Search Documents

By J. E. Ostberg, G. Phragmen, A. Hultgren, S. Wohlfahrt

Detailed study was made of a number of rimming ingots, both low and high carbon, and especially upon effects of superimposed air pressure. Requirement to suppress core bubbles is between 10 and 15 atm; at 6.5 atm freezing was in semikilled manner and at 3 atm, steel was of rising type. Probable mechanism of freezing under various conditions is discussed. AN earlier paper' reported an investigation made by a committee for studying rimming steel ingots appointed by Jernkontorets in Stockholm. The present paper is the outcome of some further work done by the same committee. Since the characteristics of ordinary rimming steel are connected closely .with the amount of gas liberated during freezing and since this amount of gas is governed by the pressure, it was considered of interest to ascertain in what manner and to what extent definite pressures applied to the top of the liquid steel in the mold would affect the solidification process and the consequent structure of a rimming steel of ordinary composition. The experiments were made at the Domnarfvets Steel Works. The steel was made according to normal practice in a 4-ton Rennerfelt electric furnace. Ferromanganese was added in the furnace; no aluminum was added, with one exception. Analyses of the four heats are given in Table I. The top-poured ingots measured about 12 in. sq x 48 in. and weighed about 1300 lb. One or two ingots of each heat were allowed to solidify under pressure, using a special device for admitting compressed air to the upper closed part of the mold, as shown in Fig. 1. A heavy plate sealed with asbestos was bolted to the top of the mold. The plate had a tapered aperture for pouring. Immediately after pouring the hole was closed by a wedged plug, and compressed air was admitted through a hole in the plug. Because of some delay in applying the plug, full pressure was not reached immediately. The pressure was adjusted to the desired value as indicated by a manometer. In order that the interior of the ingot might have the benefit of the pressure, the freezing of the top crust was delayed by a refractory lining applied to the top part of the mold, Fig. 1. Ingots were also cast from each heat without applied pressure, and with and without refractory lining at the top. Axial sections of ingots were cut either of the whole ingot or of some part of it of special interest; sections were polished and usually etched.' To facilitate description of structures the following terms may be used for different types of ingots solidified under gas evolution: 1. Box-hat or boot-leg ingot: Abundant gas evolution during casting and during rimming; no rim holes. 2. Normal rimming ingot: Lively gas evolution during rimming; usually rim holes in lowest part of

Jan 1, 1952

Jan 1, 1912

By H. M. Conger

Kaiser Steel Corporation's Eagle Mountain mine is located in the Colorado Desert, 60 miles east of Indio, California. Iron concentrates from the mine are shipped by rail 164 miles to the' Company's steel mill at Fontana, and also to Longbeach, California for export. Temperatures are typical of the lower desert ranging from a high of 120 degrees in the summer to a low of 25 degrees in the winter. The average, annual rainfall of about two inches comes mainly as cloudbursts during the summer months. From its inception, the Eagle Mountain mine has had the problem: of breaking its mine rock. Practices followed from 1949 until 1962 were very costly, did not produce uniformly good fragmentation, and were incapable of sustaining, high production. During this period, every conventional type of explosive was tried and found to be unsatisfactory for one reason or another.

Jan 11, 1965

By Elbert Rowland

THE widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the strongest nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation-hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-Al and Cu-Zn, among others, exhibit promising improvements in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those realized from the binary copper-beryllium alloys, excellent properties are obtained with beryllium contents averaging about one-half the amount required in the binary alloys. This paper presents the results of an investigation of the equilibrium relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of

Jan 1, 1935

By J. S. Dodge, I. M. Krieger

The laminarturbulent transition was studied for monodisperse rigid polymer latices as functions of particle diameter and concentration at several tube diameters. Breaks in the graph of friction factor US Reynolds number were used to characterize the transition; rates of shear were sufficiently high so that Newtonian behavior at the high shear limiting viscosity could be assumed. No abnormal behavior was noted at concentrations below 30 volume percent. At higher concentrations, suppression of turbulence was observed with critical Reynolds numbers rising to as high as 5,500 at 50 volume percent. No definite effect on the transition was noted due to variation of particle size or tube diameter. The type of surfactant used to stabilize the latex was found to have an important influence on the critical Reynolds number. INTRODUCTION For some polymer solutions and solid-in-liquid suspensions, the transition from laminar behavior to turbulence in pipeline flow has been reported to take place at unusually low1-5 and in some cases at higher than normal6,7 critical Reynolds numbers. Extreme values of critical Reynolds numbers (NRe*) have been found to range from 1 to 6,000, as opposed to the values of 2,000 to 3,500 which are obtained for ordinary liquids. Observations have also been reported of drag reduction in fully developed turbulent flow, i.e., a decreased value of the friction factor in the Reynolds number-friction factor plot6*10-14 in colloidal and polymeric fluids. In some cases, turbulence suppression (unusually large values of Nre*) was noted to occur preceding the drag reduction,6 while a normal transition was noted in other cases of drag reduction.14 To relate the occurrence of turbulence suppression and drag reduction to the molecular or particulate structure of the fluid, it is desirable to characterize the structural variables with some precision. For most colloidal dispersions and polymeric fluids, this is very difficult; particle sizes, shapes and stiffnesses may vary over wide ranges in the same sample. Recently, however, a colloidal fluid has become available which consists of rigid spherical particles of highly uniform diameter dispersed in a simple Newtonian liquid. These are monodisperse polymer latices, prepared by carefully controlled emulsion polymerization reactions. The purpose of this research was to study the transition to turbulence in these well-characterized colloidal fluids as a function of concentration, particle diameter and tube diameter. Typical flow curves of latices of high solids content are shown in Fig. 1. While these curves were obtained with monodisperse latices, the general shape of the curve is also typical of a polydisperse latex. It is observed that a shear-thinning region occurs for low to moderate rates of shear. At sufficiently high shearing rates a limiting Newtonian viscosity is reached. The viscosity µ diminishes with decreasing volume fraction 4 at all shear rates. For 4 less than 0.25, latices are Newtonian at all rates of shear.15 An increase in average particle size (at a given extends the Newtonian viscosity region to lower rates of shear. A third factor which influences the

By B. L. Averbach, M. Cohen

THE PROBLEM MANY hardened steels contain significant quantities of retained austenite even in cases where the carbon and alloy contents are low. In fact austenite has been detected in plain carbon steels containing as little as 0.50 pct carbon.1 Although the austenite may not be visible metallographically it causes definite dilatometric and magnetic effects during subsequent tempering or subatmospheric cooling.1,2,3 Therefore if the reactions which hardened steels undergo during later treatment are to be understood in quantitative fashion it is most essential to have some kind of absolute analysis for the austenite content in hardened steels. Once this analysis has been made, the austenite transformations can be followed precisely by observing such sensitive phenomena as changes in length or in magnetization but the latter techniques can only determine differences in the amount of retained austenite and usually an independent method must be found to put these differences on an absolute basis. In certain instances the microscope can be used advantageously to determine the percentage of retained austenite. The quenched sample is tempered to "darken" the martensite with minimum decomposition of the coexisting austenite, and then is polished and etched in the usual fashion. If the austenite is clearly distinguishable from the tempered martensite and other possible constituents its volume percentage can be measured quantitatively by point counting or lineal analysis.4 Such microscopic methods, however, depend on the etch being sufficiently discriminatory. In fairly coarse structures, if the austenite content is greater than 10-15 pct, there is probably little smearing of the etch, and point counting or lineal analysis seems to be quite accurate. On the other hand if the structure is difficult to resolve, as in commercially treated fine-grained steels which contain less than 10-15 pct retained austenite, the latter may be completely obliterated by the dark etching martensite or it may appear disproportionately low as the interfaces between the two constituents become difficult to distinguish. Another disadvantage of the metallographic method is the need for "darkening" the martensite and hence the determination cannot be applied to as-hardened steels. The required tempering may spoil the structure for other tests or may even remove a small part of the austenite which is being sought. X ray methods hold more promise for covering the range under 15 pct retained austenite. Although austenite and martensite in the hardened steel may be chemically identical, their crystal structures and lattice parameters differ, and the intensity of an austenite diffraction line is some continuous function of the percentage of re-

Jan 1, 1948

By M. L. Rudee, R. A. Huggins

Samples of iron containing nitrogen or carbon have been given treatments similar to those used in cold-work peak (CWP) measurements and examined by transmission electron microscopy. It was observed that the unusual and nonreproducible behavior of the carbon CWP can be explained by a strong tendency for carbon to form grain boundary precipitates at temperatures below those used for CWP measurements. These precipitates dissolved at the temperatures used in the CWP measurements. There was no evidence for nitrogen precipitation at grain boundaries. There was no indication of precipitation along dislocations in either carburized or nitrided samples given treatments similar to those of CWP measurements. Although it is possible that subelectron-microscopic clustering had occurred, this observation supports the theories of the CWP that are based on continuous atmospheres rather than on individual precipitates. In an earlier paper,' the present authors developed a new distribution function to predict the occupation of sites for interstitial impurity atoms around a dislocation. When this distribution was applied to the case of carbon and nitrogen in iron, it predicted that, if the temperature dependence of the concentration of solute atoms in the matrix was controlled by the presence of equilibrium carbide or nitride precipitates, the tendency for nitrogen to segregate to dislocations would be greater than that for carbon even though their binding energies to dislocations are identical. The cold-work internal-friction peak (CWP) is considered by most authors to be produced by the interaction of interstitial impurities with dislocations. Many investigators have studied the CWP in iron containing carbon and nitrogen and have observed a significant difference between its behavior in the two cases. In this paper a series of experiments will be reported that were initiated to determine whether the application of the new distribution function would explain the observed differences between the carbon and nitrogen CWP. Although it was found that the distribution function, pev se, did not explain the differences, the differences became clear, and some insight into the mechanism of the CWP was realized. Before reporting the present experiments, the literature pertaining to the differences between the carbon and nitrogen CWP in iron and the various mechanisms proposed for the CWP will be reviewed. LITERATURE REVIEW Snoek2 first observed the CWP in iron specimens containing nitrogen, but also reported a weak and unreliable peak in carburized samples. Later, Ke3 established that the CWP height was proportional to the degree of deformation. The presence of nitrogen alone would produce a peak of the same size as found in a sample containing both nitrogen and carbon, and KG concluded that the CWP was caused by nitrogen. In a discussion of G's paper it was reported that Dijkstra had investigated the CWP in samples that contained only carbon. He found it to be much smaller than the nitrogen peak and "unstable". KG et al.4 charged specimens of iron with both carbon and nitrogen. They observed that the carbon CWP was much smaller than that observed in nitrided samples, but that aging at 300°C caused the carbon peak to increase. A similar treatment produced no change in a nitrogen peak. Annealing at higher temperatures caused the height of the CWP in both the nitrogen and carbon samples to decrease. This behavior was also observed by Kamber et al. 5 who found that the activation energy for the annealing of the CWP was identical with the activation energy for the self-diffusion of iron. They concluded that the annihilation of dislocations by climb caused the reduction in the CWP height. Kamber et al. studied the "unstable" carbon peak in detail. They measured both the Snoek and CWP during various aging treatments. In carburized samples, aging at 100°C caused the Snoek peak to disappear, although the CWP peak remained small. However, a subsequent treatment for 5 hr at 240°C caused the CWP to reach a maximum. They proposed that an additional location for the carbon, other than whatever site produced the CWP, is present. In nitrided samples the CWP was completely developed as soon as a measurement was made; additional sites are not present. No explanation of either the additional site or the difference in the behavior of carbon and nitrogen was offered. petarra5 performed a systematic study of the effect of composition on the CWP. Using three kinds of "pure" iron, he showed that there was a residual CWP when the carbon and nitrogen concentrations had been reduced to less than that detectable by Snoek-peak measurements. He observed the same general annealing behavior and composition dependence as previous investigators, with the following exceptions. On first measuring the carbon CWP, it was found to be identical with the residual peak, and essentially independent of the carbon content. If the CWP was measured a second time in the same sample, it increased in size, but was still only about one-fourth the size of a CWP in a sample of the same iron nitrided to the same composition. On the other hand, a series of annealing experiments showed that the nitrogen CWP was not al-

Jan 1, 1967

By D. R. Walker, M. C. Shaw

THE laws of comminution of Kick and Rittinger have been debated for many years. Certain data obtained from ball mill and drop tests are found to be in approximate agreement with Rittinger's law while other data would seem to support Kick's law. In all these tests the energy required to produce a wide variety of particle sizes has been studied. Surface area has also been measured with considerable difficulty, at first because it was thought that the energy associated with crushing was that required to create new surface, later because of precedent and because a more fundamental variable was unknown. Tests made with the machine shop type of grinding process show that normally brittle materials that are usually crushed can behave like the more ductile metals. Brittleness is then a relative property largely dependent on specimen size and stress state. The machine grinding operation offers a convenient means for studying the comminution of materials in which the important size variable retains its identity. The energy required to grind a certain volume of material is shown to be strongly de- pendent on size. Kick's law is found to hold very well for particles below 1 micron in size, while Rittinger's law holds approximately in the comminution of larger particles. While a physical origin of Kick's law is established in terms of the theoretical strength of materials having a perfect lattice structure, there is found to be no physical basis for Rittinger's law.

Jan 3, 1954

By H. Schwartzbart, J. R. Low

Annealed, .Poly crystalline, low carbon steel exhibits a phenomenon known as the "yield point." If such a steel is loaded in tension, the load increases steadily with elastic strain, drops suddenly, fluctuates about some constant load value for a time and then rises with further strain. The load at which the sudden drop occurs is called the "upper yield point"; the load at which deformation proceeds at constant load is known as the "lower yield point"; the amount of elongation at constant load is termed the "yield point elongation." Deformation which occurs during the yield point elongation is heterogeneous in nature, deformed metal existing next to undeformed metal. The drop in load from the upper yield point is concurrent with the formation of a band of deformed metal which usually appears at a stress concentration such as a fillet and at an angle of approximately 45" with the direction of pull. As deformation proceeds during the yield point elongation, the deformed region grows until the entire specimen has been strained an amount equal to the strain in the first band. A phenomenon very often associated with the yield point is that of strain aging. Aging in steels may be of two types: quench aging, or precipitation hardening, and strain-aging. Strain aging differs from precipitation hardening in that if the metal is merely strained instead of given a solution anneal and quenched, it then undergoes changes in properties similar to those observed in quench aging. The yield point effect and strain aging are most markedly exhibited by low carbon steel, but have been observed in other alloys. Numerous explanations for the mechanisms of both phenomena have been advanced, but the evidence for the acceptance of any of the hypotheses is incomplete. One of the explanations of the yield point phenomenon frequently proposed is that there exists a honeycomb of grain boundary material that supports the load above the yield strength of the ferrite and that when this network ruptures, the ferrite flows with no increase in load. This notion was first advanced by Dalbyl in 1913 and has been since put forward in more concrete form by many investigators. The testing of this hypothesis was, in part, the object of the present investigation. Similarly, the mechanism by which strain aging occurs remains to be explained. Presumably, it is a precipitation hardening phenomenon similar to quench aging, the precipitation being initiated by strain. However, it is not known whether the process is a solution and precipitation effect or a change in solubility due to strain. One obvious method of determining whether or not the yield point is a grain boundary phenomenon is to determine if single crystals exhibit a yield point. Low and Gensamer2 have shown that carbon and nitrogen are responsible for the yield point and aging in steel and that these effects can be eliminated by the removal of these elements through wet hydrogen purification. Single crystals that have been grown in wet hydrogen treated material must then be recarburized or re-nitrided in order to evaluate the effect of grain boundaries. In the present investigation, single crystals of iron which had been annealed in wet hydrogen to remove the carbon and nitrogen were cut into two specimens having the same orientation with respect to the tension axis. Of these, one specimen was pulled in tension in the wet hydrogen treated state and the other was carburized or nitrided and tested similarly. All the crystals were examined for a yield-point and strain aging. The grain boundary hypothesis for the explanation of the yield point in steel has been tested only indirectly previously. Arrowsmith,3 Andrew and Lee,4 Edwards and Pfeil,5 Fell,6 Ludwik and Scheu,7 Winlock and Leiter8 and others found a decrease in proportional limit and yield point effect with an in-

Jan 1, 1950

Alpha Portland Cement Co.'s mining operations at Manheim W. Va., produce 750,000 bbl of limestone yearly, averaging 2200 bbl per working day. Thirteen parallel entries have been driven to date, each almost 30 ft high and about 45 ft wide, extending back 5000 ft to the working faces. Pitch of the seam from the lowest to the highest entries is steep enough to provide excellent year- round natural ventilation, and this, together with the size of the entries and a good bottom, has allowed face crews to drive right up to the working areas in the family car.

Oct 1, 1956

By John D. Wiebmer

There are those in the Colstrip, Mont., area who can still remember the opening of the Rosebud mine in 1923. For 35 years it was a steady employer of 80 or 90 residents who produced coal for the railroad. In 1958, though, mining ceased as diesel locomotives supplanted steam engines. The mine was purchased in 1959 by Montana Power, the parent of Western Energy Co., and production resumed in 1968. Long Construction Co. was chosen as operator of the mine equipment. At that time, reserves appeared virtually unlimited. The thick Rosebud seam coursed through alternate sections of railroad holdings and federal land-then came the federal moratorium on coal leasing in 1971. About the time Western Energy completed the special leasing procedure to extend reserves from an existing mine, a new federal monkey wrench was thrown into the works with passage of the Surface Mining Control and Reclamation Act of 1977.

Jan 12, 1979

By T. M. Morris, F. M. Lewis, W. C. Lay, Gordon M. Bell

Part I of this chapter is concerned with the description of and metallurgical data pertaining to the flotation circuits used in the London mill of the Tennessee Copper Co., at Copperhill, Tenn. The ores treated at the London mill are massive complex sulfides, in which pyrrhotite and pyrite are the predominant minerals. Other sulfides are chalcopyrite and sphalerite; magnetite is also of economic value. The approximate mineralogical analysis of the ore is shown in Table 1. [ ] The chalcopyrite and sphalerite are closely associated with pyrrhotite as shown by the tracings of micrographs (Fig. I), which are representative of the mill feed. Fig. la illustrates the type of locking between pyrrhotite and chalcopyrite; Fig. lb illustrates the way in which sphalerite is attached. Thesephotographs indicate that it is not practical to break all of these attachments. Hence, in order to produce concentrates with satisfactory grades and recoveries, most of the locked chalcopyrite particles must be recovered into the copper concentrate, and the locked sphalerite-pyrrhotite particles must be separated from the iron concentrate. A copper concentrate, a zinc concentrate, and an iron concentrate are made. Typical metallurgical results are tabulated in Table 2. HISTORICAL In 1922 the London mill started as a copper concentrator, with a capacity of 300 tpd, and in 1926 an additional flotation circuit was added to recover the iron sulfide remaining in the copper tailing. In 1927 a zinc flotation circuit was installed between the copper and the iron flotation circuits. This procedure was not satisfactory because the iron recovery was low, due to the

Jan 1, 1962

By M. H. Pilkuhn, H. Rupprecht

p layers on n-type substrates of GaAs were prepared by difhsion of zinc into these substrates. Experimental details about the diffusion technique will be presented. It will be shown that inhomogeneity in the substrate doping level and crystal shucture defects cause nonplanarity in the junction plane. These nonplanarities give rise to high threshold current densities. From incremental sheet-conductivity measurements the zinc profile is derived. Data about surface concentration and gradient of the zinc concentration at the junction are presented. Finally, some results of laser diodes, which were made of wafers with extremely planar diffusion fronts, are discussed. ThE investigations reported here are part of a program concerned with the materials aspect in the fabrication of GaAs laser diodes. This includes studies of the influence of crystal defects introduced both during the growth of the crystal and as a consequence of subsequent diffusion. Compared with the progress made in the investigation of structure defects, for instance by X-ray microscopy in materials like silicon, no similar results are known so far for the case of GaAs. The further progress in laser diodes will depend very much upon our knowledge of these structure defects and subsequently upon our ability to avoid them. Laser diodes of GaAs had been made mostly by diffusing an acceptor impurity, normally zinc, into an n-type substrate. This procedure was found more convenient than the inverse one for various technical reasons. We will follow this line and restrict ourselves to zinc diffusion only in this paper. DIFFUSION TECHNIQUES AND EXPERIMENTAL DETAIL In order to set a refgrence for our experiments, we used a standard procedure for the diffusion runs. The diffusions were carried out in a sealed quartz tube for 2-1/2 hr at 850°C. One milligram zinc arsenide (ZnAsz) per cu cm of the tube volume served as zinc source. Under these conditions the junction depth was between 25 and 30 p. It is assumed, according to the investigations of the zinc arsenide system by V. Lyons and V. ilvestri,' that ZnAs2 dissociates completely at 850°C into ZnsAsz and Asg. Since there is a condensed phase of ZnsAs2 in the tube at 850°C, the partial pressure of zinc is controlled by the pressure of the arsenic formed by the dissociation of ZnAs2. Due to the fact that the zinc partial pressure resulting from the dissociation of ZnsAsz is only a weak function of the partial pressure of arsenic, the amount of the initial ZnAs2 is not very critical. Experimentally, we found that the junction depth, as well as the surface concentration, was practically the same, if the ingots of ZnAs2 varied between 0.2 and 5.0 mg per cu cm. The wafers were oriented with the main faces in (100). Surface damage due to cutting and lapping was removed by a chemical-etch treatment in a rotating beaker (etch solution: HzSOr, H202, and HzO in a ratio 3:l:l). The GaAs substrate material was n type and doped with tellurium, selenium, silicon, or germanium. It was grown by means of horizontal or Czochralski techniques. After the diffusion process, junction depth and planarity were checked either by grooving with a

Jan 1, 1964

Long range expansion plans begun in 1966 by The International Nickel Co. of Canada, producer of over 50% of the free world supply of the white metal, are so mammoth as to give rise to the speculation that something might have to burst at the seams. From an annual level of capital expenditure of $35 to $70 million, the company jumped in 1967 to $145 million in new capital investment and will come close to $200 million in 1968. Inco expects to spend $700 million in the next five years, beginning in 1968, for new mines and surface facilities in Canada. The program involves the opening of nine new mines within the next 3 1/2 years, expansion of producing mines, and construction of new plants and modernization and expansion of established ones to process the increased ore production. Beyond this, the company is committed deeply in developing new sources of nickel abroad. Any one of these new projects, if proven economic, would necessitate expenditures of about $100 million or more. For Inco, the economic strain was relieved without a rupture this spring when Henry S. Wingate, company chairman, reported' at the stockholders annual meeting that $150 million had been raised by the sale of bonds. This marked the first time in 32 years that the company had gone into debt.

Jan 10, 1968

By P. K. Weimer

Coinpletely integrated thin-film circuits inco?,porating more than 1000 active and passive elements have been fabricated reproducibly in the laboratory by evaporation of- all components. A 180-stage modified shift register comprising 540 CdSe TFT's, 360 resistovs, and 180 capacitors was deposited upon a glass substrate during one pump-down of the vacuum systeitl. Experimental units have been operated for more than 5000 hr at temperatures uP to 85°C without failure of any slages. The present pupper reviews the charvactevistics of evaporated thin-film transistors (TFT's) and discusses their application to integrnted circuils. INTEGRATED circuits most widely used today are based upon silicon technology, with the circuits formed on the surface of a block of single-crystal silicon1 or on a block of sapphire 2,3 upon which a thin layer of silicon has been deposited. Transistor patterns and interconnections are defined by photographic procedures using photoresist masking. Large groups of transistors are produced in batches which undergo many processing steps, some of which are carried out at elevated temperatures. Passive elements are formed by treatment of the semiconductor surface or are deposited by evaporation alongside the active elements. The size and complexity of the circuits are limited by defects in the devices and by the size of the available single-crystal chips. Capacitative coupling to the semiconducting substrate may also limit useful size and frequency response of the circuits. An alternative approach to integrated circuits is based upon the deposition by evaporation of all circuit components upon a noncrystalline, insulating substrate such as glass.4 Thin-film field-effect transistors,1'6 known as TFT's, can be deposited in large arrays on glass or plastic substrates at the same time the associated passive elements are being deposited. Although still in the research stage the all-evaporated approach is expected to offer certain advantages for many applications. In particular, the use of thin films upon a noncrystalline substrate offers the prospect of producing complex, large-area circuits not now feasible with single-crystal silicon. Important applications of this type include memory arrays for computers and imaging devices for television. The ease with which the evaporated TFT's can be deposited may permit continuous, automated production methods not possible with high-temperature batch processing. Recent advances7'8 in the fabrication of thin-film transistors have led to greatly improved reproduci-bility and life of the TFT's. Experimental circuits having over 1000 active and passive elements deposited upon a common glass substrate are currently being produced in the laboratory. The present paper reviews recent progress in the development of the TFT and in its application to integrated circuits. I) DESCRIPTION OF THE THIN-FILM FIELD-EFFECT TRANSISTOR The TFT is a field-effect transistor of the type having the control gate separated from the semiconductor by a thin insulating spacer. Although its operation resembles that of the silicon MOS transistorg its construction is based entirely on thin-film techniques. Fig. 1 shows a cross-sectional view of an evaporated TFT deposited upon a glass substrate compared with a silicon MOS transistor deposited upon single-crystal sapphire.3 The semiconductor in the TFT is a poly crystal line layer, of a material which can be readily evaporated, such as cadmium sulfide, cadmium selenide,l0 or tellurium." Silicon monoxide layers have usually served as the gate insulator, but other oxides, sulfides, and fluorides may be used. Film thicknesses range from a few hundred to a few thousand angstroms. The source, drain, and gate electrodes in the TFT are of metal. Qpical source-drain gap dimensions are 0.0003 x 0.030 in., with a gate strip whose width slightly overlaps the source and drain. The source and drain electrodes should make low impedance contacts to the semiconductor. With cadmium sulfide films, gold is a satisfactory material for underlying electrodes, while aluminum is preferable for overlying electrodes.12 Considerable variation in design of the TFT is permissible, with the electrodes being

Jan 1, 1967

At the request of representatives of the Treasury Department, President Winchell appointed the following committee, which .held a two-day conference with the Treasury representatives in Washington Oil Oct. 6 and 7 to aid in deciding upon the principles of mine taxation to he adopted by the Government. The results of this conference, which is not yet concluded, will be published in a future Bulletin.

Jan 11, 1919

[President MRS. REED W. HYDE 84 Mountain Ave. Summit, N. J. First Vice-President MRS. WILLIAM A. SCHEUCH 37 Trent St. Great Kills, S. I., N. Y. Second Vice-President MRS. RUSSELL B. PAUL 6 Brooklands Bronxville, N. Y. Third Vice-President MRS. JOHN C. BURTON 271 Fox Meadow Rd. Scarsdale, N. Y. Fourth Vice-President MRS. DANIEL C. JACKLING Redwood City R. F. D., Woodside, Calif.]

Jan 1, 1940

By J. A. Clum, R. W. Heins, T. D. Tiemann

The use of Na-montmorillonite clay binders (Western Bentonite) in the pelletizing of iron ore concentrates is well established as is the idea that alternative binders must be found. 1-6 This note summarizes work done7 in evaluating a Wisconsin montmorillonite clay binder. The clay occurs in irregualr beds overlying the Prairie du Chien Dolomite and the St. Peters Sandstone near Hersey, St. Croix County.

Jan 1, 1978

By J. T. Eash, E. M. Wise

Platinum and palladium are the most generally useful, most ductile and least rare members of the platinum family. They have many important applications in the pure state but for other applications it is frequently desirable to harden them and otherwise modify their properties by alloying small amounts of the other platinum group metals with them. These alloys are frequently required to withstand very drastic forming operations and to possess certain mechanical properties to fulfill specific requirements. For these reasons a knowledge of the tensile properties and annealing characteristics of pure platinum and palladium as well as their more useful commercial alloys is important to the user and the fabricator. The present work was undertaken to fill this need. Rather brief (5 min.) annealing treatments were employed to render the data of maximum practical value and all tests were conducted upon 0.050-in. dia. wire, initially reduced 50 per cent in area by cold drawing, for the same reason. Conclusions 1. Pure (thermocouple grade) platinum reduced 50 per. cent by cold drawing exhibits the following tensile properties: ultimate tensile strength, 36,000 lb. per sq. in.; proportional limit, 27,000 lb. per sq. in.; elongation, 2.5 per cent in 2 in.; reduction in area, 95 per cent. When fully annealed by treatment at 1100°C. its properties are: ultimate tensile strength, 20,700 lb. per sq. in.; elongation, 30 per cent in 2 in.; reduction in area, 93 per cent. 2. The addition of alloying elements in moderate amounts markedly increases the strength and annealing temperature without much detriment to the ductility. The behavior and properties of variously hardened platinum alloys are considered in some detail. The behavior of a 20 per cent iridium

Jan 1, 1935

By J. T. Eash, E. M. Wise

Platinum and palladium are the most generally useful, most ductile and least rare members of the platinum family. They have many important applications in the pure state but for other applications it is frequently desirable to harden them and otherwise modify their properties by alloying small amounts of the other platinum group metals with them. These alloys are frequently required to withstand very drastic forming operations and to possess certain mechanical properties to fulfill specific requirements. For these reasons a knowledge of the tensile properties and annealing characteristics of pure platinum and palladium as well as their more useful commercial alloys is important to the user and the fabricator. The present work was undertaken to fill this need. Rather brief (5 min.) annealing treatments were employed to render the data of maximum practical value and all tests were conducted upon 0.050-in. dia. wire, initially reduced 50 per cent in area by cold drawing, for the same reason. Conclusions 1. Pure (thermocouple grade) platinum reduced 50 per. cent by cold drawing exhibits the following tensile properties: ultimate tensile strength, 36,000 lb. per sq. in.; proportional limit, 27,000 lb. per sq. in.; elongation, 2.5 per cent in 2 in.; reduction in area, 95 per cent. When fully annealed by treatment at 1100°C. its properties are: ultimate tensile strength, 20,700 lb. per sq. in.; elongation, 30 per cent in 2 in.; reduction in area, 93 per cent. 2. The addition of alloying elements in moderate amounts markedly increases the strength and annealing temperature without much detriment to the ductility. The behavior and properties of variously hardened platinum alloys are considered in some detail. The behavior of a 20 per cent iridium

Jan 1, 1935