Search Documents

By Edward W. Mehal

This paper presents a review of the technologies which have been used in the application of III-V compound semiconductors to integrated circuits and arrays. These materials have properties which make them useful for various devices such as: light emitters, sensors, microwave sources, and microwave diodes. Technologies for incorporating these devices into integrated circuits have been reported and processes developed for fabricating planar devices using selective epitaxial deposition or selective diffusions. Isolation methods utilizing semi-insulating GaAs, oxide isolation, and ceramic insulation have also been reported. These techniques, and the devices and circuits produced or proposed are discussed. AFTER the invention of the silicon-integrated circuit, methods for utilizing compound semiconductors for integrated circuit applications were proposed. The scope of applications was potentially much broader because of the range of properties available from these materials. There also was the opportunity of coupling these properties with germanium and silicon devices to realize functions and circuits which could not be produced with silicon monolithic circuits. Table I exemplifies the range of electrical properties available in III-V compound semiconductor materials which are currently being widely used. A wide range of sensor and emitter applications result from the range of band gap. The band structure of GaAs and GaAsxP1-x permits their use as microwave oscillator source, and the high electron mobilities further facilitate their utility in microwave devices. The concept of "integrated functions"1 results from the availability of these materials and methods for utilizing their special properties. Heteroepitaxial growth allows the fabrication of a monolithic block of these materials. Semi-insulating GaAs permits the attainment of electrical isolation between components in a monolithic block without resorting to p-n junction biasing or oxide isolation methods. An "integrated function" is a unit which can perform a system or subsystem role and perform a number of electromagnetic functions. These functions could include sensor or input transducer, signal processing, interconnections, and control or output function. Two examples which demonstrate this concept are an optoelectric processor and a microwave receiver front end. The optoelectronic processor, Fig. 1(a), would consist of a light sensor, signal processor, and output emitter. The sensor could be InSb or InAs which would be IR-sensitive. The signal from this sensor would then be amplified and transmitted to the light emitter. The amplifier could utilize GaAs bipolar or field effect transistors. A Gap emitter would then produce visible radiation. The microwave receiver front end, Fig. l(b), would consist of a local oscillator section and a mixer section. A signal input from an antenna is mixed with the signal from the local oscillator. The local oscillator signal is produced by a Gunn oscillator. The single-ended mixer utilizes one Schottky barrier mixer diode. The IF signal would then be amplified further and suitably displayed. A further extension of the capability of utilizing the

Jan 1, 1969

By George W. Harris

In the earlier period of anthracite-mining, much coal was wasted, both underground and in the culm-banks on the surface. Such waste is common in the development of new mining-districts, in which, as a rule, only the richest material can be profitably treated. In the anthracite-region, special causes operated to increase this evil. The mines were generally worked under 20-year leases, and royalties were paid upon such coal only as was actually marketed. The lessees consequently cared for immediate profit solely. They were not bound to win all the coal they exposed, or to leave it in such condition that their successors could win it. Nor was it their interest or duty to educate consumers in the use of their product. The market called for coal of large sizes; and such coal they furnished, throwing away the rest. Any pains taken by them to bring about a more rational use of coal by their consumers would have borne fruit, after their leases had expired, to the benefit of somebody else. A full statement of the situation was given in 1893, in the report of the State Commission, appointed in 1889 to investigate the subject.' That body included the names of Heber S. Thompson, William Griffith and the late Eckley B. Coxe.2 Its report gives special attention to the utilization of the old culm-banks.

Jan 1, 1906

By Elmer R. Kaiser

COMBUSTION of coal and transfer of heat from flames and gases to boiler surfaces continue to be of great interest to engineers here and abroad. Numerous investigations have been in progress to improve furnace and boiler performance and economy. The importance of better understanding of the processes and opportunities for improvement is apparent when it is remembered that heat from at least 500 million tons of coal a year the world over is being transferred to boiler water at efficiencies ranging mostly between 50 and 90 pct. Even slight gains in efficiency, economy, and labor saving become very significant when multiplied by the enormous quantity of fuel consumed. Also the competitive position of the large coal, oil, and gas industries in satisfying the fuel consumers is greatly affected by the achievements made through technical progress with each fuel. This paper is part of a continuing activity of Bituminous Coal Research, Inc., to extend the knowledge of coal utilization for steam generation and to seek promising directions for future research and development in cooperation with others. Particularly in the latter regard, numerous interviews were held during the last three years to seek the experience and advice of boiler and combustion- equipment manufacturers, electric-utility executives, and fuel engineers. A wealth of published information was also reviewed, which together with the interviews pointed to the advisability of further work on ash and sulphur control.

Jan 3, 1954

By G. P. Boomslitter

In previous discussions on stresses in hoisting ropes, little has been said concerning the effect of the elasticity of the rope itself on the stresses due to acceleration. Laschinger1 has calculated acceleration stresses for several cases but he has ignored the elasticity of the rope as a factor, except as it compresses the drum and stretches itself as it winds thereon. He also deals with steam plants and he shows the effect of the "jerky" start of the engine. This effect would actually be reduced by the elasticity of the cable. With the advent of the motor-driven hoist, new conditions have arisen. The jerk mentioned by Laschinger has been eliminated and smoother starting made possible. But the elastic properties of the rope seem to introduce considerable periodic acceleration stresses in the rope. The following discussion of acceleration stresses is based on the assumption of a constant acceleration at the drum. To be exact, the mathematical work is based upon the assumption that the top is moving upward with a constant acceleration, and ignores the fact that the cable is shortening as it winds. However, the effect of the shortening would be inconsiderable during the first part of the acceleration period. Most hoisting engineers make the assumption of constant acceleration at the drum. Under the older method of calculating acceleration stresses, this would be true with a constant torque motor. But if stresses vary, as this paper attempts to show that they do, constant torque would not give constant acceleration, although the velocity-time curves obtained in the full size test herein described showed that they approach rather closely to this condition, at least as nearly as could be measured. Theoretical Discussion According to elementary physics, the force required to accelerate a Wf body of weight W at the rate of f ft. per sec.2 is wf . To raise the body Wf with acceleration of f ft. per see.2 the total force required is I + Wf, in if

Jan 1, 1927

By R. C. Gould, A. M. Skov, L. F. Elkins

Comparison of long term decline in oil production during cyclic waterflooding or pressure pulsing of part of the Driver Unit with steady injection-imbibition flooding in the Tex Harvey area led to large expansion of flood in the Driver Unit on the steady injection basis. While the flood has been successful, the major problem has been attainment of satisfactory oil production rates in most of the wells. Large volume fracture treatments of low capacity wells were unsuccessful in achieving sustained increases in production. A two-section area in the Driver Unit has already recovered 620 bbl of oil per acre by waterflood but other areas have not performed so well. Sun Andres water containing 300 to 500 ppm H,S is sweetened to 0.5 to 1 ppm H,S by extraction with oxygen-free flue gas. This prevents contamination of gas produced in the area and apparently it has reduced corrosion in minimum investment, thin-wall, cement-lined water dktribution systems. Cement-lined tubing in injection wells has mitigated corrosion as effectively as thick polyvinyl chloride films have, and at less cost. Introduction As reported in the literature the Spraberry field of West Texas has presented unusual problems for both primary production and waterflood ing. Earlier information from the Spraberry Driver Unit included conception and evaluation of cyclic waterflooding or pressure pulsing in a nine-section pilot test as an aid to extraction of oil from the tight matrix rock and as a boost to normal capillary imbibition forces An additional 5 years' operation in that area, and performance of expanded steady injection water-flood, now covering a total of 68 sq miles, are reported herein. In addition, since the Driver Unit is one of the largest waterfloods in areal extent in the U. S., many operating experiences are presented for the benefit of engineers concerned with operation of other Spraberry floods or with other waterfloods where this reservoir technology and/or water handling technology may be adaptable in part. These include: (1) attempts to improve producing well capacity through large volume fracture treatments, (2) long-term performance of water treating plants utilizing oxygen-free flue gas to extract H,S from sour San Andres water, (3) performance of thin-wall cement-lined pipe in water distribution systems including comparison between those sections carrying raw San Andres water and those carrying treated water, and (4) comparison of performance of various lining materials and subsurface equipment in water supply and water injection wells. These experiences are reported without regard to whether results are good, bad or indifferent. Since the operations reported are limited to the techniques, materials, and equipment actually used in the Driver Unit, no comparison is possible with results of other approaches used in other Spraberry floods or in waterfloods generally under different conditions. However, an attempt is made to quantify these experiences as much as possible in the space available to permit other engineers to select those parts applicable to eheir problems. Background The Spraberry, discovered in Feb., 1949, is a 1,000-ft section of sandstones, shales and limestones with two main oil productive members—a 10- to 15-ft sand near the top and a 10- to 15-ft sand near the base, having permeabilities of 1 md or less and porosities of 8 to 15 percent. Extensive interconnected vertical fractures permitted recovery of oil on 160-acre spacing from this fractional-millidarcy sandstone, but they made capillary end effects dominant. Primary recovery by solution gas drive is less than 10 percent of oil in place, with most wells declining to oil production of a few barrels per day when reservoir pressures are still in the range of 400 to 1,000 psi. Partial closing of the fractures with declining reservoir pressure is believed to be the cause of such low production rates at these relatively high reservoir pressures. In 1952 Brownscombe and Dyes proposed that displacement of oil by capillary imbibition of water from the fractures into the matrix rock might significantly increase oil recovery from the Spraberry, overcoming otherwise serious channelling of water through the fractures." A pilot test conducted by the Atlantic Refining Co. during 1952 through 1955 indicated technical feasibility of the process; but low oil production rates averaging I5 to 20 bbl/well/D failed to create significant interest in large-scale waterflooding at that time." Humble Oil & Refining Co. conducted a highly successful 80-acre pilot test during 1955 through 1958 with

Jan 1, 1969

By J. O. Nelson, C. J. Altstetter

Single crystals of hcp cobalt, 3 mm in diameter and up to 35 cm long, were grown using an electron-beam, zone-melting technique. The martensitic-phase transformation was studied in single-crystalline and polycrystalline specimens by making length-change measurements as a function of temperature under various elastic compressive stresses. Upon thermal cycling, single-crystalline or polycrystalline specimens repeatedly transformed almost entirely on the same variant of close-packed plane provided the maximum temperature did not exceed 600°C. Cycling to 1000°C resulted in transformation on more than one {111} variant. This behavior is termed multivariance. The multivariant transformation occurred very rapidly at an M, temperature 2° to 6°C lower than the M, of a transformation which would result in a single-crystal product. Elastic compressive stresses (up to 253 g per sq mm) tended to lower the A, and raise the M, temperatures, decreasing the width of the temperature vs dilatation hysteresis loop. The transformation habit plane and transformation shear direction of an as-grown single crystal were not grossly affected by elastic compressi?ie stress. This was evidenced by similar dilatations on the temperature us dilatation loops joy specimens with and without compressive stress. A dislocation mechanism is proposed to explain the observed results. IT has been shown that, on heating, cobalt transforms martensitically from the hcp to the fcc phase.' The transformation habit plane is (0001)hcp || (lll)fcc and the transformation shear direction is (1010)hcp || (112)fcc. The transformation involves a shear of 1g°28', which may be achieved by a shearing of a/6(112) of every two planes with respect to the plane beneath, thus changing the ABABAB stacking of hcp to the ABCABC stacking of fcc. Associated with the phase change is a 0.3 x 10"3 contraction in the habit plane and a 4.2 X 10"3 expansion perpendicular to the habit plane resulting in a 3.6 x X volume increase on heating.' On cooling, an identical volume decrease takes place. The temperature at which the fcc phase begins to form on heating (A,) is reported as 430°C, and the temperature at which the hcp phase begins to form on cooling from an elevated temperature (A&) is reported as 390oC1,3 Consequently, temperature vs dilatation plots have the form of a hysteresis loop. If heating or cooling is reversed during a transformation, a smaller hysteresis loop results. Upon heating, the transformation is always complete; whereas, fcc is often retained at room temperature as a metastable phase entrapped in the polycrystal-line hexagonal matrix.1,4,5 Two obstacles in the theory of the allotropic-phase transformation of cobalt have been: 1) a detailed knowledge of the product nucleus, and 2) a plausible method of propagation of the transformation. Bilby,8 christian, 7 and seeger 8,9 have suggested a "pole mechanism" as a means of propagation of partiai dislocations from plane to plane. A pole dislocation and a Shockley partial come together at a node. The a/6(112) Shockley partial rotates about the pole dislocation effecting the transformation shear. The pole dislocation must have a 2a/3(111) screw component which causes extension of the transformed region by two atomic planes with each full rotation of the Shockley partial. Bollmannl0 suggested, on the other hand, that transformation propagation occurs due to the stress fields of intersecting (111)-type stacking faults. As faults intersect, a stress distribution is set up about their intersection which is in turn reduced by the emergence of another fault on the second nearest plane. This process continues with the final result of a complete phase transformation. In view of the similarities between deformation and transformation in cobalt, the effect of stress on the transformation would, hopefully, yield valuable information concerning nucleation and propagation. In the present work single-crystalline and polycrystalline specimen length changes were measured as a function of temperature at various compressive loads. PROCEDURE Several orientations of single crystals of hcp cobalt in lengths up to 25 cm were grown by electron-beam floating zone melting from 99.95 and 99.999 pct, 3-mm-diam cobalt rod as supplied by Johnson

Jan 1, 1964

By Burnham E. Field

TAE chemical industry is constantly looking for new materials which either are more resistant to corrosion than those now available or have improved physical properties to meet the requirements of higher temperatures and greater pressures. Attack by acids is-one of the more important forms of corrosion-and in the last few years the development of acid-resistant alloys has been quite rapid. Perhaps the most notable example is that of nitric acid, 'the problem of which has largely been solved by the chromium-iron and chromium-iron-nickel alloys. Sulfuric acid may be handled in lead, iron, or the iron-silicon alloys, depending on conditions. As to hydrochloric acid, no metal or alloy can be called entirely satisfactory for handling. this acid under plant conditions.1 The results of our investigations on the resistance of the nickel-molybdenum alloys to hydrochloric acid have been confirmed by those of Guertler, Rohn, Schulz, Jenge, and others,' but thus far only one such alloy has approached commercial production in Germany; this contains approximately 15 per cent. chromium and 7 per cent. molybdenum with the remainder chiefly nickel. Dr. S. W. Parr, as far back as 1914, developed a complex alloy known as "illium," with a nickel base and containing some molybdenum.3 Dr. Parr was primarily interested in an alloy for lining bomb calorimeters, and while illium does show good resistance to acid it is too expensive for general use. Two United States

Jan 1, 1929

By W. A. Backofen, A. T. English

The kinetics of re crystallization were determined metallographically for a 3-1/4 pcl Si-Fe rapidly compressed at temperatures of 710° to 911°C, and held for various times at the working temperature. As in re crystallization following cold wwk, the time for re crystallization was reduced by increased temperature and strain. Nucleation occurred chiefly at grain edges, although other pre-existing interfaces, notably inclusions, also served as nucleation sites. The importance of intragranular nucleation to grain refinement in hot working is pointed out, together with some possible techniques by which nucleation might be induced within the grains. The observed isothermal growth rates are quite accurately described by the equation G = 4 x 10-'/t (cm per sec), independent of temperature and strain at all but the shortest times. Changes in G during recrystalliza-tion can exceed two orders of magnitude. It is argued that release of stored energy associated with lattice defects cannot adequately explain the time dependence. A suggested alternative involves processes of solute segregation and desegregation in the unrecrystallized matrix and at the moving boundary, respectively. EFFORTS to improve hot-working practice are hampered by an incomplete understanding of the fundamental metallurgy involved. Research directed at establishing the required basic foundation falls into two categories, the first concerned with measurement of mechanical properties under the conditions of high temperature and strain rate which characterize such processing, the second focused on structure and its relation to the deformation conditions. Rossard,' Rossard and Blain,2 and Hardwick and Tegart have conducted many high-speed, high-temperature torsion tests on various metals. One of their objectives was interpretation of stress-strain curves in terms of the structures of specimens rapidly quenched following interruption of twisting. They showed that appreciable hardening occurred in the early part of the test, and that this hardening reflected the concurrent development of an increasingly dense substructure within the grains. The detailed nature of this substructure was observed to depend on the ease of polygonization which, at least in fcc metals, varies with the stacking-fault energy.= By holding specimens after interruption but before quenching, the nucleation and growth of new grains could also be studied. Some success has been realized in relating the microstructure of hot-rolled steel to its temperature:strain rate:strain history with such testing.' The same general observations have been made by others investigating rolling4f5 and drop-hammer forging.~-~ Incident to these experiments, some efforts were made to determine the kinetics of re-crystallization as well as the velocity of the migrating boundaries. The results have been largely qualitative, owing to difficulties of interpreting hardness measurements5 and microstructures. The work described here was undertaken to obtain more quantitative information from tests on a material having suitable metallographic properties, and, in this way, to provide further insight into the fundamentals of this practically most important kind of deformation processing. I) MATERIALS AND EXPERIMENTAL TECHNIQUES Materials. Electrolytic etching of a Si-Fe alloy reveals dislocations and substructure in unrecrystallized grains.8'9 This unique characteristic makes possible a precise determination of the extent of recrystallization. For that reason, it was the material selected for all experiments in the present work. The two particular alloys that were used are identified in Table I. A major difference between "A" and "B" is the number of inclusions, as noted in the table. Most of the experiments were made with material "A". It was received as hot-rolled plate 1 in. thick, sawed to 2-in. widths, hot-forged at 1200°C to 5/8-in. rounds, and finally annealed in a mechanical vacuum at 1000°C for 24 hr. The result was substructure-free grains of mean diameter 0.05 cm.*

Jan 1, 1964

By Harry V. Welch

This paper presents a brief discussion of numerous devices and processes which have been utilized for the recovery of values from gases in copper reduction works and describes in greater detail the development and application in recent years of electrical precipitation, more familiarly known as the Cottrell process, to the problems of dust losses with furnace gases in copper-smelting and refining plants. The field for collection of suspended particles in gases is widely extended in our modern complex, congested .and industrialized mode of living, and its satisfactory solution is required by our increasing appreciation of the extravagant waste, unhealthful effects and nuisance which such uncontrolled emission of solid suspensions represents. Much of the special dust-recovery equipment in use today has been developed in one industry and carried over to many others. The early work of Cottrell was with sulfuric acid mists, aimed at the purification problem in contact acid manufacture, but the present uses of Cottrell equipment cover a diversified field—carbon black, combustible gas, oil mists, iron blastfurnace fumes and dusts, cement-kiln gases, as well as the purification of gases in contact and chamber acid plants and its wide and extended use in the nonferrous metallurgical field of copper, zinc and lead, and their associated metals. Dust and fume collection from furnace gases became a problem only with the modern development of large and amply powered auxiliary furnace equipment, which in turn permitted large furnace units, fast driving and large outputs of finished product per unit of furnace capacity. The ancient metallurgist with his small clay pot and hand-operated bellows had too little gas velocity to cause a real dust loss. As furnaces grew in size, flues and stacks were added, and undoubtedly the first observable dust losses were indicated by the deposits in the flue and stack base. Large flues, it was noted, collected more than smaller ones, and the expansion of a portion of the flue into a chamber represented the first serious attempt at recovery of furnace dust losses. For a century or more the settling chamber represented the best of skilled metallurgical practice in recovery of furnace dust, and it may be said to have reached

Jan 1, 1934

By Zay Jeffries

Tungsten has the highest melting point of all the known metals, namely 3350 C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely brittle and fragile at room temperature, and when possessing a fibrous structure it may be ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given. Manufacture of Wrought and Ductile Tungsten Up to about 10 years ago, it had not been possible to work tungsten mechanically. About the year 1908, Dr. William D. Coolidge, of the General Electrie Go., produced ductile tungsten from what was then supposed to be an inherently brittle metal and which, in fact, was inherently brittle in its normal state, that is, when composed of equiaxed grains. Since that time many products, chief among which are the filaments for electric incandescent lamps, have been made from wrought and ductile tungsten. Tungsten is produced chiefly from the minerals wolframite and scheelite.1-8 The ores may be reduced in many ways. For example, the ore may be fused with alkali carbonates and the fusion dissolved in water; sodium tungstate is formed, which is soluble in water. This

Jan 1, 1919

By J. J. Gilman

Zinc monocrystals, when compressed nearly parallel to their basal planes (within 20), deform in a new way; and certain deformation markings, called "-bands," are typical of this new mode. Characteristics of these bands are described. Mechanical behavior of low angle zinc monocrystals was investigated in some detail. Recrystallization did not occur upon annealing of banded specimens that were free of deformation twins. -Bands do not seem to be the result of nonbasal slip, but rather, a result of a microbuckling mechanism. u-Bands differ qualitatively and quantitatively from ortho kink bands. A dislocation model, consistent with some of the features of u-bands, is described. THE plastic deformation of zinc monocrystals with slip planes (0001) nearly parallel to the stress axis was studied in this investigation. In a previous investigation, it was shown that some low angle zinc crystals (those with slip planes making angles of more than about 2.5+1° with the compression axis), deform by ortho kinking while others (those with slip planes making angles of less than 2.5+1° with the compression axis) deform in a new way.' This new mode of deformation will be described in some detail here. Some of its striking features are: 1—it operates only for compressive stresses, 2—its temperature dependence is anomalous, and 3—it exhibits a new type of "yield-point" behavior. The mode of deformation to be discussed is not new in the sense that no previous evidence of its existence had been reported. The markings that it creates on the cleavage surfaces of zinc crystals have been described by several investigators.'" However, this is the first time that it has been made to operate under controlled conditions so that its response to mechanical variables, temperature, and aging treatments could be investigated and its geometry completely described. Apparently. Jillson' as well as Holden3 and Pratt" believed that the small bands they observed were simply small versions of ortho kink bands. In fact, two of these authors3,6 "alled the markings "micro kink bands." In spite of the precedence, it is felt that this term is not entirely suitable because these bands do not have the same genesis as kink bands, and they are qualitatively different in structure. As will be indicated by later discussion, the bands seem to be related to the tensile deformation bands observed in aluminum. The present author has chosen to call the bands "micro deformation bands," or simply ",ubands," and the deformation process, ''p-banding." Experimental Methods Crystals were grown from 99.999+ pct Zn obtained from the New Jersey Zinc Co. The details of the technique are given elsewhere." It should suffice to say that the crystals were seeded for orientation control, and precision pyrex tubes were used for molding them. About 40 crystals were used, yielding some 130 specimens. Fig. 1 illustrates the typical form of the specimens and shows how the orientation angles are defined. The crystal specimens were usually 1 3/4 in. long and about 150 mil in diameter. The angle between the slip or cleavage plane (0001) and the specimen axis is designated by xo, while a is the angle between the maximum slope of the (0001) plane and the nearest close-packed direction [1210], vary ing from 0°to 30°. The crystals were cut into specimens with a jeweler's saw and the ends were squared by filing (specimens held in V-block). Crystals of this orientation are stiff toward bending, so this procedure introduced only deformation localized at the ends. Then the specimens were polished either chemically in 50 pct HNO³ or electrolytically in 20 pct chromic acid. The mechanical tests were made with an Instron testing machine. This machine weighs by means of electric strain gages on elastic bars and is quite stiff, since the full-load deflection of its load cells is at most 0.002 in. Most of the testing was done at a

Jan 1, 1956

By C. R. Knopp

Gas-oil relative permeability ratio is an important relationship in oil reservoir predictive calculations. A correlation has been developed from 107 gas-flood k/k tests on Venezuelan core samples. The correlating parameter is based on restored-state water saturation tests and' is applicable to both consolidated and poorly consolidated sandstone reservoirs. Data of the correlation show that there are no distinguishah1e differences between the mass-data groupings for the two c1assifications A procedure is recommended for running .sufficient relative. permeability analyses to compute a geometric mean of the sample group. The geometric mean is more representative of the total core, and probably the entire reservoir. For example, while only one in four of the k,,/k,., test curves agreed closely with the resultant correlation of this report, the geometric mean curves of the 16 suites (three samples or more). showed good agreetment ill three cases out of four. INTRODUCTION The gas-oil relative permeability ratio is an important, fundamental relationship in most oil reservoir predictive calculations. Predictive calculations are made to estimate future reservoir production characteristics and ultimate oil recovery. The k1,/k2, relationship is specifically needed to relate the surface gas-oil ratio to the reservoir oil and gas saturation, and to calculate the relative movement of these phases within the reservoir whenever some of the more complex driving mechanisms are present. Laboratory k1/k2, tests are not generally run as a routine analysis. Consequently, k1/k2 data often are not available when needed because the cost of laboratory work could not be justified or the need for such data had not been properly anticipated. When laboratory k1/k2, data are available, they are often very difficult to interpret. For example, wide divergence is sometimes shown in a family of k1,/k1, tests representative of the producing horizon in a single well. With these considerations in mind, a study was made to determine if a relationship might exist between the k1,/k2, curve and some other simple laboratory test criteria. The most probable k1/k2, curve correlation for Venezuela described in this paper is the result of the investigation. The presented correlation defines the most probable gas-flood k,,/k,, curve through the medium of air-water capillary displacement and centrifuge water saturation tests. The laboratory procedures of these tests are. relatively simple, and inexpensive; test data should be. widely available- from routine analysis. DATA AVAILABLE, LABORATORY METHODS The report correlation utilized 107 gas-Hood k1/k2, tests run on sandstone cores of Venezuelan reservoirs. Table 1 is a general tabulation of data pertinent to the tests, while Table 2 summarizes the data. Thetests include 96 from Western Venezuela and 11 from Eastern Venezuela. Eighty-two- of the 107 test samples were sandstones that varied from poorly consolidated to-unconsolidated; 25 were consolidated. The average sample porosity was 26.7 per cent and the average permeability was 1,121 md; these values typify the better sandstone reservoirs of' Venezuela. The Welge gas-flood technique,' based on fundamental Buckley-Leverett frontal displacement theory, was introduced in about 1952 and is widely accepted in the industry. The laboratory procedure is relatively simple, rapid, and can be performed on small core samples. While there have been some minor variations in sample preparation and laboratory procedure in the tests used for the correlation, these tests can be generally summarized as follows. The core sample was first sol vent-extracted and dried. Connate-water saturation was restored by the oil-flushing or evaporation-blow down methods. At the beginning of gas flood the hydrocarbon pore volume was completeiy saturated with the test oil phase. Unsteady-state gas-oil displacement then began with the injection of nitrogen or helium. while the displaced oil and gas phases were incrementally metered at the out-flow face. From the test data, the k,,/k,, curve was calculated by the Welge method.' The individual oil and gas relative permeabilities were also calculated." CORRELATING PROCEDURES In attempting to establish a basis of correlation, we found that broad mid-range sections of 105 of the 107 k,,/k,, test curves could be closely duplicated by a straight line. Only two curves did not show a degree of linearity in this region. Correlation-curve definition parameters were subsequently developed from this observation of consistent mid-range linearity. Possible correlating variables were limited to the physical properties measured on core samples that (1) were widely available as common test data and (2) could be easily and cheaply obtained through future laboratory work. The more obvious possibilities were porosity, permeability and

Jan 1, 1966

By W. V. Swarzenski

In its effort to combat waterlogging and soil salinity, the Water and Soils Investigation Division of WAPDA (West Pakistan's Water and Power Development Authority) has carried out an extensive program of test drilling andwater sampling since 1954. Data collected during the past ten years have permitted the delineation of fresh and saline groundwater zones in the Punjab Plain. Fresh groundwater containing generally less than 500 ppm of total dissolved solids is found in wide belts paralleling the major rivers and in other areas of fresh-water recharge. Locally, fresh groundwater extends to depths of 1500 ft and more. Saline groundwater occurs down gradient from sources of recharge, particularly in the lower central parts of the interfluvial areas, and presumably underlies most of the Punjab Plain. The groundwaters of the Punjab are characterized by their evolution from calcium, magnesium bicarbonate waters near sources of recharge to waters containing a dominant proportion of sodium. The highly mineralized waters of the Punjab are generally of the sodium chloride type, whereas in the Dera Ismail Khan District, sodium sulfate waters predominate. The pattern of distribution of saline groundwater zones and the observed gradual increase in mineral content, down gradient from sources of recharge, can be explained best by a hypothesis stressing the process of evaporation from the water table and solution of minerals within the alluvial aquifer. In 1954, detailed groundwater surveys in the Punjab Plain were initiated by WASID, the Water and Soils Investigation Division of West Pakistan's Water and Power Development Authority. The investigations, undertaken under a cooperative agreement between the governments of Pakistan and the United States, were aimed at the formulation of reclamation measures to improve waterlogged and saline soils, and to assess the groundwater potential of the Punjab and other areas of West Pakistan. The nature and urgency of WASID's primary task limited the exploration of the alluvial aquifer generally to its uppermost part. About 1030 test holes drilled in 47,000 sq miles of the Punjab defined the nature of the alluvium to depths of about 600 ft and yielded data on water quality to 400 or 500 ft. A report on the hydrology of the Punjab, based on the results of these investigations was published by WASID in 1963.' The present report incorporates data obtained by WASID since 1962 in a program of deep test drilling in the Punjab and the adjacent areas of Bahawalpur and Dera Ismail Khan District, permitting the definition of fresh and saline groundwater zones to depths of 1500 ft in some areas. Groundwater in the Punjab Plain is contained in alluvial deposits, predominantly sand and silt, which extend almost everywhere to depths of 1000 ft and more. The alluvium has been deposited by the Indus River and its tributaries since late Tertiary time and is contiguous with similar deposits in India. The Indo-Gangetic Plain extends from the foothills of the Himalayas to the ancient rocks of the Peninsular Shield in central India and to the ocean. Gradients are generally very low and range from about 1% ft per mile in the upper part of the plain to less than 1 ft per mile in the south and southwest. The monotony of the alluvial plain is broken by scattered bedrock outcrops in two of the interfluvial areas, Chaj Doab and Rechna Doab. The bedrock hills are projections of the northwest-trending Delhi-Shahpur Ridge that is largely buried by alluvium. The rocks of the buried ridge, presumably of Precambrian age, are essentially impermeable and define the lower limit of the alluvial aquifer in parts of Chaj, Rechna, and Bari doabs. Elsewhere in the Punjab, there are no outcrops of other consolidated rocks and their presence below the alluvium is conjectural. The principal areas of bedrock outcrops, near Kirana and Sangla, are shown diagrammatically in Fig. 1. The movement of groundwater through the alluvial aquifer of the Punjab has been described by Green-man and others.' In most of the area, the pre-irriga-tion water table sloped from the rivers downstream and toward the central axes of the doabs, indicating that the rivers were sources of groundwater recharge. As a result of seepage from irrigation canals, water levels have risen as much as 90 ft. In 1960 they were within 5 to 15 ft of the land surface and above the

Jan 1, 1970

By P. H. Dudley

The piping and segregation of ingots of steel is a comprehensive subject, and must be studied in reference to the different grades of soft, medium, and hard steel, rather than to discuss it in a general manner, as though applicable to all grades. Rail steel, however, will receive the most consideration in this paper, for the wheel-loads of the motive power and rolling stock have doubled from 1890 to 1910. Steel rails and tires which were efficient under the light loads, became less serviceable under the double wheel-loads, quadrupled tonnage, and higher speeds. Bessemer Steel. Bessemer steel of from 0.10 to 0.15 per cent. of carbon, for splice-bars, spikes, and tie-plates, rises in setting, and is cast in bottle-mouthed molds, which must be capped to prevent an overflow from the top. This grade of steel rises in the molds and makes a longer ingot than the volume of molten steel when first teemed. The ingots which are allowed to cool and then cut open, show, particularly in the upper part, large occluded blow-holes, and when they are not oxidized or do not contain foreign matter, weld more or less completely when the steel is rolled or forged above 1,100° C., and it is in this way that the blow-holes are closed in the low-carbon steels. Boiler-Plate and Fire-Box Steel. These grades often contain more or less minute laminations, which are the remains of small blow-holes forming after the setting metal has reached a pasty condition. The blow-holes in the low-carbon steels have not been prevented by usiug deox-idizers, though the ingots are slightly improved so far as the soundness of the steel is concerned. This grade of steel also rises in the molds in setting.

Jan 1, 1914

By F. H. Vitovec, D. W. Hoeppner

Pusk-pull fatigue tests were conducted on copper tricrystals of 99.988 pct purity to ascertain the role of grain boundaries in the initiation and propagation of fatigue cracks. Significant differences in behavior were found for specimens which possessed different transverse-boundary misorientation. In speciwens with low boundary angles cracks initiated within the transverse boundary, while higher angles led to transcrystalline fatigue failure. It is suggested that at low angular misorientation moving dislocations may interact with dislocations of the boundary or dislocations present in adjacent pains on favorably oriented glide planes, thus initiating a fatigue crack. MANY fatigue studies have been concerned with fatigue-crack initiation within grains and the mechanism causing initiation and propagation1-3 Although the initiation of fatigue cracks in or near grain boundaries of pure metals has been observed and reported in the literature, the mechanism of this phenomenon has received little attention.4"11 EXPERIMENTAL PROGRAM Testing Procedure. To investigate the role of grain boundaries regarding initiation and propagation of fatigue cracks, copper tricrystals were tested in push-pull. Axial-stress tests were used to avoid the stress gradients introduced by stressing of some other nature. Copper was selected as the most suitable test material since extensive work has been done on the formation of fatigue-induced slip in copper. Tricrystal specimens were used to provide a grain boundary geometry with one boundary transverse to the principal stress axis and one or more boundaries nearly coincident with the direction of maximum resolved shear stress. The boundary energy and the slip characteristics in the vicinity of the transverse boundary depend on the relative orientations of grains across the boundary. Testing was done at room temperature, at a frequency of 700 cpm, in an atmosphere of either air or argon. It is known that the incidence of grain boundary cracking increases with increasing temperature and decreasing frequency.4 The fatigue machine applied a uniaxial tension-compression load to the specimen by a flat spring which was actuated by an adjustable eccentric. Use was made of an adjustable head and a load cell which had strain gages mounted at 120-deg intervals around its periphery, thus providing a means for eliminating any detectable superimposed bending moment. A clip gage was mounted between the gripping heads to record the cyclic strain amplitude applied to the specimen. Each specimen's hysteresis characteristics were recorded by supplying the load and strain signals to an oscilloscope. Microstructural changes were observed and recorded with an optical microscope which was mounted on the fatigue machine. Immediately prior to insertion in the machine, each specimen was chemically polished. Extreme care was exercised while inserting the specimen in the test machine to avoid either bending the specimen or introducing a mean load. Each specimen was stressed in the tensile direction first and subsequently the load was reversed. Specimen Preparation. Tricrystal fatigue specimens of 99.988 pct Cu were grown from the melt using a modified Bridgman technique. Ingots about 1 in. high were grown to the configuration shown in Fig. 1. Upon sectioning the resultant ingot, several specimens were provided with an identical shape and grain boundary orientation. Except for plane sectioning and final polishing, this method eliminated machining the specimens. The apparatus used for growing the tricrystals is shown in Fig. 2. A spectrographically pure graphite mold, Fig. 3, was inserted in a vycor tube which was mounted on a vertical zone-refining table. Prior to insertion in the tube the mold was assembled as follows. The insert and graphite rods were fixed in position in the mold. The copper was then placed in the mold and the entire mold assembly was positioned in the vycor tube, Fig. 2. At this point the tube was sealed, evacuated, purged with helium gas, and finally placed under a slightly positive helium pressure. The heating coil was then adjusted to melt the copper charge, after which it was raised at a speed of 4 in. per hr. It is also possible to use

Jan 1, 1964

By W. C. Winegard, J. R. Carruthers, A. Plumtree, L. R. Morris

The unidirectional solidification of dendrites containing central twin planes was studied in A1-Ti alloys. Once nucleated, the twinned dendrites are a Twore ejficient form for solute redistribution and therefore grow in preference to the normal columnar dendvites. Comparison of these twinned dendrites to adjacent colunmar dendrites by means of decanting experinzents and electron-probe rnicvoarmlysis indicates that these special dendrites grow with less undercooling than normal dendrites. These findings are further supported by the effect of forced convection on the dendrite morphologies. COMMERCIAL semicontinuous cast ingots of most aluminum alloys frequently exhibit large grains which appear to be composed of hundreds of parallel, continuous, thin lamellae. This structure has been termed "basaltic",' "fiederkristall", or, commonly, "feathery grain". The lamellae are 'about 100 p thick, several inches long, and each lamella contains a central (111) coherent twin boundary. The feathery grain has been reported to have a (112) direction2 and a (110) direction4 in the twin plane parallel to the casting direction, in contrast with the usual columnar structure where a (100) direction predominates. Aust et uZ.~ proposed that the twin boundaries were growth twins nucleated by stacking faults on the octahedral planes. chalmers6 has suggested that feathery grain may grow by a re-entrant edge mechanism, as proposed by wagner7 for twinned dendritic growth in germanium. Cahn et ~1.~ have concluded that the occurrence of feathery grain is evidence of some form of lateral layer growth rather than the atomically continuous growth normally observed in metals. The postulates by Chalmers and Cahn would seem to be contradicted by the work of Nakao~"' who showed that feathery grain only occurs when growth rates are high and the aluminum contains some solute. Specifically, Nakao found that in order to obtain feathery grain, in small castings solidified unidirec-tionally upward, the rate of growth must be above 2.4 cm per min and a critical solute concentration must be present. Below this solute concentration the grain structure was totally columnar. The critical solute concentration was found to be approximately: 0.04 wt pct Ti, 2 wt pct Cu or Mg, and 8 wt pct Zn. As pointed out by Chalmers it is not obvious why a twin-plane re-entrant edge mechanism would occur in aluminum which is thought to have a diffuse solid-liquid interface. The present experiments were undertaken to determine the growth mechanisms in- volved and to study the solute segregation in more detail. EXPERIMENTAL PROCEDURES Alloys ranging in composition from 0.05 to 0.23 wt pct Ti* were prepared from 99.9 pct pure Ti and 99.993 pct pure Al. Two-hundred-gram samples of A1-Ti binary alloys were solidified unidirectionally and vertically upward from a water-cooled copper base, in a heated insulated mold. The 1-in.-diam, 6-in.-length mold was made of Marinite (manufactured by Johns-Manville Co.). The mold was attached to a 24-in. pivoted arm such that by dropping a weight the mold was rotated 180 deg, throwing the liquid metal from the solid. In this way, the solid-liquid interface was revealed by decanting. A sketch of the decanting mold is shown in Fig. 1. The alloy was poured into the mold at temperatures ranging from 680" to 750°C, partially solidified by water cooling from the base, and decanted after a measured time interval. Growth rates for each metal-pouring temperature were calculated from solidification-time vs length solidified curves. Temperature gradients in the melt were measured using four No. 34 gage thermocouples which protruded into the mold cavity. Grain orientations were determined by X-ray diffraction using Laue back-reflection techniques. Grain substructures were examined metallographically, using polarized light, by applying a thin epitaxial anodic film to polished sections after the method of Hone and pearson." Titanium micro segregation was measured by electron-probe microanalysis using a NORELCO AMR/~ with a mica crystal and proportional-flow counter. Several of the cast samples exhibited feathery and columnar dendrites growing in the same direction and

Jan 1, 1967

By Arthur C. Forsyth, R. L. Dowdell

A search through the available literature shows that the cobalt-nickel-silicon system has not been systematically studied. This seems rather odd because all three elements are fairly abundant and have better than average corrosion resistance; however, they have high melting points, which makes experimental work difficult. Cobalt and nickel form a continuous series of solid solutions and each metal dissolves about 7.5 per cent silicon. Many ternary alloys have been studied and the results have been published in a great many different ways, but to present such data in a short but clear and understandable manner is still a problem. The following pages describe the results of the study of 76 alloys from which the partial ternary diagram (Fig. 1) of the cobalt-nickel-silicon system has been drawn. The alloys were chosen according to the plan in Fig. la by taking definite ratios of cobalt and nickel, such as 70 Ni, 30 Co or 40 Ni, 60 Co, and adding silicon in various percentages. Each section was studied in detail by means of thermal analysis and microscopic examination, but only two of these detailed sections were thought necessary in the point perspective drawing to give a comprehensive picture of the liquidus, solidus and solid transformations that take place over the temperature ranges studied. Complete thermal analyses and microscopic data are given in Table 1. Experimental Procedure The alloys were prepared from metals of commercial purity, as follows: electrolytic nickel 99.60 + 0.35 Co; chemically purified silicon 99.79 per cent plus impurities of Fe 0.027, A1 0.008, Ca 0.014, C 0.004, N² 0.10; and cobalt 98.82 per cent plus impurities of Ni 0.42, Fe 0.12, CaO 0.27, S 0.012, Mn 0.10 and SiO² 0.15. It should be noted that the largest impurity in cobalt is nickel, one of the alloying elements. The alloys were melted in a small Ajax induction furnace, the nickel and cobalt being melted first because of their better ferromagnetic

Jan 1, 1940

By Arthur C. Forsyth, R. L. Dowdell

A search through the available literature shows that the cobalt-nickel-silicon system has not been systematically studied. This seems rather odd because all three elements are fairly abundant and have better than average corrosion resistance; however, they have high melting points, which makes experimental work difficult. Cobalt and nickel form a continuous series of solid solutions and each metal dissolves about 7.5 per cent silicon. Many ternary alloys have been studied and the results have been published in a great many different ways, but to present such data in a short but clear and understandable manner is still a problem. The following pages describe the results of the study of 76 alloys from which the partial ternary diagram (Fig. 1) of the cobalt-nickel-silicon system has been drawn. The alloys were chosen according to the plan in Fig. la by taking definite ratios of cobalt and nickel, such as 70 Ni, 30 Co or 40 Ni, 60 Co, and adding silicon in various percentages. Each section was studied in detail by means of thermal analysis and microscopic examination, but only two of these detailed sections were thought necessary in the point perspective drawing to give a comprehensive picture of the liquidus, solidus and solid transformations that take place over the temperature ranges studied. Complete thermal analyses and microscopic data are given in Table 1. Experimental Procedure The alloys were prepared from metals of commercial purity, as follows: electrolytic nickel 99.60 + 0.35 Co; chemically purified silicon 99.79 per cent plus impurities of Fe 0.027, A1 0.008, Ca 0.014, C 0.004, N² 0.10; and cobalt 98.82 per cent plus impurities of Ni 0.42, Fe 0.12, CaO 0.27, S 0.012, Mn 0.10 and SiO² 0.15. It should be noted that the largest impurity in cobalt is nickel, one of the alloying elements. The alloys were melted in a small Ajax induction furnace, the nickel and cobalt being melted first because of their better ferromagnetic

Jan 1, 1940

By F. L. Wolf

The catenary system of line construction possesses so many desirable characteristics from the operating standpoint that it has wide application for all types of electric traction. Many steam roads are electrifying sections of their lines, and in most cases are operating both steam and electric locomotives over the same track. This means that the overhead catenary system is subjected to the severe corrosive action of locomotive smoke, and data concerning the resistance of various alloys to this form of corrosion are very desirable from every point of view. Reliable and specific information and data on the subject of corrosion due to steam and smoke from locomotives are extremely meager and, on this account, extensive service tests, together with accelerated tests, have been made on a number of commercial metals and alloys. The observations and data recorded in this paper are the result of a preliminary test which was started in 1923 and which has been carried on to the present time. The recognition of the need for even more detailed and accurate data has resulted in the undertaking of another test which has been in progress for about a year. The result of this test will be published in due course. Some years ago The Ohio Brass Co. was asked by one of the large steam railroad companies to furnish data on construction details for a catenary system which it was considering for one of its divisions. The selection of materials which would give the necessary physical characteristics as well as withstand the severe corrosive action of locomotive gases caused electrical railroad engineers considerable concern. At that time, there were available no specific or authentic data on these important questions: no systematic investigation of the problem appeared to have been made, even though it's importance was generally recognized. Such observations as had been made were crude in that they had been limited largely to visual inspection which too frequently is most misleading. However, the scattered information which was collected gave important clues as to how best to start an investigation. Technical literature was studied, metallurgical experts were consulted, and the problem was discussed with engineers who were in close contact

Jan 1, 1930

By A. U. Seybolt, R. A. Oriani

The pressure and composition of the solid solution of nitrogen in chromium has been investigated as a function of temperature. The partial molal heat of solution, the activity of nitrogen in solid solution, and the partial molal free energy have been computed. The enthalpy of three reactions is summarized: N + 2Cr(3) = Cr2N(4), H° = —28,500 cal per mol 1/2N2(p) + 2Cr(8) = Cr2N(3)1 ?HO = —23,500 cal per mol 1/2N2(p) = N, ?H° = 5,000 cal per mol. WORKERS who have investigated the problem of the preparation of ductile chromium have been concerned with the effects of minor amounts of impurities upon this refractory metal. In particular, gaseous impurities such as oxygen and nitrogen have been suspected of causing trouble because of many known cases where brittleness in transition elements has been definitely traced to these elements. In order to evaluate the possible effects of the nitrogen impurity in chromium, it appeared desirable to learn something of the dependence of the nitrogen solubility upon temperature and pressure. Previous Work Maier3 in 1942 in his treatise on sponge chromium reviewed the thermodynamics of the chromium nitrides Cr2N and CrN, both of which are well-estab- lished compounds, but which apparently have not been studied in much detail. Maier presented some free energy-temperature expressions for the reactions 2 Cr,N = 4 Cr + N2 [1] and 4 CrN = 2Cr2N + N2 PI based mainly on the work of Satoh2 and Sano." Pearson and Ende3 in 1953 briefly reviewed the thermodynamics of Cr-N using the same data available to Maier, and also derived a free energy-temperature expression for reaction 1. Of the two nitrides mentioned previously, the present investigation was only concerned with Cr,N, since this nitride is in equilibrium with the metal phase, at least over most of the temperature range, Blix4 in 1929 established the structure of Cr2N (close-packed-hexagonal) by X-ray diffraction methods, and indicated that its homogeneity limits extend from 11.2 pet to 15.1 wt pet N. At a temperature of 1200°C, 38 mm Hg from the Maier expression and 43 mm Hg from the Pearson

Jan 1, 1957