Search Documents

Jan 1, 1885

By F. H. Deily, H. W. Lownie, E. A. Loria, L. W. Ledgerwood, M. W. 207-000-000-012 Mallett, J. E. Eckel

MANY investigations have been made of the residual gas content of iron and steel. Very few, if any, quantitative measurements have been made on the oxygen content of cupola-melted iron.' The fact that cast iron is a complex alloy rather than

Jan 1, 1957

By Wayne E. Glenn, R. W. French, Lincoln F. Elkins

The Lance Creek Sundance reservoir provides a case history of ro years performance of a reservoir in which unit operation has permitted effective utilization of gravity drainage augmented by primary pressure control with injection of gas into top structural wells. Detailed performance of the reservoir is presented by means of maps of Well status, reservoir pressure, individual well recovery, etc., and by pool-performance charts. Analysis of reservoir performance indicates only minor water encroachment, so that gravity, injected gas, and expansion of gas are the main oil-expulsive agents. A simplified theory of regional drainage of oil from upstructure location to downstructure location due to gravity is presented and checked by means of comparison of "reservoir" permeability and "well" permeability from the pool performance. Good order of magnitude agreement was obtained. Individual well performance and overall reservoir performance indicate possibility that maintenance of pressure makes ineffective those parts of the reservoir in which permeability is too low to permit effective drainage of oil by action of gravity. Oil from these parts can be recovered only when pressure is reduced locally by selective withdrawal or when overall reservoir pressure is finally reduced.

Jan 1, 1949

By H. Ries

INTRODUCTION OF the several interesting physical properties of clay which have claimed the attention of investigators in recent years, none is more important than the behavior of the material when heated to temperatures above those of dehydration. Some of the problems to be solved are: 1. The mineralogical changes that take place in firing. 2. The relation between temperature and change in constitution, shrinkage, porosity, etc. 3. The importance of the time factor, as duration of firing, either in reaching a given temperature, or of exposure to a constant temperature. Mineralogical Changes As a result of fusion, reactions take place between the constituents of a clay, which results in a reorganization of the mass, and the formation of new compounds. Of the new minerals developed, sillimanite is the one usually recorded, and has been referred to by a number of observers.1 There appears to he a difference of opinion, however, regarding the temperature at which it is formed. Thus. Klein2 notes that sillimanite forms only above. 1300° C., while Mellor claims that it can develop below 1200° C., the difference in results being conditioned by the time factor. In Klein's experiments the test pieces were fired in 12 hr., while in Mellor's, the temperature rose from 800° to 1180° in 24 hrs., and occupied the same time in cooling back to 800°.

Jan 9, 1917

By D. C. Hilty, W. Crafts

A qualitative pseudoternary solidification diagram for the Fe-S-O system modified by manganese is proposed and supported by experimental derivation of an isothermal section at 1475°C and substantially 1 pct Mn in the solid-metal phase. The solubility of oxygen in liquid iron containing 1 pct Mn and sulphur contents up to 0.9 pct has been measured at 1600°C and found to increase as the sulphur content exceeds 0.15 pct. AS has been pointed out previously,' all oxide and sulphide inclusions in steel, excluding mechanically entrained matter, result from modifications of the basic Fe-S-O system. Therefore, one method of attack on the problem of the mechanism of deoxida-tion and inclusion formation is to examine the influence of deoxidizers on the Fe-S-O liquidus diagram. This approach has been adopted in work on the subject being carried out at the Metals Research Laboratories of the Electro Metallurgical Co. and has resulted in the postulation of types of solidification diagrams for the Fe-S-O system modified with common deoxidizers. This method has been of considerable assistance in interpretation of the factors affecting the formation of inclusions.' For the most part, however, these diagrams have been highly speculative. They were constructed primarily by inference from the pertinent binary and ternary systems and from the appearance of inclusions produced by specific deoxidizers. Moreover, since the systems contain four or more components, simplifying assumptions and qualifications were necessary in order to permit their representation as modifications of the Fe-S-O diagram. Consequently, experimental confirmation of the type of construction employed for these diagrams is desirable, and the present paper is concerned with such evidence. The addition of manganese to the Fe-S-O system was selected for initial investigation. Manganese is an important component of practically all steel and is, therefore, of fundamental interest. Because of its great affinity for sulphur, manganese has a more profound effect on the sulphide side of the Fe-S-O diagram than any of the other common deoxidizing eletments. In addition, more quantitative information pertaining to the contiguous binary and ternary systems involving iron, manganese, sulphur, and oxygen is available than for the other deoxidizers. Fe(Mn)-S-O Solidification Diagram Many of the side diagrams of interest in connection with this system are known. The Fe-Mn binary has been well established by several investigators;% the Fe-O system has been clarified by Darken and Gurry;' and FeO-MnO diagrams have been published by Herty,5 Andrew, Maddocks, and Howat,6 and by Hay, Howat, and White.7 The Mn-O diagram does not appear to have been derived experimentally, but the portion of 'it that is of interest can be visualized easily from a consideration of the melting points of Mn and MnO and the fact that a broad miscibility gap must exist between them. The ternary Fe-Mn-O diagram has been discussed by Benedicks and Löfquist,8 Wentrup,9 and by Körber and Oelsen.10 Experimental study of the Fe-Mn-O system has been carried out by Körber and Oelsen and to a lesser degree by Chipman, Gero, and Winkler,11 Hilty and Crafts," and others. On the basis of published information, then, an outline of the Fe-Mn-O liquidus diagram can be constructed as illustrated by Fig. 1. In this, as in all succeeding diagrams, transformations such as the ?-? reaction in iron have been ignored for purposes of simplification. The arrows denote falling temperature. The distinguishing feature of this diagram is the broad region of liquid immiscibility extending

Jan 1, 1955

By C. D. Hall, F. E. Dollarhide

Fluid Ioss agent.s for crude oil and for water have been studied in dynamic tests. A treatment using a spearhead with a fluid loss agent followed by plain fluid appears feas ible in crude oil, but not in water. An equation for spearhead depletion shows that spurt loss relative to fracture width must be low, if the portion of spearhead fluid in the treatment is to be small. The presence of colloidal matter in crude oils aids the fluid Ioss agent. Unlike in kerosene, where flow limited the agent deposition, in crude oils the filter cake continually formed and leak-off declined. The volume-time relation varied somewhat for different crudes, but was best described by a square root of time function. Spurt loss was inversely proportional to agent concentration. After the fluid loss agent initiated the filter cake, the crude oil colloids built on it effectively. A 2-minute or a 5-minute spearhead with double the normal agent concentration gave the same fluid Ioss curve as the same concentration did for a 30-minute test. The agents tested in water gave fluid Ioss plots on which, for the first few minutes, volume was proportional to the square root of time, but later became proportional to time. For fracture area calculation the customary square root of time function is a satisfactory approximation. Leak-off rates and spurt losses were higher in water systems than in oils. The spurt Ioss tended to be inversely proportional to concentration. In spearhead tests, the filter cakes were not eroded by water flow. However, the rather high spurt loss values make spearhead treatments impractical for water-based fluids. Introduction The effects of dynamic testing conditions on the performance of fluid loss agents in kerosene have been studied previously.' We have extended the work to include crude-oil- and water-based fracturing fluids. An understanding has been gained of the mechanisms of formation and functioning of the filter cakes of fluid loss agents. The practical aspects of evaluating performance of agents in relation to fracture area calculations also are considered. The feasibility of using the fluid loss agent in a spearhead stage of the treatment is examined further for both types of fluids. Experimental Procedure The dynamic fluid loss tests were performed in an apparatus similar to the high-pressure apparatus described in a previous publication.' A fracturing fluid was circulated over a rock surface located in a closed pressurized loop. The fluid flowed axially over the cylindrical surface of a core 2 in. in diameter X 3.5 in. long, mounted (with the flat ends sealed off) in a pipe, with 0.117 in. annular clearance. The filtrate was collected in a central hole in the core and led through valves to graduated cylinders. Provision was made for changing quickly the circulating fluid during the test (spearhead runs) without interrupting the filtration pressure. The only modifications were to add heating tapes and water jackets for the tests with crude oils, all conducted at ISOF, and to change all parts exposed to the test fluid to stainless steel for the tests with water-based fluids. The latter tests were made at room temperature, 80F. Three crude oils were tested. A mixed crude, obtained from a local refinery, contained a considerable amount of light ends. For safety reasons, it was stripped to 250F vapor temperature before use in the fluid loss tests. The other two oils were used as obtained from lease tanks. One was a greenish-brown, 37" API paraffinic crude, and the other was a black, 32" API asphaltic crude. The fluid loss agent for oil, here designated for brevity as Agent A, was Adomite@ Mark II*, a granular solid commercial agent, the same as previously tested in kerosene.' Three different compositions of fluid loss agents were tested in Tulsa tap water. Agent B was adomit& Aqua*, a solid commercial fluid loss agent, comprising clays and hydrophilic gums principally derived from starch. Agent C was a mixture of three parts of Agent B with two parts of silica flour. Agent D was Dowel1 J137, a mixture of guar gum and silica flour. The test cores were cut from contiguous blocks of Berea or Bandera sandstones. For the oil tests, the cores were oven dried, evacuated, saturated with kerosene, and the kerosene permeability was measured. The cores used with the water-based fluids were pretreated by saturating with 3 percent calcium &loride solution to minimize pemeability damage by the fresh water due to clay migration. The

Jan 1, 1969

By Ian William Wark

DIFFERENT parts of the world in which mineral separation by flotation is practiced experience vastly different natural temperatures, and in some districts there is a big difference between summer and winter tempera-tures. It will be shown in this paper that the temperature is of con-siderable importance where it is desired to separate pyrite or arsenopyrite from other minerals. It is probable that some of the differences obtained in the flotation of these minerals at plants working under otherwise similar conditions are due to temperature variations. The influence of temperature on the flotation of galena, chalcopyrite and sphalerite by xanthates is less marked than its influence on pyrite flotation.

Jan 1, 1938

By F. R. Hensel

The present study was made to determine the laws governing the formation of the primary? crystal structure during solidification. Most of the experiments were carried out on chill castings, but from the resiilts it will be possible to draw certain conclusions as far as sand castings are concerned. It is necessary to discuss first a number of theories, which are generally adopted for explaining the structure of an ingot. Usually, the structure of an ingot consists of the following three zones (Fig. 1): (1) a chill layer of small at-random oriented crystals; (2) a layer of columnar crystals; (3) a zone of equiaxed crystals. The tensile properties of the chill layer and the equiaxed range are usually much better than in the columnar range, particularly the planes that are formed by the columnar crystals growing from two sides at right angles have low tensile properties. This is one of the reasons why columnar crystals in ingot structures are undesirable.

Jan 1, 1937

By John H. Hollomon, C. Zener

It is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect to rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. Earlier Investigations A clear analysis of the conditions necessary for plastic flow and for fracture was first given by LudwikI1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis. both a Flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracturc is less than the flow stress and ductile if the reverse is true. According to Ludwik's analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence of tlow stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated3 by the authors. According to this principle of equivalence, strain rate e and temperature T affect the flow stress only through a single parameter-p of the form: p = eeQ/RT 111 In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. article of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

By C. Zener, John H. Hollomon

It is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect to rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. Earlier Investigations A clear analysis of the conditions necessary for plastic flow and for fracture was first given by LudwikI1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis. both a Flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracturc is less than the flow stress and ductile if the reverse is true. According to Ludwik's analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence of tlow stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated3 by the authors. According to this principle of equivalence, strain rate e and temperature T affect the flow stress only through a single parameter-p of the form: p = eeQ/RT 111 In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. article of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

By C. W. Vaupell

The Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resurgence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barccnite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available. Introduction The Huitzuco mercury mines are of interest because of the unusual occurrence of ore in extinct geyser vents and the presence of several rare mercury minerals. Some of the deposits have typical characteristics of the telethermal zone and there is a gradation towards typical epithermal mineralization in depth. Halse,1 Villarel1o,2 Mactear3 and Merri114 have described the geology and the early operations in the district, and Bar-cena5 and Mallet6 have described the rare mercury minerals, livingstonite and barcenite, found at Huitzuco. Location The village of Huitzuco lies in the north central part of the State of (Guerrero, Mexico, 27 km. (16.7 miles) east of Iguala, which is the largest and most important town in the area. Iguala is served by the Mexican National Railways and also by the Mexico City-Acapulco highway. The highway is surfaced from Mexico City to Iguala, a distance of 200 km. (124 miles) by road, and there is a fairly good, level, dirt road from Iguala to Huitzuco. The elevation above sea level is about 1000 m. (3280 ft.). The climate is warm and very dry except during the rainy season, from June to

Jan 1, 1941

By C. W. Vaupell

The Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resurgence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barccnite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available. Introduction The Huitzuco mercury mines are of interest because of the unusual occurrence of ore in extinct geyser vents and the presence of several rare mercury minerals. Some of the deposits have typical characteristics of the telethermal zone and there is a gradation towards typical epithermal mineralization in depth. Halse,1 Villarel1o,2 Mactear3 and Merri114 have described the geology and the early operations in the district, and Bar-cena5 and Mallet6 have described the rare mercury minerals, livingstonite and barcenite, found at Huitzuco. Location The village of Huitzuco lies in the north central part of the State of (Guerrero, Mexico, 27 km. (16.7 miles) east of Iguala, which is the largest and most important town in the area. Iguala is served by the Mexican National Railways and also by the Mexico City-Acapulco highway. The highway is surfaced from Mexico City to Iguala, a distance of 200 km. (124 miles) by road, and there is a fairly good, level, dirt road from Iguala to Huitzuco. The elevation above sea level is about 1000 m. (3280 ft.). The climate is warm and very dry except during the rainy season, from June to

Jan 1, 1941

By Carlos E. Roggero

The influence of high temperatures on the zinc roasting practice has been investigated by full-scale tests in fluid bed reactors operating at temperatures from 950° to 1150°C. It was definitely shown that, throughout the range, an increase in tem perature resulted in a 2 to 3 pct increase in zinc solubility because of decreased content of zinc fer-rite and lowered sulfide sulfur. The former is attributed to thermal decomposition of ZnFe,O,, and the latter to increased oxidation rates, ad longer retention times. Data on the gveatly increased volatilization of lead, cadmium, and silver above 1000°C, are presented. A considerable fraction of the iron present in the feed was also transferred at high temperatures from the coarse roaster discharge to the flue dusts. AS part of its metallurgical complex1-3 situated in a 12,000 it Andean valley at La Oroya, Peru, Cerro de Pasco Corp. (a wholly owned subsidiary of Cerro carp.) operates a 150 short ton per day electrolytic zinc refinery. Electrolysis is carried out at a cathode current density of 65 amp per sq ft with an electrolyte content of 55 g per liter of Zn and 150 g per liter of su lf uric acid. Due to the high iron content of the marmatitic concentrate used, a large fraction—about 15 pct—of the zinc reports in the leach residues. To minimize such losses, efforts have been exerted toward improving calcine solubility. One method, as noted in the literatre,, is to retard zinc ferrite formation by decreasing the roasting temperature. Unfortunately, such a procedure tends either to reduce the roaster throughput or increase the sulfide sulfur in the calcine. Consequently, this approach was discarded in favor of experimental work in the opposite direction, i.e., high temperature roasting. Full- scale tests were promising and resulted in the granting of a patent to Cerro de Pasco carp.' After a brief account of plant equipment and operating procedure, this paper describes the tests made and attempts to assess the results obtained. GENERAL PLANT LAYOUT AND OPERATION The Roasting Plant, see Fig. 1, comprises an agglomerating plant feeding three fluid bed roasters with a combined capacity of 10,000 tons per month. The Peruvian patent rights on this process were purchased from the New Jersey Zinc Co. The concentrate, assaying: is pelletized to a -3 +14 mesh product and fed to the fluid bed roasters. The roaster exhaust gases pass through a waste heat boiler, cyclones, a fan, and an electrostatic precipitator. Approximately half of the dust collected in the cyclones returns to the pellet-izing plant as one of the binding ingredients, the remainder joins the cooled bed discharge ('overflow') and is conveyed to the grinding plant. The -35 mesh product obtained, together with the dust collected in the electrostatic precipitator constitute the feed to the leaching plant. Batch leaches are made in vessels with mechanical and air agitation, the residues are separated and washed in Burt Filters, and pumped to storage ponds. THE FLUID BED ROASTERS Two reactors are as shown in Fig. 2, and the third,' of about the same configuration, is approximately 40 pct smaller. The total grate and freeboard (just below the gas outlet) areas measure 170 and 426 sq ft respectively. The feed, continuously weighed and controlled by Merrick Weighto-meters fitted with variable speed motors, enters the reactors at the top of the expanded bed level. The coarse calcine overflows through the opposite end by

Jan 1, 1963

By Norman B. Pilling

Practical limitations to the usefulness of silicon steels are the hardness and brittleness silicon imparts to iron, making iron-silicon alloys of more than 8 per cent. silicon content unusable except where castings can be employed. In the use of commercial silicon steel, in thin rolled sheets, as in transformer construction, when the silicon content exceeds 4.2 per cent. the sheet is too brittle for satisfactory shaping by punching or similar operations. When such a brittle steel is sheared, it frequently breaks along a haphazard path in advance of the cutting tool. In Fig. 1 is shown a slightly enlarged view of the sheared edge of a 14-mil enameled sheet of nominally 4 per cent. silicon steel. In 5 in. along the sheared edge, only 44 per cent. was actually cut; the rest was torn, with the path of fracture varying widely from the path of travel between the shears. This is probably an extreme case of such brittle-ness, but a shearing or punching test is not necessary to reveal brittle-ness of this order; narrow strips will break when bent between the fingers. In Fig. 2, the proportion of actual cut edge is greater, but secondary fractures branch off at about 30" from the line of shearing in advance of the cut. Deprived of the support of adjacent parts of the sheet, the tips of the angles are bent out of the plane of the sheet by the shears, leaving a peculiar flared effect, like the set of the teeth on a saw. An end-on

Jan 1, 1923

By R. L. Wiegel

The two questions considered in this study are: (1) what similarity is there in the liberation of magnetite from various iron formations, and (2) how is this liberation affected by the size reduction technique employed. Twelve sample suites were obtained from commercial concentrators processing magnetite iron formation in the United States, Canada, and Australia. These samples have grades in the range 15 to 45% magnetite iron and approximate mineral grain sizes o f 50 to 2000 microns. Efforts were directed at measuring the liberation characteristics of the samples obtained from the concentrators primary grinding mills. The Davis tube, a laboratory magnetic separator, was used to concentrate individual size fractions of the size reduction product to determine liberation data. These liberation data were compared with relationships calculated from a highly idealized mathematical model of liberation in a binary mineral system. The results of these comparisons have been encouraging for nine or ten of the twelve samples tested. This leads to the conclusion that for most commercial iron formations, at least with conventional rod mill size reduction, it is possible to quantitatively characterize liberation with two parameters: an effective mineral grain size and ore grade. Limited laboratory size reduction tests as well as one of two sets of liberation data from commercial primary autogenous grinding lend some support to the contention that autogenous grinding can affect mineral liberation.

Jan 1, 1976

By Norman B. Pilling

Practical limitations to the usefulness of silicon steels are the hardness and brittleness silicon imparts to iron, making iron-silicon alloys of more than 8 per cent. silicon content unusable except where castings can be employed. In the use of commercial silicon steel, in thin rolled sheets, as in transformer construction, when the silicon content exceeds 4.2 per cent. the sheet is too brittle for satisfactory shaping by punching or similar operations. When such a brittle steel is sheared, it frequently breaks along a haphazard path in advance of the cutting tool. In Fig. 1 is shown a slightly enlarged view of the sheared edge of a 14-mil enameled sheet of nominally 4 per cent. silicon steel. In 5 in. along the sheared edge, only 44 per cent. was actually cut; the rest was torn, with the path of fracture varying widely from the path of travel between the shears. This is probably an extreme case of such brittle-ness, but a shearing or punching test is not necessary to reveal brittle-ness of this order; narrow strips will break when bent between the fingers. In Fig. 2, the proportion of actual cut edge is greater, but secondary fractures branch off at about 30" from the line of shearing in advance of the cut. Deprived of the support of adjacent parts of the sheet, the tips of the angles are bent out of the plane of the sheet by the shears, leaving a peculiar flared effect, like the set of the teeth on a saw. An end-on

Jan 1, 1923

By Paul Billingsley

The term Boulder batholith was first applied in 1897 by W. H. Weed2 to the extensive mass of granite in western Montana within whose borders occur the ore deposits of Butte. In a general way this was known to extend from Helena on the north to the Highland Mountains near Butte on the south, and to be relatively narrow in its east-west diameter. Its intrusive relations to the surrounding sedimentary rocks, and its probable Tertiary age, were described by Weed, but in many ways his statements, based upon incomplete data, have required revision. Most notable of the errors of this description of the batholith were the failure,3 since corrected, to recognize the intrusive contact of the granite with the capping of andesite, and the complete absence of any reference to the many extensions of the granite beyond the somewhat narrow limits of its largest exposure.

Jan 1, 1915

By W. G. Wender

This report covers the area producing from limes and sands of Pennsylvanian age, roughly embracing the territory between the Red River on the north and the Llano Mountains on the south, and between Fort Worth on the east and Abilene on the west. It includes Archer, Cooke, Montague, Wichita, Wilbarger, Clay, Baylor and Foard counties in the North Central Texas or Red River Basin area, and Brown, Callahan Coleman, Comanche, Eastland, Erath, Palo Pinto, Stephens, Shackel-ford, Throckmorton, Young and Jack counties in the West Central Texas area. Furthermore, it includes a brief review of development in Jones, Runnels, Haskell and Fisher counties. North Central and West Central Texas during the year 1928 produced an approximate total of 50,948,7461 bbl. or oil. This represents a decrease of approximately 7,720,250 bbl. under 1927 total production. This decrease was due to a slump in production in Brown, Archer, Wichita, Stephens and Cooke counties. Brown County showed the greatest decrease. The 1928 prodction in this county was approximately 4,500,000 bbl. less than the 1927 production. Gross production during 1929 in the North and West Central Texas area can be expected to be lower than in the year 1928. Only one county showed a considerable increase in production. Wilbarger County production increased approximately 3,000,000 bbl. during 1928. Its daily average increased from 9000 bbl. in April to 36,000 bbl. in August. At the close of 1928 it was averaging close to 32,000 bbl. daily. Drilling activity in North and West Central Texas during 1928 showed but a slight increase in completions. The total number of completions during 1928 was 3902, of which 2094 (53 per cent.) were producers, as compared to 3805 completions and 2112 (56 per cent.) producers during 1927. Brown, Young, Wichita, Archer and Wilbarger counties were the leaders in development. The outstanding discoveries for the districts were the Consolidated pool, extensions in the Greyback pool of Wilbarger County, and the Stephens pool, Fisher County.

Jan 1, 1929

By C. R. Ince

The term "differential flotation" is used to denote a flotation operation in which separation is effected between two or more minerals of the same class; e. g., lead sulfide from zinc sulfide, pyrite from blende, chalco-pyrite from pyrite, chalcopyrite from blende. At present, so far as published work shows, there seem to be two theories as to the mechanics of differential flotation. The earlier and more generally accepted theory is that the so-called depressing agents alter the surface of one or more of the sulfides in the ore, either by chemical action or adsorption, so that it is no longer amenable to flotation, but that these depressed sulfides can be revived, after the unaffected sulfide has been floated, by reagents which react chemically with the altered surface and make it amenable to flotation. More recently, Professor Taggartl has advanced the theory that slime adsorption is an important factor in differential flotation. He believes that, with the proper use of a class of agents, which he calls dispersion agents and which include practically all the depressing agents, one can cause the slime to adsorb differentially on sulfide surfaces. A gangue-slime coated sulfide surface will act as a gangue particle and will not float. If, subsequently, an agent that will remove the gangue-slime coating is added, the sulfide again assumes its original surface and can be floated as an ordinary sulfide. This is the basis of the slime theory of differential flotation. Timber Butte mill at Butte, Mont., is a typical lead-zinc flotation concentrator. Neihart ore, chosen for investigation in this work, is one of the custom ores treated at that mill. Practice at Timber Butte mill in February, 1928, was as follows: A combined lead-zinc concentrate was first made using 0.2 Ib. per ton on the ore of potassium xanthate and 0.03 lb. per ton of Cleveland Cliffs oil after 1.5 lb. per ton of lime and 1 lb. per ton of calcium chloride has been added just before the ball mill. The concentrate was then thickened to 70 per cent. solids. Potassium cyanide to the amount of 0.3 lb. per ton and zinc sulfate in the quantity of 0.5 Ib. per ton were added to the thickened pulp and the whole

Jan 1, 1930

By C. E. Jackson, E. C. Nelson, A. L. Christenson

Much information regarding the transfornlatio~lal characteristics of a steel as it cools in a known manner from the austenitic state can be obtained from dilatometric studies. This method has received more arid more attention because of its great flexibility, accuracy, and ease of interpretation. 'The method is entirely applicable to any rate of heating and cooling although the experumental procrdures for high rates of cooling have offered some difficulties. This paper presents a description of equipment employing cooling rates up to 500 °C. per secorld and the results of dilatometric observations on six commercial steels are included. French and Klopsch1 studied the cooling transformations of a serirs OF carbon steel, using the thermal arrest method. This was followed by the systematic investigatiol1 of Esser and co-workers on the effect of carhon2 and other alloying additions. in which the transforlnation temperature\ were determined by magnetic induction measurements indicated by a string galranoineter. Emphasis was placed on determining Ar' trailsformations and the critical cooling rates for these steels. The maglietic measurements wrere used in an effort to obtain more accurate data at higher cooling rates. Measurements of thermal arrest were made also to check the validity of the magnetic indications, and good correlation was found between the two, although Esser's,Ar' temperature measurements on iron-carbon alloys were about 200°F. lower than the measurements made by Fresnch and Klopsch. A notable contril~ution by Esser was the introduction gas quenching. wever and Rose4 used a moving-coil galranometcr in the study of the .Ar and Ar" of iron-carbon alloys by the thermal arrest method and obtained somewhat lover Ar" temperatures than those observed by Esser below I per cent carbon and considerably higher ahove. They concluded that the cooling rate had little influcncc on the Ar" temperatures above 0.4 per cent carbon, although Esser had observed a decrease in the -4r" temperature with increasing cooling rate with similar steels. Digges determined the .Ar" temperature4 for a scries of high-purity iron-carbon alloys, and close agreement with his results was obtained by Greninger. The thermal arrest method. together with metallographic observation used in both these studies, represents the latest investigations of this type. Any investigation by thermal analyses is dependent on the heat of reaction and the specific heat of the

Jan 1, 1945