brought the tidings that toward midnight on the twentieth of the month pneumonia had proved too great a tax upon one already worn by excessive labors. John Duer Irving was born in Madison, Wis., August 18, 1874. His father, Roland Duer Irving, was at the time professor of geology, mineralogy and metallurgy in the State University of Wisconsin.' Roland . Irving, the father, had entered Columbia College in 1863, but trouble with his eyes compelled him to suspend his studies in the classical course in his sophomore year, and to replace study with some months of life and travel in England. Ultimately his eyes became stronger, and he entered the School of Mincs, completing the course for the degree of Engineer of Mines in 1869, with the third class graduated. The class of eleven contained other future geologists. It numbered on its roll Henry Newton and Walter P. Jenney of the early survey of the Black Hills, where John, future son of Roland, was in the course of years to make his doctor's dissertation, and with its publication his really serious entrance into the profession. Roland Irving was a favorite student of Professor J. S. Newberry, affectionately known to all of his students as "Uncle John," and after some experience in mining and smelting in Pennsylvania and New Jersey, joined the Ohio Survey under Dr. Newberry. The work in Ohio was largely performed during the vacations of the University of Wisconsin, to whose chair Roland Irving was called in 1870. Later, his residence in Wisconsin led to two events of prime importance in the history of American geology. He began the study of the Gogebic iron range and caught the clue to the origin and stratigraphy of the iron ores of all the Lake Superior ranges; and he later undertook the mapping and description of the copper-bearing rocks of the Lake Superior basin. The formative years of the son, John, were passed in a home where the father.

Jan 1, 1920

By G. R. Gardner, D. H. Davis

INCREASING realization of the importance of dust control, and the recommendations of various agencies, have led the mining industry to become actively concerned with this problem. The background and necessity for adequate dust-suppression measures have been discussed in a number of publications, including those of the U. S. Bureau of Mines, and the use of spray water to reduce dust at the face and on roadways has been recommended. The problem resolves itself into obtaining adequate dust reduction at a reasonable cost. Inasmuch as the term "adequate dust suppression" has never been clearly defined, nor have permissible limits of dustiness (in terms of dust count) been established, it is apparent that any method selected may be required to meet additional demands. Until the industry has been given some indication of permissible limits of dustiness, no permanent solution is possible. Progress will be somewhat handicapped until such information is available. In addition, dust reduction must be obtained without the addition of any excessive moisture to the coal, since consideration must often be given to: I. Quality standards, particularly reduction in heat value. 2. Handling characteristics, particularly in regard to unloading from railroad cars and bins. 3. Application of dry methods of coal cleaning. 4. Necessity for fine screening within specified limits of oversize and undersize. Little detailed information is available as to the advantages and disadvantages of the several methods of water distribution, the location and protection of sprays, operating data on pressure, quantity of water, and so forth, and results obtained. In 1940 an investigation was undertaken to determine and evaluate the principal factors involved. This paper constitutes a progress report on this work and cannot in any way be regarded as complete on any one of the several phases. CLASSIFICATION OF DUST SOURCES The various sources of underground dust may be classified as primary or secondary. A primary source is one associated with appreciable degradation of size, that is, where the greater part of the actual fines capable of becoming air-borne dust are produced. A secondary source may be considered as one in which the greater part of the fines have been produced at some previous operation and are in such condition that they can be dispersed as air-borne dust. These conceptions appear to be of practical significance, as experience indicates that when dust is controlled at the primary sources the importance of secondary sources is minimized. For these reasons, investigations to date have been concerned principally with the primary sources of dust, and this paper is concerned particularly with one of these-namely, undercutting. In accord with the foregoing definitions, the sources to which the following opera-

Jan 1, 1942

By N. Marusov, D. K. Lowe, J. C. Karp

This paper considers, from an engineering viewpoint, several factors involved in creating, designing and locating horizontal barriers for controlling water coning. This is an effort to consolidate new concepts with previous information so that a reasonable selection of barrier materials, dimensions and vertical position can be made. Coning theories previously developed are briefly reviewed and an effort i,s made to reduce the results of coning-theory calculations to a point where routine calculations can be made with a desk calculator. It is expected that these simplified calculations will give usable predictions of the amounts of improvement attainable with barriers of various dimensions. Apparatus and procedures used for testing the suitability of commercial cements are described and test results are presented. INTRODUCTION Just about as soon as the phenomenon of water coning was recognized as an oilfield problem, there were suggestions that the production of water coning could be controlled or completely suppressed by means of horizontal barriers. It was also suggested that natural barriers such as shale streaks were helpful in restricting bottom-water production. The implication was that wells not having the benefit of continuous shale streaks to suppress bottom waters should, in some way, be supplied with an artificial barrier. With regard to the selection of barrier materials, there are many references which give the merits of liquid barriers.',' These liquids include surface-active agents," recipitates' and emu1sions. There is no real need to review the merits of these materials again. This paper deals with the use of solid barriers which could be made from various cements. The two major restrictions placed on these barrier cements are that (1) they must be commercially available in large quantities, and (2) they must be applicable by means of standard tools and equipment with techniques that have been fully developed and are in general use at the present time. A schematic drawing of a horizontal barrier in a reservoir is shown in Fig. 1. Two maximum stable water cones are illustrated-—-one for the wellbore diameter and the other for a barrier. A maximum stable cone is one that has attained its maximum volume at the critical production rate and is on the threshold of producing water. The volume displaced by each water cone and the rise in water table are indications of the amount of water-free oil produced. Corrections for porosity, connate water and residual oil, of course, must be applied. The water-oil interface which defines a maximum stable cone is called a free surface. It is a surface over which the pressure is constant. This free surface has the shape of a limiting streamline at and below which there is no movement or transport. The shape of the water cone describes the pressure drop in the reservoir. The effect of a completely impermeable barrier on the cone shape is essentially the same as extending the wellbore out to the barrier radius. The placement of a horizontal barrier requires that a horizontal fracture be created using a single-point entry technique. Two methods may be employed for filling this fracture. One method consists of propping the fracture before filling with cement. The other consists of fracturing with fracture fluid, then immediately following with cement

By Ursula E. Wolff

Il.lechanica1 twins have been observed in brigsten single crystals of a variety of axial orientations defornzed at room temperature in tension or bending. The twins formed near the final fracture and were up to 3 p thick. The twinning plane was always of the type (113). Twinning at room ternperature occurred only after considerable prior slip. Twins usually preceded fracture and nucleated cracks. The crack surfaces often alternated between a (001) plane and the twin interfaces. Secondary twins could also nucleate from cracks. In the absence of twinning tensile samples failed by shear; twinned samples failed by cleavage. On the assumption that observed sudden load drops in the stress-strain curves are associated with twinning, a critical resolved stress for twinning of 60, 000 to 65, 000 psi was calculated. MeCHANICAL twinning has been observed in iron and iron alloys at low temperature by a number of investigators.'-7 Similarly, for high-purity tungsten, twinning has been reported for deformation temperatures below 211°K.8-10 In W-Re and Mo-Re alloys, 20 pct Re was determined as the lower limit for twin formation at room temperature." Since the twins are generally very narrow, they are usually identified only by etching techniques. The expected (112) habit plane has always been confirmed by angular analysis of the surface traces. Recently, however, a complete identification by X-ray analysis has been performed on twins in a Mo-35 pct Re alloy.12 During an investigation of the deformation charac- teristics of tungsten single crystals, twins were revealed in tensile and bend samples deformed at room temperature. This paper deals with the conditions for such twinning and the relation of twinning to fracture. EXPERIMENTAL PROCEDURE Tungsten single crystals, 1/8 in. in diam, of a variety of axial orientations were grown from un-doped material by four-pass electron-beam zone melting. A representative analysis is given in the following table: From these crqstals, tensile samples with 1 in. gage lengths were made by surface grinding, leaving shoulders for gripping. The diameter after grinding was 0.082 in. The distorted surface layer was then removed by ele1:trolytic polishing which reduced the diameter of the gage length to 0.080 in. Tensile tests were carried out at room temperature in an Instron machine under two different sets of conditions: a) Rigid mounting; strain rate 0.02 in. per in. per min. b) Gimbal mounting; strain rate 0.002 in. per in. per min up to a total strain of approximately 0.2 pct, then 0.01 in. per in. per min to fracture. Stress axis and growth direction coincided in all samples and are subsequently called orientation.

Jan 1, 1962

By A. A. Burr, D. G. Ebeling

The effects of casting texture, grain orientation and grain size upon the performance of Alnico permanent magnets is described. Single-crystal specimens were produced by special sintering and grain coarsening techniques to study the effect of crystal orientation. In addition to texture and orientation effects, an analysis of the results indicates that the permanent magnet performance is impaired by a refinement of the grain size. AN excellent historical review of the development of Alnico permanent magnets has been prepared by Bozorth.1 The desirable permanent magnet characteristics of Fe-Ni-A1 alloys were discovered in 1932 by Mishima.2,3 The work of Ruder' showed that the alloys were age-hardenable, and Betteridge5 defined the best composition and heat treatment for the magnetically isotropic alloy known as "Alnico 3." Horsburgh and Tetley0 increased the energy product by the addition of cobalt and copper, "Alnico 2," and Oliver and Sheddon7 demonstrated that cooling in a magnetic field improved the residual induction of this alloy. Jonas8,9 then disclosed the great practical benefits of heat treating an alloy of higher cobalt content in a magnetic field and the resulting alloy, "Alnico 5," has become the standard of the industry. This paper describes the fundamental aspects of a procedure which can be used to further improve the properties of these anisotropic permanent magnet alloys. A study of the casting techniques used in the production of anisotropic Alnico permanent magnets indicated that the magnetic quality was affected by the as-cast macrostructure. Improved performance was observed in magnets containing a high percentage of columnar grains whose long axes were parallel to the magnetic axis of the casting. McCaig10 studied the effect of such columnar grain structures upon the magnetostriction characteristics of similar alloys, however no data was presented showing the effects on other magnetic properties. The following paragraphs describe two experiments which were conducted to determine the effect of various grain orientations upon the energy product. Special composite molds were prepared of highly conductive and highly refractive components to remove the heat of solidification from the casting in a controlled manner. Representative macrostructures produced by these techniques are shown in Fig. 1, along with the relative volumes of favorably oriented columnar grains. The alloy, Alnico 5, has the highest permanent magnet performance of any commercial magnet material. It has the nominal weight composition of 8 pct Al, 14 pct Ni, 24 pct Co, 3 pct Cu, and 51 pct Fe. A heat of this material was cast into molds producing the type A and B grain structures shown in Fig. 1 and pairs of the resulting magnets were placed in heat-treating boats so as to eliminate any biasing effects of boat position. After a standard heat treatment the type A magnets, with 16 pct of the volume composed of favorably aligned grains, had a maximum energy value of 3,940,000 gauss-oersteds, while the type B magnets with 73 pct aligned grains averaged 5,090,000. This large im-

Jan 1, 1954

By Robert N. McIndoo

A good tire program must begin at the top; management must have an awareness of the tremendous potential for cost saving that tires represent. At Reserve Mining Co., tires account for 33% of the cost of maintaining its 44 tractor-trailer side-dump haulers and 22% of its 32 rear-dump trucks. In comparison, engine overhauls account for only 6% of the maintenance dollar. Doubling the present engine life would save only 3%. The open-pit mine, located near Babbitt, Minn., moves about 46 million t/y with its off highway fleet. Mine roadways total in excess of 160 km (100 miles) and about 1200 tires are in active use at any given time.

Jan 3, 1978

By J. L. Christie, R. H. Leach

SO much has been written recently about the use of silver to replace scarce metals that certain facts about silver and its uses should be of interest. Figures for the production and use of silver, taken from the Handy & Harman annual reviews of the silver market, are given in Table 1. It will be seen that the rate of production has remained fairly constant and has been affected in recent years by the production of base metals, of which silver is a by-product. In each of the years 1937, 1938, and 1939, the U.S. Government acquisitions alone exceeded the entire world production, the difference, of course, being made up by imports of previously accumulated stocks. In 1940 and 1941 the U. S. Government acquisitions plus the United States and Canadian uses in the arts and industries exceeded the Western Hemisphere production. The U.S. Government pays a premium price for silver newly mined in the United States, at present 71.11c. compared with the price of 35'/8c. for foreign silver, with the result that the current U. S. production is not used commercially for the arts and industries. At the time this is written (June 1942) there is much uncertainty as to the future effect of this situation.

Jan 1, 1942

By Barry K. McMahon

Following minor slope failures at the commencement of mining the west wall of the Kanmantoo Mine was redesigned from an overall slope between haul roads of 55° to 46°. This decision was based on a probabilistic analysis which indicated that 46° was the optimum economic slope.

Jan 1, 1983

By C. S. Giggins, F. S. Pettit

The oxidation properties of Ni-Cr alloys with fine grains, coarse grains, and deformed surface layers have been studied at temperatures of 900" and 1100°C in 0.1 atm of oxygen. The oxidation rates of alloys containing between 10 and 30 wt pct Cr have been found to be dependent upon the grain size of the alloy. Finegrained alloys had smaller oxidation rates than coarsegvained alloys because of the selective oxidation of chromium at alloy grain boundaries. In this compositional range alloys with deformed surface layers behaved similar to fine-grained alloys due to recrys-tallization of the deformed surface layer. In the preceding paper1 it was found that during the oxidation of Ni-Cr alloys, the volume fraction of precipitated Cr2O3 could be greater at alloy grain boundaries than at other areas of the alloy surface. In the case of alloys with chromium concentrations equal to or greater than 30 pct,* the volume fraction of Cr2O3 *AIL compositions are given as weight percent unless specified otherwise. precipitated at grain boundaries and within grains on the alloy surface both exceeded the critical amount required for lateral growth of the Cr2O3 particles and the surfaces of these alloys were completely covered with a continuous, external layer of Cr203 during oxidation. However, in the case of alloys with chromium concentrations between approximately 5 to 30 pct, the volume fraction of precipitated Cr2O3 exceeded the critical value required for external scale formation only at grain boundaries.but not within the interior of the grains. Consequently, the surfaces of these alloys had external scales of Cr3O3 over the grain boundaries but internal Cr2O3 subscales with external scales of NiO away from the grain boundaries. Under these latter conditions, it was found that chromium could diffuse laterally in the alloy from those areas covered with an external layer of Cr2O3, i.e., grain boundaries, to areas where the Cr2O3 was present as a subscale. This diffusion of chromium resulted in an increase in the volume fraction of Cr2O3 precipitated in the sub-scale zone and continuous layers of Cr2O3 could be formed at the subscale front in these regions. For the alloys used in the previous studies,' continuous layers of Cr2O3 were formed on Ni-20Cr alloys in the subscale regions after approximately 30 hr of oxidation at 900°C. For shorter periods of oxidation, the Cr2O3 layer was semicontinuous with the continuous portion at the subscale front emanating from points where the Cr2O3 had been formed as an external scale over alloy grain boundaries. Some lateral growth of a Cr2O3 layer in the subscale region was observed on Ni-15Cr and even Ni-10Cr alloys but this layer was never continuous after 30 hr of oxidation. These results indicate that the selective oxidation of chromium in Ni-Cr alloys with chromium contents between 5 to 30 pct may be dependent upon the grain size of the alloy. Fine-grained specimens in this compositional range should have a larger fraction of the surface covered with external Cr2O3 than coarsegrained specimens and the subscale areas required to be sealed via lateral diffusion of chromium should be smaller. It is therefore to be expected that a continuous layer of Cr2O3 can be formed on alloys in this compositional range after short periods of oxidation providing the alloy grain-size is sufficiently small. bo studieS2,3 have established that the oxidation behavior of alloys can be significantly influenced by pretreatments which produce mechanically deformed surfaces. It has been found that deformed surfaces usually promote the selective oxidation of elements in alloys and it is believed that these effects are due to rapid diffusion of elements in the deformed layer. In view of the previous results,' which showed that alloy grain boundaries may play an important role in the selective oxidation of chromium in Ni-Cr alloys, deformed surfaces may promote the selective oxidation of elements in alloys as a result of the numerous grain boundaries formed on the alloy surfaces via recrys-tallization during heating to the oxidation temperature. The purpose of the present studies was to determine the effect of alloy grain size and surface deformation on the selective oxidation of chromium in Ni-Cr alloys at temperatures of 900" and 1100°C in 0.1 atm of oxygen. EXPERIMENTAL The average grain diameter of the alloys used in the previous studies1 was not less than 0.04 mm and alloys with compositions between 5 and 30 pct chromium had average grain diameters between 0.04 and 0.14 mm. Since the oxidation kinetics were already available for these relatively coarse-grained alloys, it was desirable to use these same alloys in the present studies. The surfaces of the alloys listed in Table I of the previous paper were deformed by using a Model F S.S. White Industrial Airbrasive Unit, which delivered a controlled mixture of 25 µ Al2O3 particles in a stream of dry air at high velocity against the surface of a specimen. The amount of surface deformation produced by this treatment was not determined but a re-crystallized layer about 15 µ thick was formed upon annealing deformed specimens. The grain size at the surface of the specimens was reduced to an average grain diameter of 0.01 mm by annealing the deformed specimens, i.e., grit-blasted,

Jan 1, 1970

By N. Arbiter, J. Steininger, C. C. Harris

Power consumption and operating variables in air-liquid systems for a wide range of operating conditions in the turbulent region have been correlated by two dimensionless groups involving the power ratio and the flow number. The form of the correlation was developed by considering flow balances related to the air-liquid composite density in the impeller zone. Data for two phase air-liquid systems, both from literature and from the present investigation, has been correlated with high statistical significance. Two phase solid-liquid and three phase gas-liquid-solid systems have also been correlated. The quantification of power requirements in the agitation of liquids is well established.1 Rushton, Costich and Everett have shown that, for mixers operating in the fully turbulent region with no vortex, the power number

Jan 1, 1964

By J. R. Thompson

It is common practice, and certainly good business as all of us know, to take care of plant operating equipment. Machinery of any type requires periodic inspection and planned maintenance. With this thought in mind a plant operator should at the end of every shutdown period make regular belt inspections and plan for later appropriate care and maintenance. The points mentioned below are understood well by all of us but are sometimes forgotten because belt conveyors are comparatively easy to operate. Maintenance of any conveyor belt is dependent upon the fundamental characteristics of the two component parts-cover and carcass.

Jan 6, 1950

By J. J. Frawley, W. J. Childs, W. R. Maurer

The object of this investigation was to determine the growth habit of bismuth and bisrrtuth alloy dendrites as a function of supercooling. To do this, techniques were developed to increase the amount of supercooling in bismuth and bismuth alloys. For pure bismuth, the growth habit was dependent on the amount of supercooling. At low amounts of supercooling, about 10" C, prismatic dendrites were obtained. With increased supercooling, about 20 C, a hopper growth habit was observed. In many cases where hopper growth had occurred, the hopper dendrites were twinned during the growth process. This twinned surface enable prismatic dendrites to nucleate and grow by a twin plane mechanism. When the amount of supercooling was increased to about 25 °C, the growth habit was a triplanar growth. With still greater supercooling, about 3s°C, a branched growth habit occurred. The exposed planes on the prismatic, hopper,, triplane, and branched dendrites have been determined. The growth habit of the dendrites which grew along the crucible wall was found to have the (111) as the exposed plane, with <211> growth direction. It is apparent that dendritic growth of a metal is dependent on its purity and the solidification variables present. One of the solidification variables is the degree of supercooling. Supercooling, although often observed, has not been studied extensively until recent years. For dendritic growth to occur in a pure metal, the metal must be thermally supercooled. After the dendrites grow into the supercooled melt, the heat of solidification raises the temperature of the specimen to the melting point of the material and the remaining liquid will solidify at this temperature. Decanting is the removal of this remaining liquid before complete solidification. This removal of the remaining liquid after recalescence had occurred is a great aid in the study of dendritic growth. In this investigation, decanting was accomplished by a vacuum-decanting technique . Other investigators1-5 have studied the growth characteristics of various low-melting-temperature pure metals and alloys as a function of supercooling. However, large degrees of supercooling were not included. For their study of dendritic growth of lead, Weinberg and chalmersl employed a decanting technique which was achieved by pouring off the remaining liquid, exposing the solid/liquid interface. This method was employed later by Weinberg and Chalmers2 for the investigation of tin and zinc dendrites. The method for obtaining a solid/liquid interface was improved by Chalmers and Elbaum. They employed a triggered spring which was attached to the solidifying section of the specimen. Upon activation, the spring jerked the solid interface away from the liquid melt. In the study of growth from the supercooled state, a metal of low melting point which exhibited a high degree of supercooling was desired. Bismuth gave very consistent supercooling when a stannous chloride flux was employed. The maximum supercooling obtained was 91°C, with an average supercooling of between 65" and 75°C. The consistency of supercooling greater than 50°C was very high. The use of vacuum to aid in the rapid decanting of molten metal has proven to be very successful in this investigation. The vacuum gives a rapid decantation, usually leaving the solidified metal structure sharply defined. The purpose of this investigation was to study the effects of supercooling and the effects of alloy additions on the growth habit of bismuth dendrites. The structure of bismuth has been variously defined as face-centered rhombohedral, primitive rhombohedral, and hexagonal. However, bismuth has only one plane with threefold symmetry, the (111) plane, and the crystal-lographic structure is considered a 3kn structure. MATERIALS The bismuth which was employed in this investigation was obtained from the American Smelting and Refining Co. of South Plainfield, N. J. The accompanying spectrographic analysis data indicated the bismuth to be 99.999+ pct pure. The tin was obtained from the Vulcan Materials Co., Vulcan Detinning Division, Sewaren, N. J. It was classified as "extra pure". Nominal analysis was 99.999+pct. In order to prevent contamination of the bismuth melt from the atmosphere, an anhydrous stannous chloride (Fisher certified reagent grade) was added to each melt. The fluxing action obtained from the use of the chloride provided a large amount of supercooling in the specimen. APPARATUS A 30-kw, 10,000-cps motor-generator set, connected to a 6+-in.-diam air induction coil, was employed to melt and superheat the specimens. The temperatures were recorded by means of a chromel-alumel thermocouple and a potentiometric recorder. The thermocouples were 0.003 in. in diam, and were encapsulated with Pyrex glass to prevent the thermocouple from acting as a nucleating agent and also from contaminating the melt. Fig. 1 illustrates the vacuum-decanting apparatus when a liquid flux was employed. A standard 30-ml Pyrex beaker was placed on top of an asbestos insulating block. A 5-mm-ID Pyrex tube with aA-in. spacer tip attached to its end was used for the decanting tube. The spacer tip contributed significantly to a successful decanting operation. The tip located the opening of the decanting tube about -^ in. from the bottom of the

Jan 1, 1969

By W. T. Turrall, D. Porter

The paper describes a machine developed for the purpose of concentrating clear optical grade fluorspar crystal from a feed material containing less than 1 pct impurities. The principle of concentration is based on the fact that in a liquid having an index of refraction equal to that of fluorite (n — 1.434) clear crystals are invisible, whereas crystals containing occluded impurities absorb a part of the light. As the crystals pass through a light beam, undesired crystals give themselves away by creating a shadow on a photoelectric receiver. .The shadow is converted by the photoelectric cell into an electric pulse. An electronic circuit amplifies this pulse and commands the operation of a mechanical concentrator. Hp HE crystal laboratory, Dept. of Physics, Massa--*- chusetts lnstitute of Technology, was confronted with the problem of obtaining a supply of optical grade calcium fluoride (CaF,) for use in growing synthetic CaF, crystals. A search of the known fluorspar deposits did not indicate that any quantity of optical spar could be obtained. Even the best material had to be sorted by hand to remove impurities. The process for growing CaF, crystals developed by Professor D. C. Stockbarger of the Dept. of Physics, M.I.T., necessitates very pure feed materials. Exclusion of impurities is required, even in amounts detectable only spectrographically. The impurities occurred as minute inclusions of SiO,, BaSO,, CaCO,, FeS2, water or air. Crystals up to 4 in. in diam and weighing several pounds are made by the Harshaw Chemical Co. in Cleveland. Since the time required to grow a 4-in. crystal is about one week, and since the cost of manufacture is high, removal of impurities by any concentration method appeared practical. The mineral engineering section of the Dept. of Metallurgy undertook to investigate the possibility of concentrating clear optical fluorspar, —4 mesh + 10 mesh, from a feed containing over 99 pct CaF,. Various innovations of the known methods of concentration were considered, but in each case the minute amount of impurities associated with the crystal produced such extremely small differences

Jan 1, 1953

By W. T. Turrall, D. Porter

The paper describes a machine developed for the purpose of concentrating clear optical grade fluorspar crystal from a feed material containing less than 1 pct impurities. The principle of concentration is based on the fact that in a liquid having an index of refraction equal to that of fluorite (n — 1.434) clear crystals are invisible, whereas crystals containing occluded impurities absorb a part of the light. As the crystals pass through a light beam, undesired crystals give themselves away by creating a shadow on a photoelectric receiver. .The shadow is converted by the photoelectric cell into an electric pulse. An electronic circuit amplifies this pulse and commands the operation of a mechanical concentrator. Hp HE crystal laboratory, Dept. of Physics, Massa--*- chusetts lnstitute of Technology, was confronted with the problem of obtaining a supply of optical grade calcium fluoride (CaF,) for use in growing synthetic CaF, crystals. A search of the known fluorspar deposits did not indicate that any quantity of optical spar could be obtained. Even the best material had to be sorted by hand to remove impurities. The process for growing CaF, crystals developed by Professor D. C. Stockbarger of the Dept. of Physics, M.I.T., necessitates very pure feed materials. Exclusion of impurities is required, even in amounts detectable only spectrographically. The impurities occurred as minute inclusions of SiO,, BaSO,, CaCO,, FeS2, water or air. Crystals up to 4 in. in diam and weighing several pounds are made by the Harshaw Chemical Co. in Cleveland. Since the time required to grow a 4-in. crystal is about one week, and since the cost of manufacture is high, removal of impurities by any concentration method appeared practical. The mineral engineering section of the Dept. of Metallurgy undertook to investigate the possibility of concentrating clear optical fluorspar, —4 mesh + 10 mesh, from a feed containing over 99 pct CaF,. Various innovations of the known methods of concentration were considered, but in each case the minute amount of impurities associated with the crystal produced such extremely small differences

Jan 1, 1953

By R. J. Marcotte, C. T. Eddy, R. J. Smith

The objectives of the investigation herein reported were to determine: (I) the S-curves for certain selected cast steels, (2) whether or not the published S-curves for wrought steels are satisfactory for use on cast steels of similar composition, and (3) to prepare hardenability curves of the selected cast steels. In order to make the final comparisons between cast and wrought steel more completely tangible, it was deemed advisable not only to determine S-curves for the steels submitted in the cast condition but also to roll some of the cast-steel test bars and determine comparison S-curves on such wrought material. This procedure eliminates the composition variable and makes it possible to reveal the differences resulting from plastic deformation of the cast structure in addition to providing the comparison with published data on wrought steels. Cast Steels The cast steels selected for the preparation of S-curves, or time-temperature transformation curves, were similar to S.A.E. series 1030, 2330, 4130 and 4330. Of these the 1030 was supplied by The Crucible Steel Casting Co., Cleveland, Ohio, and the other three by The Sawbrook Steel Castings Co., Lockland, Ohio. The steels were furnished in the as-cast condition. The manufacturers supplied the chemical analyses and the properties that could be obtained in the heat-treated condition—all of which is summarized in Table I. The metallographic and dilatometric procedures and equipment were in general standard. The specific technique employed was described in a report of the Steel

Jan 1, 1945

By B. H. Dunshee

THIS paper is not intended to be a technical discussion of square-set framing as used in mines, but merely a short description of the different kinds of framing that have been used in the Butte mines, and what has been decided upon, after years of practical experience, as being the best, taking into consideration the physical condition of the veins and country rock, and. also the supply of timber available for mining purposes. Butte is, essentially, a square-set district. Virginia City, Nev., was the first mining camp to use this method of timbering, and to Philip Deidesheimer, who went to the Ophir mine in 1860, is given the credit of solving the problem of square-set framing, where large bodies of ore were stoped and the timbers were supposed to hold the ground from caving without any filling. That he did his work well is shown by the fact that the main features of his framing are in use to-day. In the Butte mines the conditions are such that this method of timbering is generally used. We do not, of course, depend upon the timbers any more than is necessary. The worked-out stopes are filled with waste rock as close behind the miners as possible and not interfere with mining operations. The waste rock is obtained from development work on the different levels or from the surface. In the earlier days of mining in Butte there were numerous independent companies and naturally there were different ideas as to the best way to frame the square sets, although the general features were the same.

Jan 8, 1913

By Alfred H. Bell, George V. Cohee

In 1939 Illinois produced 94,302,000 bbl. of oil—almost three times the amount of oil produced at the peak in 1908, when development in the southeastern Illinois field was at its height (Fig. I). It represents nearly a fourfold increase over the 24,075,000 bbl. produced in 1938 (Table 6). This rapid increase in oil production in Illinois is largely due to development in the Salem and Louden fields (Table I). During 1939 daily production for the state increased from 135,000 to 332,572 bbl. A notable increase in production for 1940 is expected as a result of the drilling of the Devonian limestone in the Salem and Centralia fields,

Jan 1, 1940

By Alfred H. Bell, George V. Cohee

In 1939 Illinois produced 94,302,000 bbl. of oil—almost three times the amount of oil produced at the peak in 1908, when development in the southeastern Illinois field was at its height (Fig. I). It represents nearly a fourfold increase over the 24,075,000 bbl. produced in 1938 (Table 6). This rapid increase in oil production in Illinois is largely due to development in the Salem and Louden fields (Table I). During 1939 daily production for the state increased from 135,000 to 332,572 bbl. A notable increase in production for 1940 is expected as a result of the drilling of the Devonian limestone in the Salem and Centralia fields,

Jan 1, 1940

By H. Kenworthy, R. B. Fisher, R. G. Knicherbocker, M. M. Fine

The progress made to date in the mineral dressing of complex Arkansas titanium ores is reported in this paper. Concentrates of rutile, a dioxide of titanium, were produced by treating a submarginal ore from the Magnet Cove Rutile Co., Inc., Magnet, Ark. The rutile recovery at present is 45 to 50 pct of the total TiO2, with the possibility of increased recovery with additional research. The work reported herein is part of a general study which will later include results of investigation of other titanium ore bodies in the Magnet, Ark., area. The fragile character of the rutile minerals, the softness of the gangue, the occurrence of pyrite and leucoxene, and the considerable proportion of extremely small size rutile in the presence of montmorillonite- and illite-type clays in the Magnet Cove open-pit mine are the important factors in the mineral dressing of this submarginal rutile ore. History The occurrence of titanium minerals in the Magnet Cove area of Arkansas was recognized as early as 1890, but it was not until about 1912 that any appreciable prospecting for the minerals was undertaken. At that time drilling was begun, a shaft was sunk, and several drifts were driven, but beneficiation to recover the titanium minerals was not attempted. The only successful mining and milling operation of the Magnet Cove rutile deposit was begun in 1932 by the Titanium Corp. of America and continued until 1942. The ore was washed by means of a rotary scrubber and then deslimed in a drag classifier. The discharge was ground in a rod mill, classified, and tabled to recover a rougher rutile concentrate, which was screen-sized and retabled on cleaner tables. The cleaner concentrates were given a reducing roast, screen-sized, and magnetically separated to produce a finished rutile concentrate. Most of the rutile produced during this period was sold abroad. In 1942, the Titanium Alloy Corp. of Arkansas (a subsidiary of the Titanium Alloy Manufacturing Co. of New York) purchased the property and rebuilt the mill. Subsequently, the plant and property were acquired by the Magnet Cove Rutile Co., Inc., of Little Rock, Ark., the present owners. Very little titanium has been produced since 1942. Although the Titanium Corp. activities yielded enough returns to allow continued operation for approximately 10 years, certain factors must be recognized. These are: (1) production of rutile in that period was during a low in the economic cycle which permitted low-cost operation on a small scale, and (2) a considerable portion of the production was above the water level and no drainage problems existed. Prior to this paper there has been no published report of any mineral-dressing investigation of the lower levels of the ore body. Reference is made in another paper1 to an earlier investigation of Magnet Cove rutile by the Rolla laboratory, in which it is stated that recoveries of 12 to 17 pct of the rutile were obtained. The present investigation was undertaken to improve the known milling processes and to provide adequate metallurgical information about the ore treatment. Titanium Technology The titanium mineral of primary interest in the present investigation was the titanium dioxide, rutile. Rutile is one of the industrial minerals whose annual consumption is relatively small but strategically important. The domestic production of rutile was 7100 tons in 1948. The imports of rutile in the same year were approximately 8000 tons.2 A major use of rutile is in the production of welding-rod coatings, for which a product containing a minimum of 92 pct titanic oxide is desired. Other constituents, such as lime, silica, and sulphur, must be held to a minimum, but hard-and-fast specifications for these elements cannot be drawn. It is necessary to incorporate the rutile in a welding-rod coating, make a sufficient number of test welds, and then determine the tensile strength of the weld metal in the as-welded and stress-relieved conditions. Such a test gives

Jan 1, 1950