Search Documents

By J. M. Donkers, R. de Groot

The various objectives of dredging at sea require different methods and radically different equipment for their optimum fulfillment. In the majority of cases, sea dredging is done by means of dredging equipment connected to a pontoon or ship floating at the surface. As the supporting hull is subject to the influence of waves, swells, currents and wind, the connecting point of the dredging equipment to the hull will generally move relative to the sea bottom with 6° of freedom. The more important hull motions are surge, heave, pitch and roll. Depending on the actual sea and weather conditions and the size of the hull, some of these motions can be so large that dredging equipment of rigid construction (normal or inland dredges) cannot be used. In those cases where mechanical disintegration of the bottom is necessary and where accurate dredging is required, the designer must find a solution for this problem. For cases where the bottom consists of soils that can be handled by plain suction, highly sophisticated dredging equipment such as the trailing suction hopper dredge permit dredging under all but the most severe sea state conditions. This type of dredge picks up the soil from the sea bottom while slowly underway. The drag suction head is fitted on a suction pipe of such flexibility that the supporting ship can carry out all six movements in relation to the draghead (heave, pitch, roll, sway, yaw and surge), while the draghead remains in firm contact with the bottom. The suction pipe is fitted with flexible hoses, a universal hinge, a horizontal hinge, axial turning gland and sliding turning gland with horizontal axis and is suspended flexibly from the ship incorporating swell compensating buffer gear, keeping the wires taut and the draghead bottom contact pressure fairly constant while the dredge moves up and down. Due to the fact that the draghead has a low bottom contact pressure and has little tendency to sink into the bottom, this compensation is not difficult to realize.

Jan 4, 1974

By Ralph A. Sherman, John Blizard

The experimental investigation described in this paper was conducted to determine the relative combustibilities of different samples of blastfurnace coke when burned in a current of air in a small furnace. It was undertaken in connection with the work done by Perrottl and Kinney2 on the process of combustion in the blast-furnace hearth.3 Reference is often made to the "combustibility" of coke by blastfurnace men, but exactly what is meant by the term "combustibility" is somewhat vague. Brassert,4 in a paper before a meeting of blastfurnace men in 1914, refers to combustibility as follows: The value of the coke in relation to the heat reactions in the furnace is determined not only by the carbon content but even more so by its combustibility. This, in turn, is governed by its size, the physical and chemical composition of the carbonaceous substance forming the cell walls, and the interior and surface structure of the coke pieces. These properties are, in turn, influenced by the chemical and physical properties of the coals used for coking, the density of the cake of coal in the oven, the coking time, temperature and heat regulation of the ovens, and last, but not least, by the method of quenching, screening and handling the finished coke. What principally concerns the blast furnace is the rate of progression of the combustion, which depends not so much on the chemical analysis as on the physical qualities of the coke. It is this rate of progression that we term combustibility, which is the speed at which the carbon molecules in the coke combine with oxygen under given conditions. In general, what the blast furnace requires is a coke which will burn rapidly and with intensity at the tuyeres, yet which has a sufficiently strong structure and hard surface to resist abrasion and solution by CO2 in the upper part of the stack.

Jan 1, 1923

By John Blizard, Ralph A. Sherman

The experimental investigation described in this paper was conducted to determine the relative combustibilities of different samples of blastfurnace coke when burned in a current of air in a small furnace. It was undertaken in connection with the work done by Perrottl and Kinney2 on the process of combustion in the blast-furnace hearth.3 Reference is often made to the "combustibility" of coke by blastfurnace men, but exactly what is meant by the term "combustibility" is somewhat vague. Brassert,4 in a paper before a meeting of blastfurnace men in 1914, refers to combustibility as follows: The value of the coke in relation to the heat reactions in the furnace is determined not only by the carbon content but even more so by its combustibility. This, in turn, is governed by its size, the physical and chemical composition of the carbonaceous substance forming the cell walls, and the interior and surface structure of the coke pieces. These properties are, in turn, influenced by the chemical and physical properties of the coals used for coking, the density of the cake of coal in the oven, the coking time, temperature and heat regulation of the ovens, and last, but not least, by the method of quenching, screening and handling the finished coke. What principally concerns the blast furnace is the rate of progression of the combustion, which depends not so much on the chemical analysis as on the physical qualities of the coke. It is this rate of progression that we term combustibility, which is the speed at which the carbon molecules in the coke combine with oxygen under given conditions. In general, what the blast furnace requires is a coke which will burn rapidly and with intensity at the tuyeres, yet which has a sufficiently strong structure and hard surface to resist abrasion and solution by CO2 in the upper part of the stack.

Jan 1, 1923

By Oswald J. Heinrich

IN this paper I shall attempt a description of the successful extraction of coal from this property after it had been on fire for probably fifty years, or more, and after attempts, made at various times, which had still left considerable coal behind. The Richmond coal-field has a well-founded bad reputation, arising from the circumstance that many of its collieries have had to be abandoned, from time to time, if not entirely, on account of fires, caused by spontaneous combustion, to which the character of the coal in this field renders them peculiarly liable. While I fully assent to the opinion that this trouble lies in the nature of the coal, which is highly bituminous, and the seams of which are, moreover, divided by slaty bands, through which, as also in the coal, iron pyrites is more or less disseminated, often in microscopically small particles, I must, nevertheless, declare that many lamentable disasters, causing great loss of life and property, could have been avoided if a suitable system of mining had been pursued in all the collieries. If this could not have been done from the beginning of mining in this section of country (the history of which can be traced back to over one hundred years), at least experience enough existed upon this subject thirty and forty years ago to dictate the avoidance of the dangers to a considerable extent. It is therefore necessary here to refer first, in a few remarks, to the character of the coal deposits, particularly in this immediate neighborhood, the Midlothian being one of the oldest and most extensive mines, and some of its coal being much subjected to spontaneous combustion. I must also refer to the history of former managements to explain more clearly the results which were arrived at. The Midlothian coal-mine property, situated upon the eastern outcrop of the basin, about four miles south from James River, exhibits

Jan 1, 1873

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

MELTING in a crucible is the customary method for small things. It is done in two ways: with the blast of bellows and with an air furnace. The one with bellows, which I wish to show you now, is the common method most in use. It melts quickly and is very well known to goldsmiths and to all melters. I could continue without telling you of it, but I shall tell you its method in order to caution you about what you might perhaps not notice. In order to do this, first make a little forge with a pair of bellows that can be worked with one hand or in some other way. A crucible of the size needed is then taken and filled with the material that you wish to melt. Then, on the forge in front of the place where the wind issues from the bellows, kindle as much charcoal as you think will well cover your crucible and put your crucible full of material in the midst of this burning charcoal above the place where the blast strikes the fire, two or three dita distant from the place where the blast issues-or as much more or less as the size of the crucible or the force of the bellows requires. It is allowed

Jan 1, 1942

By E. M. Boatman, S. J. Pirson, R. L. Nettle

More than a decade ago some theoretically derived relationships were proposed that permitted the prediction of the relative ability of reservoir fluids (oil, gas, water) to flow simultaneously within the porous structure of rocks. While many successful predictions of fluid-flow ratios from wells have been made from electric logs, the theoretical deductions have not been subjected to laboratory verifications. For the relative permeability to liquid and gas, simultaneous flow of water and air was used, employing the familiar external-gas-drive technique. While in the process or water desaturation, the resistivities of the test cores (Woodbine sand) were measured. Their permeabilities varied from 10 to 280 md. The laboratory results indicated the need for changing the values of exponents in the theoretically derived formulas, whereas the form of the functions of resistivities and saturations remained as derived by theory. For the relative permeability to oil and water, the three-core dynamic technique was used on six cores. In this case it was found that the formulas were valid with but slight modification as derived by theory, to a sufficient degree of accuracy for engineering use and for well productivity prediction from electric logs. INTRODUCTION Conventional quantitative well log interpretation generally stops after reasonable values for formation porosities and water saturations have been established. Yet such in formation is insufficient to predict either the outcome or the desirability of well tests and completion, let alone the economic aspect of producing oil- and gas-bearing sections which might have been established by conventional log analysis. To give an engineering answer to such questions, it is necessary to predict the expected fluid flow ratios, the productivity index and the ultimate recovery from potentially productive wells. This problem requires in part for its solution a determination of the relative permeability characteristics of the potentially producing formations, both to oil (or water) and gas, and to oil and water.

Jan 1, 1965

By G. V. Woody, J. D. Price

Many producers of by-product coke have spent considerable time and given considerable thought to the use of a substitute for low-volatile coal as an admixture with high-volatile coking coal for charging high-temperature by-product coke ovens. Generally speaking, there are two principal reasons for this, one being occasioned by the lack, in certain localities, of low-volatile coal delivered at a cost sufficiently low to permit its use, and another being the desirability of finding a substitute product with a delivered cost lower than the cost of the low-volatile coal. It was for the first of these reasons that the Colorado Fuel and Iron Corporation was particularly interested in this subject. This paper deals with the experimental work and the results obtained by that company in producing and using low-temperature char. Overcoming Defects in Coke from Colorado Coals Colorado coking coals are all of the high-volatile type and were all laid down during the Cretaceous period, which makes them something like 80 million or so years younger, geologically, than eastern coals. They behave, when coked alone, something like the Pittsburgh-seam coals. They make a very brittle, highly cross-fractured, fingery coke of fair shatter value but quite low in resistance to abrasion. Mixed with a low-volatile coking coal such as Poca- hontas or certain Oklahoma coals, they make a coke that is equal to virtually any of the eastern cokes. The inferior quality of Colorado coke has long been recognized, and a considerable amount of time, effort and money has been spent upon investigations of means for improving its physical properties. While it has been found that some improvement in quality of coke can be secured by the adjustment and control of such variables as pulverization, moisture content, oven temperature and bulk density of charge, and through the addition of certain inert materials such as pulverized coke breeze, pitch, high-volatile noncoking or semicoking coal, the benefits so gained have been comparatively small. There are no low or medium-volatile coking coals available within a reasonable freight-cost distance. Therefore a substitute for low-vol-atile coal was developed through low-tem-perature carbonization—or, more correctly speaking, through the partial devolatiliza-tion—of high-volatile coals. The blending of this lower volatile char with the high-volatile coking coal distinctly improves the quality of coke made from Colorado coal. There is nothing especially new about this idea. In 1908 a Japanese patent was taken out by Kotaro Shimomura, whose claim was: The method of making a nonfingery coke out of bituminous coals, without using natural coals of low-volatile matter; according to which a certain coal is heated at a temperature between about 300°C. and about 600°C. so as to leave about 15 to 25 per cent volatile matter in the coal; this coal is mixed with the

Jan 1, 1944

By S. C. Sun, John A. L. Campbell

The surface properties exhibited by bituminous coal and bituminous coal lithotypes were ascertained by using streaming potential techniques. The electro kinetic prop-erties wereascertainederties of bituminous coal were found to be similar to those of anthracite. The principle electrokinetic properties of the coal and lithotypes, zero-points-of-charge (ZPC), and potential determining ions, were established. The effects of indifferent electrolytes, hydronium and hydroxyl ion sources, and polyvalent ions (cationic and anionic) were also evaluated. Location of the ZPC's with respect to pH is discussed in terms of chemical and mineralogical composition of the respective surfaces. To account for the observed electrokinetic phenomena, a generalized surface model and adsorption mechanism are proposed. Surface-dependent processes, such as froth flotation and flocculation, are important or potentially important techniques for combating some of the current major problems in coal preparation. In order to correctly apply or improve a surface-dependent process, it is of paramount importance to understand the interfacial phenomenon, especially the double layer properties, exhibited by the solid. The specific objective of this research was to determine the properties of the bituminous coal/liquid interface by an electrokinetic method, streaming potential, and to relate the findings, wherever possible, to the existing unit operations of froth flotation and floccula-tion tion. The electrokinetic properties of both the whole coal and its lithotypes were investigated. As part of the total investigation, the role played in the double layer by the reagents commonly employed in the surface dependent process was also established.' These data will be presented at a later date. Experimental Procedures The coal samples used in this research and their designations are listed in Table 1. The classical description of humic coal lithotypes as developed by Stopes" was used for the delineation of the lithotype samples. The samples were taken from the working face of a producing deep mine of the Pittsburgh seam in the area of Ellsworth, Pa. To avoid oxidation, only freshly exposed areas were sampled. The normal precautions against contamination were also exercised. Two types of samples were taken, specimens rich in a particular lithotype and a representative channel sample. The latter sample was prepared for analyses by grinding it to —35 mesh. It was screened repeatedly during the grinding to provide the largest amount of 35 x 48-mesh (standard Tyler sieves) material possible. The screened fraction was passed over a magnet and then washed several times with distilled water and finally with conductivity water. The resulting sample now termed "whole coal" was stored under conductivity water in a glass bottle. Pure lithotypes were obtained from the lithotype concentrates by hand picking, and were processed in the same manner as the representative sample. Maceral analyses, employing standard petrographic procedures," were performed on the lithotype samples to determine the purity of the samples. The results are presented in Table 2. Reflectance measurements of the vitrinites and fusinites are also reported in this table. Proximate and ultimate analyses of the samples are given in Tables 3 and 4. The electrokinetic properties of the coal samples were determined by streaming potential methods.'-' All of the chemicals used in the investigation were reagent grade (Baker analyzed). The conductivity water was prepared by doubly distilling the water in a pyrex Yoe-type still and passing the distillate through a mixed bed ion exchange column. Results In general, the electrokinetic properties of the investigated bituminous coal were found to be similar to the results of a previous study of anthracite by Camp-bell bell5 and are in accord with the suppositions of Brown." The zeta potentials of the coal and all the lithotypes were found to be negative in conductivity water. Jowett? in a study of slime coatings on coal also found bituminous coal to exhibit a negative surface. Fig. 1 shows that the negative charges, at neutral pH's, for both fusain and the gangue are very small, almost zero, while at the same pH, vitrain has the largest negative charge, almost 30 mv. Durain has a negative charge of 17.5 mv. The determination of the affect of pH on the charge of the coal surfaces revealed that hydronium and hydroxyl ions apparently behave as potential determining ions; however, they do not appear to be potential determining for the gangue. These results are illustrated in Fig. 1. As the pH of the solution was decreased, hydronium ions were adsorbed, causing the surface of the coal to reverse polarity and become

Jan 1, 1971

By J. D. Price, G. V. Woody

Many producers of by-product coke have spent considerable time and given considerable thought to the use of a substitute for low-volatile coal as an admixture with high-volatile coking coal for charging high-temperature by-product coke ovens. Generally speaking, there are two principal reasons for this, one being occasioned by the lack, in certain localities, of low-volatile coal delivered at a cost sufficiently low to permit its use, and another being the desirability of finding a substitute product with a delivered cost lower than the cost of the low-volatile coal. It was for the first of these reasons that the Colorado Fuel and Iron Corporation was particularly interested in this subject. This paper deals with the experimental work and the results obtained by that company in producing and using low-temperature char. Overcoming Defects in Coke from Colorado Coals Colorado coking coals are all of the high-volatile type and were all laid down during the Cretaceous period, which makes them something like 80 million or so years younger, geologically, than eastern coals. They behave, when coked alone, something like the Pittsburgh-seam coals. They make a very brittle, highly cross-fractured, fingery coke of fair shatter value but quite low in resistance to abrasion. Mixed with a low-volatile coking coal such as Poca- hontas or certain Oklahoma coals, they make a coke that is equal to virtually any of the eastern cokes. The inferior quality of Colorado coke has long been recognized, and a considerable amount of time, effort and money has been spent upon investigations of means for improving its physical properties. While it has been found that some improvement in quality of coke can be secured by the adjustment and control of such variables as pulverization, moisture content, oven temperature and bulk density of charge, and through the addition of certain inert materials such as pulverized coke breeze, pitch, high-volatile noncoking or semicoking coal, the benefits so gained have been comparatively small. There are no low or medium-volatile coking coals available within a reasonable freight-cost distance. Therefore a substitute for low-vol-atile coal was developed through low-tem-perature carbonization—or, more correctly speaking, through the partial devolatiliza-tion—of high-volatile coals. The blending of this lower volatile char with the high-volatile coking coal distinctly improves the quality of coke made from Colorado coal. There is nothing especially new about this idea. In 1908 a Japanese patent was taken out by Kotaro Shimomura, whose claim was: The method of making a nonfingery coke out of bituminous coals, without using natural coals of low-volatile matter; according to which a certain coal is heated at a temperature between about 300°C. and about 600°C. so as to leave about 15 to 25 per cent volatile matter in the coal; this coal is mixed with the

Jan 1, 1944

By Eizo Yabuuchi, Yukito Imanaga

INTRODUCTION In treatment of mine drainage, it is well known that the neutralization by calcium carbonate is far better than by slaked lime because of cheaper cost and better precipitability of its deposit. However, in case of iron ion contained in the mine drainage consists of ferrous salt, the ferrous salt must be oxidized to ferric salt before neutralization, because the ferrous salt does not react with calcium carbonate. At Yanahara Mine, during the period of 1950 through 1956, ferrous ion in the mine drainage had been oxidized to ferric ion, simultaneously neutralized by adding calcium carbonate into the aerated drainage. During the period of 1961 through 1974, after passing through many kinds of treating methods, the neutralization had been carried out by addition of calcium carbonate into the drainage after oxidized its ferrous ion to ferric by using nitrous gas as an oxidizing catalyzer. Meanwhile we had made an experiment on the oxidation of ferrous ion by utilizing iron bacteria, and developed a method which oxidized ferrous ion in large quantities briefly by cultivating and concentrating iron-oxidizing bacteria. Since 1974, we have been operating successfully for treating the drainage at Yanahara Mine by means of utilizing these bacteria.

Jan 1, 1976

By J. Leja, N. Sheikh

The stability of lead ethyl xanthate precipitate in aqueous environment of different pH (4.5 to 10.5) and at temperatures 25°C-60°C was investigated. Dissolution leads to a wide variation of pH, xanthate, and lead ions concentration in solution and to a deposition of solid products of reactions. X-ray diffraction patterns of these solids enabled identification of Pb(OH)3, PbCO3, and PbS as constituents of the remaining undecomposed Pb(EtX)1, together with some unidentified compounds (which give rise to intensive peaks with d values of 2.82A and 1.71A, and numerous peaks of lesser intensity).

Jan 1, 1974

Jan 11, 1950

By B. G. Ricketts, A. Kelly, P. A. Beck

The isothermal kinetics (at 200" to 400°C) of subgrain growth and of softening were studied in a 99.997 pct pure Al crystal rolled to 80 pct RA, under conditions where recrystallization did not take place. It was found that the kinetics of subgrain growth and of softening were similar, and that the correlation between subgrain growth and softening was in first approximation independent of the annealing temperature. It has been shown by Heidenreich' by means of electron transmission microscopy and by Hirsch and Kellar2 by means of an X-ray microbeam technique that the crystals of heavily cold-worked polycrystalline aluminum consist of subgrains of approximately 2µ diam, which are slightly disoriented with respect to each other. This substructure is found on cold working at room temperature, without annealing. A preliminary study has been previously published3 of the softening upon annealing at 350°C of a heavily cold-rolled aluminum single crystal. Softening and X-ray line sharpening for such a rolled aluminum crystal were later studied in more detail as a function of annealing time and temperature.4 Perryman5, 6 has studied the recovery of polycrystalline aluminum after cold rolling. By means of phase contrast microscopy he found that the subgrain size increases with the annealing temperature but does not alter very much with annealing time at a given temperature. In the present work further study was made of softening as a function of annealing time and temperature and subgrain sizes were determined by two different techniques in an attempt to find any correlation that may exist between softening and subgrain growth. Subgrain size measurements were made both by the X-ray microbeam technique and by transmission electron microscopy. EXPERIMENTAL PROCEDURE For the X-ray studies specimens were cut from

Jan 1, 1960

By T. M. Geffen, H. N. Hall

One-third to one-half of the original oil is left in most reservoirs even after thorough gas driving or waterflooding. In contrast, essentially all of the oil contacted con be recovered by flooding with a solvent (a fluid miscible with the reservoir oil). It is not economical to fill a reservoir with solvent since the value of the solvent would very likely exceed that of the oil. A practical method would be to inject a small bank of solvent to displace the oil. This solvent bank in turn could be driven through the rock by a less valuable scavenging fluid, such as natural gas which is also miscible with the solvent. Such a method of oil recovery was studied in the laboratory using long (up to 95 ft) core systems. It was found that, as the solvent moves through the reservoir, the front end of the solvent bank becomes mixed with the oil and forms a relatively short mixing zone between undiluted crude oil and pure solvent. An engineering correlation was obtained which can be used to predict the length of this zone. Displacement of the solvent by natural gas can be achieved with complete miscibility (above the critical pressure of the gas-solvent system at reservoir temperature) or with partial miscibility at lower pressures. Under conditions of complete miscibility, it was found that the length of the gas-solvent mixing zone could be predicted from the correlation developed for the solvent-oil mixing zone. With partial miscibility, two phases exist and the solvent is displaced by a modified gas drive in which vaporization and condensation occur. Equations are developed to predict the performance of this type of displacement. Two plans are suggested for application of miscible fluid displacement. one for miscible displacement of the solvent and the other applying to lower pressures where partial miscibility occurs during solvent displacement. Calculations based on the laboratory tests indicated that a bank of solvent with a volume of less than 10 per cent of the hydrocarbon volume under consideration will generally be adequate to obtain high oil recovery from the portion of the reservoir contacted in miscible fluid displacement. INTRODUCTION The conventional methods by which oil is displaced from reservoir rock—solution gas drive, conventional gas drive, and waterflooding—are all processes in which the oil is expelled from the rock by direct displacement with a fluid immiscible with the oil. Because of the immiscible type displacement, complete recovery of the reservoir oil is not achieved. In economically successful flooding operations, as much as 50 per cent of the original oil may be abandoned in the reservoir as unrecoverable. The use of a solvent (miscible with oil, such as LPG) as an injection fluid does not have the undesirable displacement features common to the use of gas or water (immiscible with oil). It can be readily appreciated, however, that it would not be economically feasible to displace the oil and entirely replace it with a solvent. A process was therefore devised for use in field operations in which only a small volume of solvent would be required to obtain essentially complete oil recovery in the portion of the reservoir contacted. In this process, the solvent acts as a buffer between the reservoir oil and injected gas, allowing the natural gas to displace indirectly the oil with much greater efficiency than if the gas displaced the oil directly. DESCRIPTION OF OIL RECOVERY PROCESS The solvent oil recovery process will be described in

Jan 1, 1958

By George Branner

THERE is no record of the commercial production of bentonite as such in Arkansas up to the present although fuller's earth has been. mined intermittently in the state1 from 1891 to 1922. Very nearly all of this was obtained from decomposed basaltic dikes.2 Recently three bentonite deposits of close stratigraphical relationship have been identified in the Coastal Plain region of southern Arkansas, which suggests that there may be a considerable quantity of commercial material available. LOCATION AND ACCESSIBILITY The three deposits are located respectively in the SE. ;1/4 SE. ;1/4 sec. 13, T.- 2 S., R. 13 W., Saline County, the SE. ;1/4 SE. 1/4 sec. 18, T. 5 S., R. 16 W., Hot Spring County, and in sec. 22, T. 12 S., R. 19 W., Ouachita County. The Saline County deposit is 14 miles by state highway 167 south of the city limits of Little Rock and 1 mile west by dirt road. This deposit is 12 miles south of Ward switch on the C. R. I. P. Railroad and 11 miles east of Vimy Ridge by dirt road. Vimy Ridge is also on the C. R. I. P. Railroad. The Hot Spring County deposit located in the SE. ¼ SE. ;1/4 sec. 18, T. 5 S., R. 16 W. is about 100 yd. north of Durian switch on the C. R. I. P. Railroad and on state highway No. 9, 5 miles southeast of Malvern. The Ouachita County deposit has not been accurately located but lies in sec. 22, T. 12 S., R. 19 W. It is approximately 2 miles by road from Chidester on the Missouri Pacific Railroad.

Jan 1, 1929

By Oswald J. Heinrich

IN this paper I shall attempt a description of the successful extraction of coal from this property after it had been on fire for probably fifty years, or more, and after attempts, made at various times, which had still left considerable coal behind. The Richmond coal-field has a well-founded bad reputation, arising from the circumstance that many of its collieries have had to be abandoned, from time to time, if not entirely, on account of fires, caused by spontaneous combustion, to which the character of the coal in this field renders them peculiarly liable. While I fully assent to the opinion that this trouble lies in the nature of the coal, which is highly bituminous, and the seams of which are, moreover, divided by slaty bands, through which, as also in the coal, iron pyrites is more or less disseminated, often in microscopically small particles, I must, nevertheless, declare that many lamentable disasters, causing great loss of life and property, could have been avoided if a suitable system of mining had been pursued in all the collieries. If this could not have been done from the be-. ginning of mining in this section of country (the history of which can be traced back to over one hundred years), at least experience enough existed upon this subject thirty and forty years ago to dictate the avoidance of the dangers to a considerable extent. I t is therefore necessary here to refer first, in a few remarks, to the character of the coal deposits, particularly in this immediate neighborhood, the Midlothian being one of the oldest and most extensive mines, and some of its coal being much subjected to spontaneous combustion. I must also refer to the history of former managements to explain more clearly the results which were arrived at. The Midlothian coal-mine property, situated upon the eastern outcrop of the basin, about four miles south from James River, exhibits

By H. Hu

Observations were made on the recrystallization of a 70 pct cdd-rolled silicon-iron crystal with an initial orientation of (113) [332]. Its polygonization and recrystallization characteristics were studied. Results indicated that re crystallization tendency of the deformed crystal is much weakened by the polygonization of the matrix. Complete recrystallization in such specimens is achieved by the growth of recrystallized grains of sufficient size and of the right orientations in relation to the matrix. Evidence was also furnished which suggests that the difference in the re-crystallization tendency is a result of the difference in the severity of lattice bending rather than the difference in orientation of the deformation texture. DUNN and Koh1,2 have made an extensive study on the rolling and annealing textures in silicon-iron crystals. Their results indicated that the recrystallization tendency can be widely different in crystals with different orientations. A particularly interesting example of their results was a crystal with an initial orientation of (113) [332], which developed a deformation texture of (001) [110] after 70 pct cold-rolling. Recrystallization in this crystal took long time anneals at high temperatures. Other crystals having different orientations recrystallized very rapidly. Wiener and corcoran3 have observed the retention of the (100) [011] deformation texture in a low-temperature annealed specimen of a commercial silicon-iron alloy, corresponding to areas of light-etching low-angle boundaries in the annealed struc-

Jan 1, 1960

By J. F. Radavich

Many heats of steel of low carbon value have been known to produce brittle pieces of steel. The brittleness is believed to be due to the impurities located within the grain boundaries. Such brittle steels have been examined with an optical microscope to ascertain the nature and the amount of the impurities present at the grain boundaries. Due to the relatively low resolving power of the optical microscope, the impurities are not visible in fine detail. The writer obtained some sheet steel and proceeded to determine the location of the impurities and to show the application of the electron microscope to the study of grain boundaries. One sample was known to be capable of becoming embrittled, whereas another sample was believed to be much less susceptible to embrittlement. Treatment of Specimens The specimens were embrittled by annealing above the A3 point under mildly oxidizing conditions. One piece of ingot iron could not withstand a 90" bend, whereas another piece of ingot iron was not affected and could withstand a 90" bend. The brittle piece was then annealed at a high temperature in a hydrogen atmosphere. The annealed ingot iron was termed cured and could withstand a 90" bend very easily. The three specimens examined will be designated as brittle, good. and cured in the discussion that follows. Procedure The sizes of the specimens were as follows: one piece of brittle ingot iron-3/8 by 35 in.; one piece of good ingot iron-96 by 1/8 in.; one piece of cured ingot iron-36 by 54 in. The specimens were too small to be polished by hand and therefore were mounted in bakelite. The polishing procedure was carried out in the conventional manner with the use of 1/0 through 3/0 papers, and the final polish was done with alumina on a billiard cloth. The specimens were then etched in a 4 pct solution of picral in alcohol, and then they were examined through an optical microscope. An area was chosen that showed distinct grain boundaries, and an effort was made to keep near this area when pulling the replicas REPLICA TECHNIQIJE The replica technique used in the preparation of the replicas for examination under the electron microscope is described in Electron Metallography.' It consists essentially of the following steps: 1. Obtaining a suitably etched specimen. 2. Applying a swab of ethylene di-chloride on the surface. 3. Applying a formvar solution on the surface. 4. Placing a screen on any desired spot. 5. Breathing on the fornivar layer. 6. Applying scotch tape on the screen and film. 7. Pulling the film and the screen up with the Scotch tape. 8. Separating the screen from the Scotch tape. This replica technique is very similar to the one described by Harker and Shaefer. However, with the added step, the percentage of replicas removed is very much higher regardless of the length of the time from the etching of the specimen to the actual pulling of the replica. The replicas were then shadow cast with manganese at a filament height to replica distance ratio of 1 1/2:7. This produced a very high contrast replica for use in the electron microscope. One of the dificulties encountered with this study was the restricted area of the specimen. The width of the specimens was the same as that of the 200 mesh nickel supporting screen. In order to increase the effective area, the screens were cut down as shown in Fig 1. The arrow indicates the direction in which the replica was pulled. This operation made it possible to obtain a large percentage of good replicas. Fig 3 shows an electron micrograph of a brittle piece of ingot iron and a grain boundary that was polished mechanically. The surface is very rough probably due to the incomplete removal of the flowed layer by the picral etchant. The grain boundary does show evidence of impurities. It was decided to electropolish the specimens to obtain a much smoother surface than the one obtained by mechanical polishing. ELECTROPOLISHING The specimens were cut in half to expose the metal on the back side. The exposed metal had sufficient area to make good electrical contact and electropolishing was carried out easily. The conditions for electropolishing were 0.9 amp, 35 volts, and 25 sec. in an electrolyte composed of 850 cc of ethyl alcohol, 100 cc distilled water, and 50 cc of perchloric acid. The polished specimens were then etched in the 4 pct picral solution for a shorter time than was necessary for

Jan 1, 1950