Search Documents

By Arturo M. Morales

INTRODUCTION Manganese carbonates are nodulized by Cia. Mineral Autlan, located in Ongongo in the state of Hidalgo in Mexico. This kiln is fed minus 15 mm material at the rate of 1870 tpd. About 920 tpd is nodulized into a commercial product having a size range of 15 mm to 12 mm. The kiln also produces about 320 tpd of minus 12 mm fines and 40 tpd of chimney dust. Currently, the minus 12 mm fines are being recirculated to the kiln and the chimney dust is not being utilized. It has been found that there exists a market for manganese to be used as feed to the ferromanganese and silicomanganese furnaces. However, a coarse, lumpy feed can only be used in these furnaces. Accordingly, it has been proposed to screen the fines at 6 mm and agglomerate the minus 6 mm fraction along with the chimney dust and suitable binders. This paper presents the results of a feasibility study and test work aimed at producing an acceptable agglomerated product from the kiln fines for use in the ferromanganese and silicomanganese furnaces. Since the agglomerated product will have to be handled and loaded into trucks in the kiln area and transported over long distances, a minimum strength of 200 N is expected to be necessary. They should also have enough initial strength to be stockpiled and result in a minimum of breakage. A third important requirement is that the agglomerates should be resistant to disintegration during combustion. The recirculating fines were to be agglomerated in their original state, if possible, that is, without grinding. This eliminated the possibility of pelletizing as an agglomeration method. Based on a few laboratory trials, the briquetting method seemed most attractive, and a test program was initiated to explore the briquetting process.

Jan 1, 1977

By F. L. Ruhlman, Max C. Eastman

The termination of the recent war marked a major changc in the oil-field operations at. Elk Hills. Production was greatly curtailed, various experimental production projects were started, and a long-range exploratory program was inaugurated. Production was reduced from the wartime peak of 65,000 bbl per day to the current rate of about 8ooo bbl per day in order to maintain an available source of crude that can be drawn upon during a national emergency. The existing production rate is deemed essential to carry on the experimental production projects. These projects are being conducted to determine the best methods and means of maintaining the Reserve, shut in, but in a state of readiness to produce the maximum quantity of oil in the most expeditious manner. Projects now being investigated include: (I) protection of surface equipmerit; (2) repair of wells that might damage the reservoir; (3) gas injection; (4) water eneroachment, (5) gravity drainage. An exploratory program is being carried on to determine the amount of recoverable oil in the unexplored portions of the Reserve. The Shallow-zone exploration is practically completed, but owing to the complexity of the Stevens structure and the magnitude of the oil discoveries in the Stevens, exploration will probably continue in that zone for another two years. Introduction Summary of Development History of Elk Hills Although a detailed history of Elk Hills oil field is presented in various publications,1,2 a summary of its unusual development and production history will be given in order that the present problems may be more readily understood. The first development that resulted in commercial production was in the central part of the Reserve. The first well, Hay No. I, in sec 36-R,* was completed in January I9I9, and was soon followed by 37 Others in the same general area. It is commonly referred to as the Hay-Carman area and was shut in in stages from 1925 to 1934 as a result of litigation regarding the title to the land. Not being highly producti,, only about 6½ million barrels of oil with a large volume of gas was produced from the area prior to the shutdown. Shortly after the start of the development of the Hay-Carman area, drilling was started 6 miles east in sec 36-S' Tupman NO. I came in for 5000 bbl per day early in I92o, It was followed by more than 200 others in the next few years, and the field became one of major importance. Produc-

Jan 1, 1949

By M. E. Wadsworth, T. L. MacKay

Sintered UO, samples were leached in sulfuric acid solutions of various concentrations. A pressurized system was used so that it was possible to investigate the kinetics of the reaction to 270°C with oxygen overpressures as high as 900 psi. The rate was observed to be a function of the concentration of hydrogen ions and directly proportional to the partial pressure of oxygen. Evidences are presented which indicate that a UO2 surface site reacts with a molecule of water to form a hydroxyl complex which in turn can dissociate with the characteristics of a weak acid. A rate determining step has been proposed which involves the reaction between an oxygen molecule and the hydroxyl complex on the surface of UO,. ThE 2 principal methods for uranium dissolution are carbonate and acid leaching. The sulfuric acid leach is the more popular and is used for the treatment of the majority of the ores of Africa, Canada, and the United States. Low recoveries in basic leach circuits led investigators at the University of British columbia1 to study leaching of uranium ores in pressurized vessels. Early in the study of dissolution of uranium it was found that only uranium in the hexava-lent state could be leached in acid or basic circuits. Therefore, the use of oxygen over-pressure in an autoclave offered an interesting approach to solving the low recovery problems of carbonate leaching. UO, was used in this study because it could be obtained in high purity and also because it is representative of the most refractory of the primary uranium minerals. A pressurized system was used to provide a means whereby important temperature and pressure parameters could be varied for the evaluation of the kinetic processes. The mechanism for the dissolution of UO2 should be similar for any of the uraninite type minerals. At the present all of the kinetic studies that have been conducted have been in carbonate media. Peters and Halpern2 carried out a kinetic study of the leaching of pitchblende. Their specimens were pitchblende ores selected on the basis of high grade and homogeneity. Pearson and wadsworth3 conducted a kinetic study of the dissolution of UO2 in carbonate solutions with results very similar to those obtained by Peters and Halpern. EXPERIMENTAL The UO2 as received* was found by spectroscopic *Mallinckrodt reagent, supplied by the Atomic Energy Commission. analysis to have a purity of 99.94 pct 0.03. It was ground in a mechanical agate mortar and screened through a 400-mesh sieve. Thin flat disks of UO2 were prepared by pressing the sized powder in a specially constructed die at a total pressure of approximately 25 tons per sq in. The pressed disks were approximately 0.25 cm thick, 1.6 cm diam, and 3.5 g in weight. As pressed, the samples were approximately 65 pct of theoretical density. It was essential that a binder such as poly-vinyl alcohol be added before pressing to prevent formation of cracks when fired. It was found by trial and error that pressed disks sintered close to 1870°C in a hydrogen atmosphere, reach densities between 91 and 91.5 pct of the theoretical density. At this density the samples had no measurable porosity based upon a 2-hr emersion in boiling water. An X-ray examination of these sintered UO2 disks showed them to be identical with the original UO2 received. Reaction of UO2 with the alundum furnace core was prevented by placing molybdenum between the samples and the core according to the method of Corwin and Eyerly.4 Leaching studies were carried out in a specially designed autoclave, the details of which have been presented e1sewhere.6 The main features of the equipment as applied to a kinetic study are: 1) solution samples may be removed during the course of a single run; and 2) temperature and agitation are carefully controlled. Two-ml samples removed from the autoclave during the course of a run were analyzed for U3O8 content with a Beckman model DK-2 spectrophotometer by the method of

Jan 1, 1959

By A. E. Powers

YEARS of experience and research have shown that molybdenum, tungsten, and vanadium are among the most useful and effective elements in augmenting the high-temperature strength of heat-treatable, ferritic steels. Grün, for example, in conducting an early survey of the strengthening effects of various elements in annealed, low-carbon steel at 750° and 930°F (400° and 500°C), found molybdenum and vanadium to be the most effective.' Holtmann comprehensively studied the strengthening effects of molybdenum and vanadium in quenched and tempered steels at 930°F as a function of microstructure and carbon content.' He found creep strength to be related to the saturation of the austenite at the austenitizing temperature, such that strength is increased by alloying until the y loop is reached—the terminus of complete austenitization. Beyond this degree of alloying, the inability to heat treat will result in lower strength, at least for low and moderate creep temperatures. Tungsten, owing to higher cost than molybdenum, has been little used in ferritic high-temperature steels. As a result, very few investigations have been made of its high-temperature strengthening ability, and reliable data on its effectiveness are not available. Grün rated tungsten far less effective than molybdenum at 930°F (500°C) on a weight-percentage basis.' However, Tammann has found that tungsten is as effective as molybdenum in raising the recrystallization temperature of iron. For this reason Smith, in a review of the subject, has advocated a re-examination of the influence of tungsten on the high-temperature strength of steel.' In any study of the effects of alloying additions on high-temperature properties, recognition must be made of the many variables involved, some of which can be controlled but have been ignored in innumerable investigations of the past, and some of which are difficult or even impossible to control. One cannot, for example, assign a definite strengthening index to any one alloying element, for this will be dependent upon the microstructure (heat treatment and mechanical treatment), testing con- ditions (temperature, time, and stress), and the complete composition of the steel (accompanying alloying elements, impurities, etc.). One ever-appear ing variable, hardness or tensile strength at room temperature, may be eliminated by heat treating all of the alloys to a single hardness level. An attempt may be made to control the variable of primary quenched structure by oil or water quenching the test specimen. The control of such variables may not be possible in cases of widely varying compositions, but at least such deviations should be recognized. Material and Procedure The alloys, made as 30-lb ingots in an induction furnace, all had the same base composition of about 0.18 pct C, 0.85 pct Mn, and 0.48 pct Si. They were grouped as follows: Mo Group—Containing up to 5.2 pct Mo. W Group-Containing up to 6.0 pct W. V Group—Containing up to 3.3 pct V. Mo-V Group—Containing up to 2.7 pct Mo and up to 1.4 pct V. Mo-W Group—Containing up to 2.5 pct Mo and up to 2.5 pct W. The steels, listed in Table I, were forged to ¾ in. sq bars and the material for the high-temperature, rupture-test specimens was further swaged to %-in. round bars.

Jan 1, 1957

By D. J. Weintritt, R. G. Hughes

Statistics show arz increase in the average depth of wells drilled in recent years. As a corollary to this trend, drilling fluids have been improved in an effort to meet the problems inherent at temperatures approaching 500°F. Of importance are (1) deterioration of mud components and (2) the effect of solids on filtration and rheological properties. High-temperature, stable water-base and oil-bare muds are discussed. Those areas in which differences exist are pointed out. Results are based on data taken from the Fann consistotneter, rheometer and shear-strength measurements, static and dynamic filtration tests, methy-lene blue test for bentonite solids and specific heat measLrrenlents of muds. INTRODUCTION Higher well temperatures go along with the fact that the average depth of wells continues to increase. Recent data by Gardner' lists 137 completions deeper than 15,000 ft for the first half of 1964 with a record second-half total of 167 wells drilling or proposed. In addition, there has been an increase in drilling for steam for power production or mineral recovery. In this application the depths are modest, but the mud may approach the critical pressure and temperature of water. Scearce and Magnon' report drilling mud used at temperatures of about 700°F in the Salton Sea area of California. Most deep wells have been drilled with water-base muds. In recent years, however, there has been a substantial increase in the use of oil-base muds because of technological advances in effective additives. The significance of this development was dealt with in considerable detail by Simpson and his co-workers.3 Additiona1 field data have now been obtained to indicate that oil muds are competitive in control, performance and cost with the best types of water muds for use at high temperaturc. This parallel offer of two very different fluid systems, each offering a similar variability in performance, cost and convenience, has created the need to evaluate the merits of these fluids under specified conditions so that the advantages and disadvantages of each can be weighed in relation to the over-all drilling program. This paper is not intended as a review of all the factors. Rather, it attempts to emphasize: (1) important condltions and facts peculiar to high-temperature drilling muds, (2) that more than one imposed test condition or testing method is necessary to describe the quality of a mud at high temperature and (3) that elaborate experimental precautions are necessary whenever laboratory data are used in selection of a mud for field use. WHAT IS A HIGH-TEMPERATURE DRILLING FLUID? For the purpose of this discussion, a high-temperature drilling fluid is any system so formulated or treated to economically minimize the effects of temperature on the properties of the fluid. Our experience in drilling fluids suggests that these effects become obvious for many mud materials at temperatures of 300F or higher. It is understood that hydrolysis of starches, depoly-merization of certain organic thinners, or irreversible chemical reactions (such as that of clay and lime) can affect filtration, viscosity and shear strength at less than 300F. However, the temperature level is not a serious point and in no way affects the precautions and techniques used in this study. An up-to-date review of the literature on high-temperature drilling fluids and the many variations was treated by Rogers'in 1963. EXPERIMENTAL REQUIREMENTS TESTING EQUIPMENT AND PROCEDURES With the advent of deeper drilling and increased demand for temperature-stable drilling fluids, new testing equipment and laboratory techniques were devised for the evaluation of drilling fluids subjected to elevated temperature and pressure. While the equipment has not been standardized, it is in widespread use. Milligan et al. Qescribe a filtration cell for determining the filtration properties of drilling fluids at temperatures in excess of 300F. They showed the effect of variations in temperature and pressure on oil and water muds filtered in the 300 to 400F range. The dynamic filtration apparatus described by Simpson6 permits the study of the filtration properties to temperatures of 350F for drilling fluids circulated over sandstone cores. Watkins et al.' describe the use of pressure bombs for studying the effect of prolonged periods of elevated temperature upon the gelation or solidification of drilling fluids. Chisholm et a1.' describe the use of a modified cement consistometer adapted for use in drilling fluid evaluations. A similar consistometer is used in this study, although the application and data-recording method have been changed. The consistency of a mud sample is measured by timing the movement of a soft iron bob which is magnetically moved up and down in the sample container.* Changer in the time of travel and the temperature of the mud at that moment are plotted with a two-point Brown Elec-tronik Recorder. A 10-in. chart with a speed of 4-in./hr is used. Fia.- 1 is a generalized internretation of the data ob-

Jan 1, 1966

Jan 1, 1900

By Avnulf Muan, Egil Aukrust

The activity-composition curve for cobalt oxide in (Co,Fe)304 solid solutions with spinel-type stmcture has been determined experimentally by studying the equilibrium between the spinel phase and a coexisting cobaltowüstite phase, "(Co,Fe)O", at 1200°C. A large negative deviation from ideal behavior prevails in the spinel at low cobalt oxide concentrations and a positive deviation at high cobalt oxide concentrations. The activity-composition curve for iron oxide in the solid solution is determined from the above curve by integvation of the Gibbs-Duhem equation along the join Co3O4,-Fe3O4. The standard free energy of formation of cobalt ferrite, CoFe2O4, from the oxide components CoO and Fe2O3 is calculated to be -8.2 kcal. ThERMODYNAMIC properties of (CO,Mn)3O4 solid solutions with spinel-type structure have been presented recently.' The present paper deals with similar relations in another spinel solid-solution phase, that represented by the system Co3O4-Fe3O4. The principles involved in measurements and calculations of thermodynamic properties for the system Co3O4-Fe3O4 are analogous to those used and discussed in detail in the work on (CO,Mn)3O4. A (CO,Fe)3O4 solid solution coexists in equilibrium with a (Co.Fe)Ot solid solution over a considerable Here acOo1.33 and aao are the activities of cobalt oxide in the spinel and the oxide solid solutions, respectively, pO2, is the oxygen pressure of equilibration, and pb, is the oxygen pressure at which CoO and CosO4 coexist in equilibrium in the binary system Co-O at the same temperature. The activity-com position curve for cobalt oxide in the (Co,Fe)O solid solution in contact with metal has been determined in a previous investigation by the present authors.' The system shows a small positive deviation from linear behavior. Because of the large defect concentration in wiistite and in (Co,Fe)O solid solutions, one cannot assume that the activity-composition relations in the oxide phase coexisting with a spinel phase at relatively high oxygen pressures are the same as those prevailing in the oxide solid solution coexisting with metal. However, a Gibbs-Duhem integration over the ternary Co-Fe-0 solution can be used to determine activities of cobalt and iron, and hence of CoO and FeO, from a knowledge of the oxygen potentials. Several papers have dealt with the subject of application of the Gibbs-Duhem equation to multi-component systems. 3-6 In the present case, it was

Jan 1, 1964

[IRVING, JOHN D. :-(Continued.) Some Features of Replacement Ore-Bodies, and the Criteria by Means of Which They May be Discovered, XLII, [xlvii]. Discussions: on A Concise Method of Showing Ore-Reserves, XLIII, 714; on The Iron Deposits of Daiquiri, Cuba, LIII, 65; I on Recrystallization of Limestone at Igneous Contacts, XLVIII, 214; I on To What Extent is Chalcocite a Primary, and to what Extent a Secondary, Mineral in Ore Deposits, XLVIII, 194. minerals of gold deposits, Homestake belt, Black Hills, S. D., XLII, 54.]

Jan 1, 1918

By H. H. Campbell

The following pages discuss some problems connected with the manufacture of steel by the open-hearth process. The methods employed necessarily enter into the domain of what is called theory; but the results are eminently practical. The determination of the various losses of thermal power and the investigation into the chemical reactions in the bath, are important to every manufacturer. It will be understood that definite figures concerning one furnace and one system, will not apply to all other furnaces and systems; but it is hoped that methods are developed, which are capable of general application and which will shorten the labors of others. The gas-calculations contain nothing entirely novel; but certain methods appeared to be very convenient and they are here elaborated in order that others may have a model to follow. The determination of the loss of iron by weighing the slag and finding the percentage of iron therein, is probably unusual. If so, the fact is to be regretted, since this is the only way that an accurate result can be obtained. The common method of estimating the loss in open-hearth work, is to subtract the weight of metallic products from that of the materials charged. Nothing could be more unsatisfactory, inaccurate and meaningless. Pig-iron, steel, wrought-iron and ore are charged into the furnace; complicated chemical reactions occur; the sand of the pig-iron, the slag from the wrought-iron, the gangue of the ore, all rise to the top ; the silicon, manganese and carbon burn and leave the metal; some of the iron oxidizes and goes into the slag; some of the ore is reduced and gives up metallic iron ; the recarbonizer is added, the mission of which is to waste itself; in the pouring of the steel, pit-scrap is made in the ladles, around the moulds and under the spout; the errors in weighing the products join hands to make accuracy impossible; and then the " loss" is determined by diffrence !

Jan 1, 1891

By John A. Gann

THE Iron and Steel Division has shared in the general increased activity of the industry. The fall meeting at Chicago was not only well attended but particularly characterized by the virility and scope of the discussions at the various sessions. The program for the February meeting indicates a similar interest in technological developments. The Blast-Furnace Committee continues to have the hearty support of the industry with discussions of such a nature as to be of real help to the operator as well ass the technologist. The work of the Open-Hearth Committee continues to be outstanding, with ever increasing attendance and ever mounting interest in the meetings. Formation of a conference on the physical chemistry of steelmaking has given those interested in this phase of work an organization allowing the same

Jan 1, 1936

By A. J. Griest, P. D. Frost, H. A. Robinson

The flow characteristics and uniform elongation of alpha-beta titanium alloys in the solution-treated condition were shown to be markedly affected by the solution temperature. Two classes of alpha-beta alloys were distinguished, based on the effect of solution temperature on the uniform elongation. Martensitic alpha-beta alloys, which are relatively weakly beta-stabilized, showed decreasing values of uniform elongation as the solution temperature was initially increased. However, after solution-treatment at still higher temperatures in the alpha-beta field, the uniform elongation of these alloys was again high, and often attained its maximum value. Nonmartensitic alpha-beta alloys, which are more heavily beta-stabilized, showed a continuous decrease of uniform elongation with increasing solution temperature. The behavior was rationalized in terms of the alpha-beta ratio and the alloy content of the beta existing at the solution temperature. The data indicate that in commercial practice close temperature control may be required to get maximum uniform elongotion, and hence, maximum potential formability, in solution-treated sheet. Bend-test data also were obtained for the solution-treated conditions. A MOST important objective of current titanium research is the development of age-hardenable alloys with superior formability in the solution -treated condition. Alpha-beta titanium alloys have been shown to be amenable to high-strength aging treatments after solution-treatment in the alpha-beta field.' However, heat-treatment data on the properties of solution-treated sheet, such as uniform elongation, minimum bend radius, and flow properties, which have a bearing on the potential formability, have not been widely available. This paper presents only the most significant results of a research program conducted at Battelle for the Air Force in an effort to develop sheet alloys that can be formed readily as solution-treated and subsequently aged to very high strengths. Data for 10 compositions representative of the more than 25 alloys studied in this program are presented. A primary objective of the paper is to demonstrate the pronounced dependence of the flow characteristics and uniform elongation on solution-treatment temperature. This effect is believed to be vitally important in the commercial heat-treatment of age-hardenable titanium sheet alloys. Experimental Procedures Melting and Fabrication—The nominal and actual compositions, beta transi temperatures, and rolling temperatures of 10 of the 30 alloys studied are presented in Table I. Stock :€or two of the alloys, E (Ti- 8Mn) and J (Ti-6A1-4V) was obtained from commercial heats. The remaining heats, except D and I, were double melted as 10-lb heats in a consumable-electrode furnace. Melting stock was 120 Brine11 hardness sponge. The oxygen and hydrogen analyses spotted throughout the heats indicate the range of interstitial levels resulting from the melting practice used. Heats D and I were melted as 20-lb ingots with the same grade of sponge. These ingots were cut in half and one portion used in the present evaluation. The ingots, which were about 4 in. diam and 4 in. in height, were upset forged and drawn at 1750°F to sheet bar 5/8 in. thick by 2 1/2 in. wide in such a manner that the top of the ingot corresponded to the top of the sheet bar. Slabs of the sheet bar, 5 1/2 in. in length were scalped to 1/2 in. thickness and rolled at the temperatures indicated in Table I to approximately 0.055 in. sheet. Elongation during rolling took place at 90" to the original forged length. The fabrication procedure used is described in some detail since the experimental heats showed considerable directionality in mechanical properties. The rolling procedures for the commercial heats were unknown, but were such as to produce essentially isotropic properties. All heats, as rolled, showed microstructures typical of alpha-beta alloys worked in the alpha-beta field; that is, the structures consisted of equiaxed alpha particles in a beta matrix. Heat Treatment— The effects of solution and aging heat-treatments on the properties of the alloys were evaluated uSing longitudinal and transverse tensile and bend coupons sheared from the sheet. Two or three solution-treated conditions were evaluated for each alloy. In addition, the alloys were also tested after annealing at 1200°F for 4 hr and furnace cooling. The solution-treated and annealed conditions were those in which the alloys might be expected to

Jan 1, 1959

By R. W. Cahn, C. D. Graham

The rate of growth of a single grain growing into a strained aluminum single crystal, measured by the conventional heat-cool-etch technique, is shown to decrease with time at temperature. The growth rate measured by means of X-rays, with the sample continuously at temperature, is found to be linear. Evidence is presented to show that the decreasing growth rate obtained by the conventional technique is due to abnormal recovery in the strained grain, and that the recovery in turn results from the heating and cooling cycles, rather than from the effects of etching. The experimental apparatus is described in an appendix. FREQUENTLY, the rate of grain boundary motion during recrystallization is determined by heating a sample to a known temperature for a given time, cooling to room temperature, and etching to reveal the boundary position. The cycle of operations is repeated as many times as necessary to establish the rate of boundary motion. Although this heat-cool-etch technique has been used by a number of workers over a period of many years,'-!' other investigators have encountered difficulty with the method."'. " They have attributed the erratic results to the effects of repeated heating and cooling, or of etching, or both, and have adopted an alternative experimental procedure in which a number of identical samples are employed, each sample being cooled and etched only once. This alternative method ove1.comes some difficulties, but introduces others. In particular, the incubation periods of the observed grains are unknown: any effect of crystal orientation on growth rate cannot be determined easily. A preferable method would be to measure the motion of a recrystallizing grain boundary with the sample at temperature without etching," but such measurements have in the past been restricted to nonmetals. This paper describes the construction and operation of a device, the goniometer furnace, with which the position of a moving grain boundary between a recrystallizing grain and the strained single crystal into which it grows can be measured by means of X-rays, with the sample maintained continuously at temperature. Goniometer Furnace The operating principle of the goniometer furnace is shown in Fig. 1. The sample, in the form of a bicrystal strip, is surrounded by a furnace, not shown in the sketch, and can be rotated about the two axes A and B which intersect at the point where the X-ray beam strikes the strip. The strip is oriented so that one of the two grains gives a strong Bragg reflection, which is detected by a suitably placed Geiger-Miiller counter coupled to a counting-rate meter When the strip is moved parallel to its own length in the furnace, arrow C, so that the X-ray beam strikes the second grain, there is in general no strong reflection. By noting the position of the strip at which the drop in Geiger counter reading occurs, it is possible to determine the position of the boundary. Measuring the change in boundary position with time at temperature gives the rate of growth of the recrystallizing grain. Details of the construction and operation of the goniometer furnace are given in the Appendix. Measurements showed that the temperature in the furnace was uniform within ±10°C over its working length of about 28 cm. The temperature at the measuring position, i.e., at the point where the X-ray beam struck the sample, was estimated to be constant within ±2oC. Using the goniometer furnace, the position of a stationary boundary could be measured with a reproducibility of ±0.3 mm. At elevated temperatures, 500" to 625"C, with the boundary in motion and the X-ray reflection less sharp, the estimated accuracy of each measured boundary position dropped to about ±1 mm. Experimental Results The test pieces were single crystals of 99.6 pet A1 —principal impurities 0.19 pet Fe and 0.12 pet Si— 1 mm by 1 cm in cross section and 6 to 10 cm in length, grown by the strain-anneal method. This relatively low purity material was used because of the difficulty encountered in producing strain-anneal single crystals of very high purity—99.996 pet—

Jan 1, 1957

By R. W. Fountain, J. Chipman

THE solubility of nitrogen in iron and steel has been of considerable interest due to the role of nitrogen in strain-aging and in quench-aging. It is generally considered that quench-aging is the result of precipitation of carbide and nitride particles from supersaturated solid solution, while strain-aging results from the segregation of carbon and nitrogen atoms to dislocations.1-9 The rate of strain-aging is controlled primarily by the amount of carbon and nitrogen in solution and the temperature. In experiments on strain-aging of pure iron with only carbon or nitrogen as impurities, Fast" has shown that even after 40 hr at 50°C carbon did not give any strain-aging while

Jan 1, 1959

By R. E. Zimmerman

ALTHOUGH flotation of coal is considered relatively new in the United States by coal-preparation engineers, actually it has been practiced to some extent for the past 30 years, It is practiced much more widely in Europe than in the United States. Commercial plants are operating in nearly all major coal-producing countries of the world. A froth flotation plant has been operating since 1930 at the Champion No, 1 preparation plant of the Pittsburgh Coal Co. Unfortunately the term flotation is widely used in the United States by coal-preparation engineers to designate dense medium processes of coal cleaning. As used here, flotation means those processes for cleaning fine sizes of coal in which the coal is collected in a froth or matte at or near the surface of a pulp. The refuse particles remain in the pulp. Two distinct types of flotation are practiced: froth flotation and agglomeration. FORMS OF FLOTATION The theory of the principles of flotation and of the physicochemical foundations surrounding this process has become a complex and scientific field and coal-preparation engineers contemplating use of flotation processes would do well to study the works of Gaudin, 2, 5 Taggart, 3 Zimmerman, 4 Wark, 6 Ralston, 7 Petersen. 8 Bulk Oil Flotation.-In this process the separation of mineral from gangue is accomplished by virtue of the fact that minerals of metallic lustre, as sulphides, or hydrocarbons, as coal and graphite, are wetted preferentially by oil in the presence of water and consequently pass into the interface between oil and water; while gangue or rock is wetted by water and remains in the medium. Beginning in 1860 with Haynes and later between 1897 and 1907, at least 25 patents were granted for bulk oil flotation. Large quantities of oil are required, generally 3 to 25 per cent by weight of feed, and recovery of such oil is a major problem. The Elmore process 3 (1901 and 1902) is an example of a bulk oil process, The Trent process (1902-25) has been used for the cleaning of coal on a commercial scale, According to E. W, Davidson 9 there were five such plants operating in the United States by 1925. They have since been abandoned.

Jan 1, 1950

New Jersey Zinc Co. - The Plants Canon City Palmerton Depue

Jan 12, 1953

By K. M. Rolls, R. M. Rose, H. B. Shukovsky

Studies of the phase structure, critical current density, and resistive critical magnetic field of a 45 pct Nb-55 pct Zr superconducting alloy after final-size heat treatments are reported in this paper. A combination of optical metallography, X-ray diffraction, and electrical-resistivity measurements were used to determine the phase structure. Superconductivity measurements, made with heat-treated wires, are correlated with microstructure. Although no quantitative relationship between microstructure and critical current density is found, it is shown that SINCE Kunzler1 as well as Berlincourt, Hake, and Leslie2 first described the high-field, high-current-density superconductivity of Nb-Zr alloys, it has be- the critical current density is highest when the microstructure is finely divided by fibering, coring, precipitation, or fine-scale phase dispersions. The resistive critical field is very sensitive to the compositions of the phases present. Since the alloy investigated here is near the maximum resistive critical field for the Nb-Zr system, any phase decomposition results in a lower H,. Elimination of the effects of cold work lowers H, also. A possible interpretation of the latter in terms of internal surface superconductivity is suggested. come apparent that the resistive critical field and the current-carrying capacity of such alloys are, in large measure, dependent on composition and processing. The resistive critical magnetic field (Hr) for low current densities has been found to increase progressively with zirconium content until a flat maximum is reached between 50 and 65 pet Zr.3 For any single composition, a characteristic maximum value of H, is attained by heavily cold-drawn wire.4 critical current density (J,) depends not only upon cold work but also, apparently, upon microstructure. Heat treatments of cold-worked wires generally

Jan 1, 1965

By Norman B. Pilling

The technical difficulties hampering the metallographic analysis of silicon steels are chiefly the result of the extreme corrodibility of these alloys. The addition of silicon to iron in increasing quantities, up to about 6 per cent., rapidly increases the susceptibility of the alloy to chemical attack, not only in acid solution, but in water. This renders the preparation of metallographic sections very difficult, because of a non-selective attack upon the finely polished surface by the water used as a lubricant in polishing. This water attack masks the true structural details revealed by suitable etching reagents. It is thus necessary to use alcohol as a polishing lubricant in the last stages of preparation and to avoid all etching reagents having an aqueous base. A specific reagent for the identification of iron carbide in ferrous alloys, and the one hitherto used almost' exclusively by metallurgists, is an alkaline aqueous solution of sodium picrate, which stains this constituent selectively. Its application to silicon steels has not proved successful, as its distinctive selective action is more or less completely hidden by the general attack of the aqueous solvent on the silico-ferrite, greatly accentuated by the fact that this reagent must be used at its boiling temperature (105' C.). Thus, a powerful metallographic aid to the study of the higher silicon alloys, such as transformer steels, is lost. A new reagent has been developed for the purpose of overcoming this difficulty. It is with some hesitation that the list of etching reagents, already overburdened, is increased, but the properties of this new reagent are advantageous in several ways and a definite field for it may be found in the metallography of ferrous alloys. The reagent consists of a dilute solution of nitric acid and methyl alcohol in nitrobenzol. It is a great advantage to secure an anhydrous solution, as a tendency toward acidic etching has been traced to small amounts of water. A convenient method of preparation is to make an anhydrous stock solution of nitric acid in methyl alcohol in the proportion 20 per cent. acid by weight (12.5 per cent. by volume). The alcohol can

Jan 1, 1924

By P. A. Beck, S. Kohara, M. N. Parthasarathi

IT has been shown1,3 that many observed phenomena related to annealing textures in f.c.c. metals can be adequately accounted for, at least in a qualitative way, by considering the orientation dependence of the boundary mobility, without any hypotheses concerning preferred orientation of nuclei. It was noted1 that this approach is particularly successful in the common cases of primary recrystallization in highly cold-worked polycrys-talline metals, where nuclei occur in great abundance, and that in the other extreme case, where the number of nuclei is very limited, or even only a single crystal is grown, the orientation dependence of boundary mobility has only a small effect, or none at all, on the orientations resulting from annealing. Recently Dunn described examples3-6 where observed secondary recrystallization textures apparently cannot be accounted for on the basis of oriented growth alone, but also require oriented nuclei, or at least the absence of nuclei in certain orientation ranges. In general, the great difficulty in correlating the preferred orientation of recrystallized grains with that of nuclei is inherent in the fact that nuclei are by nature very small, and that they are usually identifiable as "nuclei" only after growth, i.e., after they have already been subject to growth selectivity. An investigation was carried out by Liebmann and Lücke,' and also a very similar one by Graham and Cahn,' to obtain quantitative information on the orientation depend- ence of boundary migration rates in the recrystallization of slightly deformed aluminum single-crystal rods or plates, in which artificially nucleated recrystallized grains of predetermined orientation were grown. Liebmann and Lücke foupd maximum boundary mobility for boundaries across which the misorientation corresponded to a rotation of 40 deg around a common [Ill] axis, in accordance with earlier conclusions.9,1 Also, they confirmed that such an orientation relationship predominates among crystals growing into slightly extended single crystals from presumably random artificial nuclei. On the other hand, Graham and Cahn found no preferred orientation among crystals grown in a similar manner. It is not as yet known how these observations may be reconciled with each other. The view has been expressed in various papers5'10,21 that selective growth based on the orientation dependence of boundary mobility is not in itself sufficient to account for the formation of sharp re-crystallization textures, such as those often observed in highly deformed polycrystalline metals after annealing. The present work was undertaken to ascertain whether or not it is possible to obtain a sharp re-crystallization texture in a case where random nuclei are assuredly present in large numbers. It was previously found1' that high-purity aluminum crystals rolled 80 pct on the (110) plane in the [1T2] direction, when suitable precautions are taken, may be annealed for periods of about 1000 sec at 350°C without recrystallization. It was also found that the reluctance to recrystallize in this case is due to the scarcity of material in sufficiently deviating orientations to serve as nuclei. By using such a matrix,

Jan 1, 1959

By F. Keller, J. D. Edwards

The anodic treatment of aluminum presents problems of scientific as well as of commercial interest.l-3 Of particular interest is the fact that, during the anodic oxidation process, the oxide continues to form at the metal-oxide interface under any oxide previously formed. This has led to speculation as to the mechanism involved in the formation of the relatively thick oxide coatings that are used commercially for decorative or protective purposes. Furthermore, the ability of certain types of oxide coatings to adsorb dyes and other substances has stimulated research to determine the actual structure of these adsorptive coatings. It has been found that anodic oxide coatings on aluminum are composed essentially of aluminum oxide. They are formed by the action of oxygen ions penetrating to the metal surface during the electrolytic oxidation treatment. These coatings can be formed in a number of different electrolytes, as for example, those which contain sulphuric acid, chromic acid, oxalic acid, or boric acid. These are the commonest and most useful electrolytes employed commercially. Except for certain specific conditions of formation, the coatings in general have been found to be amorphous alumina, as far as can be determined by X-ray or electron-diffraction methods. Anodic oxidation processes can be arranged in three rather general classes if they are grouped in relation to the solvent action of the electrolyte on the coating.4 In the first class, the electrolyte has little or no solvent action on the coating that is formed. In general, coatings produced under such circumstances are nonporous and non-adsorptive. In the second class, the electrolyte exerts an appreciable solvent action on the coating. These coatings are porous and adsorptive. Finally, for the third class, the electrolyte tends to dissolve the coating about as rapidly as it is formed. This action produces electrolytic brightening or anodic polishing of the aluminum surface and at most leaves only a very thin film of oxide. The nonporous and nonadsorptive type of oxide film is represented by the coatings that are formed when solutions of boric acid are employed as the electrolyte. It is especially significant that these impervious films are formed in electrolytes that exert little or no solvent action on the coating. Where a boric acid electrolyte is used, the coating tends to form rapidly, with the result that the flow of current is soon reduced to substantially zero. This indicates that the growth of the coating has stopped. As a rule, the thickness of the coating is roughly proportional to the voltage employed for formation and the coatings of this type are exceedingly thin. In an electrolyte of this type, the coating has a high resistance when the aluminum is made anode; consequently, any current that may flow (leakage current) is very

Jan 1, 1944

By F. Keller, J. D. Edwards

The anodic treatment of aluminum presents problems of scientific as well as of commercial interest.l-3 Of particular interest is the fact that, during the anodic oxidation process, the oxide continues to form at the metal-oxide interface under any oxide previously formed. This has led to speculation as to the mechanism involved in the formation of the relatively thick oxide coatings that are used commercially for decorative or protective purposes. Furthermore, the ability of certain types of oxide coatings to adsorb dyes and other substances has stimulated research to determine the actual structure of these adsorptive coatings. It has been found that anodic oxide coatings on aluminum are composed essentially of aluminum oxide. They are formed by the action of oxygen ions penetrating to the metal surface during the electrolytic oxidation treatment. These coatings can be formed in a number of different electrolytes, as for example, those which contain sulphuric acid, chromic acid, oxalic acid, or boric acid. These are the commonest and most useful electrolytes employed commercially. Except for certain specific conditions of formation, the coatings in general have been found to be amorphous alumina, as far as can be determined by X-ray or electron-diffraction methods. Anodic oxidation processes can be arranged in three rather general classes if they are grouped in relation to the solvent action of the electrolyte on the coating.4 In the first class, the electrolyte has little or no solvent action on the coating that is formed. In general, coatings produced under such circumstances are nonporous and non-adsorptive. In the second class, the electrolyte exerts an appreciable solvent action on the coating. These coatings are porous and adsorptive. Finally, for the third class, the electrolyte tends to dissolve the coating about as rapidly as it is formed. This action produces electrolytic brightening or anodic polishing of the aluminum surface and at most leaves only a very thin film of oxide. The nonporous and nonadsorptive type of oxide film is represented by the coatings that are formed when solutions of boric acid are employed as the electrolyte. It is especially significant that these impervious films are formed in electrolytes that exert little or no solvent action on the coating. Where a boric acid electrolyte is used, the coating tends to form rapidly, with the result that the flow of current is soon reduced to substantially zero. This indicates that the growth of the coating has stopped. As a rule, the thickness of the coating is roughly proportional to the voltage employed for formation and the coatings of this type are exceedingly thin. In an electrolyte of this type, the coating has a high resistance when the aluminum is made anode; consequently, any current that may flow (leakage current) is very

Jan 1, 1944